I have flushed "RUU_Schubert_HTC_Europe_5.10.401.04_SLSPL_Signed" to downgrade my phone from 5.x and it failed after reaching 100% with this error:
ERROR [270]: UPDATE ERROR
After restarting I can see that it installed Win7 and SPL 1.57 successfully even though it gave me that error earlier.
After this, installation process of RSPL will end successfully on computer, but on mobile it doesn't restart after the process and completely freeze (If I disconnect it from USB it stills show USB instead of Serial, so it frozen) and If I restart it with buttery removal and boot it again, it is still SPL 1.57 and no sign of RSPL. In this step I cant install custom ROMS (Stuck at 0% and error 262) and HSPL (It said that I need to install RSPL first which I cant).
Any I idea? Do I need to install an other ROM before trying custom ROMS? Do I need to try Y cable method? Cuz I dont have a Y cable.
*Edit*: Installing of NoDo and PreNoDo roms also stuck at 0% and end with error 262 when phone is frozen again. Just like custom roms.
http://forum.xda-developers.com/wiki/HTC_HD7/Radios
Nothing? :| No one ever had similar problem?
bump
It was my bad trying to install radio roms instead of shipped roms.
Problem solved by installing "RUU_Schubert_HTC_Europe_1.60.401.01_Radio_5.52.09.16_22.33a.50.10_Signed_SCHUBERT_RELEASE" from following links:
http://forum.xda-developers.com/showthread.php?t=864475
http://forum.xda-developers.com/wiki/HTC_HD7/Shipped_Roms
Related
i was installing WM5 on my wizard when it gave an error at 85% and stopped. only starts in bootloader but wont install a new one. whats the solution?
thanx
Well... we'll need a little more info in order to help. What is your current ipl/spl? What ROM were you trying to upgrade to? Did you get any kind of error message when the RUU stopped?
was 2.24
and i wanted higher so i downloaded one of the O2 roms
ruu gave a "file not good for ur fon" kinda error
Well.... get into bootloader mode (press the voice button while starting the device until you get the three colored screen) and you can flash the original rom again.
Did you CID-unlock your device first? No? Read read read before flashing again. Start at the sticky.
thing is, how do i flash the fon in bootloader mode?
If you connect it to the pc it will say USB at the bottom of your device screen. You can just flash at this point. No need for activesync. If no USB appears on the screen than you're not in bootloader mode.
ruu says no connection cos it always tries to check the current version first.
When I upgrade rom of CHT9110 by P3600i ROM. I got an error Invalid Vendor ID. And screen now is USB Bootloader. How I can restore to the original rom or is there any rom can upgrade for CHT9110 to support English language
up top......................
up up
up up ...............
I confronted same situation as you before. When i tried to flash my 3600i(HK traditional Chinese version) using "RUU_Trinity_DOPODASIA_WWE_3.00.707.17_6275_1.46.00.11_108_Ship.exe" found in forum, my 3600i finished with same error as yours "Invalid Vendor ID" and stayed on 3-color bootloader screen after rebooting. however, It restored to the original rom after I tried to flash my 3600i with upgrading software "D810_GPS_HK_TradChinese.exe" which got from download link appeared on software update in my Htc e-club. flashing "D810_GPS_HK_TradChinese.exe" failed with something like "wrong model" then my 3600i rebooted automatically and restored to the orginal state. I hope my case could do a little help to you.
also found the following from readme.doc in "RUU_Trinity_DOPODASIA_WWE_3.00.707.17_6275_1.46.00.11_108_Ship"
8. Q: I use RUU to update and failed, and my device always boots in three-color mode and cannot enter CE OS anymore, what should I do now?
A: If the update process has failed, you will see that your device will always boot in three-color mode. It’s normal and can be recovered. Please follow the instructions below to reset your device and to establish a connection with the computer.
1. Disconnect your Mobile Device from the USB cradle/cable.
2. Reset your Mobile Device.
3. Reconnect your Mobile Device to the USB cradle/cable.
4. Check that the communication cradle/cable is connected properly.
5. Return to the ROM Update Utility.
Note: You should ignore the ActiveSync connection.
Hi, my htc hd starts with 'smart mobility R1.14.25.24
D1.59.48753' and goes to windows version 6.1 initial screen (preparing for first use), then restarts again. I checked the boot loader screen and it comes with
blac100 32m
spl -1.54.0000
microp-blackstone led v6.
I did try to do USPL v2.5, i get the message 'usb port can not be opened'.Would someone please help to get my phone working? Really appriciate any help.
Hi,
Maybe try to flash with other rom, using SD card.
valanxda said:
Hi, my htc hd starts with 'smart mobility R1.14.25.24
D1.59.48753' and goes to windows version 6.1 initial screen (preparing for first use), then restarts again. I checked the boot loader screen and it comes with
blac100 32m
spl -1.54.0000
microp-blackstone led v6.
I did try to do USPL v2.5, i get the message 'usb port can not be opened'.Would someone please help to get my phone working? Really appriciate any help.
Click to expand...
Click to collapse
Put your phone into its bootloader and try to run USPL.exe. Did you remember to disable antivirus?
Fallen Spartan said:
Put your phone into its bootloader and try to run USPL.exe. Did you remember to disable antivirus?
Click to expand...
Click to collapse
Thanks. I did disable the antivirus. still not working.
Yesterday I tried orange ROM 'OrangeUK_HTCTouchHD_1.59.61.2_Radio_52.64.25.34_1.14.25.24_Ship_phone_software', hoping it would make the phone working. The update was successful, but the same problem.
valanxda said:
Thanks. I did disable the antivirus. still not working.
Yesterday I tried orange ROM 'OrangeUK_HTCTouchHD_1.59.61.2_Radio_52.64.25.34_1.14.25.24_Ship_phone_software', hoping it would make the phone working. The update was successful, but the same problem.
Click to expand...
Click to collapse
Try to install a newer version of the HSPL.
If you can't get USPL to work, have you tried HSPL? Your using a rom based on 1.56+ so you'll need to use HSPL 1.56
I just tried HSPL. I followed the thread http://forum.xda-developers.com/showthread.php?t=505377. Flashing for dummies. When I run the first step 'HSPLWrapper_Blackstone_156OliNex', it sits on 0% for long time and finaly came up with error msg. I tried the option 'recovery', but no use. I have done a hard reset. Still same position where it started. . I'm very sad now..
valanxda said:
I just tried HSPL. I followed the thread http://forum.xda-developers.com/showthread.php?t=505377. Flashing for dummies. When I run the first step 'HSPLWrapper_Blackstone_156OliNex', it sits on 0% for long time and finaly came up with error msg. I tried the option 'recovery', but no use. I have done a hard reset. Still same position where it started. . I'm very sad now..
Click to expand...
Click to collapse
What error message do you get? There should be an error code eg 260 or 262 etc. The different errors have different meanings and different solutions to fix them.
Update error (262). The ROM Update Utility has encountered a communication error during the update process.
I thought I could do the manual option. But hd doesnt go beyond the first windows screen.
valanxda said:
Update error (262). The ROM Update Utility has encountered a communication error during the update process.
I thought I could do the manual option. But hd doesnt go beyond the first windows screen.
Click to expand...
Click to collapse
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
valanxda said:
Update error (262). The ROM Update Utility has encountered a communication error during the update process.
I thought I could do the manual option. But hd doesnt go beyond the first windows screen.
Click to expand...
Click to collapse
Error 262 is a very common error.
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
Click to expand...
Click to collapse
Try to reboot and try to rerun a few times. If this doesn't work you will need to run the manual sspl.
Troubleshooting - manual SSPL
* Boot up your phone.
* Copy SSPL-Manual-TouchHD.exe to your phone. In a file browser on your phone browse to where you copied SSPL-Manual-TouchHD.exe and run it.
* Your phone will reboot into its bootloader and should show SPL v 1.07.OliNex.
* When it shows USB at the bottom then run HSPLWrapper_blackstone_156OilNex.exe from your computer again.
* If bootloader now shows 1.56.olinex you can then flash to your new rom.
Click to expand...
Click to collapse
When you say you tried the manual solution is this what you meant. You may need to reflash to your stock (original) rom first and then run manual sspl from there.
As this is now becoming a flashing problem, please post further responses in the Dummies Guide thread and I'll help you there. This thread will probably be closed soon.
As per post above, please post in dummies guide thread
Thread closed
Phone: HTC Touch Diamond 1
I tried hard reset, soft reset, any kind of reset but nothing. i tried to reflash but it doesn't work, stops at 0%, tried different SPL... any ideas?
eu.florin said:
Phone: HTC Touch Diamond 1
I tried hard reset, soft reset, any kind of reset but nothing. i tried to reflash but it doesn't work, stops at 0%, tried different SPL... any ideas?
Click to expand...
Click to collapse
remove the battery from the device and allow up to 10 minutes
replace the battery and ensure that the device go to bootloader
reflash with an official ROM for your device
Good Luck
thanks for your reply
i removed the battery for a night
the device goes to bootloader, red-green-blue-white has a text:
DIAM100 64M
SPL-1.93.3.000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT 0x32
when I try to flash with an official ROM I receive ERROR [294]: INVALID VENDOR ID
when I try to flash HARD SPL, RADIO or Costum ROM i receive ERROR [262] :UPDATE ERROR
another problem i think is that in flashing process guide I update from Image file NONE to another version like in the picture below
It's there any solution? or my phone needs another motherboard
eu.florin said:
thanks for your reply
i removed the battery for a night
the device goes to bootloader, red-green-blue-white has a text:
DIAM100 64M
SPL-1.93.3.000
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT 0x32
when I try to flash with an official ROM I receive ERROR [294]: INVALID VENDOR ID
when I try to flash HARD SPL, RADIO or Costum ROM i receive ERROR [262] :UPDATE ERROR
another problem i think is that in flashing process guide I update from Image file NONE to another version like in the picture below
It's there any solution? or my phone needs another motherboard
Click to expand...
Click to collapse
What are you using vista or W7 on your computer ??
i tried on xp and win 7
-> ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
-> ERROR [294] : INVALID VENDER ID
One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.
already tried the solutions u gave me in the previous post
thank u for your patience but it seems nothing works
hey eu.florin , try to find the official ROMs on http://www.shipped-roms.com/index.php?category=windows mobile&model = Diamond
Good Luck
thank u Hakim Rahman , I finally found the ROM i need (RUU_Diamond_HTC_WWE_EastEurope_2.03.479.2_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship)
Dear Honorable Seniors, I am so obsessed to get some troubles with my htc (Touch Diamond 2).
I want to get rid off from my ROM that is already available on it (I dont how to find it is official or cooked and which is that version or name). I try to download many cooked ROMs to flash but tried two:
1-energy
2-mozart
but everytime flashing process stopped at 0% percent and after 6-7mint it display a window for recovery. I do restart my system and got the prior windows version, no flashing at all.
I thought there may be Hard-SPL issue (although I dont know what is it). I download its compatible version and try to flash Hard-SPL it also stuck at 0% and not moving upwards.
Help will be appreciated in their respect.
Sorry if my english not comprehendable I am not english speaking person.
regards,
Muqaddas Shahzad
[email protected]
+923222000048
1. Install HSPL. Follow instructions in the thread.
2. Install custom ROM.
You cannot install a ROM until you have installed HSPL first.
I think Muqaddas has already tried HSPL as he described in the post, but the progress stuck @ 0%.
Muqaddas, may be you can try below:
- Disable antivirus software, temporarily, on your PC
- Do HSPL (1.83 and update to 2.51)
- Use Advance ROM Update Utility to do a Task 29.
- Upgrade to latest Radio ROM, if not latest.
- Flash the ROM you wanted.
Hope this will help you .
Thanks.
dear prabhat thank to reply me dear:
1-during Hard spl I found my version is already about 2.16.415.3 and the version I got from Hard-spl link (your given) is showing 1.83.OliNex, yet I tried with this but again stuck at 0% (error code---262)......Can yoy please tell me how Can I check That my cell is already did hard-spl on it-----and how to know it is CID-Unlocked...............
2-by using Advance ROM Update utility, it also not being flashed and giving the same error 0% (code-262)
may this because of my PC operating system which is Windows 7?
but I have flashed HTC Touch Diamond in the same system.....
please help me, my already OS disturbing me alot.
i-windows (send-don't error)
muqaddas_dunyatv said:
please help me, my already OS disturbing me alot.
i-windows (send-don't error)
Click to expand...
Click to collapse
WIN7 could be your issue, it is best to use XP. Also it is important to install the enablenewrapi.cab
You can check your SPL level by entering bootloader mode (holding Volume Down as device reboots until you get to the tri-colored screen)to verify that your SPL: version has "Olinex" as a suffix.
How to flash?
RUU.exe method;
1. Download enablenewrapi.cab, copy to your device with ActiveSync (WMDC) and execute the cab.
2. Download Topaz_CustomRUU_v1.1.zip and both the 1.83 and 2.51 HSPL files.
3. Place the CustomRUU.exe and the RUU_Signed.nbh file from the 1.83 version into the same folder on your PC.
4. With your device sync'd, run the CustomRUU.exe and follow the prompts on your PC.
5. If successful, the progress bar will go to 100% and you can enter bootloader mode (holding Volume Down as device reboots until you get to the tri-colored screen)to verify that your SPL: version has "Olinex" as a sufffix.
If so, you've successfully flashed HSPL.
Repeat steps 3-5 for 2.51
If unsuccessful....
SD Card Method;
1. Rename the RUU_Signed.nbh to TOPAIMG.nbh and place on the root of your FAT32 formatted SD card.
2. Enter bootloader mode and it should initiate the flash. You may get an error of "No Image Found" or you get progress bar stuck at 0%. This would be a failed flash, just soft reset and you'll be back to stock.
If still unsuccessful....
Try the HardSPL_V5_00R5_183HSPL.zip
my respectable serniors please help me out, I tried to change the PC which has Windows XP, and followed all the procedures you all honored but still stock on 0%.....
dear I try to flash PHOTON ROM through storage card by renaming it and placing it into the root of SD card but not being flashed................
please help
HI Muqaddas,
The issue seems to be somewhere in HSPL and the device is not ready for any custom ROM yet. I dont think PC OS has anything to do here unless the "Antivirus S/W is disabled".
Once you device is CID unlocked you should able to install any ROM .
But as you are telling you can see "1.83.OliNex" in the Bootloader... so Can you try to update that to 2.51 and see if that work?
Also try searching the "error code---262" in the HSPL thread, whihc may give you some idea...
EDIT:
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
As you said you can see the OliNex in bootloader your device is CID unlocked.
Can you try below and see if that work:
1) Upgrade your HSPL to 2.51.
2) Start Windows Mobile Device Center
3) Start your device in TriColor boot loader mode.
3) Connect you USB to PC and and make sure your device bootloader white screen say "USB"
4) Now start flashing from PC using RUU.
See if this work else try "SD Card Method" suggested by Bruce.
Hope this will help...
Thanks.
On Ur phone go to Settings-> Connections -> USB to PC & "uncheck" the option Enable faster data synchronization & then try ...worked for me
I am sorry to be desperate but after following all the precedures suggested in this place I am not successful...
I was hopefull that I might flash my TOPAZ after getting 512mb card and after many struggles I arranged it for flashing .....
but after bootloader it stuched at
loading.....
please help if someone can
Try restoring your bootloader to the stock, flash a Windows stock ROM, then come back with HSPL and custom ROM.
Hey, May be you can go to service center near to you and ask them to install new ROM so that they will install new ROM and may be try to unlock the phone if it is with them...
Once they install new ROM then I think you can continue HSPL here and have fun .
Thanks.
Dear Hamsn, Where I can get Windows stock ROM, Please any link or description......
You can get that from HTC website of your region.
Goto: http://www.htc.com/uk/selectcountry.aspx
Select your country -> Click Support -> Select your device and download the latest ROM update.
Of you can grab from here: http://shipped-roms.com/index.php?category=windows mobile&model=Topaz
(File: RUU_Topaz_S2_HTC_WWE_2.53.405.5_Radio_Signed_Topaz_61.44etc.25.35_4.49.25.91_Ship.exe)
Just sync your device in PC and run the above file and all should get updated .
Cheers!!!