[Q] Note 3 N900A Need help with Firmware - AT&T Galaxy Note 3 Q&A, Help & Troubleshooting

Hello, I have a Note 3 AT&T N900A, tried to odin back to stock 4.4.2 but now im stuck at the "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again" Tried kies, its not compatible go figure, also tried flashing http://forum.xda-developers.com/showthread.php?t=2502049 it failed right at the start. Is there anything I can do? Any help is greatly appreciated thank you.

LuckRocks said:
Hello, I have a Note 3 AT&T N900A, tried to odin back to stock 4.4.2 but now im stuck at the "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again" Tried kies, its not compatible go figure, also tried flashing http://forum.xda-developers.com/showthread.php?t=2502049 it failed right at the start. Is there anything I can do? Any help is greatly appreciated thank you.
Click to expand...
Click to collapse
There is no revert back to 4.4.2. What you've linked to is jelly bean. And there is no going back there. What is your issue exactly?

B_I_N_G_E said:
There is no revert back to 4.4.2. What you've linked to is jelly bean. And there is no going back there. What is your issue exactly?
Click to expand...
Click to collapse
Im stuck at the download screen, that's all I can do and as I said it states "Firmware upgrade encountered an issue. Please select recovery mode in kies and try again."

LuckRocks said:
Im stuck at the download screen, that's all I can do and as I said it states "Firmware upgrade encountered an issue. Please select recovery mode in kies and try again."
Click to expand...
Click to collapse
Have you tried either pulling the battery or holding the power button for about 15 seconds to boot back into system? ? Or is there no system to go back to? Which there should be with stock recovery.

B_I_N_G_E said:
Have you tried either pulling the battery or holding the power button for about 15 seconds to boot back into system? ? Or is there no system to go back to? Which there should be with stock recovery.
Click to expand...
Click to collapse
Battery pull shuts off phone then I put it back in and it just goes to download mode. if I hold the power button for 15 seconds it just boots back into download mode. It is stock recovery.

LuckRocks said:
Battery pull shuts off phone then I put it back in and it just goes to download mode. if I hold the power button for 15 seconds it just boots back into download mode. It is stock recovery.
Click to expand...
Click to collapse
Uh oh. This is beyond my comprehension. I don't know how this happened with a stock recovery. Hold tight and someone else should be able to help better than I can. What were you trying to do when this happened?

B_I_N_G_E said:
Uh oh. This is beyond my comprehension. I don't know how this happened with a stock recovery. Hold tight and someone else should be able to help better than I can. What were you trying to do when this happened?
Click to expand...
Click to collapse
Something messed up after I rooted it so I factory reset and it was just sitting at the AT&T boot screen longer than it should of been after doing a reset...kinda sucks because its the only phone I have right now

LuckRocks said:
Something messed up after I rooted it so I factory reset and it was just sitting at the AT&T boot screen longer than it should of been after doing a reset...kinda sucks because its the only phone I have right now
Click to expand...
Click to collapse
All I can think to do is boot into recovery and hit reboot system. Then let it sit. It usually takes mine about 5 mins from there. We can't use odin and without safe strap there is no flashing a replacement rom.
If you can get to att boot screen give it as long as you can to boot

B_I_N_G_E said:
All I can think to do is boot into recovery and hit reboot system. Then let it sit. It usually takes mine about 5 mins from there. We can't use odin and without safe strap there is no flashing a replacement rom.
If you can get to att boot screen give it as long as you can to boot
Click to expand...
Click to collapse
Don't have any of those options, all I have is the download screen. Knox isn't tripped and it still says Official

LuckRocks said:
Don't have any of those options, all I have is the download screen. Knox isn't tripped and it still says Official
Click to expand...
Click to collapse
That's crazy. From a dead phone if you hold volume up home key and power button in that order you can't get to recovery? I don't mean to state the obvious but I don't know how familiar you are. I've had 8 note 3s and I've never been in a spot where I can't get to recovery.

B_I_N_G_E said:
That's crazy. From a dead phone if you hold volume up home key and power button in that order you can't get to recovery? I don't mean to state the obvious but I don't know how familiar you are. I've had 8 note 3s and I've never been in a spot where I can't get to recovery.
Click to expand...
Click to collapse
Just tried it, cant get into recovery only download mode.

LuckRocks said:
Just tried it, cant get into recovery only download mode.
Click to expand...
Click to collapse
Im sorry. I thought I'd take a crack at it. I don't know where to lead you from there. I wish you the best. I've bricked a few phones myself.
I hope you get it resolved. SOMEONE here will be able to help you.

B_I_N_G_E said:
Im sorry. I thought I'd take a crack at it. I don't know where to lead you from there. I wish you the best. I've bricked a few phones myself.
I hope you get it resolved. SOMEONE here will be able to help you.
Click to expand...
Click to collapse
I sent you a PM if you could look at it, it may help.

I'm in the exact same situation and have been trying everything that's been posted but still no success. I'm going to hangout here and see if we can find something that can be done or point us in the right direction. Just letting you know you're not alone on this bud

Hey guys. Check out my post here http://forum.xda-developers.com/showpost.php?p=65467618&postcount=6, read through everything and start at step #4 where you flash the NC2 stock image in the odin AP slot, this should get your phone working again. After that feel free to continue to follow the steps to root, etc. Let me know if this doesn't work and I'll do my best to continue to help.
As long as you can get into download mode, your phone is fine. I've went out of my way testing these to try and permanently brick this phone. I even got it to stop being detected by a computer while in download mode and was still able to recover.
Best of luck

I have a question and I hope someone is still reading through these threads. I have a Galaxy Note 3 AT&T SM-N900A. When I bought it a couple weeks ago, (I already own another one but a T-Mobile variant, to which I've had no issues) I wanted to root it. So I did. Then I removed some system apps. Then I realized I wanted to update it since it was only 4.3! Well OTA was out of the question and so was KIES as I rooted. SO I thought it'd be best to unroot and flash stock firmware and continue to update via OTA. That has not happened. Every time I try to flash stock firmware, regardless of the version of Odin, regardless of where I downloaded the firmware, I always get a fail!!! NOTHING WORKS!!! I even unistalled KIES, reinstalled drivers, tried different USB chords, including the one that came with the phone!!!! I just want to get it back to it's original state so that I can update it via OTA or KIES. I'll paste the ODIN message and a thumbnail that has a screenshot of my phone in download mode when ODIN fails. If ANYONE can help in ANY WAY, I'll donate!!!!! I'll do almost anything!! This is driving me crazy and I'm not one who likes to admit defeat and bring it to Best Buy, especially since Best Buy is over an hour away from here!!! There has to be a way I CAN do this! Here is the ODIN fail message:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900AUCUBMI9_N900AATTBMI9_N900AUCUBMI9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sbl1.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Odin may be failing because the bootloader on the phone may be newer that the bootloader you are flashing.
This might help: http://forum.xda-developers.com/showthread.php?t=2703006

audit13 said:
Odin may be failing because the bootloader on the phone may be newer that the bootloader you are flashing.
This might help: http://forum.xda-developers.com/showthread.php?t=2703006
Click to expand...
Click to collapse
So I need to root it again first, then update it to Lollipop using this guide, correct?

Rooting has nothing to do with installing recovery, boot loader, or ROM.
You are using the wrong file for your phone.

Related

[Q] Please help!! Galaxy s wouldnot turn on!

Hi there
Right now my Samsung Galaxy S wouldn't turn on.
Before this happened, I tried to flash DXJG4 on my device but ODIN got stuck at factoryfs.rfs for ages (more than 10 minutes). So I unpluged the device and took out the batterry. Then i inserted in the battery again and press Volume Down+Home+Power Botton (to get into download mode again). but nothing happens. Cannot even get anything to come up no matter what i press.
Im freaked out right now. Can somebody please help?
Edit : The screen comes back up now after a 30 minute darkness. phew!
Tried to flash again but still stuck at
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> factoryfs.rfs
any idea please?
nothing even comes up when i plug in the charger
Maybe try to download firmware again as well as pit file. Then try to flash it again. Its really hard to brick this phone. Of course I understand that you have usb drivers properly installed and you know well flashing procedure with odin.
Sent from my GT-I9000 using Tapatalk
K0v4L said:
Maybe try to download firmware again as well as pit file. Then try to flash it again. Its really hard to brick this phone.
Sent from my GT-I9000 using Tapatalk
Click to expand...
Click to collapse
thank you for the reply downloading.....
will report as soon as i attempt flashinh rom again!
Running odin as admin and in Xp SP3 compatibility mode worked for me.
jaju123 said:
Running odin as admin and in Xp SP3 compatibility mode worked for me.
Click to expand...
Click to collapse
Didn't work for me . still downloading firmware again.
thank you for the suggestion thou!
rugbycaps said:
nothing even comes up when i plug in the charger
Click to expand...
Click to collapse
wait, so it does not even turn ON at all?
it'll not be possible to flash anything if you can't even mange to turn it on
at the very least in the worse case scenario you should see this fail screen of a bad flash
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
AllGamer said:
wait, so it does not even turn ON at all?
it'll not be possible to flash anything if you can't even mange to turn it on
at the very least in the worse case scenario you should see this fail screen of a bad flash
Click to expand...
Click to collapse
Yup. At first, nothing actually came up at all but thankfully now i can get into download mode for some reason! thank you for your help!
HELP!
AllGamer said:
wait, so it does not even turn ON at all?
it'll not be possible to flash anything if you can't even mange to turn it on
at the very least in the worse case scenario you should see this fail screen of a bad flash
Click to expand...
Click to collapse
My phone shows exactly that picture and won't go into either download or recovery mode... WHAT TO DO???
K0v4L said:
Maybe try to download firmware again as well as pit file. Then try to flash it again. Its really hard to brick this phone. Of course I understand that you have usb drivers properly installed and you know well flashing procedure with odin.
Sent from my GT-I9000 using Tapatalk
Click to expand...
Click to collapse
yes it worked!!! thank you so much!!
Stuck with E:Error in /cache/recovery/sec_csc/zip
(status 7)
Installation aborted.
any idea please???
rugbycaps said:
Stuck with E:Error in /cache/recovery/sec_csc/zip
(status 7)
Installation aborted.
any idea please???
Click to expand...
Click to collapse
you could try going into RECOVERY MODE first,
http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S/Vibrant_GT-I9000M
then select the options to Wipe Cache, then Wipe Data
reboot,
now go back into Download Mode
and try to flash with Odin3 again
and make sure Check the box to REPARTITION
Esbenta said:
My phone shows exactly that picture and won't go into either download or recovery mode... WHAT TO DO???
Click to expand...
Click to collapse
can you go into the download screen?
http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S/Vibrant_GT-I9000M
if you are able to go to that screen, then you can flash with Odin3 again
No, can't go into download or recovery mode
then, you wont be able to do much to fix it.
take it back to the store, tell them your computer rebooted when it was updating.
thank you
Esbenta said:
No, can't go into download or recovery mode
Click to expand...
Click to collapse
I had that problem also (the one from the picture)....
Don't take your phone to the store... =)
Just try this:
- Remove battery+sdcard+power cord+everything you can
- Press AND HOLD the "Volume Down" + "Power Button" combination
- Count to 3 and say "Cú da velha"
- Ask someone to plug in the battery
Welcome to download mode... I hope =)
tell me about it
Hello guys.
I just have one very weird problem with my phone.
Previously, i've been using the asian singapore firmware dxjf4. Today, I decided to flash over to JG5, but didn't like it. So i flashed back to my asian firmware.
What happened is, during the point of flashing, my phone says
E:Error in /cache/recovery/sec_csc.zip
(status 7)
Installation aborted.
Then installation of firmware terminated. Therefore, my phone is still bricked, and I don't know how to revert it back to the asian firmware.
When i flashed the european jg5 firmware, i had to add in the .pit 512, the csc, the pda, and the modem. But for the asian firmware, i only need the pda. So did i flash incorrectly? please help!
Do i need to do a factory data reset before i flash?
Or is there a special way to flash from jg5 to dxjf4?
I wouldn't want another firmware as a solution, because the singapore firmware has specific features and i got certain carrier benefits from the 2 year contract phone line that could enable those specific features.
Thanks.

Unbrick Note from wrong ROM

I accidentally flashed wrong ROM (SII CheckROM) on my Note and now it has stopped booting. IT is stuck on the Galaxy Note N7000 screen and screen starts misbehaving.
I cannot goto CWM recovery all I can still make it to is Stock recovery. How can I Unbrick this state?
Are you able to get into download mode? (Power off, then power on holding VolumeDown + Menu + Power all together until the screen comes on?)
Then you'll be able to flash a rom via Odin...
if you can get into download mode, which is what i assume you mean by stoke recovery you can flash the rom using odin on the pc
Inf3rn0.nl said:
Are you able to get into download mode? (Power off, then power on holding VolumeDown + Menu + Power all together until the screen comes on?)
Then you'll be able to flash a rom via Odin...
Click to expand...
Click to collapse
Yes, I can. What options shall I check in Odin?
Re-partition
F. Reset time
Flash lock
Phone EFS clear
Phone bootloader update
taranfx said:
Yes, I can. What options shall I check in Odin?
Re-partition
F. Reset time
Flash lock
Phone EFS clear
Phone bootloader update
Click to expand...
Click to collapse
Just select ' n7000 stock rom n installation' from my signature. Read post number 2 n 3 . You will find your answer
Sent from my GT-N7000 using xda premium
hi..
help me with my problem..
i can't go to download mode and recovery mode..
it's just blank screen like totally dead,,
thanks
please search for "usb jig" either in google or here in the forum.
underdoux said:
hi..
help me with my problem..
i can't go to download mode and recovery mode..
it's just blank screen like totally dead,,
thanks
Click to expand...
Click to collapse
You will need to use the USB_jig
Sent from my GT-N7000 using xda premium
I have the same problem, I accidentally flashed a galaxy s2 kernel, and my screen misbehaves after logo. Now, I can't get into download mode since it says low battery. I've been trying to charge it with wall charger, even though back cover gets warmer, it still says low battery. I've purchased an Anker universal charger, left the battery overnight, nope still no luck, should I buy a new battery ?
Bricked Galaxy Note N7000 or Incorrect ROM Flash Easy Fix
Ok simple you won't see nothing on the screen because the bootloader is wrong.....
Just put the battery in then do following.
1. hold vol down+home+power for 15 seconds...
2. release then press volume up...
Note: Don't worry about seeing anything on the screen or any keys light
it will be blank this is because bootloader is incorrect
3. open odin you should see comxx in listed flash the original bootloader back
into phone this will/should resume visual display.
I have attached necessary files to resume
Load File in PDA NOT BOOTLOODER
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4. Wait 10 seconds.. Remove Battery Then Boot Back into Bootloader following steps 1&2
5. finally flash Stock Rom to resume the whole phone to original state.
Hope That Helps......
Sent from my GT-N7000 using Tapatalk
I can get into download mode now, however I don't know which Stock Rom I should download since I forgot which was it. Is there any way I learn it without trying and failing among many available
antiguangenius said:
Ok simple you won't see nothing on the screen because the bootloader is wrong.....
Just put the battery in then do following.
1. hold vol down+home+power for 15 seconds...
2. release then press volume up...
Note: Don't worry about seeing anything on the screen or any keys light
it will be blank this is because bootloader is incorrect
3. open odin you should see comxx in listed flash the original bootloader back
into phone this will/should resume visual display.
I have attached necessary files to resume
Load File in PDA NOT BOOTLOODER
4. Wait 10 seconds.. Remove Battery Then Boot Back into Bootloader following steps 1&2
5. finally flash Stock Rom to resume the whole phone to original state.
Hope That Helps......
Sent from my GT-N7000 using Tapatalk
Click to expand...
Click to collapse
thanks for this! but, I don't have acces to "imaginary" donwload mode.. my note is bricked 100%. My computer does not recognize anything at all
antiguangenius said:
Ok simple you won't see nothing on the screen because the bootloader is wrong.....
Click to expand...
Click to collapse
Thank you so much for your step-by-step guides.
Just un-bricked (or un-soft-bricked?) my Note. Couldn't be happier :-D
Nice one
eliot_11 said:
thanks for this! but, I don't have acces to "imaginary" donwload mode.. my note is bricked 100%. My computer does not recognize anything at all
Click to expand...
Click to collapse
is the battery charged??? its not bricked.... once the flash has power it can be fixed..... just have some patience....
hey how did you go about doing this. Please help. I accidentally put a n7000 rom in my att galaxy note i717. Now I can't get the screen to turn on either.
---------- Post added at 09:35 AM ---------- Previous post was at 09:25 AM ----------
prmcmanus said:
Thank you so much for your step-by-step guides.
Just un-bricked (or un-soft-bricked?) my Note. Couldn't be happier :-D
Nice one
Click to expand...
Click to collapse
hey how did you go about doing this. Please help. I accidentally put a n7000 rom in my att galaxy note i717. Now I can't get the screen to turn on either.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Rooted_Stock_Odex_N7000XXLC1.tar.md5 is valid.
<OSM> MODEM_N7000XXLB2_REV_05_CL1106002.tar.md5 is valid.
<OSM> GT-N7000-MULTI-CSC-OXALC1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.img
<ID:0/003> NAND Write Start!
stuck =/
Killed my Note
<ID:0/030> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKL3_N7000ODDKL1_N7000DDKL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/030> Odin v.3 engine (ID:30)..
<ID:0/030> File analysis..
<ID:0/030> SetupConnection..
<ID:0/030> Initialzation..
<ID:0/030> Get PIT for mapping..
<ID:0/030> Firmware update start..
<ID:0/030> boot.bin
<ID:0/030> NAND Write Start!!
<ID:0/030> cache.img
<ID:0/030> factoryfs.img
//Stuck
Tried going from ICS from Germany to stock but stuck??
Any help appreciated..
Lol how do u accidently download the wrong rom from the other version ????? If u have a i717 then don't go to the n7000 threads lol sheesh
Sent from my SAMSUNG-SGH-I717 using Tapatalk 2
odd note
hello all,
my case was a bit different, after the ics leak, i rooted and flashed rocketrom without problems, then i flashed kriskelo also without problems but wanted to go back to rocketrom, the problem is that the device got stucked in the galaxy note gt 7000 screen with the rooted triangle after i tried to recover rocketrom via cwm, i have back ups from all the roms, lcy, rocket and kriskelo except from the GB but the phone doesnt boot, i tried odin but it get stucked in the "network connecting" and it doesnt go far...im downloading now the stock gb and will try the antiguangenius way, just a small question, do i have to flash only the bootloader (file attached in the post} and then the stock rom or just the stockrom directly in the pda? what is the nt7000 bootloader file?
extra info, my phone enters in cwm recovery without problems, and if i connect the usb on it with the galaxy note gt7000 screen, i get the yellow flag ( i assume is the download mode, isnt it?) so its not completely bricked, i see all the menu from cwm and can also recover, but it wont boot anybody could help? im afraid how much it would be bringing it to the SSC...
thanks in advance
Dtorga
Sorry with all due respect, how can one accidentally flash a SII rom onto a N7000 or a N7000 rom onto a I717? Do you people think we all are stupid because we don't flash roms that were built for other devices onto our Notes? Why don't people think before they flash? I mean it's known that men cannot think clearly when they see a naked women with big b.... but I did not know that this effect also takes place when they see a phone and a rom
Sent from my Galaxy Note running ICS

[Q] Need help rooting GB_2.3.5 SGS_Captivate_I897 Att

Ok I'm not sure if I am posting in the right area I've read a fewpostings and couldn't find if I was doing this correctly but I cannot post images but I can send them to you I am stuck on Odin. I had it rooted before and updated using kies mini then found that I needed to re-root :/
<ID:0/006> Added!!
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
^^this is what I see on odin and IDK if I'm done with odin and should reboot or what??
H4MM3R311 said:
Ok I'm not sure if I am posting in the right area I've read a fewpostings and couldn't find if I was doing this correctly but I cannot post images but I can send them to you I am stuck on Odin. I had it rooted before and updated using kies mini then found that I needed to re-root :/
<ID:0/006> Added!!
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
^^this is what I see on odin and IDK if I'm done with odin and should reboot or what??
Click to expand...
Click to collapse
Sounds like a connection issue. Look >>HERE<< for tips on correcting them.
Thanks
mrhaley30705 said:
Sounds like a connection issue. Look >>HERE<< for tips on correcting them.
Click to expand...
Click to collapse
Ok I have the /!\ android digging and now I have this message says most can root but not all I got this message this time.
<OSM> All threads completed. (succeed 0 /failed 1)
<ID:0/006> Removed!!
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
any idea whats up?
odin sometimes locks up..
what version odin are you using? 1.0 sucks balls use this one... Odin3v1.85.zip
also why are you using odin to root? [APP]SuperOneClick v2.3.3
TRusselo said:
odin sometimes locks up..
what version odin are you using? 1.0 sucks balls use this one... Odin3v1.85.zip
also why are you using odin to root? [APP]SuperOneClick v2.3.3
Click to expand...
Click to collapse
I will test one click out thanks I was using an old version of odin because some goof said that oneclick does not work on gingerbread and that odin would work :/ I used it the last time I rooted on froyo.
-_- now IDK what happened I properly disconnected my phone and now it shoes a cell phone Icon.../!\...PCIcon on a black screen.
I feel like the more I mess with it the more I screw it up, now it wont leave that screen (I was in Download mode)
that is the soft brick screen. and its properly written " Phone /!\ PC " (you can underline the /!\ if you want to be fancy)
use it as download mode. if odin doesnt see it, reboot the phone again, reboot your PC, then try again.
TRusselo said:
that is the soft brick screen. and its properly written " Phone /!\ PC " (you can underline the /!\ if you want to be fancy)
use it as download mode. if odin doesnt see it, reboot the phone again, reboot your PC, then try again.
Click to expand...
Click to collapse
It wont let me reboot but I will attempt to use odin.
Ok my phone now doesn't even boot...
Please help, I don't know what to do and I need my phone :/ I backed up everything except root files.
OK phone booted to Downloading screen.
Well when anyone gets back online can I be directed to somewhere where I can get directions on how to return my phone to stock SGS captivate i897 thank you all for your help.
I'd start here:
http://forum.xda-developers.com/showthread.php?t=1300843
where you can find a ton of one-clicks to get back to stock.
If you look at post 3 here:
http://forum.xda-developers.com/showpost.php?p=18370912&postcount=3
you can find the Odin and Heimdall one-clicks to get to stock 2.3.5 KK4.
After that try this thread to obtain root:
http://forum.xda-developers.com/showthread.php?t=1444382
That's what I did last time and it worked well. I went on to try the Corn Kernel and liked that as well. In the end I came back to CM7, though. It just gives my phone life that stock can't accomplish.
Good luck!
As with anything, be sure to read read read. This is what worked for me and you never know when that could be a fluke.
Nick D said:
I'd start here:
http://forum.xda-developers.com/showthread.php?t=1300843
where you can find a ton of one-clicks to get back to stock.
If you look at post 3 here:
http://forum.xda-developers.com/showpost.php?p=18370912&postcount=3
you can find the Odin and Heimdall one-clicks to get to stock 2.3.5 KK4.
After that try this thread to obtain root:
http://forum.xda-developers.com/showthread.php?t=1444382
That's what I did last time and it worked well. I went on to try the Corn Kernel and liked that as well. In the end I came back to CM7, though. It just gives my phone life that stock can't accomplish.
Good luck!
As with anything, be sure to read read read. This is what worked for me and you never know when that could be a fluke.
Click to expand...
Click to collapse
Wonderful, I am attempting that now my phone is in download mode just waiting to finish downloading i897uckk4 contains bootloaders
OK not sure if bootloaders was necessary but it worked like a charm, my mistake before was using a crappy version of Odin and for the wrong reason.
I stayed up reading all night last night till 4am on this site trying to figure it out but I had Odin all along just didnt know how to run it
Now I would like to flash to something else and would definitely appreciate it if you wouldn't you mind sending me some links in a PM to a thread with directions on how to get CM7? if not its ok you've done a hell of a-lot for me already thanks so much.
Thanks to Nick D for leading me to the right place and TRusello for helping me get my phone back to DL mode.
Tried rooting with super one click, TRusselo suggested and the program stopped responding, My phone is still plugged in and I'm not sure if I want to unplug or what.
any suggestions?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
H4MM3R311 said:
Tried rooting with super one click, TRusselo suggested and the program stopped responding, My phone is still plugged in and I'm not sure if I want to unplug or what.
any suggestions?
Click to expand...
Click to collapse
Super One Click has not worked to root 2.3. Always gets stuck at step 7, just like you show there. As far as I know you just abandon it. Nothing has been done to your phone.
To get root you will have to odin a kernel that either has root or you can use to root.
I used Mtcarey's Corn kernel. V7.06. It has CWM as well. In the recovery menu that comes with the kernel is an option to root your phone. I used Vz 1.85 of Odin and had not problems. It was very easy.
0. Download the latest Corn kernel vz 7.06 from http://forum.xda-developers.com/showthread.php?t=1294477. Note, earlier versions will work as well.
1. Start Odin on your PC.
2. Put your phone into download by holding the volume up and volume down buttons. The little android guy with a shovel shows up.
3. Plug in your phone. Odin will show that it has detected the phone. The reboot option should be already checked.
4. Put the zip file you downloaded to your pc in the PDA slot by pushing the PDA button and then searching and selecting the file.
5. Flash. When it is done your phone will reboot.
6. Have an adult beverage.
There have been reports of that kernel having issues with EXT4 however so I left all of that and other speed tweaks alone.
KMan94 said:
Super One Click has not worked to root 2.3. Always gets stuck at step 7, just like you show there. As far as I know you just abandon it. Nothing has been done to your phone.
To get root you will have to odin a kernel that either has root or you can use to root.
I used Mtcarey's Corn kernel. V7.06. It has CWM as well. In the recovery menu that comes with the kernel is an option to root your phone. I used Vz 1.85 of Odin and had not problems. It was very easy.
0. Download the latest Corn kernel vz 7.06 from http://forum.xda-developers.com/showthread.php?t=1294477. Note, earlier versions will work as well.
1. Start Odin on your PC.
2. Put your phone into download by holding the volume up and volume down buttons. The little android guy with a shovel shows up.
3. Plug in your phone. Odin will show that it has detected the phone. The reboot option should be already checked.
4. Put the zip file you downloaded to your pc in the PDA slot by pushing the PDA button and then searching and selecting the file.
5. Flash. When it is done your phone will reboot.
6. Have an adult beverage.
There have been reports of that kernel having issues with EXT4 however so I left all of that and other speed tweaks alone.
Click to expand...
Click to collapse
Is that it!? Slaps self in forehead, I was so confused reading off of other peoples directions that I thought it would be too complicated for me... wow your directions were perfect! I will have two Blue Moons one for myself and one for you but since you are not near... I will drink it for you LOL! Thank you so much!!!
After following all the steps and succeeding the apps like super user and titanium backup still say that my phone is not rooted.
OK I feel like a dumb ass but IDK how to get to "In the recovery menu that comes with the kernel is an option to root your phone"
OK got into recovery mode but I see no option to root phone....
so I kept searching within the menus in recovery and found it Thanks again.
H4MM3R311 said:
Wonderful, I am attempting that now my phone is in download mode just waiting to finish downloading i897uckk4 contains bootloaders
OK not sure if bootloaders was necessary but it worked like a charm, my mistake before was using a crappy version of Odin and for the wrong reason.
I stayed up reading all night last night till 4am on this site trying to figure it out but I had Odin all along just didnt know how to run it
Now I would like to flash to something else and would definitely appreciate it if you wouldn't you mind sending me some links in a PM to a thread with directions on how to get CM7? if not its ok you've done a hell of a-lot for me already thanks so much.
Thanks to Nick D for leading me to the right place and TRusello for helping me get my phone back to DL mode.
Click to expand...
Click to collapse
I happened to see this reply at the same time I was surfing Cyanogen's site, so it's your lucky day for links:
Here is the stable version of CM7 for Captivate:
http://download.cyanogenmod.com/?type=stable&device=captivatemtd
Here's the instructions for how:
http://wiki.cyanogenmod.com/wiki/Samsung_Captivate:_Full_Update_Guide
The guide says you have to be on Android 2.2 bootloaders to jump to CM7. Numerous users have stated that's not the case, it's just Cyanogen covering their ass. I don't blame them, but you can read on the matter and make your own decision. I don't think I've yet read of someone jumping from 2.3.x to CM7 and having issues over bootloaders.
Edit: Just saw that you already flashed Corn and got CWM. You're well on the way now.
Nick D said:
I happened to see this reply at the same time I was surfing Cyanogen's site, so it's your lucky day for links:
Here is the stable version of CM7 for Captivate:
http://download.cyanogenmod.com/?type=stable&device=captivatemtd
Here's the instructions for how:
http://wiki.cyanogenmod.com/wiki/Samsung_Captivate:_Full_Update_Guide
The guide says you have to be on Android 2.2 bootloaders to jump to CM7. Numerous users have stated that's not the case, it's just Cyanogen covering their ass. I don't blame them, but you can read on the matter and make your own decision. I don't think I've yet read of someone jumping from 2.3.x to CM7 and having issues over bootloaders.
Edit: Just saw that you already flashed Corn and got CWM. You're well on the way now.
Click to expand...
Click to collapse
Wow, wonderful your the man Nick. Funny thing I have a best friend named Nick D. and one of my Fav UFC guys is named Nick D. LOL thanks so much dude you save me alot of headache and reading time.

[Q] Galaxy S Advance Stuck on boot screen

My Samsung Galaxy S Advance phone is not restarting. It gets stuck on boot screen.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I was having an error: Vodafone service error: 0x5 so I tried to restart my phone, but it never did.
I tried to wipe cache using recovery mode (by hard reset key combination) by it never completed (i waited for about 30-40 minutes).
Then i tried to wipe data but it did not complete. I am waiting for past 1 hour( I dont this is normal).
I had upgraded my phone to Jelly Bean few months back using the updates from samsung and it did succeed in first attempt.
Also I have not changed/updated any other settings on my phone.
Please help me out.
Thanks.
alikanch7 said:
My Samsung Galaxy S Advance phone is not restarting. It gets stuck on boot screen.
View attachment 2411633
I was having an error: Vodafone service error: 0x5 so I tried to restart my phone, but it never did.
I tried to wipe cache using recovery mode (by hard reset key combination) by it never completed (i waited for about 30-40 minutes).
Then i tried to wipe data but it did not complete. I am waiting for past 1 hour( I dont this is normal).
I had upgraded my phone to Jelly Bean few months back using the updates from samsung and it did succeed in first attempt.
Also I have not changed/updated any other settings on my phone.
Please help me out.
Thanks.
Click to expand...
Click to collapse
1.Goto download mode ( power+home+vol.down)
2.flash stock JB again using odin.
Phone is now not responding at all
harith.unnikrishnan said:
1.Goto download mode ( power+home+vol.down)
2.flash stock JB again using odin.
Click to expand...
Click to collapse
Thanks for the reply but I can't do it. The phone has now stopped responding completely.
It gives no response on pressing these key combinations. Though I have tried these combinations in the morning and were working fine.
I think I'll give it a night and try these again in morning.
alikanch7 said:
Thanks for the reply but I can't do it. The phone has now stopped responding completely.
It gives no response on pressing these key combinations. Though I have tried these combinations in the morning and were working fine.
I think I'll give it a night and try these again in morning.
Click to expand...
Click to collapse
Pull out battery, put it back in and hold those keys untill you feel short vibration.
Sent from my GT-I9070 using Tapatalk
Where to find the Stock JB
harith.unnikrishnan said:
1.Goto download mode ( power+home+vol.down)
2.flash stock JB again using odin.
Click to expand...
Click to collapse
where can i find this stock JB??
I have downloaded the relevant Indian version from this site live.samsung-updates.com/index.php?device=GT-I9070
will this suffice?? or do i need to download another.
Also slightly elaborate the procedure.
Thanks.
alikanch7 said:
where can i find this stock JB??
I have downloaded the relevant Indian version from this site live.samsung-updates.com/index.php?device=GT-I9070
will this suffice?? or do i need to download another.
Also slightly elaborate the procedure.
Thanks.
Click to expand...
Click to collapse
http://live.samsung-updates.com/details/9033/Galaxy_S_Advance/GT-I9070/INU/I9070DDULP8.html
Before download mode and reflash with Odin, recharge the phone!!!
Did you wipe dalvik cache? You probably already did.
How to clear dalvin cache?
wietje91 said:
Did you wipe dalvik cache? You probably already did.
Click to expand...
Click to collapse
No I did not.
I did try to wipe data but it did not succeed. It gets stuck on formatting /data and then nothing happens (i left it as it is for about an hour and I guess it should not take that much time).
I also did try to wipe cache but then the phone doesnt respond.
Also last night I did flashed it using ODIN. It was successful but the problem still remains same.
Can you explain the Dalvik Cache procedure a little more?
Even flashing did not work
mathei said:
live.samsung-updates.com/details/9033/Galaxy_S_Advance/GT-I9070/INU/I9070DDULP8.html
Before download mode and reflash with Odin, recharge the phone!!!
Click to expand...
Click to collapse
harith.unnikrishnan said:
1.Goto download mode ( power+home+vol.down)
2.flash stock JB again using odin.
Click to expand...
Click to collapse
I did try as suggested, Downloaded the stock rom then ODIN and then followed the procedure and did get a PASS! in ODIN.
But unfortunately, the phone is still same. no improvement.
I m attaching the ODIN snap and log.
Odin Log:
<ID:0/042> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9070DDULP8_I9070ODDULP8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/042> Odin v.3 engine (ID:42)..
<ID:0/042> File analysis..
<ID:0/042> SetupConnection..
<ID:0/042> Initialzation..
<ID:0/042> Get PIT for mapping..
<ID:0/042> Firmware update start..
<ID:0/042> cache.img.md5
<ID:0/042> NAND Write Start!!
<ID:0/042> hidden.img.md5
<ID:0/042> kernel2.bin.md5
<ID:0/042> kernel.bin.md5
<ID:0/042> modem.bin.md5
<ID:0/042> normal.bin.md5
<ID:0/042> param.lfs.md5
<ID:0/042> power_management.bin.md5
<ID:0/042> system.img.md5
<ID:0/042> RQT_CLOSE !!
<ID:0/042> RES OK !!
<ID:0/042> Removed!!
<ID:0/042> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Somebody just help me
No response?
Is there no other solution or no one cares to provide me with one?
Is there anything else left that can be done or should I consult the Samsung Service Center.
alikanch7 said:
No response?
Is there no other solution or no one cares to provide me with one?
Is there anything else left that can be done or should I consult the Samsung Service Center.
Click to expand...
Click to collapse
What cause problem in first place? What did you do before you got that stuck on logo screen?
alikanch7 said:
No response?
Is there no other solution or no one cares to provide me with one?
Is there anything else left that can be done or should I consult the Samsung Service Center.
Click to expand...
Click to collapse
After you flash the firmware with Odin, you tried to get into recovery? Remove the battery, put it back, simultaneously press the three buttons (volume up, menu and power). If you get into recovery, you have to touch factory reset and restart.
Try a reflash with Odin ...
If it still does not work, service Samsung is recommended ...
alikanch7 said:
No response?
Is there no other solution or no one cares to provide me with one?
Is there anything else left that can be done or should I consult the Samsung Service Center.
Click to expand...
Click to collapse
Ok this is really weird :S. I don't have the knowledge to solve this. Let's hope someone else responds to
shut_down said:
What cause problem in first place? What did you do before you got that stuck on logo screen?
Click to expand...
Click to collapse
Absolutely Nothing that I should not...
I just turned off the phone using power button and selecting Power Off. Just to turn it off again (that too for some stupid sort of vodafone services error: 0x05).
But the phone did never turned on again.
mathei said:
...
If it still does not work, service Samsung is recommended ...
Click to expand...
Click to collapse
alikanch7 said:
Absolutely Nothing that I should not...
...But the phone did never turned on again.
Click to expand...
Click to collapse
Go to service, like mathei said.
mathei said:
After you flash the firmware with Odin, you tried to get into recovery? Remove the battery, put it back, simultaneously press the three buttons (volume up, menu and power). If you get into recovery, you have to touch factory reset and restart.
Try a reflash with Odin ...
If it still does not work, service Samsung is recommended ...
Click to expand...
Click to collapse
I did factory reset but it didn't work. same as earlier it just stops responding.
Samsung people say my motherboard is gone. need to be replaced. But I dont believe them, dont know why but I have a gut feeling that the motherboard is fine as the ODIN flash procedure went very smoothly, unsuccessful though... also phone is still responding during recovery procedure, though not completing the procedure correctly.
Also, I just dont wanna believe my phone is dead.
alikanch7 said:
I did factory reset but it didn't work. same as earlier it just stops responding.
Samsung people say my motherboard is gone. need to be replaced. But I dont believe them, dont know why but I have a gut feeling that the motherboard is fine as the ODIN flash procedure went very smoothly, unsuccessful though... also phone is still responding during recovery procedure, though not completing the procedure correctly.
Also, I just dont wanna believe my phone is dead.
Click to expand...
Click to collapse
Then take it to some other service, and see what they will say. You have unofficial service there (non Samsung)?
But that what is happening in Odin telling you that they are not lying you.
shut_down said:
Then take it to some other service, and see what they will say. You have unofficial service there (non Samsung)?
But that what is happening in Odin telling you that they are not lying you.
Click to expand...
Click to collapse
Yeah we do have the unofficial service centers here. I am surely gonna give it a try as I have nothing more to lose...
I dont know how a standard procedure for turning off your phone can do this lot of damage...
can anyone plzz tell me how to flash JB firmware using fastboot in sgsa... and where can i get the firmware image files for fastboot...!! plzz help i am stuck in the boot screen and i have tried everthing including facory reset and odin doesnt work with me... so only option is fastboot
alikanch7 said:
Yeah we do have the unofficial service centers here. I am surely gonna give it a try as I have nothing more to lose...
I dont know how a standard procedure for turning off your phone can do this lot of damage...
Click to expand...
Click to collapse
try downgrading to GB

Help with brick please

Hey all,
As per title, A while back I rooted and installed a few custom roms on my unit before sticking with one named
"GT-7000_SweetROM_V11.1_LTA" and all was going well until a "super user" app update and a "low battery" met in the middle and my phone lost power and turned off.
Now my phone will not boot and freezes on the samsung logo, pressing vol up + power + home will, not bring up the recovery mode
but vol down + power + home will take me to a download screen, Odin, if my research is right.
I've read a few posts with the same symptoms as me but with different reasons for getting there in the first place and I'm unsure of what to do.
If my reading has been correct I'm not hard bricked but am in a bit of a spot and PC Odin can help me out, but then there are different versions of Odin as well.
Just some more bits and peices that I can think of to try and give you all as much info as possible. here goes,
I do remember Philz ???? something on my phone and was able to switch between roms by placing them on the external micro sd card and using vol up + power + home to navigate a menu.
Whilst writing this post I have had my unit plugged in via usb and it justs sits there with the battery icon showing but it shows no movement ie: the little cirle will not spin nor will the green charge level go up. Also it tried to install "mobi" something onto my pc.
Another problem I'm having is finding a valid download link for PC Odin any help there would be cool.
If you need anymore info I'll do my best but I'm very new to this, many thanks
E2A: have downloaded Odin and phone is reconized there just need to learn how to use the Prog
Download and flash PhilZ kernel 15.5 odin version. Flask on via odin (put it in pda tab and flash) and see if you can get your phone working again or can get into recovery. If not download and.flash whole stock jb rom. There is also a ltc rom odin version recently posted in one of the two dev threads.
As how to use odin for note, find the famous sticky thread by dr.ketan in our n7000 forum.
Sent from my GT-N7000 using Tapatalk 2
@rinksy55 you said low battery right? charge the battery first and then try to go to recovery and download mode.
forest1971 said:
Download and flash PhilZ kernel 15.5 odin version. Flask on via odin (put it in pda tab and flash) and see if you can get your phone working again or can get into recovery. If not download and.flash whole stock jb rom. There is also a ltc rom odin version recently posted in one of the two dev threads.
As how to use odin for note, find the famous sticky thread by dr.ketan in our n7000 forum.
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
thanks for the reply
I tried to flash "philz_touch_6.07.9-n7000.tar.md5" with Odin3 V1.87 and it failed
also tried "N7000XXLTC_MOD1.tar.md5" which also failed
treacherous_hawk said:
@rinksy55 you said low battery right? charge the battery first and then try to go to recovery and download mode.
Click to expand...
Click to collapse
Yeah low battery which doesnt seem to be charging acording to the widget but I can enter download mode whilst plugged in to usb but not recovery
just for info my phone acts the same wether plugged into comp or the wall socket with samsung hardware
guess Im screwed eh?
thanks
I would try a new battery.
Sent from my GT-N7000 using Tapatalk 2
I'm sure the battery is fine it's the phone thats mucked up, I've not had any problems to idicate my battery was failing
Are there any other avenues I could explore? I'm willing to get a new battery but then I could have 1 phone and 2 dead batteries and no way of charging.
When I tried flashing PhilZ kernel and the jb rom with Odin it was Odin that did its thing then reported to have failed, the phone had power to it the whole time and was showing the download screen with the message "do not turn off target".
thanks for you help so far
E2A Image
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Looks like problem with setting up connection. Drivers/USB/USB Cable/Ports/PC.
nokiamodeln91 said:
Looks like problem with setting up connection. Drivers/USB/USB Cable/Ports/PC.
Click to expand...
Click to collapse
Thanks for helping out :good:
Drivers are up to date, installed kies then uninstalled leaving the drivers behind.
USB, have used all the ports on my pc
Changed cable, used the wife's S3 cable
Ports, I can open ports easy, thought that was just router tho
PC, not sure what you mean there but running Win7 with decent spec.
Still the same outcome, fails on connection
thanks for taking the time tho
Try installing one from here
http://forum.xda-developers.com/showthread.php?p=49864289
nokiamodeln91 said:
Try installing one from here
http://forum.xda-developers.com/showthread.php?p=49864289
Click to expand...
Click to collapse
I saw that link earlier and tried 'PhilZ-cwm6-ZSLR1-OZS-5.11.2.tar.md5' and after reading your last post went back and tried 'PhilZ-cwm6-ZSLR1-OZS-5.11.2.tar.md5'
dont think its the rom heres the text from odin:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PhilZ-cwm6-DDLSC-ODD-5.11.2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
seems to be hanging on a connection
1. Install the latest drivers from: http://forum.xda-developers.com/showthread.php?t=961956/
2. Reboot
3. Disable all antiviruses
4. On your phone:
a) Boot into download mode
b) Plug your phone into your PC (only plug it into the USB 2.0 ports, don't do it on 3.0 or 1.1 or 1.0 etc.)
c) Follow the on screen instructions saying something along the lines of "Press volume up to continue" - you want to continue
d) Check whether Odin has detected your phone, if it has continue to step 5
5. Flash a stock ROM or kernel
6. If it succeeds, boot into recovery and perform a factory reset <= ONLY IF IT ISN"T ICS
OK.. Odin is not able to get to the PIT mappings.. There seems to be some connection issues. Check with newer version of Odin.. Also probably a different pc.
---------- Post added at 04:55 AM ---------- Previous post was at 04:52 AM ----------
Uninstall moboginie drivers as well completely.
XxPixX said:
1. Install the latest drivers from: http://forum.xda-developers.com/showthread.php?t=961956/
2. Reboot
3. Disable all antiviruses
4. On your phone:
a) Boot into download mode
b) Plug your phone into your PC (only plug it into the USB 2.0 ports, don't do it on 3.0 or 1.1 or 1.0 etc.)
c) Follow the on screen instructions saying something along the lines of "Press volume up to continue" - you want to continue
d) Check whether Odin has detected your phone, if it has continue to step 5
5. Flash a stock ROM or kernel
6. If it succeeds, boot into recovery and perform a factory reset <= ONLY IF IT ISN"T ICS
Click to expand...
Click to collapse
done all of this with same result, as soon as I try to flash ROM Odin waits a while then reports fail
Tried with latest version of Odin, 3.07 and that just sits at 'SetupConnection' in the dialog box
nokiamodeln91 said:
OK.. Odin is not able to get to the PIT mappings.. There seems to be some connection issues. Check with newer version of Odin.. Also probably a different pc.
---------- Post added at 04:55 AM ---------- Previous post was at 04:52 AM ----------
Uninstall moboginie drivers as well completely.
Click to expand...
Click to collapse
As above, tried with latest Odin, Odin3 v3.07 same result, uninstalled moboginie as well, dunno how that got on to my pc in the first place!!
Thanks for input guys
I got that mobogenie rubbish by accident once too, it came with daemon tools.
Can you perhaps try those steps on another computer?
XxPixX said:
I got that mobogenie rubbish by accident once too, it came with daemon tools.
Can you perhaps try those steps on another computer?
Click to expand...
Click to collapse
I do have an old lappy but it has Ubuntu installed and that drives me nuts lol, only other option is to put Odin plus Rom onto memory stick and visit a friend..
You said something about PIT and Ive seen some posts on it, I guess that roue is last resort?
really appreciate you help here
If there is a proper connection, then odin should be able to get the partition mapping from the phone and will be displayed as
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
nokiamodeln91 said:
If there is a proper connection, then odin should be able to get the partition mapping from the phone and will be displayed as
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
Click to expand...
Click to collapse
and if I cant get a proper connection (I can't, Odin never gets past SetupConnection) Im doomed?
That's why try on a different pc.
Would a clean install of win7 work, I have spare hard drive I could try, I'm guessing youre thinking driver probs on my pc
thanks again
rinksy55 said:
Would a clean install of win7 work, I have spare hard drive I could try, I'm guessing youre thinking driver probs on my pc
thanks again
Click to expand...
Click to collapse
Yeah. That should do.

Categories

Resources