Database Develop

[Q] (Q) Galaxy tab P1000L wont turn on

O my problem is i was trying to flash OVERCOME Icarus and following the guide on the overcome site i downloaded the stock v5 file unziped and started the included odin in download mode selected the files as instructed set repartition and pressed start. After couple minutes odin gave me a green PASS and rebooted my phone but it wont turn on soft keys are on but screen is of. If i press the power button the keys turn of. Conecting it to power outlet (original included charger) turn on soft keys after a few secs but no battery icon displayed.
After about 30 mins in this state i tried plugging it to my pc (windows 7x64Ultimate) and windows made the sound that it detected something but i cud not check what hardware it detected and odin did not detect device.
Is this a SOFT-Brick or a HARD-Brick and how can i correct my problem if possible
Edit: ok when i plugg it in windows Device manager shows SAMSUNG Android USB Modem, and SAMSUNG Android composite adb interface. Also if i start kies it tries to connect but after a while gives me a device not responding to resolve this issue reboot the device. Odin still does not detect it
Edit2: Ok tried going tru command prompt adb with adb devices command and it gives me a device conected in recovery mode i guess the is still hope still if some1 can help ill apreciate it

i was gonna reply you now , if you wait 1 second with your pm , you could see me reply you
1st of all and this is the important , overcome is not for P1000L my prove is :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
if odin can't recognize it then sorry i can't do you anything but you can try this "
Check to see if the device is actually "Hard" bricked by leaving it plugged into charge for atleast 4 hours via a mains supply (NOT USB).
If above doesn't work you will need to send your Tab To Samsung To Fix it For you or visit this link. "
sorry for your lost dude , you better read carefully later the guides , to be sure batter than to be sorry .
good luck

Rotobackup
Ok managed to get the tab in download mode with screen on(had to replace bootloader)... and now im trying a full hemidall flash from a stock roto-backup i made before i started flashing will update......

chinchulin said:
Ok managed to get the tab in download mode with screen on(had to replace bootloader)... and now im trying a full hemidall flash from a stock roto-backup i made before i started flashing will update......
Click to expand...
Click to collapse
how you managed it to go into download mode ? btw glad to hear that

download mode
looks like the tab was booting but the screen wasnt turning on i replaced the kernel with one found in post #1 from this treadhttp://forum.xda-developers.com/showthread.php?p=14728425#post14728425 and instalation continued still no screen the followed instructions from post#4 of same thread and got screen to turn on but stuck at galaxy tab boot screen, got fed up and im restoring my original rotobackup using heimdall 1.1 frontend the bar at heimdall shows 100% but no other success or failure message been like that for bout 10mins device screen show download bar but i dont see any advance btw im at the phone-yellow triangle-pc download screen

that is cool , simply you are a Worrier
did you unplugged or not yet ?
sooner or later you gonna do

still nothing
damm this tab used odin to flash my roto backup of original rom and nothing normal boot goes past galaxy tab screen into operator(telcel:mexico) animation and then gets stuck in samsung logo.
Recovery mode shows following errore:cant mount /dev/bñock/mmcblk0p2 (invalid Argument)
E:install_aplication_for_customer: cant mount DATA:
Good news looks like a software brik bad news=a really bad software brik any help will b thanked and apreciated

i think you need to flash your firmware " http://www.samfirmware.com/apps/auth/login?why=pw&try=1&wp=1&next=WEBPROTECT-p1000.htm" download it from this link ans flash it with PIT FILE

Finally
Ok Im a very happy tab owner now dont really know what worked but i tried the rom from samfirmware and the same so i retraced my steps got overcome in there again managed to get the sexy voice withoout screen went back to samfirmware at this point the error changet to cant mount dev sdcard or something like that so i went back to my own rotobackup and was back on last error.
I was almost thinking of sending it for repair when (and i dont know why i did) in the factory recovery menu i pressed home on the wipe cache option i got android with sign so i get desperate and press home dunno how many times and sudenly the cache was wiped i did the same on factory reset and after that my tab booted into my operator rotobackup(rooted ofc).
Guess I will stick to froyo for now and thanks for the help

Telcel
I'm anothere desesperated user that tried to update the Galaxy Table P1000L toandroid Gingerbread, but screen is not working anymore, I hate my self for trying doing this, What should I do? I wasn't able to download rotohammer tools as http : // files. deodexed. com/ModADroid-Galaxy-Tablet/Rotohammer/JME/ is not working anymore, help!!!! please!!!!

So... same problem here.... My tab p1000l bricked and then when i finally got the answear the battery got drained... so... if i understand it correctly if it was not a hard brick i can charge already if i plug it for at least 4 hours to charge?

Tutorial: how to unbrick your phone

Bricked my phone after trying out CM7 and then flashing Stock ROM via KDZ_FW_UPD without wiping all data.
Found a way how to fix my problem. This should work for almost all bricked phones.
Remember, this will wipe ALL DATA from your phone. I'm not responsible if something happens with your P970. Do at your own risk.
You will need:
Drivers for P970;
KDZ_FW_UPD_EN
UpTestEX_mod2_marwin
WindowsEnablerv1.1
Download
Start from here if it's first time (no drivers installed, etc):
1) Install all drivers (from Drivers folder);
2) Disable LGE Virtual Modem (Control Panel > System > Hardware > Device Manager);
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Start from here if drivers already installed:
3) Run msxml.msi (in KDZ_FW_UPD folder);
4) Delete mfc42.dll (from KDZ_FW_UPD folder);
5) Run WindowsEnabler.exe and set it to ON;
6) Run UpTestEX_mod2_marwin.exe;
7) Set your phone to S/W Upgrade mode (take out battery, while pressing Volume Up, plug USB cable).
1) Select KDZ file (download from here);
2) Click "CSE web upgrade test", then "Upgrade Start".
Chose your language and wait till phone reboots. It will take some time and could look like nothing is going on. If you see something similar to this (on your phone) for a moment, everything went OK.

maaaaaaaaaaaaan em trying it right now.....let u know as soon as i see some results
THANKS!!!!!!!!!!!!!!!!!
---------- Post added at 01:38 PM ---------- Previous post was at 01:07 PM ----------
"YES" it really works!!!
Thanks a billion times man! You saved my life
(for everyone else who is trying to follow this TUT...when i was updating it was stuck at 4% and showed a lot of errors in the log below...but i guess that didnt matter and now it works...that screen at the end is really must...and i had to force close the update tool after my phone was working)

I think this is solution for ALL BRICKED P970s that can enter into S/W Upgrade mode!!!
Very important is that this method do HARD RESET after flashing firmware so it could UNBRICK ALL of our phones.
Can anyone with bricked phone (not CM7 brick) can test it?

I a little bit edited tutorial and, yeah, it could help for all bricked phones. We just need someone who could test it out.

I linked it at RC's G+ and RootzWiki, in response to those bricking their OB's in regards with CM7. Hope they could give us feedbacks.
Sent from my Optimus Black using xda premium

cool, finally a method that can do "hard reset" without a running system or a recovery installed !!
LG would have implement the hard reset in his Recovery in the B2CAppSetup ! it would avoid lots of send back to LG customer service !!
Thanks

quyTam said:
LG would have implement the hard reset in his Recovery in the B2CAppSetup
Click to expand...
Click to collapse
No, LG would have implement the recovery key combination... It would be remedy for almost all P970 bricks...
Does anybody knows another phone with Android without hardware key combination for recovery?
Is it even possible that hardware key combination (changing bootloader) will be possible to add-on by official LG firmware update? Maybe they should do this with official 2.3 upgrade, but it is probably only dream...
PS. I forgot to thanx, ziiljuks, you're the man!

yes, recovery combination key would be better ^^
ps: I think x8 doesn't have it either

quote from rootzwiki: "adb.exe reboot recovery saved my life!!!!"
i guess we can boot into recovery with this command. i didn't know that adb environment can run with bootloop or volume up screen... can anybody confirm this?

murrun said:
i didn't know that adb environment can run with bootloop or volume up screen
Click to expand...
Click to collapse
No, it can't. You need to boot to OS and have enabled Debugging to get ADB working.
I was trying it many times when I bricked my phone. Look HERE.

It seems very good work! But i just bought my phone, i have not fllash my rom yet, since i am afraid that flashing will damage my warranty forever. Could shut body tell
Me whether there is ANY means to recover the warranty........
Sent from my LG-P970 using XDA App

yes, by reflasing stock rom !

CSE means CS_EMERGENCY
I think this does the same if you select the CS_EMERGENCY mode on KDZU.

Ilko said:
CSE means CS_EMERGENCY
I think this does the same if you select the CS_EMERGENCY mode on KDZU.
Click to expand...
Click to collapse
Nope. Tried that when I bricked my phone couple of weeks ago.
EDIT:
Tested it 5 mins. ago with CS_EMERGENCY in KDZU, and no. No hard resetting.

hmm I should test this tool again. I previously gave up that because it has never worked, until I know those kdz files must keep their name

i dont get the "CSE web upgrade test" button in the UpTestEX_mod2_marwin window.
any ideas?
tried normal upgrade but dosnt make the factory reset and keep geting boot loop.
yes another victim of CM/ > Stock
ok found it. in the type has to be in CDMA not 3GQCT

Hello,man.
There's some problems in using this method.
A guy does the upgrade,and the phone is stuck at 4% too. But unlike the situation u've met, there's not even a error in the log. Then , he has to switch off the USB(means disconnect the phone and the PC. sorry, my English is... - -#). I wanna know how much time does the upgrading process takes. Thanks.
Meanwhile ,there's another guy. He did the same thing .And the phone reboots finally. But what confuses me is that he didn't get the picture on the screen. Could you explain , thanks in my heart!
And thanks ziiljuks very much!

maybe a corrupted kdz file, try to re-download another.

elBartoFlores said:
i dont get the "CSE web upgrade test" button in the UpTestEX_mod2_marwin window.
any ideas?
tried normal upgrade but dosnt make the factory reset and keep geting boot loop.
yes another victim of CM/ > Stock
ok found it. in the type has to be in CDMA not 3GQCT
Click to expand...
Click to collapse
Download THIS package. It has all the files in one folder. Unpack it to C:\ You should get C:\P970_unbrick\*files here*
Install msxml.msi, then run Windows Enabler.exe and click on its icon in the taskbar. Icon will change and will show "ON". Then run UpTestEX_mod2_marwin.exe and do the rest of the job.

glenn_gm said:
Hello,man.
There's some problems in using this method.
A guy does the upgrade,and the phone is stuck at 4% too. But unlike the situation u've met, there's not even a error in the log. Then , he has to switch off the USB(means disconnect the phone and the PC. sorry, my English is... - -#). I wanna know how much time does the upgrading process takes. Thanks.
Meanwhile ,there's another guy. He did the same thing .And the phone reboots finally. But what confuses me is that he didn't get the picture on the screen. Could you explain , thanks in my heart!
And thanks ziiljuks very much!
Click to expand...
Click to collapse
When i followed this tut my update process was stuck at 4% and actually it "didn't" flash the stock rom...(although it was already flash before my the KDZU tool) this tool simply after giving alot of errors in the log file did a hard reset (that last screen---which actually does the magic by formatting the data partition). After that screen my phone restarted and BINGO i was at the setup wizard! then i closed the tool bcz it was stuck but my phone was working

[Q] N7000 bricked?

Hello, peeps!
So I was when starting an application, my phone doesn't respond. Tried the power button and it didn't work so I removed the battery and placed it back in.
Here's when my nightmare starts. My phone is stuck at the "GT-N7000" screen, and I cannot proceed further. I'm unable to start Recovery Mode (Vol Up + Power + Home), and only Download Mode works.
However, I tried flashing stock roms, Odin showed no progress even after almost 2 hours.
What seems to be the issue? Is it a hard brick?

Questions should be in the Q&A section.
Is odin able to detect the phone.. ( the port square in odin turns yellow/blue?).
check if there are any Kies processes running in the task manager.. kill them, restart odin and restart phone in download mode and try again.

nokiamodeln91 said:
Questions should be in the Q&A section.
Is odin able to detect the phone.. ( the port square in odin turns yellow/blue?).
check if there are any Kies processes running in the task manager.. kill them, restart odin and restart phone in download mode and try again.
Click to expand...
Click to collapse
Hi, how do I move the topic?
Odin is able to detect it. Checked and no Kies processes running at all.

where is Odin getting stuck?

nokiamodeln91 said:
where is Odin getting stuck?
Click to expand...
Click to collapse
stuck at the NAND Write part, and the progress bar shows no progress at all (the green bar thing). Could this mean hard brick?

do you have warranty? If yes, take it to Samsung and tell them to rectify it. If no warranty then, you will need to get into recovery may be by flashing a kernel using odin.

nokiamodeln91 said:
do you have warranty? If yes, take it to Samsung and tell them to rectify it. If no warranty then, you will need to get into recovery may be by flashing a kernel using odin.
Click to expand...
Click to collapse
Wow...thank you for such quick replies!!
Nope, no longer in warranty..Can I have a link to the kernel file?
Thank you so much!

Before you go about this.. try a reboot PC, reboot download mode phone. try a original USB cable and main USB port of pc and flash again,
If above still stops at NAND
http://forum.xda-developers.com/showthread.php?t=1901191
look for a tar.md5 file which is odin flashable. If you remember the build number of you phone, then pick that else get any JB kernel and flash using odin. check if odin gives a pass.

nokiamodeln91 said:
Before you go about this.. try a reboot PC, reboot download mode phone. try a original USB cable and main USB port of pc and flash again,
If above still stops at NAND
http://forum.xda-developers.com/showthread.php?t=1901191
look for a tar.md5 file which is odin flashable. If you remember the build number of you phone, then pick that else get any JB kernel and flash using odin. check if odin gives a pass.
Click to expand...
Click to collapse
I've flashed it, unfortunately it's stuck at NAND (kernel flash). Are there any alternatives?
Thanks!

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sorry for double posting, here's the screenshot..

you dont need to select it everywhere... just the PDA ONLY.
1. download http://d-h.st/FVh.. this is a PIT file.. select it in the PIT partition. Check it and also repartition.
2. select the kernel file in the PDA..
3. press start... (you will need to reboot into download mode every time to start flashing. so remove the battery.. reboot into download mode.. (vol down+home+power)... after you get the screen volume up to continue.. once the screen shows DOWNLOADING, then connect to pc .. open odin

Thanks again!
How long does it normally take for the entire process to complete? The progress bar of "Set Partition" isn't moving at all

There seems to be some issue with the USB Port or Cable or PC.. you need to check ...a full flash of rom takes about 5-10 mins.

use only the back usb port, don't use the front or extension usb ports, they often throw up problems.. good luck

elprix and
I tried everything suggested, but the progress bar doesn't even move
What are the symptoms of hard brick btw?
EDIT : I tried with Odin3 V3.09, and it is stated Re-Partition failed.
EDIT2 : Tried multiple files, progress bar not moving at all.

It don't write to NAND. But it still is able to set partition. Have you tried a different pc? Uninstall Kies completely and then again install Samsung usb drivers.
Sent from my GT-I9500 using xda premium

Hi everyone!
I experience a similar problem as the original poster! Yesterday my phone was fine, but then it rebooted and got stuck. Now I can only get in to "Download mode". There it says:
Odin Mode
Product Name: GT-N7000
Custom binary download: No
Current binary: Samsung Official
I've had it running Paranoid Android successfully for months and then this happened! So where do I go from here,,,? I have Odin downloaded, drivers installed, so what should I try to flash and in what order?
I would be thankful for any help - feel a bit handicapped without a phone!

316097 said:
Hi everyone!
I experience a similar problem as the original poster! Yesterday my phone was fine, but then it rebooted and got stuck. Now I can only get in to "Download mode". There it says:
Odin Mode
Product Name: GT-N7000
Custom binary download: No
Current binary: Samsung Official
I've had it running Paranoid Android successfully for months and then this happened! So where do I go from here,,,? I have Odin downloaded, drivers installed, so what should I try to flash and in what order?
I would be thankful for any help - feel a bit handicapped without a phone!
Click to expand...
Click to collapse
Exactly what happened to me! Running on PA too! Any solutions?

samsung gear bricked after update

hey guys i just have a question i have a galaxy gear watch i did the update to the mk7 firmware and then tried to use odin after would to put on the null 10.1 i looked for the debbuging option on the phone but it was gone then i came across another video that tells you how to put it in debug mode anyway that was after the fact now my gear watch is stuck on the ; ( firmware upgrade encounter an issue please select recovery mode in kies and try again }
is the gear dead or can some one plesae help me out
thanks in advance

can you get into download mode or recovery?

Reply
omniwolf said:
can you get into download mode or recovery?
Click to expand...
Click to collapse
Firs off let me say thanks for the quick response
Yes I can get into both of those modes but when I try to flash it freezes' what I did
Wrong was not doing the new debugging method since I did the update to mk7
My debug option under gear info is gonna but I saw I video on how to do it but that was
After I got stuck at this point will your method get me out of this jam

Are you sure twrp installed on your gear?

alwayswatching said:
Firs off let me say thanks for the quick response
Yes I can get into both of those modes but when I try to flash it freezes' what I did
Wrong was not doing the new debugging method since I did the update to mk7
My debug option under gear info is gonna but I saw I video on how to do it but that was
After I got stuck at this point will your method get me out of this jam
Click to expand...
Click to collapse
I have forced my gear into this mode issue before, no worries you can restore your gear.
Reboot your gear, Once it is on the " ( firmware upgrade encounter an issue please select recovery mode in kies and try again }"
connect it to your computer, the open odin and reflash your mk7 firmware.
This will get you back to stock firmware.
Note: Info was available here in my Tutorial.
(Note 2: Null_ roms are not flashed using odin)

Reply
almulder1092 said:
I have forced my gear into this mode issue before, no worries you can restore your gear.
Reboot your gear, Once it is on the " ( firmware upgrade encounter an issue please select recovery mode in kies and try again }"
connect it to your computer, the open odin and reflash your mk7 firmware.
This will get you back to stock firmware.
Note: Info was available here in my Tutorial.
(Note 2: Null_ roms are not flashed using odin)
Click to expand...
Click to collapse
Guys thanks for the replies no I'm not sure if it loaded the trw but I am
Sure that it took the mk7 update I was trying to load the trw when it got stuck
I am trying to flash it back but it is taking forever its been running since 9pm last night
Will this work even if its not in debug mode is there a way to force it into debug mode

might be time for the typical Odin troubleshooting:
try a new computer
try a new microUSB cable

guys i have tried flashing the mk7 back no good i hope its not dead i don't know what else to do it starts running and gets stuck on the system part

you guys are awesome it worked i had to use odin 307 instead of 309 thanks again guys you guys rock
almulder1092 thanks a bunch man worked like a charm im back in buisnees thanks so much to you and omniwolf and also Santaclauswitz
you guys took time to help when you didn't have to and i appreciate that greatly

alwayswatching said:
you guys are awesome it worked i had to use odin 307 instead of 309 thanks again guys you guys rock
almulder1092 thanks a bunch man worked like a charm im back in buisnees thanks so much to you and omniwolf and also Santaclauswitz
you guys took time to help when you didn't have to and i appreciate that greatly
Click to expand...
Click to collapse
If anyone can help - I am totally new to rooting, and my Galaxy Gear is bricked. It won't boot past the "Samsung Galaxy Gear" logo - and It says "No OS Installed in recover mode. I can boot into Recovery, and Download.
Please assist me into installing an OS.
I had tried installing the custom ROM I tried before (but wanted to remove because it wasn't allowing data connections on the gear) but i need to allow USB debug - but Obviously I cannot access this.
Please help if anyone can!
Thanks in advance!

DHabkirk said:
If anyone can help - I am totally new to rooting, and my Galaxy Gear is bricked. It won't boot past the "Samsung Galaxy Gear" logo - and It says "No OS Installed in recover mode. I can boot into Recovery, and Download.
Please assist me into installing an OS.
I had tried installing the custom ROM I tried before (but wanted to remove because it wasn't allowing data connections on the gear) but i need to allow USB debug - but Obviously I cannot access this.
Please help if anyone can!
Thanks in advance!
Click to expand...
Click to collapse
Just flash stock rom via odin

Garbled Screen When trying to get into recovery mode.
I've update my Gear to Tizen then tried to get back to stock state to install null_
I've followed this instructions:
http://forum.xda-developers.com/showthread.php?t=2776157
Did not work (process completed but unbootable).
Then tried installing TRWP
http://liliputing.com/2013/11/twrp-custom-recovery-samsung-galaxy-gear-smartwatch.html
Not I have it unbootable. ( it's stuck at Samsung logo, like the one from stock V1 android firmware )
When I tried to get into recovery I get a garbled screen like the one attached. Unresponsive device.
Ideas?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Hi, I was unable to install the new stock rom. I am now at the stage (firmware uprage encoutered .... please sellect recovery ....... I read advice on how to restore, but the problem is that I can not download a recovery mod. Upon restart, so it is restored to the same information. Do not know what to do?

Do a search
http://forum.xda-developers.com/showthread.php?p=53630254
Sent from my SM-G900T using Tapatalk

omniwolf said:
can you get into download mode or recovery?
Click to expand...
Click to collapse
i have the same problem but i cant go to the download mode

I dont kmow what happens with mine, is says firmware upgrade encountered an issue, please señect recpvery in kies, when I try to flash through odin, it stays at zImage, and don't continue, anyone can help me?

alwayswatching said:
hey guys i just have a question i have a galaxy gear watch i did the update to the mk7 firmware and then tried to use odin after would to put on the null 10.1 i looked for the debbuging option on the phone but it was gone then i came across another video that tells you how to put it in debug mode anyway that was after the fact now my gear watch is stuck on the ; ( firmware upgrade encounter an issue please select recovery mode in kies and try again }
is the gear dead or can some one plesae help me out
thanks in advance
Click to expand...
Click to collapse
Hey gang, count me into this discussion. Kies killed my gear too. i'm stuck in a boot loop -- can't access download mode or recovery.

sameog said:
Hey gang, count me into this discussion. Kies killed my gear too. i'm stuck in a boot loop -- can't access download mode or recovery.
Click to expand...
Click to collapse
are you stuck in the firmware encountered an error message ? If yes, does Odin still identify your watch when you plug it in ?? I ended up with the firmware error screen when attempting to upgrade to Tizen without following the correct order of items to flash.
If Odin can read your watch, you can probably reset the watch. If you plug it in, and Odin does not show it as active - try another usb slot on your computer.
I had to "start" Odin three times before it finally started to flash my watch again.
read this - it is what helped me
http://forum.xda-developers.com/showthread.php?t=2794780

bill_in_mtl said:
are you stuck in the firmware encountered an error message ? If yes, does Odin still identify your watch when you plug it in ?? I ended up with the firmware error screen when attempting to upgrade to Tizen without following the correct order of items to flash.
If Odin can read your watch, you can probably reset the watch. If you plug it in, and Odin does not show it as active - try another usb slot on your computer.
I had to "start" Odin three times before it finally started to flash my watch again.
read this - it is what helped me
http://forum.xda-developers.com/showthread.php?t=2794780
Click to expand...
Click to collapse
@bill_in_mtl: OK. I'll try this out when I get home from work. Thanks for this in advance. =)

I faced that too. Then odin could not recognise the gear. So only way was to restart laptop and change USB port. Then flash NE9. Then flash OA2.
However after that you might face gear manager connect issues.
Go here
http://forum.xda-developers.com/showthread.php?p=62050646
I posted my experience and how to resolve it

Samsung Note 8 N950F Boot Loop after latest update

Hey
After the latest update, every time I called with the Note 8, it would restart and every time I would switch it off, it would start back on. So the first thing I did was boot to recovery mode and wipe cache partition. When I restarted the phone, I would get a "No command" error and it would always boot to the recovery mode. Next, I tried flashing the latest firmware (I made sure to use the right carrier, VDH) from SamMobile using Odin which still didn't work. Then I tried NAND erase and re-partition and this didn't work either.
I am very new to this so any solutions would be greatly appreciated
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

NoteEight said:
Hey
After the latest update, every time I called with the Note 8, it would restart and every time I would switch it off, it would start back on. So the first thing I did was boot to recovery mode and wipe cache partition. When I restarted the phone, I would get a "No command" error and it would always boot to the recovery mode. Next, I tried flashing the latest firmware (I made sure to use the right carrier, VDH) from SamMobile using Odin which still didn't work. Then I tried NAND erase and re-partition and this didn't work either.
I am very new to this so any solutions would be greatly appreciated
View attachment 5256493View attachment 5256495
Click to expand...
Click to collapse
NoteEight said:
Hey
After the latest update, every time I called with the Note 8, it would restart and every time I would switch it off, it would start back on. So the first thing I did was boot to recovery mode and wipe cache partition. When I restarted the phone, I would get a "No command" error and it would always boot to the recovery mode. Next, I tried flashing the latest firmware (I made sure to use the right carrier, VDH) from SamMobile using Odin which still didn't work. Then I tried NAND erase and re-partition and this didn't work either.
I am very new to this so any solutions would be greatly appreciated
View attachment 5256493View attachment 5256495
Click to expand...
Click to collapse
When you tried to flash stock with Odin did it pass? Fail? Did it give an error code? Did you download the latest filmware? As you can't flash older filmware than what is already on the phone.

stonedpsycho said:
When you tried to flash stock with Odin did it pass? Fail? Did it give an error code? Did you download the latest filmware? As you can't flash older filmware than what is already on the phone.
Click to expand...
Click to collapse
Hey, thanks for the reply
When I flashed with stock firmware, Odin said it passed. And I used the latest firmware for my carrier from SamMobile

NoteEight said:
Hey, thanks for the reply
When I flashed with stock firmware, Odin said it passed. And I used the latest firmware for my carrier from SamMobile
Click to expand...
Click to collapse
I was hoping that it was an issue with Odin so I could possibly help you, even having a look on the internet doesn't being much help other than trying a factory reset. I've been on xda for years and never seen this issue before. Hopefully someone more knowledgeable will see your post, I suggest bumping your thread every 24 hrs.
Having tried flashing stock with Odin which usually resolves most bugs I would guess that it is a hardware issue and if you're able to, take it to a service centre.
If you do find a solution please post it here on XDA for anyone who searches this in the future

stonedpsycho said:
I was hoping that it was an issue with Odin so I could possibly help you, even having a look on the internet doesn't being much help other than trying a factory reset. I've been on xda for years and never seen this issue before. Hopefully someone more knowledgeable will see your post, I suggest bumping your thread every 24 hrs.
Having tried flashing stock with Odin which usually resolves most bugs I would guess that it is a hardware issue and if you're able to, take it to a service centre.
If you do find a solution please post it here on XDA for anyone who searches this in the future
Click to expand...
Click to collapse
Thanks for trying. If I do find the solution, I'll be sure to post it here

Looks like the partition in your internal SSD has been corrupted and needs to be reformatted. If that doesn't work then you need to have the motherboard on your device replaced.

iceepyon said:
Looks like the partition in your internal SSD has been corrupted and needs to be reformatted. If that doesn't work then you need to have the motherboard on your device replaced.
Click to expand...
Click to collapse
How would I go about doing this?

Bump

The same thing happened to me. I tried everything possible. I tried a new flash via odin. unsuccessful. only Download mode works, nothing else works, not even recovery mode, black screen.

Have anyone found the solution to fix this issue ?

im having similar problems