Database Develop

tytn 2 not charging

hi!
i was just wondering, my tytn 2 is not charging, when i look at the battery meter, it says charging, but instead of going up. it goes down, the amber light
the signals charging is gone.
im sure its not the battery. coz i did get a charger, the one where u put probes on the + and - terminal of the battery, it charged. the battery is working now. however, i couldnt charge via the phone.
the red light came up before which indicates not charging so what do i do now?
someone suggested to hard reset it. i tried it but nothing. still the same. i reflashed it... nothing... now using the hyperdragon rom... still the same...
any ideas?

btw, when i plug in the charger, amber light is there... however, not for long, light turns off, but the charging / plugged into the charger symbol is there

as far as my personal experience goes, i have noticed this behavior only when the battery overheats while charging. in the hottest weather, this has NEVER happened for me. it only happens sometimes if my device screen is on WITH wifi WITH bluetooth WITH data connection WITH some heavy processing program running. this causes heating of the components and also leaves little power to charge the battery, because most of the charger's power is being redirected to power the components in use.
so, the device will charge for a few minutes and will interrupt the charging if the temperature rises. the charging will resume again when the temperature comes back down.
you can test if this is happening with your device by observing how long it charges before stopping, first without a fan and then with a fan blowing over the battery with the back cover removed.
if the charging lasts longer when the device is being cooled with a fan, then you are likely facing temperature issues.

xxxpongxxx said:
btw, when i plug in the charger, amber light is there... however, not for long, light turns off, but the charging / plugged into the charger symbol is there
Click to expand...
Click to collapse
Try to clean your battery terminals and see if that can help... http://forum.xda-developers.com/showthread.php?t=358136
Also check here http://forum.xda-developers.com/showthread.php?t=448467
Your same issue

solved my problem...
i was so pissed, all the solutions did not work... i decided to open it up
when i opened it, i saw that there is some dirt / corrosion on some lines
cleaned each and every one of them.
while it was open, plugged in the battery... then the charger...
after 2 minutes... battery bar went up! it is now charging!!! and
best thing... it also syncs!

Good to know that you solved your problem.

thanks so much. its ur post that really helped

lucky you , now mine cant even charge . Even charge the led indicator turn red not orange for few hours

johnkor said:
lucky you , now mine cant even charge . Even charge the led indicator turn red not orange for few hours
Click to expand...
Click to collapse
u opened it up also? my main problem was. when my battery drained, the led was red... didnt turn orange even when its plugged for more than an hour already

same thing

johnkor said:
same thing
Click to expand...
Click to collapse
did u try opening it already? coz mine never got wet, maybe its the moisture in the air, eventually... accumulating in there...

Xperia SP wont respond (no flashing problem or root problem)

Hello my Xperia Sp just run out of battery and shut down.I pluged it in saw the sony logo and when i tried to turn it on it would not respond.
The only thing it did was kept the red light on (indicating charging).I tried pressing the off button for over 30 seconds with no results. Not it is stuck and i cant do anything about that.
Help please.

Nevermind the problem got fixed by itself.
The battery (about 2 % run out and the phone kinda reseted itself.It opened just fine.
So if anyone else gets this problem just let your battery drain itself.

jackaros said:
Hello my Xperia Sp just run out of battery and shut down.I pluged it in saw the sony logo and when i tried to turn it on it would not respond.
The only thing it did was kept the red light on (indicating charging).I tried pressing the off button for over 30 seconds with no results. Not it is stuck and i cant do anything about that.
Help please.
Click to expand...
Click to collapse
Just to confirm you plugged it into a mains supply? USB from your computer to phone charging is not enough to kick start a totally dead battery.
If you have plugged it in to a wall socket and it still doesn't work, give it some time.
I think the battery and the phone's software combine to stop the phone operating at unsafe voltages, the safe operating range for a standard lithium ion batteries is 3.2-4.2 volts (though android may be different). They spend most of their time at 3.7 volts though and this is why they are described as such when you buy them separately.
If, for some reason your phone's software thinks your battery is at 3.1 volts, it won't do anything until it thinks it's at 3.2. Similarly if a protected battery is taken below 3.2 volts it won't provide any power until it hits its minimum voltage. In theory your phone should have cut out before the protection cut in, but bad stuff happens to good people.
Sometimes a protected battery gets drained so much that the tiny flow of electricty required to power the protection circuit stops and as the ultimate failsafe, protected batteries stop working when this circuit is not functioning.
(I'm talking about standard batteries here, not necessarily phone ones)
Sometimes cheap basic chargers won't be able to get such batteries working, but better chargers are able to send tiny trickles to a battery to start the protection circuit and make such batteries charge again. I'd be very surprised if android didn't take this into account and have some way of ensuring over-discharged batteries with a tripped protection circuit can be charged. That said I'm not sure whether the protection is all software on mobile phones?
Like I say give it some time - getting that first .1 of a volt can take a while when the battery is totally flat. If it hasn't changed after at least 2 hours then I'd worry.

Parkside said:
Just to confirm you plugged it into a mains supply? USB from your computer to phone charging is not enough to kick start a totally dead battery.
If you have plugged it in to a wall socket and it still doesn't work, give it some time.
I think the battery and the phone's software combine to stop the phone operating at unsafe voltages, the safe operating range for a standard lithium ion batteries is 3.2-4.2 volts (though android may be different). They spend most of their time at 3.7 volts though and this is why they are described as such when you buy them separately.
If, for some reason your phone's software thinks your battery is at 3.1 volts, it won't do anything until it thinks it's at 3.2. Similarly if a protected battery is taken below 3.2 volts it won't provide any power until it hits its minimum voltage. In theory your phone should have cut out before the protection cut in, but bad stuff happens to good people.
Sometimes a protected battery gets drained so much that the tiny flow of electricty required to power the protection circuit stops and as the ultimate failsafe, protected batteries stop working when this circuit is not functioning.
(I'm talking about standard batteries here, not necessarily phone ones)
Sometimes cheap basic chargers won't be able to get such batteries working, but better chargers are able to send tiny trickles to a battery to start the protection circuit and make such batteries charge again. I'd be very surprised if android didn't take this into account and have some way of ensuring over-discharged batteries with a tripped protection circuit can be charged. That said I'm not sure whether the protection is all software on mobile phones?
Like I say give it some time - getting that first .1 of a volt can take a while when the battery is totally flat. If it hasn't changed after at least 2 hours then I'd worry.
Click to expand...
Click to collapse
The phone was pluged in the wall socket.After this i tried to turn it on (while pluged) nothing happened so i unpluged it to press the off button (i upluged it because i could not reach the button because i had the case on) but the red light ( at the bottom of the device indicating charging) did not turn of.So i tried to reset the device by pressing the off button but i waited for almost 30 seconds (while pressing it) and nothing ... not even a vibration.So i left the phone away with the light stick on till the 1 % left was drained and the phone shut down due to lack of power.
So then i pluged it back in to the wall socket and it started charging again and so i turned the device on.This time it responed and opened up .Now nothing is wrong

It happened again.... i dont know the problem but the solution was the same...

jackaros said:
The phone was pluged in the wall socket.After this i tried to turn it on (while pluged) nothing happened so i unpluged it to press the off button (i upluged it because i could not reach the button because i had the case on) but the red light ( at the bottom of the device indicating charging) did not turn of.So i tried to reset the device by pressing the off button but i waited for almost 30 seconds (while pressing it) and nothing ... not even a vibration.So i left the phone away with the light stick on till the 1 % left was drained and the phone shut down due to lack of power.
So then i pluged it back in to the wall socket and it started charging again and so i turned the device on.This time it responed and opened up .Now nothing is wrong
Click to expand...
Click to collapse
You left the phone in the charger to drain or not? If i put the charger off then red light isn't opened..
Also, how many hours did you wait?

billaras481 said:
You left the phone in the charger to drain or not? If i put the charger off then red light isn't opened..
Also, how many hours did you wait?
Click to expand...
Click to collapse
It took about half an hour because of the battery level being low.

Guys im having the same problem.. anyone who can help will be appreciated.

[Q] [Help Thread] Nook HD not booting at all

I recently went on a 3 month trip. Before I left, my nook was working perfectly fine, when i got back, it didn't work at all. It's not dead because i left it plugged in overnight but it still didn't turn on. when i plug it in the LED goes from orange to green and then off (or green to orange, i can't remember). The screen doesn't turn on at all. I can't get to recovery either.
This is a Nook HD, I believe it had CM11.
:crying:
Can this be fixed
or should i plan it's funeral

Same here
The same has happened to me. Screen doesn't turn on, but there is power, I can play it into my laptop and something is there, just not enough.
Good excuse for a new tablet!

It can be fixed. I've done it before. It has to do with the fstrim not being compatible with certain hardware versions of our device. If I can remember how I fixed it, I'll post it here. Trying to fix mine (again).

tambourineman86 said:
It can be fixed. I've done it before. It has to do with the fstrim not being compatible with certain hardware versions of our device. If I can remember how I fixed it, I'll post it here. Trying to fix mine (again).
Click to expand...
Click to collapse
If would be fab if you could fix. Seems to be a common issue

I was able to fix it. YMMV.
1) Make sure the Nook is completely off and unplugged
2) Take out your sdcard
3) Hold down power button until the "battery depleted" icon shows, then promptly plug in the power before the icon disappears.
4) Let it set. The screen will go black, then it will attempt to boot and get stuck on the faint black screen, but this time, the charging light should stay amber.
If you want to be safe, wait until the device reboots itself. That could take hours though. If you're plugged into the wall wait at least 30 - 45 minutes before holding the power button down til it shuts down and then rebooting it (with the sdcard inserted).
Good luck, I hope it works for you.
EDIT: Also, I've read this may also have to do with wifi sending the device into some sort of strange bootloop when the screen is off. I personally believe it has more to do with the fstrim of JB but perhaps changing the wifi sleep policy may prevent this issue from happening again. I'm skeptical, but figured I'd pass that info along if anyone wants to try it as well.

tambourineman86 said:
I was able to fix it. YMMV.
1) Make sure the Nook is completely off and unplugged
2) Take out your sdcard
3) Hold down power button until the "battery depleted" icon shows, then promptly plug in the power before the icon disappears.
4) Let it set. The screen will go black, then it will attempt to boot and get stuck on the faint black screen, but this time, the charging light should stay amber.
If you want to be safe, wait until the device reboots itself. That could take hours though. If you're plugged into the wall wait at least 30 - 45 minutes before holding the power button down til it shuts down and then rebooting it (with the sdcard inserted).
Good luck, I hope it works for you.
EDIT: Also, I've read this may also have to do with wifi sending the device into some sort of strange bootloop when the screen is off. I personally believe it has more to do with the fstrim of JB but perhaps changing the wifi sleep policy may prevent this issue from happening again. I'm skeptical, but figured I'd pass that info along if anyone wants to try it as well.
Click to expand...
Click to collapse
Not sure we have the same problem. My screen doesn't come on at all, I don't get a battery depleted icon, no matter how long I hold in the power button. The only sign of life I get is when it's plugged in, when it goes from orange to green after about 10 seconds.
Thanks for the help, but I think it's a lost cause.

YMMV. But mine was the same issue. You should be able to get the icon by holding the power button down for 5 or 6 seconds. I'd say just eff with it until that icon appears. Try different button combinations. I used power and home trying to get the icon to show.

developerbuzz said:
when it goes from orange to green after about 10 seconds.
Thanks for the help, but I think it's a lost cause.
Click to expand...
Click to collapse
Anyway... since people are continually running into this kind of issue...
Give or take 21 seconds after turning orange it turns green during actual boot cycle into rom
Give or take 10 seconds after turning orange is cwm internal recovery.
After about 10 seconds the charging screen image disappears.
The charging screen image once finally no longer may not show up again until full power off/on (holding power button > 10 seconds or full battery discharge). Unplugging and plugging back in does nothing except making the device look bricked if there's too much light shining on it.
Device may not automatically leave the above state under a specific situation(s). May still need manual full power off/on.
Guessing 10 seconds could also be something else during the early/late boot process or other. The light changing color though should indicate that something is indeed happening.
Light should stay green during the boot process if its completely and fully no questions asked 100%. If you go based on that than yours doesn't appear to be completely fully charged which should either mean its turning on and using battery or not charging correctly.
The light turning off is curious. The device could be shutting off. If light comes back on a moment later then the device has rebooted. if the light stays off = n/a.
If its booting into recovery then the device would be available via adb. At that point it could be further evaluated.
On the off chance the screen was damaged it should boot and usb should be available via computer as well as adb.
If not then its probably toast unless its simply not getting a good enough current causing mislead battery stats and/or not enough energy to get to charging screen (bad wall power adapter in use, damaged power cable - though could be bad battery, defect, damage or whatever). OR there's some major error on behalf of the user happening (think should have tried that in the morning not while 1/2 asleep or came home from long trip and forget how that works).
Maybe the only other things are the emmc brick bug, was left sitting in the sun or heat or ocean air or other physical damage/defect even to the power port as well.
Or maybe it was mad that you left it. Shouldn't have hurt its feelings you know. At least its not crying battery acid on you.
That should just about cover everything except for the things not mentioned. Since its your device, you decide what happened.
Its complicated so anyone see any improvements, clarifications, or mistakes? Please put it in a post.

Jsorren said:
when i plug it in the LED goes from orange to green and then off (or green to orange, i can't remember). The screen doesn't turn on at all.
Click to expand...
Click to collapse
Bumping this thread to make it aware that there is a real answer. I have been able to duplicate this problem and rather easily too.
The problem is indeed from bad power. The device isn't receiving the correct amount of power needed to charge and start from a fully discharged battery.
To safely* duplicate this you can use a usb extension that isn't fully connected to the nook power cable. You may need to fully connect it first then slowly disconnect/connect till the light turns green when it should actually be charging. It won't actually charge in this state, or if it is, its very little and the battery percentage will continue to drop.
Leave the cable as is and unplugged. After the tablet is fully discharged, connect the usb cable. The light will change through the modes and turn off. The device will not turn on.
There are probably other ways to cause the problem like for instance a portable usb battery that doesn't put out enough juice (not the orange kind). Etc.
* It didn't hurt mine, but not my fault if it breaks your device.

sandsofmyst said:
Bumping this thread to make it aware that there is a real answer. I have been able to duplicate this problem and rather easily too.
The problem is indeed from bad power. The device isn't receiving the correct amount of power needed to charge and start from a fully discharged battery.
To safely* duplicate this you can use a usb extension that isn't fully connected to the nook power cable. You may need to fully connect it first then slowly disconnect/connect till the light turns green when it should actually be charging. It won't actually charge in this state, or if it is, its very little and the battery percentage will continue to drop.
Leave the cable as is and unplugged. After the tablet is fully discharged, connect the usb cable. The light will change through the modes and turn off. The device will not turn on.
There are probably other ways to cause the problem like for instance a portable usb battery that doesn't put out enough juice (not the orange kind). Etc.
* It didn't hurt mine, but not my fault if it breaks your device.
Click to expand...
Click to collapse
I actually ended up fixing it yesterday!! I haven't touched it in about 3 months, and I was planning on just throwing it out getting rid of it some how. For the heck of it, I decided to plug it in, assuming that it was gonna go through the same process. But this time it went from green to amber, but it never went off. So I pressed the power button and the battery icon appeared. This was a really good sign. So I left plugged in for about 5 to 10 minutes then tried to power on.:fingers-crossed: As soon as I saw that '' Nook" boot up screen, my heart stopped. It booted up perfectly and I almost blew up from excitement :victory:. So I then flashed the stock firmware back onto it, so this would never happen again.
I guess the battery had to be completely depleted or just had to cool down. Idk but either way this was one heck of a miracle
So I recommend for anyone having this problem to just leave it off and don't mess with it. I wouldn't say for 3 months like I did but maybe test it each week or wait a month if you have good patience

Wow. Man, that's awesome! Glad you posted that update on it. Thought if you had posted an update it would be the opposite as in trashed it
Actually, I guess only you could answer if you had also moved/unplugged the power cable from the wall adapter or put it into a different wall adapter, etc. Thinking there could have been a difference there.
These modern day devices are so finicky, guess anything is possible. Like you say, maybe sitting without power is another answer.

From some experimentation I have etermined that your power adapter (that plugs into the outlet) is the issue. It does not like to be leaft plugged in indefinately. It will continually use power even when the nook is not plugged in.
Also, if you use a differnt adapter you will have the same problem unless it is also of the exact same voltage and amps.

Help! Battery drained, phone won't turn on, battery charging icon flashes on and off?

My phone had been working perfectly fine, as well as charging perfectly fine. Recently, I accidentally let it drop to 0%, which I don't usually do. I went to plug it into the same wall outlet as always, but instead of the usual charge process, the battery icon with the lightning bolt in the middle simply flashes on the screen and then turns off, which happens over and over again.
It should be noted as well that about 3 weeks ago my phone get fairly wet. After that incident, I turned it off till it dried, powered it up, and everything appeared to be totally ok.
Other facts:
-I can safely get into the recovery menu (power + vol down), which is stable, but any menu selections result in the Motorola splash screen for a quick second and then the phone powering down.
-The computer will recognize the connection to the phone.
Attempts to resolve:
-New cable, new usb hub, new wall outlet
-Trickle charge from the computer (same flashing)
-Phone in rice to remove moisture
-Toothbrush cleaning of Micro-usb port (suggestion from another thread)
I'm pulling my hair out, and I am considering prying off the back and replacing the battery. I have searched other threads, but have seen various solutions none of which worked for me. If anybody has any idea how I can fix this please help!!! Thanks in advance.

DroidGuy321 said:
My phone had been working perfectly fine, as well as charging perfectly fine. Recently, I accidentally let it drop to 0%, which I don't usually do. I went to plug it into the same wall outlet as always, but instead of the usual charge process, the battery icon with the lightning bolt in the middle simply flashes on the screen and then turns off, which happens over and over again.
It should be noted as well that about 3 weeks ago my phone get fairly wet. After that incident, I turned it off till it dried, powered it up, and everything appeared to be totally ok.
Other facts:
-I can safely get into the recovery menu (power + vol down), which is stable, but any menu selections result in the Motorola splash screen for a quick second and then the phone powering down.
-The computer will recognize the connection to the phone.
Attempts to resolve:
-New cable, new usb hub, new wall outlet
-Trickle charge from the computer (same flashing)
-Phone in rice to remove moisture
-Toothbrush cleaning of Micro-usb port (suggestion from another thread)
I'm pulling my hair out, and I am considering prying off the back and replacing the battery. I have searched other threads, but have seen various solutions none of which worked for me. If anybody has any idea how I can fix this please help!!! Thanks in advance.
Click to expand...
Click to collapse
Either there is something wrong with your battery, or there is something wrong with the USB port. If the USB port is the problem, you can use wireless charging instead. I'm a fan of this one, personally: https://www.amazon.com/gp/product/B00S7IBDGW/ref=oh_aui_search_detailpage?ie=UTF8&psc=1.
Also, are you unlocked? If so, what battery percentage does TWRP say?

TheSt33v said:
Either there is something wrong with your battery, or there is something wrong with the USB port. If the USB port is the problem, you can use wireless charging instead. I'm a fan of this one, personally:
Also, are you unlocked? If so, what battery percentage does TWRP say?
Click to expand...
Click to collapse
Thanks for the quick reply. It does seem like a battery problem, however it is just so coincidental that it stopped working after I let the battery drain to 0%, when only hours previously it was in use and charging without any issue at all.
Also, if there was a problem with the micro-usb port, I would think that a computer wouldnt be able to read the phone, but when I plug it in it is recognized as an ADB device.
I have another turbo with a cracked screen, I'm thinking about dissecting both and putting that battery in this phone as a replacement.
And unfortunately I am not unlocked :/.

Update
Well, after some further experimentation, I've gotten it working again. The solution was to charge it for like 5 hours, then let it sit off charge for an hour, and then it would boot... bizarre combination of actions. It has since dies twice and I've had to use this method.
It is working for now if I don't let the battery drop below like 15%. Seems more like a software or hardware issue to me, and i'm still trying to resolve it, so if anybody has any suggestions please let me know.
Also, what is the best way to re-calibrate the battery, maybe that could help?

DroidGuy321 said:
It is working for now if I don't let the battery drop below like 15%. Seems more like a software or hardware issue to me, and i'm still trying to resolve it, so if anybody has any suggestions please let me know.
Also, what is the best way to re-calibrate the battery, maybe that could help?
Click to expand...
Click to collapse
If you can't let the battery go below a certain percentage, it might be an early sign of failure. The voltage might drop suddenly and unexpectedly towards the end of discharge, prompting the phone to emergency-shutdown.
As for calibrating the battery...it depends on who you ask. I would say that running it to shutdown (even if shutdown is "15%") and then charging it to 100% should do it, since that gives the controller a full set of data with which to extrapolate a discharge curve. Clear your cache in recovery, so hopefully the OS will pick up on this to accurately track the battery's actual state.
Get Kernel Adiutor or something similar to check your battery's health, too. If there's something obviously badly wrong, it should report something other than "Good".

If you note when your battery dies abruptly and you immediately reboot the back light is very poor. Almost flickering.
I think this is a battery issue of not being able to feed enough amperage.
...however. My phone was doing this and after a full clean reflash it has stopped. I question if this is because I am running less apps now. Or if perhaps somehow the battery managed to lose its memory. (Li ion is an odd duck..)

mrkhigh said:
If you note when your battery dies abruptly and you immediately reboot the back light is very poor. Almost flickering.
I think this is a battery issue of not being able to feed enough amperage.
...however. My phone was doing this and after a full clean reflash it has stopped. I question if this is because I am running less apps now. Or if perhaps somehow the battery managed to lose its memory. (Li ion is an odd duck..)
Click to expand...
Click to collapse
Septfox said:
If you can't let the battery go below a certain percentage, it might be an early sign of failure. The voltage might drop suddenly and unexpectedly towards the end of discharge, prompting the phone to emergency-shutdown.
As for calibrating the battery...it depends on who you ask. I would say that running it to shutdown (even if shutdown is "15%") and then charging it to 100% should do it, since that gives the controller a full set of data with which to extrapolate a discharge curve. Clear your cache in recovery, so hopefully the OS will pick up on this to accurately track the battery's actual state.
Get Kernel Adiutor or something similar to check your battery's health, too. If there's something obviously badly wrong, it should report something other than "Good".
Click to expand...
Click to collapse
Thanks for the pointers. So strange, first it died at 40%, then 30% then 15%. Now, it is still dying early but I am no longer facing the issue I originally had, it will show normal charging when off, and boots up right away. Sure hope its not some ticking battery time bomb, its still a relatively new refurb.
I attempted the charge calibration so we shall see if it helps. I also did a factory reset for the hell of it, since I am on stock and can't reflash. Perhaps I'm in the clear, that would be awesome. Still no idea what the issue was in the first place though, which will annoy me to no end.

Htc One m7 won't turn on

I know this phone is old and a new one has been ordered, but I just want to get some pictures off of it before it becomes trash. I can only get it to turn on to the logo screen and then it goes off. It won't charge, but will show the led from time to time blinking red and the battery icon on the screen and then it disappears. I can get to the bootloader screen, but it's locked so I can't do anything. Any suggestions/help? Please?!

Noobalicious said:
I know this phone is old and a new one has been ordered, but I just want to get some pictures off of it before it becomes trash. I can only get it to turn on to the logo screen and then it goes off. It won't charge, but will show the led from time to time blinking red and the battery icon on the screen and then it disappears. I can get to the bootloader screen, but it's locked so I can't do anything. Any suggestions/help? Please?!
Click to expand...
Click to collapse
It's not clear to me exactly what your issue is (don't have 1+) but does sound like charging issue, might just be usb connector (damaged/dirty) or more problematicly the battery or battery charging circuitry. A usb connector with debris in should be easier fix.
If you have some electrical knowledge (or take to repair shop & they can do it) you should be able to overcome phone not charging by opening phone up to either charge battery via accessing back of usb connector/pcb/pwb or connect another battery. (Be careful playing with electricity & charges )
Note: if the battery has been run down too far by you keep turning it on then the battery will not charge normally again as it needs some residual charge in it to become charged (ie when your phone shows zero charge really the battery retains a few % otherwise it's impossible to recharge, though a special charger can supply a high charge initially to bring them back to life sometimes, but you probably need a battery specialist for that, so much easier to swap battery)
if it's soft brick then that is a whole different story.

I'm not electrically inclined, so I'll likely take it to a local shop. Thanks for your response.