I've had my L90 for about two months now, and I'm happy to have it after owning an S2 which has had a faulty USB port and crashed almost daily. The only problem with the L90 was the small internal memory. To remedy this, I bought a SanDisk 32 GB MicroSD, which arrived yesterday. It worked well, the first thing I did was put the first 5 seasons of Adventure Time onto the SD card (~13 GB of .mp4 video) in about an hour and the files played fine in MX Player. However, some problems began to arise after this.
The phone would say that it's in MTP mode, and my computer would show that it was connected, but opening it in Explorer showed me a blank window. Keep in mind that these problems began after mounting the SD card. In addition to this, any attempt to move music would end in the middle of the process because the phone would "disconnect", and any attempt to move an .mp4 file would come up with an error saying the device "didn't support" that file, despite being able to play them previously.
I have tried multiple USB ports on my computer, rebooted my phone, installed the LG drivers (which I feel haven't done anything, as they don't show up anywhere), and nothing seems to work. If anyone could help me out with this, it'd be greatly appreciated.
Update on situation:
The phone's problem now is that it will show up in My Computer, but then disappears after a few seconds, as though it has been disconnected, yet it's still plugged in and charging.
folieadeux said:
Update on situation:
The phone's problem now is that it will show up in My Computer, but then disappears after a few seconds, as though it has been disconnected, yet it's still plugged in and charging.
Click to expand...
Click to collapse
that my friend i fixed pretty easily.... all though the worst way... if you have cutom recovery wipe the cache and dalvik-cache if not then factory reset
demonslayer12349 said:
that my friend i fixed pretty easily.... all though the worst way... if you have cutom recovery wipe the cache and dalvik-cache if not then factory reset
Click to expand...
Click to collapse
So I should just format the SD card and that should work?
folieadeux said:
So I should just format the SD card and that should work?
Click to expand...
Click to collapse
if you have custom recovery factory reset
demonslayer12349 said:
if you have custom recovery factory reset
Click to expand...
Click to collapse
I don't have a custom recovery installed.
I'd suggest uninstalling all LG drivers. Reboot your PC and then run the driver installation program again. DO NOT connect your device to the PC just yet. Reboot PC once more. After PC starts, connect your device in "Charge phone" mode. Let the drivers install. From the "PC connection -> Select USB connection method" screen on the device, select "Media sync ( MTP )" and let the drivers install. Do the same for the remaining two connection methods. Once all drivers are installed, just for sanity, reboot PC one last time.
If that method doesn't work, then a factory reset may need to be done. This can be done in one of two ways.
1) With device booted :: Settings -> Backup & reset :: select Factory data reset
2) See this post for instructions on how to perform a factory reset with key combos.
shinobisoft said:
I'd suggest uninstalling all LG drivers. Reboot your PC and then run the driver installation program again. DO NOT connect your device to the PC just yet. Reboot PC once more. After PC starts, connect your device in "Charge phone" mode. Let the drivers install. From the "PC connection -> Select USB connection method" screen on the device, select "Media sync ( MTP )" and let the drivers install. Do the same for the remaining two connection methods. Once all drivers are installed, just for sanity, reboot PC one last time.
Click to expand...
Click to collapse
I've done everything up until installing the drivers from the phone. When it's first plugged in in "Charge Phone" mode, should I hit the button in the top right to install the PC software? Or should I go straight to the other drivers? I'm asking because when I plugged it in with "Charge Phone" mode on, nothing installed.
folieadeux said:
I've done everything up until installing the drivers from the phone. When it's first plugged in in "Charge Phone" mode, should I hit the button in the top right to install the PC software? Or should I go straight to the other drivers? I'm asking because when I plugged it in with "Charge Phone" mode on, nothing installed.
Click to expand...
Click to collapse
Yes, if you don't have another LG driver installer package.
shinobisoft said:
Yes, if you don't have another LG driver installer package.
Click to expand...
Click to collapse
I did everything you said, installed drivers, reset my computer and phone, and the problem persisted, it showed up, and then the window closed and nothing showed up. Will I have to factory reset it or is there anything else I could do?
folieadeux said:
I did everything you said, installed drivers, reset my computer and phone, and the problem persisted, it showed up, and then the window closed and nothing showed up. Will I have to factory reset it or is there anything else I could do?
Click to expand...
Click to collapse
With fresh drivers and you're still having issues then I'd say it can be one of 3 things:
1) Bad MTP driver on Windows. Hard disk fragmentation can cause issues like this. Try running Defrag on the Windows installation drive. Usually ( C: )
2) #1 didn't fix it? Try uninstalling and reinstalling Windows Media Player. MTP only works with Windows XP 32 bit and Windows Media Player 11, and newer 32 and 64 bit Windows versions with Windows Media Player installed.
3) #1 and #2 didn't work??? Possibly a hardware issue on the device.
shinobisoft said:
With fresh drivers and you're still having issues then I'd say it can be one of 3 things:
1) Bad MTP driver on Windows. Hard disk fragmentation can cause issues like this. Try running Defrag on the Windows installation drive. Usually ( C: )
2) #1 didn't fix it? Try uninstalling and reinstalling Windows Media Player. MTP only works with Windows XP 32 bit and Windows Media Player 11, and newer 32 and 64 bit Windows versions with Windows Media Player installed.
3) #1 and #2 didn't work??? Possibly a hardware issue on the device.
Click to expand...
Click to collapse
Should I install the MTP toolkit? Also, I'm running a defrag on my C: drive, and I have Windows 7 64-bit, and I'm not totally sure on how to uninstall and reinstall WMP. If none of this works, I'll just factory reset it and hope it solves it.
you are using lockscreen lock or something????
sometimes lockscreen lock can make device disappear like you said...
k2wl said:
you are using lockscreen lock or something????
sometimes lockscreen lock can make device disappear like you said...
Click to expand...
Click to collapse
I have a lockscreen with a pattern, if that's what you're asking.
Related
I've added a few apps to my S3 and altered a few things on my PC and now I can't connect via mtp or ptp. It goes through the usual "installing drivers" and then fails. I've tried pulling the battery and removing the sim and micro sd card then putting everything back. Tried it without the card (currently having to transfer files via a card reader so - at least the card's fine) but to no avail.
I've had a go at uninstalling the drivers through the device manager, rebooting and scanning for hardware changes. I've tried downloading the drivers without kies but it didnt work out (I cant remember the site or the url, but ended up with the following file SAMSUNG_USB_Driver_for_Mobile_Phones) It didn't auto install but even when I tried to point Windows to the folder on my C drive, nothing.
I've spent a couple of hours trawling the net including on here and tried all sorts.
I'm rooted, using the stock 4.1.2 ROM with Windows 7.
I can't use Kies as when it was installed the first time it wrecked all my Synctoy sync's so I really could do with another option please guys.
Dial *#7284# on your phone to access PhoneUtil and select 'Qualcomm USB Settings' at the bottom.
Now select 'MTP + ADB' and press 'OK' to return to the previous screen. Now press your 'Back' key to exit PhoneUtil. Your phone is now back to default USB operation.
Raistlin1158 said:
Dial *#7284# on your phone to access PhoneUtil and select 'Qualcomm USB Settings' at the bottom.
Now select 'MTP + ADB' and press 'OK' to return to the previous screen. Now press your 'Back' key to exit PhoneUtil. Your phone is now back to default USB operation.
Click to expand...
Click to collapse
Thanks for the quick reply.I did that and it was set to mtp + adb...
When I then connected it it tried installing the driver and I got..
Driver device software was not installed.
Please consult with your device manufacturer for assistance getting this device installed
MTP USB Device X Failed
I tried updating the MTP drivers again from device manager but this time got
Windows encountered a problem installing the driver software for your device
Windows found driver software for your device but encountered an error while attempting to install it.
SAMSUNG Mobile MPT Device
This device cannot start (code 10)
From what I'm reading it's a computer error not the phone. Can anyone suggest a new set of drivers to download (that doesnt involve Kies) as I've had issues with picking up harmful software from random sites when I've been struggling to find drivers.
I tried using the suggestion at the bottom of here r.e.Portable Devices and deleting the Upperfilters string Link but also to no avail.
Oh, and yes I've tried different ports and cables.
Well that's me done for the evening! I've tried everything mentioned in this thread including updating java and windows media player and all the afformentioned stuff but still no dice.
Could it be the actual drivers or a random windows 7 setting that I haven't yet tweaked since my clean install of windows??
http://d-h.st/YpV
Here are the correct drivers, install then reboot your pc.
Raistlin1158 said:
Go here for drivers.
---------- Post added at 01:00 AM ---------- Previous post was at 12:57 AM ----------
http://d-h.st/YpV
Here sre the correct drivers, install then reboot your pc.
Click to expand...
Click to collapse
Sorry,I know I'm tired but I can't see a link on your post...
Highlighted in red
The newer drivers don't really wwork with the 9305 so find some older drivers. That works for me
Sent from my GT-I9305 using xda app-developers app
Thanks for the tip.any suggestions as to where I can download these older drivers? I'll try the previously mentioned ones first, but I'm starting to think it might be the drivers themselves
woldranger said:
Thanks for the tip.any suggestions as to where I can download these older drivers? I'll try the previously mentioned ones first, but I'm starting to think it might be the drivers themselves
Click to expand...
Click to collapse
The ones I posted work fine on my 9305 so you shouldn't have any issues and as you can see from the site they are nearly a year old.
Try them what have you got to loose, if they don't work you are no worse off
Raistlin1158 said:
The ones I posted work fine on my 9305 so you shouldn't have any issues and as you can see from the site they are nearly a year old.
Try them what have you got to loose, if they don't work you are no worse off
Click to expand...
Click to collapse
Cheers, yeah, I was going to try them but I wasn't at my pc at the time I wrote that. I've downloaded the exe package but now it seems there are still drivers to uninstall - I uninstalled the drivers through device manager and went into my C drive and removed the SAMSUNG folder with the USB drivers in it. I'll restart the pc and hope that helps with the removal....
woldranger said:
I've added a few apps to my S3 and altered a few things on my PC and now I can't connect via mtp or ptp. It goes through the usual "installing drivers" and then fails. I've tried pulling the battery and removing the sim and micro sd card then putting everything back. Tried it without the card (currently having to transfer files via a card reader so - at least the card's fine) but to no avail.
I've had a go at uninstalling the drivers through the device manager, rebooting and scanning for hardware changes. I've tried downloading the drivers without kies but it didnt work out (I cant remember the site or the url, but ended up with the following file SAMSUNG_USB_Driver_for_Mobile_Phones) It didn't auto install but even when I tried to point Windows to the folder on my C drive, nothing.
I've spent a couple of hours trawling the net including on here and tried all sorts.
I'm rooted, using the stock 4.1.2 ROM with Windows 7.
I can't use Kies as when it was installed the first time it wrecked all my Synctoy sync's so I really could do with another option please guys.
Click to expand...
Click to collapse
Having the same problem. but I am on 4.3 rom using carbon rom a few days then transferred to pac man rom. My cellphone is not detected in my computer but it is being detected in the safely remove usb options. I tried to use a usb otg cable and a flash disk. No notification is seen on my phone but I can access the files on the flash disk (using usb otg cable) in the file manager. Tried the *#7284# but error occurs and says connection problem or invalid MMI code. I found that MTP udb device says failed
Raistlin1158 said:
The ones I posted work fine on my 9305 so you shouldn't have any issues and as you can see from the site they are nearly a year old.
Try them what have you got to loose, if they don't work you are no worse off
Click to expand...
Click to collapse
It made no difference whatsoever. I used a utility to check for an remove the samsung drivers (USBDeview) as well as uninstalling through device manager and removing with windows "products and features" but even then, when I tried installing the new drivers it mentioned previous drivers. I restarted after each stage of the process.
I've even tried connecting it in download mode and it shows in device manager.
Could there be some remnant of the software I used to root that phone that might be causing the issue??
I'm due to leave the country in 5 days and have loads of things to sort (also have a family member going into hospital for major surgery tomorrow) so I can't just devote all my time to this - but I need to at least know that it's not the phone (I dont have another win 7 computer to try it on).
woldranger said:
It made no difference whatsoever. I used a utility to check for an remove the samsung drivers (USBDeview) as well as uninstalling through device manager and removing with windows "products and features" but even then, when I tried installing the new drivers it mentioned previous drivers. I restarted after each stage of the process.
I've even tried connecting it in download mode and it shows in device manager.
Could there be some remnant of the software I used to root that phone that might be causing the issue??
I'm due to leave the country in 5 days and have loads of things to sort (also have a family member going into hospital for major surgery tomorrow) so I can't just devote all my time to this - but I need to at least know that it's not the phone (I dont have another win 7 computer to try it on).
Click to expand...
Click to collapse
Just got the same problem. But my problem is already solved. Just flash a new rom. In my instance, I flash ripper rom
So, everytime I connect my HTC One to the computer, the computer never recognizes the internal storage. I must go to "Control Panel" > "View devices and printers" (category view under "Hardware and Sound") > right click on MTP (and do the troubleshoot thing to apply fix)
to make it work.
Once I do that, then the internal storage gets recognized. If I reconnect with the comp still on afterwards, it will show up, but when I turn off comp or restart, I must do the troubleshoot thing again. I think it's a driver issue. Any suggestions? I'm running Windows 7 64-bit. I am on ViperOne 2.7.0, S-Off, Super-CID. Although, I don't think it's an issue with rom. I've even used stock rom and same thing happens.
EDIT: It is a driver issue, but why do I have to reinstall it every time the computer shuts down or restarts?
theBhav007 said:
So, everytime I connect my HTC One to the computer, the computer never recognizes the internal storage. I must go to "Control Panel" > "View devices and printers" (category view under "Hardware and Sound") > right click on MTP (and do the troubleshoot thing to apply fix)
to make it work.
Once I do that, then the internal storage gets recognized. If I reconnect with the comp still on afterwards, it will show up, but when I turn off comp or restart, I must do the troubleshoot thing again. I think it's a driver issue. Any suggestions? I'm running Windows 7 64-bit. I am on ViperOne 2.7.0, S-Off, Super-CID. Although, I don't think it's an issue with rom. I've even used stock rom and same thing happens.
EDIT: It is a driver issue, but why do I have to reinstall it every time the computer shuts down or restarts?
Click to expand...
Click to collapse
Uninstall HTC Sync and any driver you may have right now for your cellphone and install these naked drivers.
Hi everybody,
I have a 64-bit PC with Windows 7 Ultimate Service Pack 1 and a Samsung Galaxy S Advance GT-I9070 with Android 4.1.2.
I can't install a driver in order to make Windows recognize correctly the phone when I connect it via USB cable.
I've installed and uninstalled Samsung Kies many times with no results. I've also tried some Samsung driver from Windows Update with no success...
When I connect the phone, it is recognized as a MTP Device and the driver installation starts, but always ends with an error, as shown in the attached screen-shot image.
What can I do?
Thank you very very much.
Note: in another PC with WinXP I have no problems.
Firstly make sure phone can run MTP (make sure if you delete MTP releated stuff in system you won't able connect it. Re-flash with Odin) Now if you don't have problem with phone then uninstall drivers & KIES from Windows. Don't just do a uninstall clear temp files, dll files, registry entries (you can use CCleaner) then install THIS DRIVERS.
explanation
King ov Hell said:
Firstly make sure phone can run MTP (make sure if you delete MTP releated stuff in system you won't able connect it. Re-flash with Odin) Now if you don't have problem with phone then uninstall drivers & KIES from Windows. Don't just do a uninstall clear temp files, dll files, registry entries (you can use CCleaner) then install THIS DRIVERS.
Click to expand...
Click to collapse
Hello, thank you for your answer.
How can I make sure my phone can run MTP?
For the complete uninstall, is it enough to run CCleaner, uninstall Kies and then perform the Registry Cleaner in CCleaner?
Thank you
ZioAlfredo said:
Hello, thank you for your answer.
How can I make sure my phone can run MTP?
For the complete uninstall, is it enough to run CCleaner, uninstall Kies and then perform the Registry Cleaner in CCleaner?
Thank you
Click to expand...
Click to collapse
Did you root phone ? or installed a ROM or you just using it stock ?
I noticed something too; if you any have PIN or Password you have to unlock phone otherwise MTP not works. Unlock it and try too.
CCleaner will *probably* be enough but if you want to make sure go to regedit.exe and go to;
Code:
HKEY_CURRENT_USER/Software/
Then delete KIES & USB Driver stuff (don't delete system USB configs & drivers just Samsung's softwares )
EDIT: In start menu click to RUN (or whatever I don't now it's name in English, you're entering a text) Then write
Code:
%AppData%
Then delete KIES & Samsung folders and files.
I've just Updated the phone firmware from Android 2.3.6 to 4.1.2 with Samsung Kies on my WinXP PC.
I've deleted all Samsung Kies registry entries.
Now I'm going to install the driver you suggested...
Let me see results...
King ov Hell said:
Let me see results...
Click to expand...
Click to collapse
Failure... The same as always
ZioAlfredo said:
Failure... The same as always
Click to expand...
Click to collapse
...
I've also installed Windows MTP Porting Kit, but it still fails...
Any idea?..
I think it is the configuration of this PC, because in another brand new PC with Windows 7 I've installed Kies and it all went right.
ZioAlfredo said:
I've also installed Windows MTP Porting Kit, but it still fails...
Any idea?..
I think it is the configuration of this PC, because in another brand new PC with Windows 7 I've installed Kies and it all went right.
Click to expand...
Click to collapse
Have you tried to reboot phone? I lost mtp after charging phone over wall charger. Everytime I need to reboot after charging to get it connected to pc.
Sent from my GT-I9070 using Tapatalk
This may be a bit silly but is important to ask.
Was your PC connected connected to the internet while installing the drivers??
Did you unplug your phone while the drivers were being installed??
anantttt said:
This may be a bit silly but is important to ask.
Was your PC connected connected to the internet while installing the drivers??
Did you unplug your phone while the drivers were being installed??
Click to expand...
Click to collapse
Yes to all.
shut_down said:
Have you tried to reboot phone? I lost mtp after charging phone over wall charger. Everytime I need to reboot after charging to get it connected to pc.
Sent from my GT-I9070 using Tapatalk
Click to expand...
Click to collapse
I've just tried to reboot the phone before connecting it to the PC, but I get the same error (see attachments).
Last year I managed to connect the phone to this PC, but, in any case the connection got interrupted after a while (see this thread).
I don't know what to do...
I had the same problem when i formatted my PC 2 days ago. I did some trial and error and it worked.
1. Dont use any USB Hub if you are using.
2. Remove the Pattern lock or any password security etc. Go to lock screen and select 'None'. (I dont know why but windows doesn't recognise if the device is locked)
3. Have Kies installed. Even new version worked for me. I used 2.5.13043_14
4.Connect your device with the USB cable (Should have MTP option selected which is by default)
5. Windows automatically recognises now and installs the necessary files.
P.S:- Remove the security pattern, etc. It really works.
If worked then pls reply.
Hello,
I've disable any screen lock on my phone and I've connected the USB cable to another USB port (a 3.0 USB port) and Windows magically recognized correctly the device! (no Kies installed, only drivers)
Anyway, after some minutes of usage (cut-paste of files). Windows stopped recognizing the device...
If I disconnect the phone and then connect it back, Windows still recognizes it, but I have few minutes until the device stops being recognized and no file on it can be read...
See attached pictures
ZioAlfredo said:
Hello,
I've disable any screen lock on my phone and I've connected the USB cable to another USB port (a 3.0 USB port) and Windows magically recognized correctly the device! (no Kies installed, only drivers)
Anyway, after some minutes of usage (cut-paste of files). Windows stopped recognizing the device...
If I disconnect the phone and then connect it back, Windows still recognizes it, but I have few minutes until the device stops being recognized and no file on it can be read...
See attached pictures
Click to expand...
Click to collapse
Did you download newest version of drivers? I see in your screenshot it says 2012, on mine it is 2014.
Did you set Windows to gather drivers automaticaly from the internet?
shut_down said:
Did you download newest version of drivers? I see in your screenshot it says 2012, on mine it is 2014.
Did you set Windows to gather drivers automaticaly from the internet?
Click to expand...
Click to collapse
This is how my PC recognizes my phone. The driver seems to be old, but I've configured Windows for downloading drivers automatically and that is all it can do.
Today, th PC did not recognized the phone at once. Then I unmounted and mounted back the MicroSD card and the PC recognized it.
But, after few seconds of folder browsing, the PC lost the connection. I'm thinking that the problem is the SD card.
Solved!
Solved!
It was the USB cable.
I replaced it with an original one and now it works.
Thank you everybody for your effort!
Hi all,
First a quick info:
The Problem -- Nexus 6 internal storage doesn't show up when connecting to my main desktop computer.
I have had my Nexus 6 for almost a year now and since the beginning I couldn't make my main computer to recognize the phone's internal storage.
Whenever I connected the phone to another computer, the driver installed just fine and I was able to access the internal storage.
I previously had a first gen moto g and I thought the problem was because the moto g drivers were causing some mess with the Nexus so I uninstalled the old drivers and plugged my nexus so windows automatically downloaded what is shown as "Google Nexus ADB Interface" under Android device in Device manager.
I also have installed Android SDK tools in my PC since I had the Moto g and I cant remember how many times I have updated it. The Google driver is shown as installed.
The device is unlocked but not rooted.
Here comes the weird part... If I have USB debugging enabled then I can see the camera files in my PC when I choose PTP in USB configuration. However.. if I disable USB debugging then I can't even see the pictures.
I have tried selecting PTP and changing back to MTP as suggested in some threads with no luck.
I also tried turning the device off and then boot into fastboot, then plug the phone into the computer as this worked in some other computer.
This is driving me crazy, I know this is a computer related problem but I don't know what else to try.
Could you help me please?
Thanks
adrek09 said:
The Problem -- Nexus 6 internal storage doesn't show up when connecting to my main desktop computer.
Whenever I connected the phone to another computer, the driver installed just fine and I was able to access the internal storage.
Click to expand...
Click to collapse
www.wugfresh.com
Install the Nexus Root Toolkit on your PC.
In a sub directory of that kit you will find several usb drivers. Do some trial and error with those drivers.
NLBeev said:
www.wugfresh.com
Install the Nexus Root Toolkit on your PC.
In a sub directory of that kit you will find several usb drivers. Do some trial and error with those drivers.
Click to expand...
Click to collapse
Hi, thanks for the reply,
I forgot to tell that I tried that one too.
I followed the driver installation guide step by step with no luck.
Tried the recommended solution at step 3 of the guide and since it didnt work then I tried the manual installation with a couple "Bluetooth Peripheral Device" devices that are shown under Other Devices in Device manager
adrek09 said:
Hi, thanks for the reply,
I forgot to tell that I tried that one too.
I followed the driver installation guide step by step with no luck.
Click to expand...
Click to collapse
Because it works on a different PC. I assumed a driver issue.
My Suggestion is to install the driver manually.
Open the device manager.
After connecting you must see a change in the device manager. If not change USB-port and/or cable. And change on the Nexus 6 the charging
mode to data mode.
When still no 'internal storage' back to device manager and update the driver by right clicking. Try automatic and search on my computer - navigate to the drivers in NRT.
--- SOLVED see first post second page! ---
Hello XDA,
I am only able to read data on the phone when connected via USB on windows. On the phone itself I can change whatever I want ( Via ES-explorer for example) But in windows file explorer I can't. It will not tell me that I do not have proper writing rights, but instead just decides to freeze for 10 minutes everytime I try to make a file change, to eventually give me a beautiful
"windows explorer is not responding" pop-up
What I have tried :
-Rebooting,
-Reinstalling USB drivers,
-Switching USB debugging on and off,
-Reinstalling root,
-Installing the newest Oxygen OS update from February,
-used different cables (also an old micro USB with adapter) And nothing works.
This sucks because I was just trying to change my photography workflow from being Desktop based to being Android based..
Any suggestions ?
Greetings,
Thijs
www.instagram.com/thi_js
Edits: Clarify issue
i have the same problem be great to find a solution
Did you maybe noticed when this problem occurs to you? I know that one months ago it just did work. Should I reinstall Windows completely?
I've been talking to a few people and it's happening to them to on Windows 10 I think it's just a bug from a recent update try a roll back
lorfo123 said:
I've been talking to a few people and it's happening to them to on Windows 10 I think it's just a bug from a recent update try a roll back
Click to expand...
Click to collapse
How should one file a bug-report for windows 10 then, this can't be something that shouldn't keep unnoticed by them.
Did rolling back fix something for you, and how did you do so?
I've checked another Windows 10 computer which hasn't been updated and it recognises my one plus 3T so if you Google / YouTube windows 10 roll back it should work
Hmm this does suck. This means I cant be up to date on windows for now. Anybody have different suggestions?
1asbak1 said:
Hmm this does suck. This means I cant be up to date on windows for now. Anybody have different suggestions?
Click to expand...
Click to collapse
The only other thing I could suggest is using a virtual machine to run win 7
Did you try back usb ports?. My pc with windows 10 fails with the front ports.
Solution
Backup all the data in your internal memory and try the 'format data' option from twrp to wipe your internal storage. It could solve your problem, as it did in my case.
New solution, just done works!
Plug in your phone and on the computer go to device manager (have phone in MTP mode)
you'll find the phone as a unknowen device
right click on this select "update driver software..."
a window will pop up select "browse my computer for driver softaware"
then on the next bit select "let me pick from a list of device drivers on my comupter"
then you will have a box with "MTP Device" and "MTP USB device"
select "MTP USB device" hit next and it should work 100%
ayush2901 said:
Backup all the data in your internal memory and try the 'format data' option from twrp to wipe your internal storage. It could solve your problem, as it did in my case.
Click to expand...
Click to collapse
Which version of TWRP are you running? The thing is that If I afterward can't restore the data via USB haha, then the whole point of backing it up seems invalid
lorfo123 said:
New solution, just done works!
Plug in your phone and on the computer go to device manager (have phone in MTP mode)
you'll find the phone as a unknowen device
right click on this select "update driver software..."
a window will pop up select "browse my computer for driver softaware"
then on the next bit select "let me pick from a list of device drivers on my comupter"
then you will have a box with "MTP Device" and "MTP USB device"
select "MTP USB device" hit next and it should work 100%
Click to expand...
Click to collapse
This actually worked. Wauw.
Had to reboot a view times in order to get it in effect, nonetheless, THANKS let the creativity start again
Really,My A** is burnt while my phone showing messages to update,,, Fiunally donw..Thanks a lot...!!
super it works
This solution did not work for me. I am using W7 and OOS 5.0.3 rooted. Tried updating MTP drivers in W7, the phone shows up but no data shows in the drive. Still looking for a solution. Can someone please post W7 drivers that work for them? Thank you.
picollo7 said:
This solution did not work for me. I am using W7 and OOS 5.0.3 rooted. Tried updating MTP drivers in W7, the phone shows up but no data shows in the drive. Still looking for a solution. Can someone please post W7 drivers that work for them? Thank you.
Click to expand...
Click to collapse
When you connect the phone to pc do you get a notification on your phone with the USB options?
DirkGently said:
When you connect the phone to pc do you get a notification on your phone with the USB options?
Click to expand...
Click to collapse
yes I can select charge, mtp, ptp, or midi
in device manager sometimes the phone shows up with error 10, device cannot start
tried many different driver versions in updating driver
picollo7 said:
yes I can select charge, mtp, ptp, or midi
in device manager sometimes the phone shows up with error 10, device cannot start
tried many different driver versions in updating driver
Click to expand...
Click to collapse
I doubt there's much we can suggest that you haven't already tried. Try another cable/USB Port/uninstall device from Device Manager and let Windows find the driver. Hell, you probably did all that already.
DirkGently said:
I doubt there's much we can suggest that you haven't already tried. Try another cable/USB Port/uninstall device from Device Manager and let Windows find the driver. Hell, you probably did all that already.
Click to expand...
Click to collapse
Haha, yeah. Does anyone have links to the drivers that work for them?