Related
Hellò, I have a problem during the procedure to get the phone upgraded.
During that procedure, it asks me to shut off the phone, then wait for 5 seconds and then plug the microusb in while holding the volume down key. But nothing happen!
is there something wrong in the procedure?
do I have to do something else to upgrade it?
My OS in Windows Seven.
please, help!!!
thank you
fausto
fcasini said:
Hellò, I have a problem during the procedure to get the phone upgraded.
During that procedure, it asks me to shut off the phone, then wait for 5 seconds and then plug the microusb in while holding the volume down key. But nothing happen!
is there something wrong in the procedure?
do I have to do something else to upgrade it?
My OS in Windows Seven.
please, help!!!
thank you
fausto
Click to expand...
Click to collapse
Thats sounds like a driver issue, Make sure you have installed the drivers before trying to connect in flashmode.
Install pccompanion and run it then attach phone whilst it is turned on. That will install the correct drivers, then it should work
gregbradley said:
Thats sounds like a driver issue, Make sure you have installed the drivers before trying to connect in flashmode.
Install pccompanion and run it then attach phone whilst it is turned on. That will install the correct drivers, then it should work
Click to expand...
Click to collapse
thank you Greg for reply. I have uninstalled both SUS and Pc Companion and then reinstalled SUS first but once launched I receive an error message and SUS closes.
Then I have uninstalled SUS and reinstalled Pc Companion, then connected the phone and started the upgrade procedure. Unfortunately, it stops when asks me to plug in the usb cable while pressing the volume down key, and then nothing happens... again...
On the drive page of Windows Seven, there is: "Apple Mobile Device Usb Driver: ready for use"
Tryed also on another pc but the same thing happens
what can I do to upgrade my T?
thanks
fausto
fcasini said:
thank you Greg for reply. I have uninstalled both SUS and Pc Companion and then reinstalled SUS first but once launched I receive an error message and SUS closes.
Then I have uninstalled SUS and reinstalled Pc Companion, then connected the phone and started the upgrade procedure. Unfortunately, it stops when asks me to plug in the usb cable while pressing the volume down key, and then nothing happens... again...
On the drive page of Windows Seven, there is: "Apple Mobile Device Usb Driver: ready for use"
Tryed also on another pc but the same thing happens
what can I do to upgrade my T?
thanks
fausto
Click to expand...
Click to collapse
It shouldnt be an apple device.
make sure you have installed the drivers. Did you do this
1) Uninstall all sony programs (PCCompanion, SUES etc)
2) Reinstall PCCompanion
3) OPen PCCompanion
4) Turn on phone and attach to PC
5) Let the drivers install
6) Then try to update
gregbradley said:
It shouldnt be an apple device.
make sure you have installed the drivers. Did you do this
1) Uninstall all sony programs (PCCompanion, SUES etc)
2) Reinstall PCCompanion
3) OPen PCCompanion
4) Turn on phone and attach to PC
5) Let the drivers install
6) Then try to update
Click to expand...
Click to collapse
thank you again Greg, I did it but without any result.
It asks me to keep the volume down key pushed and then connect the usb cable but once done, nothing still happens...
Should I turn off the Usb debug option?
I start thinking that my phone will never be updated...
bye
have a nice day
fausto
No, you need USB debugging enabled and you should be in MTP mode for your connectivity in settings
Does the computer make any noise when you connect?
Does the phone do anything when you connect, like power up, or do you get a green LED light up?
Try this, and report back
Download, instal and run flash tool
Try to connect to that in flash mode. Post here what flash tool says
Sent from my LT30p xda premium app.
How do I customise the signature on xda premium app?
gregbradley said:
No, you need USB debugging enabled and you should be in MTP mode for your connectivity in settings
Does the computer make any noise when you connect?
Does the phone do anything when you connect, like power up, or do you get a green LED light up?
Try this, and report back
Download, instal and run flash tool
Try to connect to that in flash mode. Post here what flash tool says
Click to expand...
Click to collapse
Hi Greg, and thank for your patience,
When I connect the phone to the computer, it sounds like when I connect a usb device.
When the phone is connecte to the computer, le notification led light up, red first then green when battery reach 100%.
Currently, I have downloaded "Emma" but I am still waiting to receive the email to activate the account.
When I will finally receive it, I can tell you something more.... sorry(
ciao
fausto
fcasini said:
Hi Greg, and thank for your patience,
When I connect the phone to the computer, it sounds like when I connect a usb device.
When the phone is connecte to the computer, le notification led light up, red first then green when battery reach 100%.
Currently, I have downloaded "Emma" but I am still waiting to receive the email to activate the account.
When I will finally receive it, I can tell you something more.... sorry(
ciao
fausto
Click to expand...
Click to collapse
Please download flashtool.
Its in the first thread in the development section.
Install it, and run it.
Attach the phone whilst it is turned on and tell me what flashtool says....
Then try to attach in flashmode whist flashtool is open and tell me what it says
Please follow these instructions so that i can help you
gregbradley said:
Please download flashtool.
Its in the first thread in the development section.
Install it, and run it.
Attach the phone whilst it is turned on and tell me what flashtool says....
Then try to attach in flashmode whist flashtool is open and tell me what it says
Please follow these instructions so that i can help you
Click to expand...
Click to collapse
Hi Greg,
I have downloaded and installed Flashtool but when I try to run it i get the attached error message and of course it doesn't start. Both antivirus and firewall were disabled.
What do you mean when you say: "Then try to attach in flashmode"? Perhaps a special combination of keys during boot?
thanks
fausto
fcasini said:
Hi Greg,
I have downloaded and installed Flashtool but when I try to run it i get the attached error message and of course it doesn't start. Both antivirus and firewall were disabled.
What do you mean when you say: "Then try to attach in flashmode"? Perhaps a special combination of keys during boot?
thanks
fausto
Click to expand...
Click to collapse
Thats a windows issue, all I can suggest is removing all sony programs, rebooting and starting again. Also, make sure you have java installed.
Or try another machine, to see if its your computer thats at fault.
Once you have flashtool installed properly and it runs properly we can continue.
Hi Greg,
finally it works!!!.
I had to change the property of flashtool.exe and set it to be compatible with Windows 2000.... that's all...
Now, once connected the phone, flashtool reports:
20/004/2012 20:04:23 - INFO - <- This level is successfully initialized
20/004/2012 20:04:23 - INFO - Flashtool Version 0.9.9.0 built on 2012-11-13 22:53:30
20/004/2012 20:04:23 - INFO - You can drag and drop ftf files here to start flashing them
20/004/2012 20:04:32 - INFO - Device connected with USB debugging on
20/004/2012 20:04:35 - INFO - Connected device : LT30
20/004/2012 20:04:35 - INFO - Installed version of busybox : N/A
20/004/2012 20:04:35 - INFO - Android version : 4.0.4 / kernel version : 3.0.8+1.0.21100-02378-gcca969a / Build number : 7.0.A.1.303
and now?
thank you
fausto
good to hear, so my initial thoughts were correct.
glad it worked out for you. and dont forget to change your title to solved.
Edit the OP and click on advanced.
thank you Greg, but now what I have to do? Install PCC or SUS and try to update or I can use Flashtool too?
bye
fausto
fcasini said:
thank you Greg, but now what I have to do? Install PCC or SUS and try to update or I can use Flashtool too?
bye
fausto
Click to expand...
Click to collapse
Instal pccompanion and update that way,
If there is no official update for you then you can flash an updated ftf in flashtool, or root and/or unlock your bootloader to flasha custom rom.
Its all in the all in the one thread, give it a good read
While You were writing, I have installed Sus but with the same bad result:
I get the attached error message, and log file reports:
!SESSION 2012-12-21 14:12:34.116 -----------------------------------------------
eclipse.buildId=unknown
java.version=1.6.0_24
java.vendor=Sun Microsystems Inc.
BootLoader constants: OS=win32, ARCH=x86, WS=win32, NL=it_IT
Command-line arguments: -os win32 -ws win32 -arch x86
!ENTRY org.eclipse.osgi 4 0 2012-12-21 14:13:02.748
!MESSAGE Application error
!STACK 1
java.lang.IllegalStateException: Must create UI first
at com.sonyericsson.cs.ma3.updateservice.ui.e.j.a(j.java)
at com.sonyericsson.cs.ma3.updateservice.ui.e.j.a(j.java)
at com.sonyericsson.cs.ma3.updateservice.UpdateServiceApplication.start(UpdateServiceApplication.java)
at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:196)
at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLauncher.java:110)
at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.java:79)
at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:344)
at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(Unknown Source)
at java.lang.reflect.Method.invoke(Unknown Source)
at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:622)
at org.eclipse.equinox.launcher.Main.basicRun(Main.java:577)
at org.eclipse.equinox.launcher.Main.run(Main.java:1410)
I will try with PCC too but I think that the result will be probably the same as before.
I will look forward to know hot to flash an updated ftf.
thnak you
see you soon.
fausto
i have the same problem with Xperia T and Windows 8.
I have tried the driver to install.
And now after i plug the microusb in while holding the volume down key, is my Xperia charged and nothing happen.
Hi, here is flashtool reports:
23/045/2012 21:45:30 - INFO - <- This level is successfully initialized
23/045/2012 21:45:30 - INFO - Flashtool Version 0.9.0.0 built on 2012-07-19 22:57:15
23/045/2012 21:45:30 - INFO - You can drag and drop ftf files here to start flashing them
23/045/2012 21:45:35 - INFO - Device disconnected
23/045/2012 21:45:46 - INFO - Device connected in flash mode
23/045/2012 21:45:56 - INFO - Device disconnected
23/046/2012 21:46:49 - INFO - Device connected with USB debugging off (My Phone is now in charge-mode)
23/046/2012 21:46:49 - INFO - For 2011 devices line, be sure you are not in MTP mode
Click to expand...
Click to collapse
But USB debugging is ON.
try to keep the volume down key pushed for more. I kept it pushed a lot until the phone started in "safe mode", then something has happen because for two times the screen of the phone has shown the message "downloading upgrade" and now the note on the status bar " a new firmware is available....195" seems to be disappeared...
Some widgets are disappeared too but now they work again. The keyboard also is back as chinese as in origin.
ciao
fausto
EDIT: I was wrong... nothing has changed. This post can be deleted.
and now is my phone on, here is flashtool reports:
23/016/2012 22:16:40 - INFO - <- This level is successfully initialized
23/016/2012 22:16:40 - INFO - Flashtool Version 0.9.0.0 built on 2012-07-19 22:57:15
23/016/2012 22:16:40 - INFO - You can drag and drop ftf files here to start flashing them
23/016/2012 22:16:45 - INFO - Device connected with USB debugging on
23/016/2012 22:16:45 - ERROR - Cannot identify your device.
Click to expand...
Click to collapse
than muss i chose one device from the list. But there isn't Xperia T. :crying:
(My OS is Windows 8 64Bit)
---------- Post added at 10:57 PM ---------- Previous post was at 10:22 PM ----------
Hi, i have a good news. Sony PC Companion and Sony Update Service have recognized my Xperia T. Not 100%, i muss wait for the download of new firmware.
I don't know what was the problem. May be was USB 3.0 or my Mouse or ....
I have all uninstalI and install Flasttool from our 4rum, than Emma from Sony. restart PC.
I have plugged cable in USB 2.0, (earlier was USB 3.0; another device out) than start Emma. Emma has recognized my Xperia T.
and now come the magic. All of programs can recognize my Xperia.
Now i'm download the update for my Phone from Sony Update Service. If that is successful, i will say u.
---------- Post added at 11:08 PM ---------- Previous post was at 10:57 PM ----------
wonderful!!!
the update was successful. Thank you very much for your helps!!!:good:
fcasini said:
try to keep the volume down key pushed for more. I kept it pushed a lot until the phone started in "safe mode", then something has happen because for two times the screen of the phone has shown the message "downloading upgrade" and now the note on the status bar " a new firmware is available....195" seems to be disappeared...
Some widgets are disappeared too but now they work again. The keyboard also is back as chinese as in origin.
ciao
fausto
EDIT: I was wrong... nothing has changed. This post can be deleted.
Click to expand...
Click to collapse
is your update too OK? i hope that is ok. The original update 4.1 for Xperia T come soon.
Guys, has anyone faced following problem-
The Sony pc companion recognizes my phone just fine and even tells me that I have new build to install. I was able to download but it get stuck on step 2 where on screen it asks me to put phone in a download mode by shutting it off, plugging in sub while holding volume down button.
I have followed all these steps properly and even confirmed with tech support but the pc companion just stays there and no install is initiated.
I have been researching in the forums but no luck so far.
Details-
Xperia Z C6602
Current build - 10.1.A.1.350
Update build from pc companion - 10.1.A.1.434.
Swraj
Download update service from sony website and try.
Try to change the usb port,and reboot your pc.
Sent from my SO-02E using xda premium
I have all of those steps before posting in this forum. No luck so far
Try another pc, another cable?
Disable any antivirus.
Sent from my SO-02E using xda premium
swrajjoshi said:
Guys, has anyone faced following problem-
The Sony pc companion recognizes my phone just fine and even tells me that I have new build to install. I was able to download but it get stuck on step 2 where on screen it asks me to put phone in a download mode by shutting it off, plugging in sub while holding volume down button.
I have followed all these steps properly and even confirmed with tech support but the pc companion just stays there and no install is initiated.
I have been researching in the forums but no luck so far.
Details-
Xperia Z C6602
Current build - 10.1.A.1.350
Update build from pc companion - 10.1.A.1.434.
Swraj
Click to expand...
Click to collapse
Disable Anti-Virus
**Disable Firewall**
Restart PC
>> and try with Update Service Tool
I tried the same steps on another laptop I have after disabling the anti virus no luck. I tried with update service tool as well, same result.
Steps done-
1. Launch pc companion/update service
2. Allow above apps to download the .434 as steps on their wizard.
3. App takes me to step two.
4. Disconnect usb cable from phone and pc.
5. Shutodown phone, wait 30+ secs
6. Plug in the usb into laptop
7. Plug in usb into phone and press volume down while doing it.
8. I notice the indicator blinks red and green but then nothing.
Also, I can't get OTA upgrade as the new build doesn't get listed on my phone's update center
This is my brand new Xperia Z.
Are there any other flash tools I can use? If yes, where can I download the ..434 stock ROM
The same thing happens to me...ive tried everyyything
ligerblitz said:
The same thing happens to me...ive tried everyyything
Click to expand...
Click to collapse
Hold volume up+ power for 15 seconds till you have 3 vibrations,this is like removing the battery and putting it back.
And try again.
Sent from my C6602 using xda premium
Ok I had that mcafee program on, i un-installed it and it worked
The anti virus was causing trouble for me too! For some reason it didn't work before but when I tried same thing on my alienware... it worked !
Thank you for all help! :good:
I am in an awkward situation.
xperia z, 4.2.2 244 rooted stock rom, bootloader locked, usb debug mode off, recovery not installed.
I accidentally corrupted build.prop and the phone bricked.
I cannot use flashtool to flash the stock rom back because usb debug mode is off.
I cannot use Sony update service Pro to force update because it said that "your phone already has the latest available software installed".
I cannot use PC Companion to repair because the software said that "Sony update engine doesn't have software available for your phone".
Please help.
wmiswm said:
I am in an awkward situation.
xperia z, 4.2.2 244 rooted stock rom, bootloader locked, usb debug mode off, recovery not installed.
I accidentally disrupted build.prop and the phone bricked.
I cannot use flashtool to flash the stock rom back because usb debug mode is off.
I cannot use Sony update service Pro to force update because it said that "your phone already has the latest available software installed".
I cannot use PC Companion to repair because the software said that "Sony update engine doesn't have software available for your phone".
Please help.
Click to expand...
Click to collapse
Use PC companion but try use repair phone not update. Wait till all phone model showing up than choose your model phone. btw, your phone must off.
than follow instruction there... wil take 1～2 hour for repair.
Hope you can solve your problem. ill take screen shoot when im home later than post here..
Sent from my C6602 using xda premium
YudiA1 said:
Use PC companion but try use repair phone not update. Wait till all phone model showing up than choose your model phone. btw, your phone must off.
than follow instruction there... wil take 1～2 hour for repair.
Hope you can solve your problem. ill take screen shoot when im home later than post here..
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
Thank you very much for your reply. But I am already using the PC Companion repair option, and the response is as stated above.
flashtool is all what you need,read the instructions
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Reply
wmiswm said:
I cannot use flashtool to flash the stock rom back because usb debug mode is off
Click to expand...
Click to collapse
You can use Flashtool to flash stock rom, doesn't matter if usb debug mode is on or off (only needed to install recovery or to root)
Download stock rom, install flashtool + drivers and follow screen instructions.. Good Luck! :good:
J have the same problem, yesterday j installed cyanogenmod, now xperia Z was on SONY logo and j can't flash original firmware on flashtool, j can only flash original kernel, but is still on sony logo
SUS says that hasn't new firmware for my phone.
What can j do ????
Thanks in advance
gm007 said:
flashtool is all what you need,read the instructions
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
many thanks, done.
shysparrow said:
You can use Flashtool to flash stock rom, doesn't matter if usb debug mode is on or off (only needed to install recovery or to root)
Download stock rom, install flashtool + drivers and follow screen instructions.. Good Luck! :good:
Click to expand...
Click to collapse
yes, you are right. Yesterday I check everything on the right panel and it does not work. Today I leave all option unchecked and flash properly. Many thanks anyway.
maxam73 said:
J have the same problem, yesterday j installed cyanogenmod, now xperia Z was on SONY logo and j can't flash original firmware on flashtool, j can only flash original kernel, but is still on sony logo
SUS says that hasn't new firmware for my phone.
What can j do ????
Thanks in advance
Click to expand...
Click to collapse
Just follow the flashtool instruction and re-flash the stock rom first, everything will return to unroot stated. Reroot then and try again.
wmiswm said:
Just follow the flashtool instruction and re-flash the stock rom first, everything will return to unroot stated. Reroot then and try again.
Click to expand...
Click to collapse
Maybe j have other kind of problem, j tried with flashtool but it doesn't start flashing when in flashmode, after a minute phone boots itself continuosly on sony logo.
j tried several times with different PC and different ftf file.
j hope to solve this problem, but how...
maxam73 said:
Maybe j have other kind of problem, j tried with flashtool but it doesn't start flashing when in flashmode, after a minute phone boots itself continuosly on sony logo.
j tried several times with different PC and different ftf file.
j hope to solve this problem, but how...
Click to expand...
Click to collapse
Try this way bro.. Done in many Xperia here..
Solving Bootloop phone/Flash Tool can't Detect your phone.
Your Phone Must Off!! and not connected !!
1. Open Pc Companion
2. Click update on Red ellipse (in Picture 1)
3. Start on Phone/tablet Update (in Picture 2)
4. Click Repair on Next Screen
5. in Next Screen, Read that warning Click Continue if you OK
6. Next Step click on Red Circle than Next...
7. Wait initializing Software (10~30 mnt) or depend your ISP speed
8. After initializin9 All Xperia Phone List Will Show Up.
Choose What Xperia Phone Will you repair ( I choose XZ) than Next..
9. Follow instruction On picture.
( Connect USB on your Phone while Press Vol down )
10. if not Start.. Unplug usb and try plug again ==> same no 9)
11. After start.. Waiting 1~2 Hours till done.
(Read Warning There )
Sent from my C6602 using xda premium
YudiA1 said:
Try this way bro.. Done in many Xperia here..
Solving Bootloop phone/Flash Tool can't Detect your phone.
Your Phone Must Off!! and not connected !!
1. Open Pc Companion
2. Click update on Red ellipse (in Picture 1)
3. Start on Phone/tablet Update (in Picture 2)
4. Click Repair on Next Screen
5. in Next Screen, Read that warning Click Continue if you OK
6. Next Step click on Red Circle than Next...
7. Wait initializing Software (10~30 mnt) or depend your ISP speed
8. After initializin9 All Xperia Phone List Will Show Up.
Choose What Xperia Phone Will you repair ( I choose XZ) than Next..
9. Follow instruction On picture.
( Connect USB on your Phone while Press Vol down )
10. if not Start.. Unplug usb and try plug again ==> same no 9)
11. After start.. Waiting 1~2 Hours till done.
(Read Warning There )
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
Solved...j know that phones must be off, the problem was flashtool, j used other version (beta 4) on other pc running xp instead of win7 and all goes good.
Thanks to all for helping me
Doesnt work.
I cant use flashtool, period.
Are there anyother methods?
theVenerable said:
Doesnt work.
I cant use flashtool, period.
Are there anyother methods?
Click to expand...
Click to collapse
The above didn't work for me because I received error based on my type of phone.
This guide however did help: http://forum.xda-developers.com/showthread.php?t=2240614
I had to reboot windows to a settings to enable unsigned drivers. Installed Flashtool and it's drivers,
First unlocked the bootloader(BLU button, got the IMEI, used the sony form (http://unlockbootloader.sonymobile.com/instructions))
Then I downloaded the stock sony xperia z ftf image, placed it in Flashtool's firmware folder, then flashed it (flash device > flash mode).
Now my phone's working again.
HTH,
George
brick,unbrick,xperia z problem,flashtool
My OS phone in recovery mode (root) got deleted And when I turn on phone stuck on Sony logo And when it is connected to the computer showing error your USB not recognized and Flash mode for use Flashtool doesn't work and the same error shows what should i do?
shayanster said:
My OS phone in recovery mode (root) got deleted And when I turn on phone stuck on Sony logo And when it is connected to the computer showing error your USB not recognized and Flash mode for use Flashtool doesn't work and the same error shows what should i do?
Click to expand...
Click to collapse
If you still can enter custom recovery, you only need flash rom and (with) suitable kernel.
If not, you need Flashtool.
- make sure you have the newest version of flashtool and driver
- connect your phone to pc.
- when computer show error about usb not recognized, go to computer management - device manager. Find something in universal serial bus controller list that have yellow triangle and exclamation mark. right click and remove it
- disconnect your phone then reboot your pc
- install flashtool and driver, reboot pc again
- connect your phone to pc. Now, it should detect your phone.
- do flashing procedure
cmiiw
visualfighter said:
If you still can enter custom recovery, you only need flash rom and (with) suitable kernel.
If not, you need Flashtool.
- make sure you have the newest version of flashtool and driver
- connect your phone to pc.
- when computer show error about usb not recognized, go to computer management - device manager. Find something in universal serial bus controller list that have yellow triangle and exclamation mark. right click and remove it
- disconnect your phone then reboot your pc
- install flashtool and driver, reboot pc again
- connect your phone to pc. Now, it should detect your phone.
- do flashing procedure
cmiiw
Click to expand...
Click to collapse
Thanks for the answer I tried all ways but the problem is not solved .I think the only solution is JTAG box
shayanster said:
Thanks for the answer I tried all ways but the problem is not solved .I think the only solution is JTAG box
Click to expand...
Click to collapse
To use Flashtool put phone in flashmode, it will not work in recovery mode
To put phone in flashmode
Hold power + both volume keys
wait till you feel three vibrations.
Make sure you have installed Z drivers flashmode drivers & fastboot drivers(Setup fille is in driver folder of flashtool)
Keep FTF file in firmware folder of flashtool
Start flashtool
Click the thunder button
select flashmode
select the FTF file
When it tells you to connect phone
Hold volume down key and connect USB it should start flashing
androidtweaker1 said:
To use Flashtool put phone in flashmode, it will not work in recovery mode
To put phone in flashmode
Hold power + both volume keys
wait till you feel three vibrations.
Make sure you have installed Z drivers flashmode drivers & fastboot drivers(Setup fille is in driver folder of flashtool)
Keep FTF file in firmware folder of flashtool
Start flashtool
Click the thunder button
select flashmode
select the FTF file
When it tells you to connect phone
Hold volume down key and connect USB it should start flashing
Click to expand...
Click to collapse
when it is connected into flashmode the computer showing error your USB not recognized
shayanster said:
when it is connected into flashmode the computer showing error your USB not recognized
Click to expand...
Click to collapse
Is it Windows 7 or 8?
Some days ago I have got a new system update for Sony xperia SP (12.1.A.0.266). So I download the update ( via update center) and then tap on install button. Then the phone restart with sone new animation. Then after a while it shows a error message "Update couldn't be installed" and then another error message "Update center has stopped." Then I unroot and reset ( hard factory reset) my mobile and again try to update, but again failed. So how to fix this problem???
If I update using pc companion via PC, shall I face the same problem?????? Please help me...
Sourav-21 said:
Some days ago I have got a new system update for Sony xperia SP (12.1.A.0.266). So I download the update ( via update center) and then tap on install button. Then the phone restart with sone new animation. Then after a while it shows a error message "Update couldn't be installed" and then another error message "Update center has stopped." Then I unroot and reset ( hard factory reset) my mobile and again try to update, but again failed. So how to fix this problem???
If I update using pc companion via PC, shall I face the same problem?????? Please help me...
Click to expand...
Click to collapse
You should definetly try to update via PC Companion
Windows 8.1
I use Windows 8.1. So I can't update using Sony PC companion. Pc companion is not supported with Windows 8.1.
Sourav-21 said:
I use Windows 8.1. So I can't update using Sony PC companion. Pc companion is not supported with Windows 8.1.
Click to expand...
Click to collapse
I am pretty sure there are some quite useful guides out there
SUS
Can I use Sony Update Service (SUS) for windows 8.1???? Is Sony Update Service compatible with Windows 8.1????
Why you dont flash stock using flastool..
Sourav-21 said:
Can I use Sony Update Service (SUS) for windows 8.1???? Is Sony Update Service compatible with Windows 8.1????
Click to expand...
Click to collapse
Yes it is. I'm Using 8.1 Enterprise. First faild with PC Companion, then tried SUS. It works perfectly.
Hey!
So i have done this https// >> android.stackexchange.com/questions/61279/sony-xperia-zr-fastboot-driver <<
and i got the right driver inn. In device manager i get under Android Phone "Android Bootloader Interface"
But now i dont know what to do since i can't turn on my phone.
I have done the Sony PC Companion update restore thing. But still it wont turn on.
Thanks for any help!