i had a tab i957 its stuck on logo . cant go to recovery ,but i can enter download mode . when i add I957UCLK4_ATTLK4_ATT_USA_Android_4.0.4 file to flashin odin . its says no pit partition found. cant flash recovery also . attached pics too .
odin log
<ID:0/034> Added!!
<ID:0/034> Odin v.3 engine (ID:34)..
<ID:0/034> File analysis..
<ID:0/034> SetupConnection..
<ID:0/034> Initialzation..
<ID:0/034> Get PIT for mapping..
<ID:0/034> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/034> Removed!!
<ID:0/034> Added!!
<ID:0/034> Odin v.3 engine (ID:34)..
<ID:0/034> File analysis..
<ID:0/034> SetupConnection..
<ID:0/034> Initialzation..
<ID:0/034> Get PIT for mapping..
<ID:0/034> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
will jtag help ? ( i dont have jtag have to pay if anyone recommends )
anyone can help here please
after flashing samsung logo for 20 seconds it flashes black and white .
hi...
if cant go to recovry mod , flash recovery by odin
then go to recovery and wipe data...
---------- Post added at 06:12 AM ---------- Previous post was at 06:09 AM ----------
and i think pit file can help you... ..
abadan said:
hi...
if cant go to recovry mod , flash recovery by odin
then go to recovery and wipe data...
---------- Post added at 06:12 AM ---------- Previous post was at 06:09 AM ----------
and i think pit file can help you... ..
Click to expand...
Click to collapse
i cant go to recovery and cant flash it. if u have can u post the pit file please .
i tried flashing a p7320 pit and flash file but it gives error . odin log
<ID:0/034> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P7320XXLPI_P7320TLALP2_P7320XXLP7_CL1179571_user_low_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/034> Odin v.3 engine (ID:34)..
<ID:0/034> File analysis..
<ID:0/034> SetupConnection..
<ID:0/034> Initialzation..
<ID:0/034> Set PIT file..
<ID:0/034> DO NOT TURN OFF TARGET!!
<ID:0/034> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
missime said:
i cant go to recovery and cant flash it. if u have can u post the pit file please .
i tried flashing a p7320 pit and flash file but it gives error . odin log
<ID:0/034> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P7320XXLPI_P7320TLALP2_P7320XXLP7_CL1179571_user_low_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/034> Odin v.3 engine (ID:34)..
<ID:0/034> File analysis..
<ID:0/034> SetupConnection..
<ID:0/034> Initialzation..
<ID:0/034> Set PIT file..
<ID:0/034> DO NOT TURN OFF TARGET!!
<ID:0/034> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
if you can go to recovery , then perform a fullwipe
abadan said:
if you can go to recovery , then perform a fullwipe
Click to expand...
Click to collapse
i cant go to recovery bro . that is the problem .
does any here have pit file for this tab . please post here
Your bootloader may be damaged. I used Mobile Tech Videos, mobiletechvideos.com, a $40 JTAG service located in texas. The price included return shipping. Takes about one week.
Sent from my SAMSUNG-SGH-I957 using xda premium
Related
Hello,
While using Sygic navigation dad's galaxy ace (S5830i) got frozen, I restarted it by pushing the power button for a few seconds, but the phone didn't start up, just showing the samsung logo animation again and again... i tried to use recovery mode but it says it "failed to mount /data (invailed agrument).
So I thought i reinstall the original software, that I found on sammobile.com, but while I was installing it, some kind of error happened:
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXLA4_S5830iOXXLA2_RST_S5830iXXLA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl.bin
<ID:0/005> BcmCP.img
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The phone is rooted, all drivers are installed on my pc.
I used more than one versions of Odin, including the version offered by sammobile.com (this is what you can seen on the screenshot)
Im so faithless about the phone now... :crying:
ps: i wasnt able to insert a link because its my first post, so see the screenshot attached.
Hi
valaky said:
Hello,
While using Sygic navigation dad's galaxy ace (S5830i) got frozen, I restarted it by pushing the power button for a few seconds, but the phone didn't start up, just showing the samsung logo animation again and again... i tried to use recovery mode but it says it "failed to mount /data (invailed agrument).
So I thought i reinstall the original software, that I found on sammobile.com, but while I was installing it, some kind of error happened:
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXLA4_S5830iOXXLA2_RST_S5830iXXLA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl.bin
<ID:0/005> BcmCP.img
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The phone is rooted, all drivers are installed on my pc.
I used more than one versions of Odin, including the version offered by sammobile.com (this is what you can seen on the screenshot)
Im so faithless about the phone now... :crying:
ps: i wasnt able to insert a link because its my first post, so see the screenshot attached.
Click to expand...
Click to collapse
Hi there. How's the problem? I also got the same problem, flashing a firmware from sammobile and failing to flash it even if I use the .pit file i found on other threads. But you still have a chance. Download the Pda.tarhere and place it in the PDa section. do not use any pit file. it worked for me, I soft bricked my s5830i several times already and the PDA.tar works like a charm. I got it from here thanks to ickyyy
valaky said:
Hello,
While using Sygic navigation dad's galaxy ace (S5830i) got frozen, I restarted it by pushing the power button for a few seconds, but the phone didn't start up, just showing the samsung logo animation again and again... i tried to use recovery mode but it says it "failed to mount /data (invailed agrument).
So I thought i reinstall the original software, that I found on sammobile.com, but while I was installing it, some kind of error happened:
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXLA4_S5830iOXXLA2_RST_S5830iXXLA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl.bin
<ID:0/005> BcmCP.img
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The phone is rooted, all drivers are installed on my pc.
I used more than one versions of Odin, including the version offered by sammobile.com (this is what you can seen on the screenshot)
Im so faithless about the phone now... :crying:
ps: i wasnt able to insert a link because its my first post, so see the screenshot attached.
Click to expand...
Click to collapse
S5830i only accepts a three file odin installation method. The .PDA file mentioned in the second post is also valid, but its an older firmware for s5830i. Please checkout this thread http://forum.xda-developers.com/showthread.php?t=1822109 to install latest firmware downloaded and made compatible for odin. Details are in the thread. I hope this helps and if it does don't forget the thank button
Dear all,
I found a new firmware on sammobile site and thought to upgrade my Galaxy note from:
N7000JPLPD_N7000OJPLP7_N7000XXLPT_HOME.tar.md5
to:
N7000JPLR8_N7000OJPLR8_N7000XXLRK_HOME.tar.md5
(Both of them for Pakistan)
First I used Odin 1.83 to flash but after about 20% the Odin turned red indicating 'Fail'
Then I searched the web and (I know it's my fault) somewhere downloaded Odin 1.85, checked all the fields on Odin, like "Re Partition- Autoboot-F reset time"
I check them all and then another mistake.... used the same MD5 file in all 3 'PDA, PHONE, CSC" and flashed again.
And also used the PIT file which was in the Odin 1.85's folder.
Now I can enter the download mode but if I try to flash the new ROM, it goes upto 20% and says something like this:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000JPLR8_N7000OJPLR8_N7000XXLRK_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> hidden.img
<ID:0/009> NAND Write Start!!
<ID:0/009> factoryfs.img
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And If I flash the older ROM it says like:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000JPLPD_N7000OJPLP7_N7000XXLPT_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> cache.img
<ID:0/008> NAND Write Start!!
<ID:0/008> factoryfs.img
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help
sulemani1 said:
Dear all,
I found a new firmware on sammobile site and thought to upgrade my Galaxy note from:
N7000JPLPD_N7000OJPLP7_N7000XXLPT_HOME.tar.md5
to:
N7000JPLR8_N7000OJPLR8_N7000XXLRK_HOME.tar.md5
(Both of them for Pakistan)
First I used Odin 1.83 to flash but after about 20% the Odin turned red indicating 'Fail'
Then I searched the web and (I know it's my fault) somewhere downloaded Odin 1.85, checked all the fields on Odin, like "Re Partition- Autoboot-F reset time"
I check them all and then another mistake.... used the same MD5 file in all 3 'PDA, PHONE, CSC" and flashed again.
And also used the PIT file which was in the Odin 1.85's folder.
Now I can enter the download mode but if I try to flash the new ROM, it goes upto 20% and says something like this:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000JPLR8_N7000OJPLR8_N7000XXLRK_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> hidden.img
<ID:0/009> NAND Write Start!!
<ID:0/009> factoryfs.img
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And If I flash the older ROM it says like:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000JPLPD_N7000OJPLP7_N7000XXLPT_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> cache.img
<ID:0/008> NAND Write Start!!
<ID:0/008> factoryfs.img
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help
Click to expand...
Click to collapse
Hi friend just try flashing to GB and then to any other.
Use company cable for data transfer, try with another usb port and i hope it must get cleared.
Press THANKS if it helped you
Thank you my friend, but could you guide me where to find GB? And what GB actually is? The older 2.3.6 Ginger bread?
sulemani1 said:
Thank you my friend, but could you guide me where to find GB? And what GB actually is? The older 2.3.6 Ginger bread?
Click to expand...
Click to collapse
GB actually is the older 2.3.6 Ginger
you find GB in sammobile site
If it's failing at factory.fs then you could be in longer term trouble, let us know.
Sent from my GT-N7000 using xda premium
dude... try this,,
just pull out the battery. wait for 10 secs.. reinsert. go back to download mode.. use odin 1.85 and just select the tar.md5 fine in pda section.. donot check repartion.. dont use pit file.
PS: if odin is stuck once.. u cannot continue from there.. the phone needs a reboot for another try
I read somewhere saying that flashing pit file must be accompanied by bootloader or your device might brick.
Sent from my GT-N7000 using xda premium
nokiamodeln91 said:
dude... try this,,
just pull out the battery. wait for 10 secs.. reinsert. go back to download mode.. use odin 1.85 and just select the tar.md5 fine in pda section.. donot check repartion.. dont use pit file.
PS: if odin is stuck once.. u cannot continue from there.. the phone needs a reboot for another try
Click to expand...
Click to collapse
Thanks friend.
I did it. Im ok now.
Thanks to all of you who helped me here.
Hi ...
my i9070p dead after flash by frimware i9070 , now my phone holding in logo SAMSUNG and i go to Recovery but i can not flash by frimware I9070PAILE1_I9070PAILE1_I9070PTIMLD1_HOME.tar this is a one file PDA
I Thinka flash phone with firmware up into 4 files
plz give me the link to a firmware file 4. Or help come up Mobilee
omidmmm said:
Hi ...
my i9070p dead after flash by frimware i9070 , now my phone holding in logo SAMSUNG and i go to Recovery but i can not flash by frimware I9070PAILE1_I9070PAILE1_I9070PTIMLD1_HOME.tar this is a one file PDA
I Thinka flash phone with firmware up into 4 files
plz give me the link to a firmware file 4. Or help come up Mobilee
Click to expand...
Click to collapse
Did you try flash a firmware for P using odin? (Download mode) Try that.
rodaven said:
Did you try flash a firmware for P using odin? (Download mode) Try that.
Click to expand...
Click to collapse
yes i try but not flashed and This error is
<ID:0/020> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9070PAILE1_I9070PAILE1_I9070PTIMLD1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/020> Odin v.3 engine (ID:20)..
<ID:0/020> File analysis..
<ID:0/020> SetupConnection..
<ID:0/020> Initialzation..
<ID:0/020> Set PIT file..
<ID:0/020> DO NOT TURN OFF TARGET!!
<ID:0/020>
<ID:0/020> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
orrrrrrrrrrrrrrr
<ID:0/020> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9070PAILE1_I9070PAILE1_I9070PTIMLD1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/020> Odin v.3 engine (ID:20)..
<ID:0/020> File analysis..
<ID:0/020> SetupConnection..
<ID:0/020> Initialzation..
<ID:0/020> Get PIT for mapping..
<ID:0/020> Firmware update start..
<ID:0/020> kernel.bin.md5
<ID:0/020> NAND Write Start!!
<ID:0/020> modem.bin.md5
<ID:0/020>
<ID:0/020> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
omidmmm said:
yes i try but not flashed and This error is
<ID:0/020> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9070PAILE1_I9070PAILE1_I9070PTIMLD1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/020> Odin v.3 engine (ID:20)..
<ID:0/020> File analysis..
<ID:0/020> SetupConnection..
<ID:0/020> Initialzation..
<ID:0/020> Set PIT file..
<ID:0/020> DO NOT TURN OFF TARGET!!
<ID:0/020>
<ID:0/020> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
orrrrrrrrrrrrrrr
<ID:0/020> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9070PAILE1_I9070PAILE1_I9070PTIMLD1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/020> Odin v.3 engine (ID:20)..
<ID:0/020> File analysis..
<ID:0/020> SetupConnection..
<ID:0/020> Initialzation..
<ID:0/020> Get PIT for mapping..
<ID:0/020> Firmware update start..
<ID:0/020> kernel.bin.md5
<ID:0/020> NAND Write Start!!
<ID:0/020> modem.bin.md5
<ID:0/020>
<ID:0/020> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
DO NOT TICK 're-partition' ,i will hard bricked ur phone..
u didnt mention from whar version of android before ur phone soft bricked..
try download the latest firmware (xxlpj) for i9070p then flashed it again without repartition ticked..
open odin and leave other untouched. only select pda and select the firmware u've downloaded then click start. wait till the phone boot.
same prob for me
i've flashed a galaxy i9070p with i9070 and its dead now
no power up no download and no recovery mode..... its DEAD
any ideas??
Mrl_onely said:
i've flashed a galaxy i9070p with i9070 and its dead now
no power up no download and no recovery mode..... its DEAD
any ideas??
Click to expand...
Click to collapse
Probably motherboard is dead... Try to get it to service, and see what they will tell you.
In other topic i saw that some user wrote the motherboard replacement costs 100$ or something like that.
Anyway try this guide but do not use the pit file from that thread, skip that step, it worked when i did the same thing with my friends I9100G.
Use any JB firmware for our phone. When going to download mode after removing and reinserting the battery, you should see the yellow triangle.
Hi all. Well, i have a Samsung Galaxy S3 mini (i8200), wich it was given to me to fix it.
I want to clarify that i don't know how did the phone came into this state, i mean, i don't know if the user tried to flash a new rom or what, the thing is that the phone, right now, when i turn ON, it gets stuck on Samsung logo.
I can only enter the download mode.
I can't enter Recovery mode
I've tryed so many things. I've tryed to flash the stock rom (downloaded from Sammobile) with ODIN, but it always shows this error:
<ID:0/026> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I8200XXUAOA2_I8200OXAAOA2_I8200XXUAOA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/026> Odin v.3 engine (ID:26)..
<ID:0/026> File analysis..
<ID:0/026> SetupConnection..
<ID:0/026> Initialzation..
<ID:0/026> Get PIT for mapping..
<ID:0/026> Firmware update start..
<ID:0/026> timh.bin
<ID:0/026> NAND Write Start!!
<ID:0/026> obm.bin
<ID:0/026> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
(I've tryed with differents Odin versions, 3.04, 3.07 , 3.09 , also with different USB ports, and a different PC)
I add a quote i read:
The Problem: Sometimes when you flash a ROM (TouchWiz or AOSP), there is a risk of the /system and /data partitions not wiping correctly thus leading them to be formatted with R/O permissions rather than R/W. This makes it impossible for the phone to boot up because no data can be written. Not even a typical ODIN flash back to stock or rooted stock will fix this. Using CWM to flash another ROM will yield the same no boot results. Furthermore, the stock recovery will not work and it becomes impossible to perform a factory reset. Sound frustrating? It is.
So, i read also, that a pit file its supposed to fix my issue ( this rewrites the PIT tables with the proper permissions).
I get the pit file, and i tried... the results:
<ID:0/026> Added!!
<ID:0/026> Removed!!
<ID:0/026> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I8200XXUAOA2_I8200OXAAOA2_I8200XXUAOA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/026> Odin v.3 engine (ID:26)..
<ID:0/026> File analysis..
<ID:0/026> SetupConnection..
<ID:0/026> Initialzation..
<ID:0/026> Set PIT file..
<ID:0/026> DO NOT TURN OFF TARGET!!
<ID:0/026> Get PIT for mapping..
<ID:0/026> Firmware update start..
<ID:0/026> timh.bin
<ID:0/026> NAND Write Start!!
<ID:0/026> obm.bin
<ID:0/026> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
So, why i keep trying and keep giving an opportunity to this phone?, if im correct, its not a hard brick because i still can enter the Download mode, and in PRODUCT NAME, it still saying GT-I8200 , so, i still have hope.
Im looking for some help, i need help to fix this, im sure im missing something. What can i do?
Thanks in advance.
i have a problem
Sasaoy said:
Hi all. Well, i have a Samsung Galaxy S3 mini (i8200), wich it was given to me to fix it.
I want to clarify that i don't know how did the phone came into this state, i mean, i don't know if the user tried to flash a new rom or what, the thing is that the phone, right now, when i turn ON, it gets stuck on Samsung logo.
I can only enter the download mode.
I can't enter Recovery mode
I've tryed so many things. I've tryed to flash the stock rom (downloaded from Sammobile) with ODIN, but it always shows this error:
<ID:0/026> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I8200XXUAOA2_I8200OXAAOA2_I8200XXUAOA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/026> Odin v.3 engine (ID:26)..
<ID:0/026> File analysis..
<ID:0/026> SetupConnection..
<ID:0/026> Initialzation..
<ID:0/026> Get PIT for mapping..
<ID:0/026> Firmware update start..
<ID:0/026> timh.bin
<ID:0/026> NAND Write Start!!
<ID:0/026> obm.bin
<ID:0/026> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
(I've tryed with differents Odin versions, 3.04, 3.07 , 3.09 , also with different USB ports, and a different PC)
I add a quote i read:
The Problem: Sometimes when you flash a ROM (TouchWiz or AOSP), there is a risk of the /system and /data partitions not wiping correctly thus leading them to be formatted with R/O permissions rather than R/W. This makes it impossible for the phone to boot up because no data can be written. Not even a typical ODIN flash back to stock or rooted stock will fix this. Using CWM to flash another ROM will yield the same no boot results. Furthermore, the stock recovery will not work and it becomes impossible to perform a factory reset. Sound frustrating? It is.
So, i read also, that a pit file its supposed to fix my issue ( this rewrites the PIT tables with the proper permissions).
I get the pit file, and i tried... the results:
<ID:0/026> Added!!
<ID:0/026> Removed!!
<ID:0/026> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I8200XXUAOA2_I8200OXAAOA2_I8200XXUAOA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/026> Odin v.3 engine (ID:26)..
<ID:0/026> File analysis..
<ID:0/026> SetupConnection..
<ID:0/026> Initialzation..
<ID:0/026> Set PIT file..
<ID:0/026> DO NOT TURN OFF TARGET!!
<ID:0/026> Get PIT for mapping..
<ID:0/026> Firmware update start..
<ID:0/026> timh.bin
<ID:0/026> NAND Write Start!!
<ID:0/026> obm.bin
<ID:0/026> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
So, why i keep trying and keep giving an opportunity to this phone?, if im correct, its not a hard brick because i still can enter the Download mode, and in PRODUCT NAME, it still saying GT-I8200 , so, i still have hope.
Im looking for some help, i need help to fix this, im sure im missing something. What can i do?
Thanks in advance.
Click to expand...
Click to collapse
I have the same problem.
I installed several ROM. Finally, I wanted to go back to the Stock ROM and I could not. Error in the memory. Odin stops in the middle of the wash and the phone oběvují different red numbers. He gets into Download Mode, but it does not install it. or I do not get Recavery. I found a tutorial on repairing large S3, but I need my stuff on S3 Mini (GT-I8190). If someone finds something, or would even help it would have been nice. Thank you.
http://forum.xda-developers.com/galaxy-s3/general/samsung-s3-i9300-note2-n7100-i9500-s4-t2647558
Hello,
I had the exact same problem,
messed with R W permissions,
So you should try Heimdall,
I managed to read my PIT file, so it is somehow alive,
but could'nt write a new PIT file on the phone,
I stopped searching and ended buying an old (but working) motherboard for my phone.
But you should really continue, and give it a try.
Hi,
I got myself a Samsung Galaxy SM-T900.
it originally would boot up into GREY battery icon and then apparently switch off although I could see the backlight was dimly on.
( So may have battery or USB charging port problems as well)
It was reporting a custom rom state so I thought I would put it back to stock and actually managed to flash it with Odin 3.10 ( which worked i.e. reported GREEN)
Rom file is T900XXSBPL3_T900OXABOH4_HOME.tar.md5 from Sam Mobile.
Although I got a GREEN light from Odin.... on tablet boot up, the tablet reported " Firmware upgrade encountered an issue...……….in Kies and try again"
Kies (2.6) would not connect to the tablet, nor could I do an emergency firmware recovery as no device comes up in the device list.
So I decided to reflash the stock rom with Odin 3.10 which was a bad move. For some unknown reason it stopped flashing at about halfway.
So I restarted the flash and now always get stuck on
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T900XXSBPL3_T900OXABOH4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin engine v(ID:3.1005)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Get PIT for mapping..
<ID:0/013> Firmware update start..
<ID:0/013> SingleDownload.
<ID:0/013> sboot.bin
<ID:0/013> NAND Write Start!!
<ID:0/013> FAIL!
<ID:0/013>
<ID:0/013> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Could someone please help... I am a casual ROM updater and just follow instructions , but now I am completely stuck.
Thanks
Hi,
Could someone please point me to the PIT file for this SM-T900 UK ROM i.e. BTU
T900XXSBPL3_T900OXABOH4_HOME.tar.md5 from SamMobile for SM-T900
I suspect its in there, but I think I may have corrupted my partitions, so need a PIT file...… I think?
Thanks