Related
Hi @ all !
There´s a thing very annoying in the new Kaiser... You cannot use any belt-pocket with magnetic closers !
After setting the phone to standby via one short press on power button, I found it back turned on again, everytime I took it out of the belt-pocket.
First I thought, that this must be the keyboard slide mechanism, cause the phone also comes back, when you slide out the keyboard, but I kept an eye on it, not the move the slider while putting it into the pocket and back out again. Then I thought, that it was the light sensor, but some tests made me sure, that it must be something else.
Finally I found out, that it turns back on again, cause I´m still using the belt-pocket of my old TyTN I with the 2 magnets as closing mechanism... If you try and hold a magnet over the keyboard in the area of S,D,E,X,F or even on the back side in the same area and move it around just a little bit, the phone turns on... Crazy, but true !
Now I know, why they gave that awful new belt-pocket with the tape-closer to the Kaiser...
Hope that helps
Marco
It is partly related to keyboard... it has a magnetic sensor that it is activated when keyboard is released, so the magnet from your holster tricks the sensor into believing keyboard is out, so it activates screen.
I guess thats why they have the velcro closer on the one that is shipped with the phone. This is somthing to consider when buying a nice Piel Frama one.
Absolutely it's the keyboard magnet operated switch that does it. But, I know you can run a magnet (let's say the case magnet ) over the d-pad area (seems to do it on mine) and the Kaiser will turn on. - However, I have been using the TyTn case also and I have not noticed it turning on just by sliding the Kaiser in and out. In fact I have just sat here and put it in and out every which way (for the last ten minutes) and it has not come on.
Maybe your magnets are stronger than mine or your keyboard switch more sensitive? I am also not keen on that "tape" closing on the new case.
Mike
lol i wish i would have read that some place, i thought it was the keyboard some switch but didnt think they would use a magnet, it was pissing me off a lot while i was driving, now i know i found on my own, but the magnet that i have is shielded a bit, but still just the right position and it will trigger the switch
I sure hope this was posted some place in a FAQ or wiki, if not it should be and if it was, then shame on me for not reading that part or noticing it
Magnetic sensor via magnet in holster.
Just found out this "feature" with a BB holster...
Has anyone found a way to exploit/use this feature to turn-on the device when removed from the holster?
That is something I always envied with my wifes Blackberry.
I've noticed this too
I have the same problem, but since mine is set not to wakeup when the keyboard slides open I can't see how the magnet could be the culprit.
I had the same problem with my Nokia and Kaiser.....Never thought it was because of the magnet sensor in the device....To tell the truth...I didnt know that it had one inside.....Thanks for the info....
Would it affect the sensor in anyways....if it doesnt, I can actually use this "feature" so my phone is awake each time I pull it out of the belt case......
hi guys
I have Att tilt and since 3 days a go my phone keep turning on by it self. any ideas how to fix this? Thanks.
i'm defnitely sure u need to call in an exorcist. for the time being, pls place the phone within a ring of garlic cloves
It's probably the instant messenger receiving an SMS message with someone signing on/off or you getting a message.
if you are using a case with a magnet in it it will cause it to turn on like if you were sliding it open to fix this download kaiser tweaks and turn off the option to turn on when slide open or keep away from magnet cases
Re
steve960 said:
if you are using a case with a magnet in it it will cause it to turn on like if you were sliding it open to fix this download kaiser tweaks and turn off the option to turn on when slide open or keep away from magnet cases
Click to expand...
Click to collapse
This is indeed the only thing i can imagine is happening. Strong radiowaves can turn on/off devices and even uses them..... Just to give a exemple, I work on a warship and we had a 250KW powercable with some leaks in the isolation. This causes some of the other equipment to power on and even use it while all safeties were still on!
thanks guys for your help. i will try to disable the sliding thing. i hope it works.
Verified
My brother wanted to give me his old Wizard holster which closes with a magnet. I told him the magnet might cause my screen to turn on. Sure enough, as soon as the phone got near the holster the screen came on and switched to landscape just as it would if I had flipped out the keyboard.
Guess that's why my Kaiser came with a holster that uses velcro.
This has been driving me nuts since I got my Tilt! The slightest sliding movement of my screen would wake the phone up.
Thanks for the easy fix with the Kaiser Tweak setting!
Hi guys,
I did the Kaiser Tweak setting but still same issue from before. every like 5 to 10 min my phone comes on by itself.
any other sugestions?
now im having the same problem. wtf is going on. no magnets near my phone. it sucks lol
Home button just stopped working. Its happened a couple of times before, but it comes back after a day or so. Is this a common problem on the ds7? I didn't find any mention of this anywhere.
If honeycomb have the button bar at the bottom when its released, this wont be a problem.
vtinmanv said:
Home button just stopped working. Its happened a couple of times before, but it comes back after a day or so. Is this a common problem on the ds7? I didn't find any mention of this anywhere.
If honeycomb have the button bar at the bottom when its released, this wont be a problem.
Click to expand...
Click to collapse
I have never seen this problem, and have not heard about it before. Have you try to search for an app that remap button?
The home button is working again after I left it alone overnight and restarted it in the morning.
After thinking about it a bit, it seems that every time the home button stops working, it's after I take the Streak out in my jacket pocket. I think this may be a problem with static electricity, the screen have been rubbing against my jacket so it's always spotless when I take it out of my pocket. But why is only the home button affected?
Can anyone recommend a good anti-static case for the Streak 7?
EDIT: Spoke too soon, it seems on and off. But it's definitely static that caused this.
vtinmanv said:
The home button is working again after I left it alone overnight and restarted it in the morning.
After thinking about it a bit, it seems that every time the home button stops working, it's after I take the Streak out in my jacket pocket. I think this may be a problem with static electricity, the screen have been rubbing against my jacket so it's always spotless when I take it out of my pocket. But why is only the home button affected?
Can anyone recommend a good anti-static case for the Streak 7?
EDIT: Spoke too soon, it seems on and off. But it's definitely static that caused this.
Click to expand...
Click to collapse
I'm using this case, it fit perfect because its made for the ds7. I don't know if its anti - static or not, but it close into a book like style. I'm not affiliated with this eBay seller, just using it for reference.
http://www.ebay.com/itm/NEW-T-MOBIL...580194?pt=PDA_Accessories&hash=item23128548e2
otnos said:
I'm using this case, it fit perfect because its made for the ds7. I don't know if its anti - static or not, but it close into a book like style. I'm not affiliated with this eBay seller, just using it for reference.
Click to expand...
Click to collapse
I was eyeing this case too. But since the button is already broke, no point in getting a case now. Hopefully, this will be a non-issue once I install honeycomb since it'll have the action bar. Assuming it works just like 3.1 on a galaxy tab 10.1. In fact, I might be looking for a way to disable the hardware buttons.
vtinmanv said:
The home button is working again after I left it alone overnight and restarted it in the morning.
After thinking about it a bit, it seems that every time the home button stops working, it's after I take the Streak out in my jacket pocket. I think this may be a problem with static electricity, the screen have been rubbing against my jacket so it's always spotless when I take it out of my pocket. But why is only the home button affected?
Can anyone recommend a good anti-static case for the Streak 7?
EDIT: Spoke too soon, it seems on and off. But it's definitely static that caused this.
Click to expand...
Click to collapse
I've had my screen itself be poor or nutty responsive behaviour, but I can almost always turn the screen off and back on and it fixes it. Usually happens when I pull it out of my pocket and it's either still partly in my pocket or my fingers are on the screen while turning it on. Seems all capacitive devices do a screen calibration on screen-on and it hoses it when it's being touched.
This afternoon when I pulled my spen out I noticed some serious issues. For some reason in any ROM I use stock or otherwise, the spen acts very weird. I have no idea how this happened as I haven't damaged the pen in any way.
Just having it hovering above the screen for some reason it thinks that I'm touching the display. I can open apps, long press, and swipe all by having the pen hover over the display. The cursor does not show up at all, but pressing the button opens air command and it then brings up the cursor, but only until you select something from the air command wheel.
Any solution to this? Its driving me nuts as I use the spen quite often.
ohmygaa said:
This afternoon when I pulled my spen out I noticed some serious issues. For some reason in any ROM I use stock or otherwise, the spen acts very weird. I have no idea how this happened as I haven't damaged the pen in any way.
Just having it hovering above the screen for some reason it thinks that I'm touching the display. I can open apps, long press, and swipe all by having the pen hover over the display. The cursor does not show up at all, but pressing the button opens air command and it then brings up the cursor, but only until you select something from the air command wheel.
Any solution to this? Its driving me nuts as I use the spen quite often.
Click to expand...
Click to collapse
Pretty much the same thing happened to me. It drove me crazy trying to find a fix and finally I just bought a replacement pen and that did the trick. I got my replacement for cheap on Amazon.
Aw man, I wasn't looking to spend any money but oh well. Thanks a lot for your help.
ohmygaa said:
Aw man, I wasn't looking to spend any money but oh well. Thanks a lot for your help.
Click to expand...
Click to collapse
Use tool suplied with phone remove, clean and reinsert the tip. It may solve your problem. It sound like tip is stuck inside pen.
Sent from my SM-N910T using XDA Free mobile app
darekz said:
Use tool suplied with phone remove, clean and reinsert the tip. It may solve your problem. It sound like tip is stuck inside pen.
Sent from my SM-N910T using XDA Free mobile app
Click to expand...
Click to collapse
This fixed it perfectly. Just used a dust can to blow whatever was inside my spen, and it works flawlessly.
Is there any way to disable the magnetic sensor on the N6? I have a smart cover that keeps constantly turning the screen on in my pocket and it's killing my battery. It is a very nice luxury case and I don't want to damage it or replace with another cover. I tried finding an app that would do it but no luck. Any help would be greatly appreciated!
bobprobert said:
Is there any way to disable the magnetic sensor on the N6? I have a smart cover that keeps constantly turning the screen on in my pocket and it's killing my battery. It is a very nice luxury case and I don't want to damage it or replace with another cover. I tried finding an app that would do it but no luck. Any help would be greatly appreciated!
Click to expand...
Click to collapse
Dont think there is a way to disable it yet.
Although i read elsewhere its located in /sys/module/ and adding a '0' or 'false' to the value will disable. Issue is still not located the magnetic sensor, older devices it was in /sys/module/lid/parameters/lid_enabled.
But no luck on N6 yet
has anyone had any luck using an app to accomplish this?
bobprobert said:
has anyone had any luck using an app to accomplish this?
Click to expand...
Click to collapse
Found nothing to disable the magnet sensor.
Installed Xposed and a MagnetOff app. But it did not disable the magnet sensor.
Because I cannot disable that feature, I decided to use it.
On the outside of my belt case I attached a small magnet (glue) and now my screen is always off when the N6 is in the case.
When I take the N6 out of the case the screen turns on. No need for pressing a button.
NLBeev said:
Found nothing to disable the magnet sensor.
Installed Xposed and a MagnetOff app. But it did not disable the magnet sensor.
Because I cannot disable that feature, I decided to use it.
On the outside of my belt case I attached a small magnet (glue) and now my screen is always off when the N6 is in the case.
When I take the N6 out of the case the screen turns on. No need for pressing a button.
Click to expand...
Click to collapse
you sure the screen is always off when it's in your case? like the OP, I found that my screen would periodically come on when using a flip case that has the auto on feature (while closed).
PhilDX said:
you sure the screen is always off when it's in your case? like the OP, I found that my screen would periodically come on when using a flip case that has the auto on feature (while closed).
Click to expand...
Click to collapse
When de magnet is close to the circle with the Motorola logo the screen is switched off.
I am using a flat neodymium magnet with a diamater of 10 mm.
Because the case is partly open at the top, I can see that the screen is really off when the N6 is in the belt case.
http://www.ebay.com/itm/Cool-CowBoy...t=LH_DefaultDomain_0&var=&hash=item4d2493c910
When you are unsure if the screens will be turned off when the N6 is in the case, use a stronger magnet.
I mounted with glue a magnet at the outside and put a second one on the inside.
So I am using two small magnets.
any developer willing to dig into this issue to try to find a solution?