[Q] i9305 touchscreen unresponsive after flash - Galaxy S III I9305 (4G LTE + 2GB RAM) Q&A, Help &

Hi folks,
i've flashed the bootloader of my i9305 with a wrong version, meant for a i7100 ... I've mismatched two directories while choosing it from Odin.
The result is that the phone boots, but the touchscreen is unresponsive. Only the two softbuttons right and left of the home button give a response. The hardware buttons works properly, so I think it's a software problem.
I've flashed a stock rom, it worked through but without any positive effect.
What can I do to fix this ?
In this video you'll see that the phone seems to work, but I can't go further than the welcome screen.
youtu.be/nEN1g7jY9m8
Thank you very much !

flyjodel said:
Hi folks,
i've flashed the bootloader of my i9305 with a wrong version, meant for a i7100 ... I've mismatched two directories while choosing it from Odin.
The result is that the phone boots, but the touchscreen is unresponsive. Only the two softbuttons right and left of the home button give a response. The hardware buttons works properly, so I think it's a software problem.
I've flashed a stock rom, it worked through but without any positive effect.
What can I do to fix this ?
In this video you'll see that the phone seems to work, but I can't go further than the welcome screen.
youtu.be/nEN1g7jY9m8
Thank you very much !
Click to expand...
Click to collapse
I think you fried your digitizer by flashing the wrong bootloader, The digitizer fried because I7100 digitizer uses a higher voltage than I9305. When the I7100 kernel was flashed, higher voltage was given to the digitizer. Somebody else may have a better solution but for me the only way to repair it is to flash to stock and replace the digitizer.
See this video https://www.youtube.com/watch?v=oMG-_26NgXM

LucasBass said:
I think you fried your digitizer by flashing the wrong bootloader, The digitizer fried because I7100 digitizer uses a higher voltage than I9305. When the I7100 kernel was flashed, higher voltage was given to the digitizer. Somebody else may have a better solution but for me the only way to repair it is to flash to stock and replace the digitizer.
Click to expand...
Click to collapse
Hi Lucas,
many thanks for your advice. I wan't aware of this different voltage. Too bad.
So, I've just ordered a new digitizer+screen, 66 euros on ebay. I hope it'll help !
thank you

flyjodel said:
Hi Lucas,
many thanks for your advice. I wan't aware of this different voltage. Too bad.
So, I've just ordered a new digitizer+screen, 66 euros on ebay. I hope it'll help !
thank you
Click to expand...
Click to collapse
it worked. I changed the package LCD+touch+frontscreen, very easy to do and my phone worked again in less than 15 minutes.

Good to know. ?

flyjodel said:
it worked. I changed the package LCD+touch+frontscreen, very easy to do and my phone worked again in less than 15 minutes.
Click to expand...
Click to collapse
I'm glad it worked :good:, double check before you flash something into your phone now.

LucasBass said:
I'm glad it worked :good:, double check before you flash something into your phone now.
Click to expand...
Click to collapse
Thx also from me for the hint

Related

[Q] Xperia T, same screen problem as X8, X10 and so on

Hi
Quick question. I don't know if anyone experienced that with Xperia T. I seem to have the same problem with it as with previous X8 and X10. Screen stays blank after switching on. Just backlight comes on but nothing else. Touch panel still responds as it should but no information visible phone is kinda useless. Just wondered if anyone knows how to fix this. Would it be hardware problem which seems to be going on for quite a while then in sonys mobiles or is it just software glitch? I would buy new screen but not sure if this will fix it.
Phone is updated to latest available firmaware. Done it yesterday with SUS.
Thanks
quban said:
Hi
Quick question. I don't know if anyone experienced that with Xperia T. I seem to have the same problem with it as with previous X8 and X10. Screen stays blank after switching on. Just backlight comes on but nothing else. Touch panel still responds as it should but no information visible phone is kinda useless. Just wondered if anyone knows how to fix this. Would it be hardware problem which seems to be going on for quite a while then in sonys mobiles or is it just software glitch? I would buy new screen but not sure if this will fix it.
Phone is updated to latest available firmaware. Done it yesterday with SUS.
Thanks
Click to expand...
Click to collapse
First I have heard of this probelm, so it sounds like just you.
Use PCCompanion to fix phone.
HAve you flashed anything to the phone, have you rooted it, have you unlocked bootloader.....
gregbradley said:
First I have heard of this probelm, so it sounds like just you.
Use PCCompanion to fix phone.
HAve you flashed anything to the phone, have you rooted it, have you unlocked bootloader.....
Click to expand...
Click to collapse
PC companion stops half way through the process. I've used the other standalone sonys update service to upgrade the phone which has done it no problem but still nothing visible on screen. Only brightens up slightly when switched on but nothing whatsoever visible.
gregbradley said:
HAve you flashed anything to the phone, have you rooted it, have you unlocked bootloader.....
Click to expand...
Click to collapse
quban said:
PC companion stops half way through the process. I've used the other standalone sonys update service to upgrade the phone which has done it no problem but still nothing visible on screen. Only brightens up slightly when switched on but nothing whatsoever visible.
Click to expand...
Click to collapse
I ask again...
gregbradley said:
HAve you flashed anything to the phone, have you rooted it, have you unlocked bootloader.....
Click to expand...
Click to collapse
gregbradley said:
I ask again...
Click to expand...
Click to collapse
Hi
Sorry, forgot to add earlier. No, nothing was done. No bootloader unlocking, no rooting, no other flashing. It just happened when I switched it on couple of days ago. I did have same/similar problem with X10 some time ago but along with just backlight on the screen (nothing else) but phone was in boot loop at the same time. This one just stays on for whatever time you want it and you can hear sounds and feel vibrating when using touch panel. Just trying to determine if it's something simple like faulty lcd (not cheap at all thoguh) or even if I splash out for a new lcd it will not help.
If you have not flashed anything, take it back to the shop for a new one
Sent from the future on my Star Trek communicator.
Sent from my LT30p using XDA premium.
gregbradley said:
If you have not flashed anything, take it back to the shop for a new one
Sent from the future on my Star Trek communicator.
Sent from my LT30p using XDA premium.
Click to expand...
Click to collapse
Not an option. Will have to keep searching for solution. Thanks for trying.
Same problem
quban said:
Not an option. Will have to keep searching for solution. Thanks for trying.
Click to expand...
Click to collapse
Hello, my girlfriend's phone is having the same problem, i can hear the sounds when i slide my fingers over the screen, i can take pictures with the dedicated button, the VolUp and VolDown buttons are working because i hear the beeping, but it's not showing anything on the screen, have you solved this issue? thank you :crying:
guilleglad said:
Hello, my girlfriend's phone is having the same problem, i can hear the sounds when i slide my fingers over the screen, i can take pictures with the dedicated button, the VolUp and VolDown buttons are working because i hear the beeping, but it's not showing anything on the screen, have you solved this issue? thank you :crying:
Click to expand...
Click to collapse
Hi
Yes I did. Fitted new screen! Only £160 pretty much the same as new phone now.
Was your phone damaged in any way (spilled water on it, dropped it)?
quban said:
Hi
Yes I did. Fitted new screen! Only £160 pretty much the same as new phone now.
Was your phone damaged in any way (spilled water on it, dropped it)?
Click to expand...
Click to collapse
No man, she just was charging it up, then she plugged it out, and after that it was working but with the screen off , so is it a hardware problem and not software problem?
guilleglad said:
No man, she just was charging it up, then she plugged it out, and after that it was working but with the screen off , so is it a hardware problem and not software problem?
Click to expand...
Click to collapse
In my case was hardware. In yours might be not. I'm not that much of an expert so my only suggestion would be to do hard reset. Did you try that? Hold power button for about 15-20 sec.
quban said:
In my case was hardware. In yours might be not. I'm not that much of an expert so my only suggestion would be to do hard reset. Did you try that? Hold power button for about 15-20 sec.
Click to expand...
Click to collapse
I just have reinstalled JB Stock ROM and nothing, the Display is death, the weird thing is the Digitizer works, i can even hear when i touch the buttons, anyway thank you.
Would it be strange to suggest you should contact Sony for warranty?
Sent from my LT30p using xda app-developers app

[Q] Touch screen not responding in the middle

My Incredible S has a touch screen fault. There is a area in the middle of the screen that does not respond to touch - see attachment.
I have fitted a new digitizer screen thinking that would cure the fault, but unfortunately the problem still remains.
Does anyone know what causes this and is there a solution?
ludemon said:
My Incredible S has a touch screen fault. There is a area in the middle of the screen that does not respond to touch - see attachment.
I have fitted a new digitizer screen thinking that would cure the fault, but unfortunately the problem still remains.
Does anyone know what causes this and is there a solution?
Click to expand...
Click to collapse
hey
i had the same problem except that my UNTOUCHABLE part was horizontal
anyways;
i read on several pages on net that digitizer needs to be fixed
but i asked an expert at service center and i was told that i need to replace a touchpad and screen both NOT the digitizer
i did it in INR2000 and now my INCs runs flawlessly and smoothly
prunzzz said:
hey
i had the same problem except that my UNTOUCHABLE part was horizontal
anyways;
i read on several pages on net that digitizer needs to be fixed
but i asked an expert at service center and i was told that i need to replace a touchpad and screen both NOT the digitizer
i did it in INR2000 and now my INCs runs flawlessly and smoothly
Click to expand...
Click to collapse
Thank you prunzzz for your response. I was wondering if replacing the lcd/digitizer assembly was the answer and now you have confirmed it I will go ahead and order one. :good:
ludemon said:
Thank you prunzzz for your response. I was wondering if replacing the lcd/digitizer assembly was the answer and now you have confirmed it I will go ahead and order one. :good:
Click to expand...
Click to collapse
hey please hit thanks rather than posting it!!
you know;thanks meter matters
best wishes for a 'healthy' phone!!
prunzzz said:
hey
i had the same problem except that my UNTOUCHABLE part was horizontal
anyways;
i read on several pages on net that digitizer needs to be fixed
but i asked an expert at service center and i was told that i need to replace a touchpad and screen both NOT the digitizer
i did it in INR2000 and now my INCs runs flawlessly and smoothly
Click to expand...
Click to collapse
Hello!
I am having the exact same issue (middle portion of touch-screen not working - horizontally) I was looking for a solution, and found your helpful post. Thanks added, can you please tell me what all did you replace? Just the digitizer?
Same prob as yours
prunzzz said:
hey
i had the same problem except that my UNTOUCHABLE part was horizontal
anyways;
i read on several pages on net that digitizer needs to be fixed
but i asked an expert at service center and i was told that i need to replace a touchpad and screen both NOT the digitizer
i did it in INR2000 and now my INCs runs flawlessly and smoothly
Click to expand...
Click to collapse
Brother I too have the same problem but I just bought and replaced the digitizer worth 1500 INR, Still the problem persists. I wanted to know what do u mean by saying "touch pad" ? Is it the digitizer ?
I am sorry if its a silly question

[Q] Unable to swipe down the statusbar

I've been having problems with the sensitivity of the top 2mm of my phone's screen. I don't remember when it started but I think it was around a couple of months ago.
Before, it was only difficult for me to swipe the notification bar down, but now, I can no longer swipe it down unless I rotate the screen.
I don't remember how or exactly when it started, but I remember that I was using ARHD 70.0, then I updated to 71.1 in attempt to fix it, but it only worked for a while but it came back again. I also tried other roms such as MaximusHD and Eragon but still the same. I also tried rebooting to safe mode but still the same. I also used both stock and elemental sense kernels.
I updated my firmware back then to 6.06 and now to 6.07 but still nothing. I haven't tried downgrading yet though.
I tried using the line draw test and the result is found below.
Does anyone know how to fix this? I already searched xda and google but i found no solution to my problem.
It could be a hardware related issue. If it's still under warranty revert it to stock and re-lock the bootloader and just send it back.
Kahun said:
It could be a hardware related issue. If it's still under warranty revert it to stock and re-lock the bootloader and just send it back.
Click to expand...
Click to collapse
It's not under warranty anymore.
jzerman said:
It's not under warranty anymore.
Click to expand...
Click to collapse
Has your device been dropped or been water damaged? The digitizer connection from the mb could have became a bit loose.
*Edit*
I have read on a forum for the HTC One X which seems to have a similar issue to yours where a part of the screen is unresponsive. Someone suggested to clean the connector.
Kahun said:
Has your device been dropped or been water damaged? The digitizer connection from the mb could have became a bit loose.
*Edit*
I have read on a forum for the HTC One X which seems to have a similar issue to yours where a part of the screen is unresponsive. Someone suggested to clean the connector.
Click to expand...
Click to collapse
I dropped it a few times while in a case and only around a feet at most. It never been water damaged, hopefully never will.
I see, I'll look for it there, though I'm not sure how to clean the connector. Thanks!
jzerman said:
I dropped it a few times while in a case and only around a feet at most. It never been water damaged, hopefully never will.
I see, I'll look for it there, though I'm not sure how to clean the connector. Thanks!
Click to expand...
Click to collapse
Just clean the end of it with some sort of strong spirit.
Kahun said:
Just clean the end of it with some sort of strong spirit.
Click to expand...
Click to collapse
Tried cleaning it but still the same, i used alcohol because some say that that's good enough..
jzerman said:
Tried cleaning it but still the same, i used alcohol because some say that that's good enough..
Click to expand...
Click to collapse
What launcher are you using?
Kahun said:
What launcher are you using?
Click to expand...
Click to collapse
Just the stock sense/blinkfeed launcher. I also tried smart launcher but still the same.
jzerman said:
Just the stock sense/blinkfeed launcher. I also tried smart launcher but still the same.
Click to expand...
Click to collapse
I did some more research about it and people are saying it is a digitizer issue. So replacing the digitizer should fix it, but you will need to buy the lcd and digitizer together as its nearly impossible to replace them separate from eachother.
Quote from androidcentral
It's definitely a hardware issue. I have been dealing with the same issue for about 6 months now. When I try to swipe down to bring up the notification bar I get absolutely no feedback . If I give it a smack with my palm near the top corners I can often times get it to start working again. However, it's usually short lived.
Click to expand...
Click to collapse
Kahun said:
I did some more research about it and people are saying it is a digitizer issue. So replacing the digitizer should fix it, but you will need to buy the lcd and digitizer together as its nearly impossible to replace them separate from eachother.
Quote from androidcentral
Click to expand...
Click to collapse
I see. Thank you very much for the help. I think I'll just send this to the service center when I get the chance. I will probably ask them to fix the red tinted camera as well. I just hope it won't be too expensive.
You have a dead spot. Sorry kid. If updating the OS still gives you the funk, you need a new screen.
Sent from my iPad using Tapatalk
jzerman said:
I see. Thank you very much for the help. I think I'll just send this to the service center when I get the chance. I will probably ask them to fix the red tinted camera as well. I just hope it won't be too expensive.
Click to expand...
Click to collapse
You could do it yourself and save a bit of money if you know what your doing. There are tutorials on YouTube.
Alright, the weird thing is, it started working again :| i didn't do aything :|

Xiaomi Mi5 motherboard problem?

Hello,
I have two dead Mi5 smartphones and cannot find out why.
Fastboot, recovery not working, cannot charge, no LED lights. In few words - totally dead. I tried method with checkpoints on motherboard and had successfully flashed official ROM but result was same - dead.
Any one has any ideas whats the problem? I have changed battery from working model but nothing so it should be something with motherboard. But what?
U can solve your problem
Read this(3rd post)
https://forum.xda-developers.com/mi-5/help/bricked-mi5-t3528810
Keyvannn said:
U can solve your problem
Read this(3rd post)
https://forum.xda-developers.com/mi-5/help/bricked-mi5-t3528810
Click to expand...
Click to collapse
not a solution, as I did it already twice, after a week or two you need to do the same. Probably the only option is to change the motherboard.
Shivver said:
not a solution, as I did it already twice, after a week or two you need to do the same. Probably the only option is to change the motherboard.
Click to expand...
Click to collapse
That tutorial helped You? I want to find out what's the reason of this problem.
I have the same problem, did u had solved it?
Me too have the same problem, but it occurred when my phone's power button was accidentally pressed for a long time, I showed it in service center, but they told me to change the motherboard. If anyone knows about this please help me, because I can't afford to buy a motherboard right now.
Rajburundkar said:
Me too have the same problem, but it occurred when my phone's power button was accidentally pressed for a long time, I showed it in service center, but they told me to change the motherboard. If anyone knows about this please help me, because I can't afford to buy a motherboard right now.
Click to expand...
Click to collapse
Hello i had same problem with phone. Totally dead, then i read on forum that it is probably pmi8994 chip on motherboard that was defected. I order that chip from aliexpress( must know what version is chip on your phone). Mine was pmi8994 002. I paid 8$ on aliexpress for two of them(you need only one) and 35$ for replacement. After replacement it come alive and working fine more than half year. I hope this will help.
brijacX said:
Hello i had same problem with phone. Totally dead, then i read on forum that it is probably pmi8994 chip on motherboard that was defected. I order that chip from aliexpress( must know what version is chip on your phone). Mine was pmi8994 002. I paid 8$ on aliexpress for two of them(you need only one) and 35$ for replacement. After replacement it come alive and working fine more than half year. I hope this will help.
Click to expand...
Click to collapse
How did you know that was your problem?
xaametz said:
How did you know that was your problem?
Click to expand...
Click to collapse
It was suddenly power off and didn't want to turn on. I put it on charger (before failure battery was around 70%), but it didn't power on and notification light for charging was very dim and blinking. Then i check my domestic forum and got solution from one user who had same problem.
brijacX said:
It was suddenly power off and didn't want to turn on. I put it on charger (before failure battery was around 70%), but it didn't power on and notification light for charging was very dim and blinking. Then i check my domestic forum and got solution from one user who had same problem.
Click to expand...
Click to collapse
Thank you. I think I have the same problem.
Enviado desde mi Moto E mediante Tapatalk
Same Problem with me
Try this
No solution sound
brhnahmad05 said:
Try this
Click to expand...
Click to collapse
Hi! thanks but not fix sound speaker
Hi try to do as in this video.
It worked for me after dropping my phone in water.
Hope it will help you!?
have u solved the problem.
lucosius said:
hello,
i have two dead mi5 smartphones and cannot find out why.
Fastboot, recovery not working, cannot charge, no led lights. In few words - totally dead. I tried method with checkpoints on motherboard and had successfully flashed official rom but result was same - dead.
Any one has any ideas whats the problem? I have changed battery from working model but nothing so it should be something with motherboard. But what?
Click to expand...
Click to collapse
hello!
Greetings of the day!
I am also facing the same problem , have u fixed it. If yes then please share the solution urgent need.
Thanks in advance
PMI9884 just changed and my Mi5 is working again! It was totally bricked, only faint glow of charging light after holding it on charge several hours.
Touch not responding, problem bigger than LCD
brijacX said:
Hello i had same problem with phone. Totally dead, then i read on forum that it is probably pmi8994 chip on motherboard that was defected. I order that chip from aliexpress( must know what version is chip on your phone). Mine was pmi8994 002. I paid 8$ on aliexpress for two of them(you need only one) and 35$ for replacement. After replacement it come alive and working fine more than half year. I hope this will help.
Click to expand...
Click to collapse
I need some advise on my phone (xiaomi 5s plus) not responding to touch. i replaced the ldc but i plug it in the a wrong way and it didn't work,. even the old lcd which was working well also no more responding to touch. is it possible that i have short circuited something.. if so, how can i have that chip or what ever replaced.
juukeli said:
PMI9884 just changed and my Mi5 is working again! It was totally bricked, only faint glow of charging light after holding it on charge several hours.
Click to expand...
Click to collapse
How did you change the chip? I saw a video on Youtube that describes the procedure of changing a chip, and looks like it is definitely nothing for laymen.
yahya69 said:
How did you change the chip? I saw a video on Youtube that describes the procedure of changing a chip, and looks like it is definitely nothing for laymen.
Click to expand...
Click to collapse
Friend of mine who´s kind of expert on soldering did this. Unfortunately fix didn´t last very long and problems started occuring again shortly.
juukeli said:
Friend of mine who´s kind of expert on soldering did this. Unfortunately fix didn´t last very long and problems started occuring again shortly.
Click to expand...
Click to collapse
Thanks for your reply! Sorry to hear that it didn't help.

Touchesceen isnt working anymore

Hi there,
so for a few weeks now my touchscreen hasn't been working anymore.
Power and Volume buttons are working fine.
At first i shut my screen off again and again until i the touchscreen responded.
But since today I couldn't get my touchscreen to work.
The touchscreen also doesn't respond in TWRP Recovery.
So does this mean that my touchscreen is defect?
It never fell down the glass is not broken. The problem occurred suddenly.
I am rooted and my bootloader is also unlocked.
I am on Resurrection Remix 5.8.0 N.
Fresh Rom installs didn't help sadly.
For now I am using my phone with a mouse via USB OTG..
I hope that someone can help me out.
Thanks in advance.
Your digitalizer seems to have defect, try to give it to some repair shops to have a check.
iXaidyiu said:
Your digitalizer seems to have defect, try to give it to some repair shops to have a check.
Click to expand...
Click to collapse
Repairing will cost me about 120€- 160€.
I think that is way too much dont you think?
badflife said:
Repairing will cost me about 120€- 160€.
I think that is way too much dont you think?
Click to expand...
Click to collapse
So, buy a new phone
Sent from my Sony D6503 using XDA Labs

Categories

Resources