Related
Hi,
I've been looking at replacement housings for my PDA as it's a bit scratched and fancy getting a black one instead of grey.
I've spotted some good looking ones on eBay: http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=260078879244&fromMakeTrack=true
Anybody tried these?
If so, how are they?
Cheers,
Martin.
Just note: The 'case' mentioned is for Magician phones, i'm not sure if thats the same as that of Charmer.
i know they look the same so might be a good match?! only thing i know for sure though is that the front plate is made of metal on magicians and plastic on the charmer.
dave106 said:
i know they look the same so might be a good match?! only thing i know for sure though is that the front plate is made of metal on magicians and plastic on the charmer.
Click to expand...
Click to collapse
The Charmer and the Magician are having the same front panel, camera cover, and battery cover. BUT the middle black plastic housing that sit between the panels(as shown in the attached picture), is NOT the same(reset and microphone places exchanged):
Funnily enough, my TM MDA compact II has a metal front cover.
Same here, my Charmer has a (scratched) metal cover.
If I'm only changing the front and back panels and not the middle section do you think it's worth a shot?
univega said:
Same here, my Charmer has a (scratched) metal cover.
If I'm only changing the front and back panels and not the middle section do you think it's worth a shot?
Click to expand...
Click to collapse
yes it will fit. i made it myself.
Thanks for that, just ordered one now.
I'll post picks once it's fitted.
I'd also like to change the housing of my mda compact ii but Im not too sure whether I'd be able to do it.
Are there any step by step instructions available? and what are the possibilities of ruining all this.. Because everytime I open something im never able to put it back together properly
so anyone else replace their charmers casing? the only problem i found is with the battery cover doesnt quite slide up all the way, leaves a tiny gap. anyone know which part of the cover needs to trimming so it goes all the way up?
You need to trim the small clips at the bottom of the cover (near the headphone socket) as they're a fraction too long.
I have looked everywhere but no luck! Can someone please give clear instruction how to replace the digitizer/touch panel?
I have only found instructions how to disassemble the diamond up to the LCD stage only! But after that it does not show how to take the LCD out of the housing to expose the Digitizer.
Hope someone knows how to do it.
Thanks.
The instructions you looked at, where they from the Service Manual or another source?
one from the service manual at XDA-WiKi page and other post from http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond
but both goes up to the same stage and stop.
Yeh I've got the same service manual and it doesn't really go into any detail about how to replace the digitizer. Maybe there's another 'level' of the Service Manual for that. Only question is, where does one obtain it? Good luck replacing it - how come you're replacing it btw? Your touch screen not responding?
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
kortez said:
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
Click to expand...
Click to collapse
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Scratched screen
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
dalewinterstein said:
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
Click to expand...
Click to collapse
digitizer arround 29 USD + shipping.
not sure if LCD is available yet.
if you scratched the screen you will only need to replace the digitizer which is the actual screen you press on.
the only thing is no clear instruction how to replace it!
ammar said:
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Click to expand...
Click to collapse
Without disassembling - no, for sure.
And seeing the video - I would not suggest you to, it's quite hard, cuz it's all packed very tight.
I heard that there's glass in front of screen on diamond that sends the pressures to the real touch screen. But that maybe not true. I guess you'll have to disassemble the diamond to see what the touchscreen is on it.
Or you shoudl find the video, where you can clearly see if the touch diamond' screen have any protective glass..
Kortez,
thanks for your help, do you have link to the said video?
thanks
can't remember where I've seen. But it exists.
http://www.youtube.com/watch?v=_jY46M_NGz0
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
tape said:
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
Click to expand...
Click to collapse
We need the instruction on the replacement step, not the part.
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Adam86 said:
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Click to expand...
Click to collapse
I thought the digitizer cable can be just slot into the connector type, no? Did your digitizer come with soft ply tools? which to help on plying out the screen and digitizer i heard. I'm gathering info before placing my purchase on the digitizer... Coz its badly scratches, felt and kicked!
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Hi, could anyone of you make some pictures or a small video about how to get the display out of the body, or where exactly i need to pull the display out.
i have already dismantled my diamond, but still didnt get the display and digitizer out. When i pulled the display i think i broke it somehow, because now my display shows me only stripes...
anyway, my ordered display still didnt arrive....
if you could make a vid or some pictures, it would be very helpful.
Adam86 said:
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Click to expand...
Click to collapse
how was the soldering part? difficult? as i heard it might melt the plastic cable, no?
If i do cracked the existing digitizer, no harm i see since its already borken though.
Well, i managed to get the lcd and tocuh sceen apart, and now am stuck with the soldering part either.
the sceen has to be pushed out from the inside....the glue they used is pretty strong. and the display breaks pretty fast....
isnt there a way to connect the lcd and ts without soldering?
My touch screen stopped working on my phone, but the screen is still visible. I'm assuming it's the digitizer. I was wondering if anybody has done or tried replacing only the digitizer. Does this work, is it better just to replace both? Any suggestions? Thanks.
Save yourself the headache
Just replace the complete screen unit (lcd + digitizer).
The digitizer is held on the screen with some super strong adhesive that is nearly impossible to get off cleanly. Also, there are three (4?) thin ribbon tabs that have to be soldered to the board on the rear of the lcd. Unless you are really confident with a soldering iron, it is extremely hard to do.
I replaced my screen unit in about a half hour. Make sure you go to the wiki and find one of the excellent disassembly guides before you start.
Thanks
Thanks, that's exactly the information i needed to know. I found the fon logix video. Is it only a t6 tool i need, or do i also need a t5. I have seen conflicting info on this? Thanks again.
I got my scren unit from ebay, and it included a torx driver and a plastic case tool. I honestly can't remember what size came in the kit, because I used my own torx set. Im pretty sure its just the one size, though.
Good luck!
You might find this information interesting.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=116836
Disregard ............
i always replace only the touch screen. okay i've done it aprox 30 times. But i never broke one.
if you decide to replace only the touchscreen, there are 2 types. thus check which on you have, and i found out that sometimes reassamble, and cleaning can help.
good luck.
torx is 5 and 6, 6 for opening the back of the phone, 5 for the screen part removal of the body and opening it. you need an opening tool!!
adhesive
is there a terrible adhesive between the screen and digitizer, as the second poster mentioned? how difficult is it to deal with?
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Thanks
Thanks for all of the info, i went ahead and purchased the screen with the digitizer and tools. One thing i have noticed though is the d-pad has stopped working also, i'm using a custom rom so i'm not sure if it's just that or it's something else. i will prob re-image after i replace screen.
Abel2007 said:
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Click to expand...
Click to collapse
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
i would love to know this too because i have to also replace my digitizer!
drokkon said:
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
Click to expand...
Click to collapse
I used rtv gasket maker the transparent blue one worked well.
you can find it in automotive section. Actually any silcone will work.
also can use double sided tape but needs to be very thin
I've already changing my digitizer, but it doesn't seem to work. So I've change the whole part. cost me $20 more on ebay.
my advice is to change the whole package with the lcd too.
Ok so i have a cracked digitizer...
I am going to replace it myself, however this phone is obviously not a straight forward repair.
Anyone have any personal experience replacing the digitizer on this phone? I have seen the youtube videos and read the xda.cn chinese breakdown, just looking for some personal input on the process if someone has one.
Also what will i need to rebuilt it? Do i need double sided tape etc. Thanks
80 views and no ones ever had experience with this?
i replaced it on 2 hd7 phones.
its a real pain to get it off because the glue tape they use goes all the way around, and its strong stuff.
you need to take apart the entire phone to get to the ribbon cable where the digitizer plugs in, so just look for some youtube videos of a tear down and watch carefully.
honestly the hardest part for me was getting the screen and digitizer clean of fingerprints and tiny broken glass pieces without messing up the screen, while keeping the double sided tape i put on in place and intact.
just take your time and everything will go smoothly.
-edit- yes you will need some double sided tape because when you take the digitizer off the sticky layer of the tape goes with it, the rest of the tape stays on the screen and is impossible to get off without damaging your screen so you have to apply new tape over it.
i used some thin scotch brand double sided tape and i cut it into long narrow strips with a razor using my old digitizer as a cutting board, the same width as the original tape.
Hi mate appreciate the advice in my thread on the HD7 replacement.
I managed to get the digitizer out, however on replacing the new one i have a problem..
You know the old digitizer has three plastic prongs, on the buttons at the bottom, search etc.
Am i rigth in saying they need to be transferred to the new digitizer? As i can't see how they fit on the LCD when stuck to the digitizer? It raises the digitizer a little, unless they hand off the edge of the lcd?
Thanks
CraiGDaniel said:
Hi mate appreciate the advice in my thread on the HD7 replacement.
I managed to get the digitizer out, however on replacing the new one i have a problem..
You know the old digitizer has three plastic prongs, on the buttons at the bottom, search etc.
Am i rigth in saying they need to be transferred to the new digitizer? As i can't see how they fit on the LCD when stuck to the digitizer? It raises the digitizer a little, unless they hand off the edge of the lcd?
Thanks
Click to expand...
Click to collapse
Those are nothing more than spacers. I have replaced two digitizers without them. As long as you get some good 3M double sided in that area there is no problems.
StevetotheH said:
Those are nothing more than spacers. I have replaced two digitizers without them. As long as you get some good 3M double sided in that area there is no problems.
Click to expand...
Click to collapse
um no they arent spacers...they are what directs the light to the 3 bottom keys. they are there for a reason so i recommend using them... ... now you are spot on with the 3m tape as it is the tape needed to do this whole job properly... the scotch crap is not made for this and WILL NOT HOLD UP NOR SEAL PROPERLY>>>
and for the person who said to put the tape over the old.... not a good idea... it can be removed and new should be used to replace the old..
sorry but i do this daily for a living so i do have a clue about this... just trying to help make it a successful repair and not one that ends up in my shop after the home repair failed and it damaged more than just the screen.....
Hi guys.
I've dropped my xt1068 on a floor and the glass got cracked although the screen works perfectly (no damaged parts at all). I've buyed the replacement glass from ebay (this one http://www.ebay.com/itm/Black-Front...244?pt=LH_DefaultDomain_0&hash=item566c04b4ec ).
My question is, have anyone passed through this situation? Is there any way to replace it without damaging the screen? I heard that glass is glued to the digitalizer screen and I'm worried.
Any thoughts?
Antique_Angel said:
Hi guys.
I've dropped my xt1068 on a floor and the glass got cracked although the screen works perfectly (no damaged parts at all). I've buyed the replacement glass from ebay (this one http://www.ebay.com/itm/Black-Front...244?pt=LH_DefaultDomain_0&hash=item566c04b4ec ).
My question is, have anyone passed through this situation? Is there any way to replace it without damaging the screen? I heard that glass is glued to the digitalizer screen and I'm worried.
Any thoughts?
Click to expand...
Click to collapse
I don't think it is glued, but if it is try putting some light heat on it, not real hot though. The glass is meant to be replaced. I'm guessing you have the disassemble instructions.
https://www.ifixit.com/Guide/Motorola+Moto+G+2nd+gen.+2014+LCD+screen+Replacement/36180
Tel864 said:
I don't think it is glued, but if it is try putting some light heat on it, not real hot though. The glass is meant to be replaced. I'm guessing you have the disassemble instructions.
https://www.ifixit.com/Guide/Motorola+Moto+G+2nd+gen.+2014+LCD+screen+Replacement/36180
Click to expand...
Click to collapse
Thanks. But the video shows how to replace the whole screen, I just bought the glass (which I need to replace). I've little concerned about separating glass from screen.
And the only tutorial I found is for samsung galaxy s4.
Antique_Angel said:
Thanks. But the video shows how to replace the whole screen, I just bought the glass (which I need to replace). I've little concerned about separating glass from screen.
And the only tutorial I found is for samsung galaxy s4.
Click to expand...
Click to collapse
I'd give it a shot. The worst you could do is have to put it back together with the broken glass. It's a pretty straightforward job taking it apart. Just be careful with the pins on the cables you unplug.
Tel864 said:
I'd give it a shot. The worst you could do is have to put it back together with the broken glass. It's a pretty straightforward job taking it apart. Just be careful with the pins on the cables you unplug.
Click to expand...
Click to collapse
Thanks!
I've also bought a uv glue to glue it better. After the process, I'll share the results.