[Q] Pressure test dowsn't work? - Xperia Z3 Compact Q&A, Help & Troubleshooting

Hey guys, i saw a thread with presure test that's possible on my Sony z3 compact. But unfortunately, i tried it and the value doesn't change and stays at 965,30.
I've tried to put it under water but no water damage is seen. What could be wrong?
Thank you.

You have to press on the screen with a finger...

Foxhunter123 said:
You have to press on the screen with a finger...
Click to expand...
Click to collapse
I am doing that...

well if it doesn't move, then usually that means it's compromised somehow. maybe your flags aren't closed correctly.

They are... Is the pressure test a proof for the store? Do you have any experiences with that?
Thanks

not really. but i think they perform it during warranty/service to check.

My Z3 does show a higher value but drops slowly after that. so i guessed there was a leak. I held it under water and no leak. But when i pressed on the device there were coming bubble out of the wristband holder on the bottom left of the device. Not the screens but really the hole itself.
Im not sure if its a leak or its some sort of pressure regulator that makes sure that not to many pressure gets on the Phone when the air inside is heated up.

it's the latter.
If the case was 100% air-tight the barometer would not work. There is probably a membrane/valve to adjust to pressure changes. This is the same on all Z3 and Z3c devices. That is also why the pressure drops.

donscarface said:
Hey guys, i saw a thread with presure test that's possible on my Sony z3 compact. But unfortunately, i tried it and the value doesn't change and stays at 965,30.
I've tried to put it under water but no water damage is seen. What could be wrong?
Thank you.
Click to expand...
Click to collapse
Make sure the USB/SD and SIM covers are firmly closed. The pressure test on my phone didn't work until I pressed those two firmly closed and then it worked -- pressure increases 1-2mb briefly then drops back to (or below) original value. That's why I plan to use a magnetic charger... those covers are clearly a weak point and could prove to be the death of the phone if it's dunked

pipspeak said:
Make sure the USB/SD and SIM covers are firmly closed. The pressure test on my phone didn't work until I pressed those two firmly closed and then it worked -- pressure increases 1-2mb briefly then drops back to (or below) original value. That's why I plan to use a magnetic charger... those covers are clearly a weak point and could prove to be the death of the phone if it's dunked
Click to expand...
Click to collapse
Trying it but it has no effect... I am using the magnetic charger too... Did you try to return to the store?
Thanks for reply...

Related

My Xperia Z failed the water test out of the box!

Hello all, just wanted to inform all that I've experienced this odd thing with the Z that no one has seemed to have gone through, not sure of course...
But before anything else, as it was a huge selling point for a lot of hiking and travelling me, the water proofing needed to be tested.
I took it out of the box, peeled the plastic protectors off the front and back glasses, threw it in a glass.
- Now my camera has some fog inside, the volume down button has started to work again after half an hour, the loudspeaker is understandably very bad right now.
- Currently trying to get the fog out of the camera and hoping the loudspeaker to go back to normal.
- I will contact Sony tomorrow to discuss the problem and will update this as often as I can.
/**************************************************************/
Solved!
- As Akiainavas has pointed out to me, it is actually written in the instructions manual, it is normal for the camera to get foggy between shifts from under water to outside the water, I've tested it work perfectly under water.
- Once dried out, all is good, it just took a lot longer for me compared to other people because of the low room temp I am used to I guess.
- The phone is all good, all working.
* Now on the to-do list: Unlock, Root, Flash, Enable Bravia through the whole user experience!
I heard that this is actually not uncommon. Let it dry. Try again tomorrow.
Indeed, i tested it the day i got and noticed the sound was very low after it was wet. After a half an hour (max 1 hr) sound will come back with normal volume. It's some protection thing i guess
It's just water on the speaker membrane that distorts the sound. Haven't got my phone yet, but try blowing it out. Waiting it out should work as mentioned.
AlienCraB said:
Now my camera has some fog inside
Click to expand...
Click to collapse
Still have that problem?
Maybe its a faulty device with regard to that camera fog.... Can happen to one in thousand devices...
Surely sony will replace it...
Sent from my HTC_Flyer_P512_NA using xda app-developers app
nikhiltanwar said:
Maybe its a faulty device with regard to that camera fog.... Can happen to one in thousand devices...
Surely sony will replace it...
Sent from my HTC_Flyer_P512_NA using xda app-developers app
Click to expand...
Click to collapse
This brings up a Good question. Has anybody read the warranty?Does it actually Say You are Covered it you purposefully dunk it in a bowl of water?
I mean I understand there have been demonstrations doing this but it Seems like a really silly thing to do with your brand new phone
stiffi2011 said:
This brings up a Good question. Has anybody read the warranty?Does it actually Say You are Covered it you purposefully dunk it in a bowl of water?
I mean I understand there have been demonstrations doing this but it Seems like a really silly thing to do with your brand new phone
Click to expand...
Click to collapse
the matter is...
xony xperia Z has the CERTIFICATION, wich isn't something you say you have, is something that has to been tested by a specific organization...
so if is certified i think you have warranty right...
never had any issues with fog in the camera on my xperia acro s, even after having it in my pocket while swimming
the speakers issue is common though, but thats expected, as water is going to get inside the speaker holes no matter what, but all I need to do is just shake the phone and blow where the speakers are and they work perfectly fine after that
Uh...did you even at least try to test out to make sure the phone is working good before dumping it into the water?
Right, it's been 12 hours now, I left it to dry out in a bag full of humid absorbing silicon bags over night.
- Right now the fog inside the camera lens is gone.
- However I think it is out of battery so I plugged into charging.
CaFFeiNe666 said:
the matter is...
xony xperia Z has the CERTIFICATION, wich isn't something you say you have, is something that has to been tested by a specific organization...
so if is certified i think you have warranty right...
Click to expand...
Click to collapse
Exactly what I have in mind, I will be contacting Sony about this no matter what, the phone failed the water test out of the box, it is a feature they promote and demonstrate heavily. If they don't cover it in their warranty despite all the promotion and the effort they have put in this phone, then they are just idiots who have absolutely no idea of how one device failing like this can damage the image if they don't back it up with their warranty.
rycexboi said:
Uh...did you even at least try to test out to make sure the phone is working good before dumping it into the water?
Click to expand...
Click to collapse
Yes, it was all fully working - tested its other features without opening any of the covers to make sure the water test was legit for an hour or so.
/***************************************************/
Update: The phone is working, buttons all working, speaker working, camera fog gone and this time it didn't come back as soon as I took it out of the air lock bag.
I am still contacting Sony to get information on what I should do, how I should feel...
I will test it again after my talk with them and on the direction they've given. Mind you, I tested it only in a half full glass of water so what I will do is to try and reproduce the problem.
/***************************************************/
Update 2: I have just noticed that the charger is actually 1.5A and you cannot charge the phone from a computer unless you have a non-standard USB port like a 3A one that Gigabyte motherboards have.
Put mine in a vase of water yesterday for 5 mins and all was well, love it
Sent from my C6603 using xda premium
When submerged, and after that:
- Speaker will have very low volume for a while, until it dries off
- There might be a "fog" on the camera because of humidity and temperature differences
- Hardware buttons might not react perfectly until the water dries off
It's perfectly normal. It's in instruction manual... but whoever reads those these days
Quick copy and paste from the Sony UK website.
"[2] In compliance with IP5/7 and IP5X, Xperia Z is protected against the ingress of dust and is water resistant. Provided that all ports and covers are firmly closed, the phone is (i) protected against low pressure jets of water from all practicable directions in compliance with IP 55; and/or (ii) can be kept under 1 metre of freshwater for up to 30 minutes in compliance with IP 57. The phone is not designed to float or work submerged underwater outside the IP55 or IP57 classification range and should not be exposed to any liquid chemicals. If liquid detection is triggered on the handset or battery, your warranty will be void."
So it's only designed to be water resistant, and if it gets water damage, you're out of luck.
mustaine8661 said:
So it's only designed to be water resistant, and if it gets water damage, you're out of luck.
Click to expand...
Click to collapse
The thing is - it won't get damaged unless you leave the covers open. I asked Sony about it and apparently they have some tests to determine that - most likely a water detection that can be used even when the phone is dead. I think they'll probably just close the covers and put it in water to test it again, if waters gets in - it means your covers are flawed and you'll get a replacement. If not - it means you fkd up and you won't get your phone replaced.
Akiainavas said:
The thing is - it won't get damaged unless you leave the covers open. I asked Sony about it and apparently they have some tests to determine that - most likely a water detection that can be used even when the phone is dead. I think they'll probably just close the covers and put it in water to test it again, if waters gets in - it means your covers are flawed and you'll get a replacement. If not - it means you fkd up and you won't get your phone replaced.
Click to expand...
Click to collapse
If that's the case then then that's awesome!
It'd make sense too, as what's the point of going to all the trouble of getting it certified water-resistant and advertising it as one of the main features, and then saying to everyone that gets the slightest bit of water ingress that they're f**ked.
mustaine8661 said:
If that's the case then then that's awesome!
It'd make sense too, as what's the point of going to all the trouble of getting it certified water-resistant and advertising it as one of the main features, and then saying to everyone that gets the slightest bit of water ingress that they're f**ked.
Click to expand...
Click to collapse
I trust Sony in this aspect. There are water sensitive tapes under every cover ( those little white things ) so they'll know which one leaked.
Also, remember what happened with Tablet S - it was supposed to be waterproof, but they detected a manufacturing defect that caused some of them to leak. Sony called every customer to Sony Center and provided a replacement of their device - dead or not, warranty or not... that's how you do it.
mustaine8661 said:
Quick copy and paste from the Sony UK website.
"[2] In compliance with IP5/7 and IP5X, Xperia Z is protected against the ingress of dust and is water resistant. Provided that all ports and covers are firmly closed, the phone is (i) protected against low pressure jets of water from all practicable directions in compliance with IP 55; and/or (ii) can be kept under 1 metre of freshwater for up to 30 minutes in compliance with IP 57. The phone is not designed to float or work submerged underwater outside the IP55 or IP57 classification range and should not be exposed to any liquid chemicals. If liquid detection is triggered on the handset or battery, your warranty will be void."
So it's only designed to be water resistant, and if it gets water damage, you're out of luck.
Click to expand...
Click to collapse
Akiainavas said:
The thing is - it won't get damaged unless you leave the covers open. I asked Sony about it and apparently they have some tests to determine that - most likely a water detection that can be used even when the phone is dead. I think they'll probably just close the covers and put it in water to test it again, if waters gets in - it means your covers are flawed and you'll get a replacement. If not - it means you fkd up and you won't get your phone replaced.
Click to expand...
Click to collapse
I've read it somewhere that the interior also has water resilient coating actually for when tiny amounts of water goes in, I wonder if that's why the camera gets fogged inside because I just don't get how there can be fog when there is no humidity allowed into the interior components as long as you are in the limits of the IP57 certification.
Am I wrong in this? Does water proofing not mean the device not allowing any humidity inside whatsoever? or Is it that the air molecules carrying the humidity inside can still get past the water proofing?
Akiainavas said:
The thing is - it won't get damaged unless you leave the covers open. I asked Sony about it and apparently they have some tests to determine that - most likely a water detection that can be used even when the phone is dead. I think they'll probably just close the covers and put it in water to test it again, if waters gets in - it means your covers are flawed and you'll get a replacement. If not - it means you fkd up and you won't get your phone replaced.
Click to expand...
Click to collapse
under flap covers there's a water-sensitive material wich becomes pink when water enters slots i've seen a photo from a review, but he has put his xperia z in many kind of water, beer too (beer has bubbles and carbon dioxide )
CaFFeiNe666 said:
under flap covers there's a water-sensitive material wich becomes pink when water enters slots i've seen a photo from a review, but he has put his xperia z in many kind of water, beer too (beer has bubbles and carbon dioxide )
Click to expand...
Click to collapse
I'm much more likely to spill beer over it rather than water in perfect honesty, so thanks for the info there!
Not that I want to spill any beer... it's so sad when I do :crying:

[Q] Does my Xperia Z lost water resistance?

Hello,
I have my Z from its release. I tried its water resistance the first day i recieved it, all was OK. I recorded many videos underwater, in swimming pool, at home, and everything was always ok. Everytime i took it in water, I mindfully closed all the covering caps.
But today, I got a problem. I took my phone with me to water, as whnever I did, and when I was looking at it after "bathing", my camera was fogged - it was wet INSIDE. I tried to check those white indicators under covering caps, and those at USB port and headphone jack were RED. I also noticed tiny droplets of water there. Everything else is however working. No display issues, headphones are playing, USB works too.
I must remark that my phone dropped me on pavement from my pocket about month ago (scratched corners), but its resistance worked until today.
What now? Should I claim it? What do you guys think? I bought Xperia Z mainly for its water resistance. It is very distressing that I can take it in water any more.
Edit: one problem detected - mobile data doesnt work.
Since the indicators are red you have nothing to stand on, they will just say that the flaps were open and you won't be able to prove them wrong.
Dsteppa said:
Since the indicators are red you have nothing to stand on, they will just say that the flaps were open and you won't be able to prove them wrong.
Click to expand...
Click to collapse
I read somewhere that on the repair service they check if the flaps provide the necessary seal against water. If they provide enough seal, and you have the indicators turned red, they blame you for not having closed the flaps correctly, on the other hand, if the flaps show defects and let water through, even when properly closed and with moisture indicators turned red, they still service your device under warranty.
Dsteppa said:
Since the indicators are red you have nothing to stand on, they will just say that the flaps were open and you won't be able to prove them wrong.
Click to expand...
Click to collapse
They were closed. I was always checking them before going in water. Im 100% sure. And yes i can prove it. They can close the flaps and test phone and see if there is water or not.
Dropping the phone may have caused an open gap somewhere and water leaked in.
Nothing you can do, just argue your way in and hope for the best.
If you know you are a clumsy person, you should have gotten a case.
Sent from my C6603 using xda premium
In the pictures the phone has a the back glass lifted, maybe that was the problem. I have the back lifted too , but not that high as yours.
Don't tell them you used it in the swimmingpool, it clearly says in the instruction booklet that you should't.
Swimmingpool water contains acids and chemical products that may destroy the rubber seals over time.
I think I know what happened. Flaps may be ok (I tested to put the phone in water again - there were no water under them, but water still got to a phone - my volume down is damaged now), but the right issue is that back plate is raised a bit around the camera
Type "Sony Xperia Z repair, disassembly manual" on youtube.
As you can see on this video, right under the plate are phone GUTS. The plate can be raised by warming it. Thus it can raise when you play games or a sun is shining on a phone. All Xperia Z owners, check your back plate too if it is OK or raised! I believe this is that water resistance issue..
The fog in camera disappeared during the day and when I removed SIM and put it back, mobile data begun to work. Bad thing is that volume button doesnt work (as I said above). The button itself is ok and its not stucked or pressed, but when I turn phone on, it always starts in safe mode and I cant volume down, I can just volume up (using the button; I can volume down using display), so I think button contacts are fu**ed and phone thinks the buton is pressed. I think only thing I can do now is going to repair service.
I could never imagine submersing my phone in water. not worth the risk.
I treat my XZ as water resistant. I'll text people when im in the bath with wet hands etc.. but never put it in water
eiestsa never
vibecatalin said:
In the pictures the phone has a the back glass lifted, maybe that was the problem. I have the back lifted too , but not that high as yours.
Click to expand...
Click to collapse
Yeah, you are right. I think thats the issue. Did u try to put it in water if it is ok or not?
I've read somewhere of someone using bleach on a cotton bud VERY carefully to whiten the markers.
I had a similar issue, take it to the service center & get it fixed.
VykoJust said:
Yeah, you are right. I think thats the issue. Did u try to put it in water if it is ok or not?
Click to expand...
Click to collapse
No, but I think I will try.
vibecatalin said:
No, but I think I will try.
Click to expand...
Click to collapse
Those flaps are piece of crap. Especially that flap where charger/data cable go. Since we playing with it every day, my guess is that sealing got weaken and that's why water got thru the phone. Gap may be less than tenth of a millimeter ( <0,1 mm) and water can easily come in.
i think it's time again to bash those people who warn others not take their phone into water, as the xperia z is not waterproof, but just water resistant. and that's more likely to protect the phone from accidental drops into water, rather than to go diving/bathing/filming with it in water.
and those warners know what the IP-rating says ("...half an hour"..."submerged 'till half a meter"....)
hebbe said:
i think it's time again to bash those people who warn others not take their phone into water, as the xperia z is not waterproof, but just water resistant. and that's more likely to protect the phone from accidental drops into water, rather than to go diving/bathing/filming with it in water.
and those warners know what the IP-rating says ("...half an hour"..."submerged 'till half a meter"....)
Click to expand...
Click to collapse
If people actually followed that advice, then there would not be multiple threads like this one, where people have destroyed their phone.
What is the point of deliberately putting your expensive phone in danger, IP rating or no IP rating?
Sent from my C6603 using Tapatalk 2
kingvortex said:
If people actually followed that advice, then there would not be multiple threads like this one, where people have destroyed their phone.
What is the point of deliberately putting your expensive phone in danger, IP rating or no IP rating?
Sent from my C6603 using Tapatalk 2
Click to expand...
Click to collapse
gosh, not this discussion again! It does not matter what the point is or if there is a point or not. If the producer communicates that this phone CAN sustain without damage being in water i-don't know-how-deep for i-don't know-how long, then this phone SHOULD do it. The intentions of the users, or whether there is a point or not in taking your phone to the swimming pool, are NOT important. It is IMPORTANT that whatever was promised to the user SHOULD BE VALID.
tudork said:
gosh, not this discussion again! It does not matter what the point is or if there is a point or not. If the producer communicates that this phone CAN sustain without damage being in water i-don't know-how-deep for i-don't know-how long, then this phone SHOULD do it. The intentions of the users, or whether there is a point or not in taking your phone to the swimming pool, are NOT important. It is IMPORTANT that whatever was promised to the user SHOULD BE VALID.
Click to expand...
Click to collapse
Perhaps you have a point, but if you go to a service centre with red water ingress indicators, you will be paying to have your phone repaired as they will say it was caused by user negligence. End of story.
If you do not put your phone into water for no good reason, it will never get water damaged. Why are people using the IP rating to excuse a complete lack of common sense?
Why do people NEED to put their phone into water regularly?
Sent from my C6603 using Tapatalk 2
kingvortex said:
Perhaps you have a point, but if you go to a service centre with red water ingress indicators, you will be paying to have your phone repaired as they will say it was caused by user negligence. End of story.
If you do not put your phone into water for no good reason, it will never get water damaged. Why are people using the IP rating to excuse a complete lack of common sense?
Why do people NEED to put their phone into water regularly?
Sent from my C6603 using Tapatalk 2
Click to expand...
Click to collapse
because they bought the phone with the intention that they can do this with it. They've seen it in official Sony commercials (phone used during rain, phone washed under running water after being splashed with color paint, on exhibitions Sony employees dropped it in aquariums, smashed the phone on the floor repeatedly to demonstrate that the glass won't break). I heard that in some shops they even have the Z in a water tank all the time and only take it out for charging. There was that show in Czech Republic where two models used the phone under the shower and so on.
The phone has an ip57 rating which clearly states that you can submerge it into water for 1m and up to 30 minutes. I also believe that you can leave it there for much longer and it SHOULD be okay, only the depth is important. The deeper you go, the higher is the water pressure and the seals might leak.
Now, cars also have ip ratings for water protection and different levels for the interior of the car and the outside. Inside it might be ip54 (water, mud and splashes when entering the car with wet shoes or boots) and outside it's even ip59 or ip58K which means it's protected against water ingress when used with high pressure water jets (e.g. car wash!).
I'm sure most people would complain, if there brand new car is flooded with water on the inside after they went to car wash. The same is true for this phone!
An ip rating is an ip rating and not like "buhu, it's ip57 but it can only manage 3 drops of water before it breaks!". If that is the case, I could have keept my S2 which also survives a few drops of rain without damage. If Sony can't manage that, they shouldn't have advertised it like that or given an ip54 rating or something lower.
You can't claim your phone has the SECOND HIGHEST protection against water there is and then say: "Stay away from water". It's like: "your car has 6 airbags, but don't expect them to work in a crash" or "your Porsche can go 300 km/h, but don't ever try it"
People put their phone in water because they can and should be able to.
If the XZ can't and should be used in water, I'm sure most people would have bought a non water proof phone instead because it would be the same. I was drawn to this phone because of it's water resistance.
I'm beeing very paranoid and bought a 5€ waterproof bag for my phone which I tested yesterday for 6 hours submerged in the sink. The paper inside stayed perfectly dry. Even though my XZ should be waterproof on its own, I think double protection is always better. The bag seems to be waterproof, and even if by some chance it is not, then my phone won't be damaged, because it's supposed to be waterproof too!
With this double protection, I'm still afraid to take it to the pool, but might do so eventually which I wouldn't have done without the bag.
Yes, you do have a point. At least somewhat anyway.
For a start, the manual tells you to avoid chlorinated water. So no swimming pools. I wonder if this is why the water resistance appears to have failed in this case.
I could point out other things that the manual tells you to avoid, but everyone here has already read it before going swimming with their phone, right?
Sent from my C6603 using Tapatalk 2

Galaxy S4 Active - is it really waterproof?

USA Today have an article (here) where the reviewer was testing the S4 Active. Right after he dunk the phone underwater, the phone have WATER DAMAGE:
Shortly after I took the phone for a dip (in not very deep water), the display went kaput — at least for several hours. It lit up just long enough to indicate that I had power, but I couldn't actually keep the display on and use it.
Roughly a day later, the screen came alive again, but the phone was still exhibiting finicky behavior, presumably because of water damage. The touch-screen was messed up and the device acted as if headphones were plugged in when they weren't. If this were my actual phone, I'd return to the store for a replacement.
I just got the S4 Active and thought I am not planning to take the phone for a long underwater activities, I am concerned that I am getting a phone that have a very weak water resistant feature.
Not sure if this is because the reviewer didn't "properly" close the battery cover / USB port, but I have seen S4 Active review and Samsung Event videos where the phone was submerged in water for a long time and it still works.
PS: Have ANYONE tried to dunk their phone in the water for testing?
My phone has been in a pool, lake, bathtub, rainy weather, all since I got it. I trust it.
Sent from my SAMSUNG-SGH-I537 using Tapatalk 2
I'd like to think that reviewer just got stuck with a bad unit.
But this begs the question: Is water damage covered under warranty? Either by AT&T or Samsung? Surely they should back up their "vacation-proof" phone..
aceownstheworld said:
My phone has been in a pool, lake, bathtub, rainy weather, all since I got it. I trust it.
Sent from my SAMSUNG-SGH-I537 using Tapatalk 2
Click to expand...
Click to collapse
My first one went into the pool just fine. The unit I have now I am scared to expose it. On the top between the glass and bezel there is a small gap... above the in call speaker.... I'm afraid that water will pour in through that... Can you look at yours and see if yours is like that?
He probably didn't press down the back cover correctly.
Sent From My Galaxy S4 Active using a Tapatalk 4
joshuadjohnson22 said:
My first one went into the pool just fine. The unit I have now I am scared to expose it. On the top between the glass and bezel there is a small gap... above the in call speaker.... I'm afraid that water will pour in through that... Can you look at yours and see if yours is like that?
Click to expand...
Click to collapse
You mean between the earpiece and the bezel at the front? I don't see any gaps, at least not with my naked eyes.
On the back, bottom part near the speaker, I don't see it either. Trying to press to see if there is a gap, so far none.
What makes you "scared" on the phone that you have now?
robstunner said:
He probably didn't press down the back cover correctly.
Sent From My Galaxy S4 Active using a Tapatalk 4
Click to expand...
Click to collapse
There is a sticker on the back cover that provide a warning for the user to PRESS DOWN on the middle of the cover, underneath the LED.
I always do that, but I never hear a "click" or any indication that the back cover is now PROPERLY covering the phone to prevent water leakage.
Well, I DO hear the click when pressing on all sides, but that's normal like my Galaxy Note.
lanwarrior said:
You mean between the earpiece and the bezel at the front? I don't see any gaps, at least not with my naked eyes.
On the back, bottom part near the speaker, I don't see it either. Trying to press to see if there is a gap, so far none.
What makes you "scared" on the phone that you have now?
Click to expand...
Click to collapse
Yeah on the front top. I just think water will easily get in the phone...
Sent from my SAMSUNG-SGH-I537 using Tapatalk 4 Beta
I've used this phone below the 1 meter mark and the only bad side effect I get is the microphone not working well for a bit afterwords, which happens really at any level of exposure. This phone is pretty safe in water if you use it correctly.
mattpayne92 said:
...the only bad side effect I get is the microphone not working well for a bit afterwords...
Click to expand...
Click to collapse
That is pretty bad. I mean, I am not going snorkeling and take a phone call while floating on the shore, but if somebody calls me and I CANNOT talk to them because the microphone does not work, that is a big problem.
I am actually wondering how does the phone protects the microphone, earphone and speaker? There are holes there and water can go in. I was considering the Xperia Z and so far the only problem with water issue is the microphone jack - the phone will think that the jack have a headphone but it's only water. However, that is easily fixable by drying it out. I.e. use tissue or something that goes inside the jack.
Microphone though, the holes are to tiny to "dry" with a tissue or something.
BTW, is the microphone STOPS working completely or it works again after a FEW DAYS?
Maybe I can ask those who read this thread to tell me if:
A). You HAVE tested your phone under water (splashing it, dunking it in a bowl of water)
B). What ISSUE you have after you did the above? Phone dead, microphone stops working, etc.
I am trying to get a sense if this is just a specific batch issue (I can replace the phone) or design issue (no matter what, the issue still exists).
If it really was then it would have lifetime warranty. The fact that it only has 1 year warranty like most of the phones tells me that after year 1 be ready to say bye bye to your baby
Sent from my SGH-I337
lanwarrior said:
Maybe I can ask those who read this thread to tell me if:
A). You HAVE tested your phone under water (splashing it, dunking it in a bowl of water)
B). What ISSUE you have after you did the above? Phone dead, microphone stops working, etc.
I am trying to get a sense if this is just a specific batch issue (I can replace the phone) or design issue (no matter what, the issue still exists).
Click to expand...
Click to collapse
Decided to take mine in the shower to test after it got here.
I let the showerhead spray onto the phone, both front and back. Nothing wrong.
Like other people reported, the speaker volume gets significantly lower when wet and goes back to normal within a half hour. Also if the headphone port gets water in it it will errenously display that "headphones are connected" which blowing into the port will fix.
thatbigmoose said:
Decided to take mine in the shower to test after it got here.
I let the showerhead spray onto the phone, both front and back. Nothing wrong.
Like other people reported, the speaker volume gets significantly lower when wet and goes back to normal within a half hour. Also if the headphone port gets water in it it will errenously display that "headphones are connected" which blowing into the port will fix.
Click to expand...
Click to collapse
This is useful! BTW, you haven't test submerging the phone, have you?
maldinimi said:
If it really was then it would have lifetime warranty. The fact that it only has 1 year warranty like most of the phones tells me that after year 1 be ready to say bye bye to your baby
Sent from my SGH-I337
Click to expand...
Click to collapse
No it won't, because all things mechanical / electronics break downs eventually - nothing last forever. Even mil-spec stuff does not have a "lifetime" warranty.
lanwarrior said:
This is useful! BTW, you haven't test submerging the phone, have you?
Click to expand...
Click to collapse
I haven't submersed it yet but there's videos on YouTube with submersion and it brings about the same issues I discussed.
Higher water pressure will clog the mic membrane and make you sound distant in phone calls.
Maybe I'll build up the courage to dunk it tomorrow.
I did the dunk test the night after I got it by fully submerging it in a cup of water...worked just fine afterwards...although I was showing a friend that didn't believe that I had a "water proof/resistant" phone by putting it in the sink and letting water run over it and had an issue with the phone thinking the headphones were plugged in.only did it for about an hour...weird thing was that it didn't start doing it until about 2 hours after it had been wet. Although once it fully dried I haven't had any issues at all with it. Hope this helps.
Sent from my GT-N5110 using XDA Premium HD app
lanwarrior said:
That is pretty bad. I mean, I am not going snorkeling and take a phone call while floating on the shore, but if somebody calls me and I CANNOT talk to them because the microphone does not work, that is a big problem.
I am actually wondering how does the phone protects the microphone, earphone and speaker? There are holes there and water can go in. I was considering the Xperia Z and so far the only problem with water issue is the microphone jack - the phone will think that the jack have a headphone but it's only water. However, that is easily fixable by drying it out. I.e. use tissue or something that goes inside the jack.
Microphone though, the holes are to tiny to "dry" with a tissue or something.
BTW, is the microphone STOPS working completely or it works again after a FEW DAYS?
Click to expand...
Click to collapse
Maybe leave the phone in the sun for a few minutes to dry? Blow on it? Several things help get the water out. But honestly, how often are you going to go swimming with a phone and then take a call immediately afterwards? I'd be thrilled that my phone didn't fry after it fell in the pool, I could care less that the microphone doesn't work for an hour - that's what bluetooth headsets are for.
Anyways, I've had my phone submerged in a sink with running water twice now, the only issues I've found is that after removing the back cover there is water on the outside of the rubber gasket, which looks normal, but I would recommend taking the back off to dry it out after exposed to water.
When i took mine into the pool I made a phone call right after and they said I sounded funny so i blew in the mic and it cleared the water out and they could hear me fine....
geoff5093 said:
But honestly, how often are you going to go swimming with a phone and then take a call immediately afterwards?
Click to expand...
Click to collapse
Not very often, but when I DO need to take that call, it will be a big problem. This is a phone after all.
I don't think I will purposely take the phone for a swim, but the reason I bought the Active instead of the S4 is because of the water/sand protection and want to confirm it works. If it doesn't, then I'll exchange the phone to a normal S4 because it's thinner.
However, based on your response and others, it seems it does offer those protection to a certain degree and the ONLY issue is that the mic may get covered with water and cause the caller not being able to hear me, but this is easily fixed QUICKLY.

[Q] Improving waterproofness

So I got my new Z3C and was thinking: what if we can make flaps and audio port more waterproof?
Doing pressure sensor test I get reading around 1000 and it's increasing by about 30-40 when I press against screen with closed flaps. But it normalizes after 1-2 seconds and goes back to initial reading meaning tiny amount of air escapes. Does it mean my phone is not totally waterproof? Don't know.
Since this phone is just fresh-water proof (meaning no using in pool or sea) and I really want to use it worry-free in all kind of water that I dare to go in myself I really want to improve waterproofness.
I'm not worried about front and back since glass should be all.kind-of-things-proof. This leaves sd card and sim card covers, audio jack, mic holes and speakers.
So what I thought of was to "grease" flaps' rubber o-rings with rubber compatible oil/grease to make better contact with phone body or use some kind of silicone spread around rubber contact area before closing flaps to have semi-permanent seal and be still able to open and scrub extra stuff off without doing much damage.
For audio jack I thought to make some kind of plug - like pressy button but with a bit bigger "head" that has soft sticky rubber underneath so when pressed in it makes a seal with the edge of audio jack or even plug that is covered with silicone all the way.
Speakers and mic holes could be protected with bits of strong adhesive tape - it's easy to get sticky stuff off the glass and it'll be possible to hear some sound even with speakers covered. Not sure about mic holes because side plastic has matte finish but some strong adhesive should still stick?
So the question - has anyone tried something remotely related? Is it thinkable? Have I missed anything important? What materials (grease, silicone) should I use?
If anyone has done something similar? Probably... But no one ever posted about it on this forum. You can use the phone in the sea and swimming pool, as long as you rinse the phone afterwards. As for modifying the phone, I wouldn't do it. It might cause you to lose your warranty.
In terms of waterproofing the phone even more, I'd look at waterproof cases made for other phones with almost similar dimensions and see if you can do something about the case instead.
Sent from my D5803
Dsteppa said:
You can use the phone in the sea and swimming pool, as long as you rinse the phone afterwards. As for modifying the phone, I wouldn't do it.
Click to expand...
Click to collapse
Plenty of stories of people going in the water, damaging their phone and fighting with sony about warranty.
It's hardly modifying, adhesive sticker on glass is easily removed and thin film of silicone should be also easily removable.
Dsteppa said:
It might cause you to lose your warranty.
Click to expand...
Click to collapse
Yeah... getting water inside causes that too.
Dsteppa said:
In terms of waterproofing the phone even more, I'd look at waterproof cases made for other phones with almost similar dimensions and see if you can do something about the case instead.
Click to expand...
Click to collapse
That's the option. But I haven't seen any slim waterproof case that could be comfortably used all the time.
Anyway, curiosity is strong and I'll most likely try different options.
PS. can someone test pressure sensor - is reading staying high when screen is pressed or it fades back to normal with all covers closed?
I've just used mine in pool all weekends since I bought it without any issue and even without afraid of doing that! The same with my wife's Z1!
And I'm contantly opening/closing its usb port due my xposed modules development (debugging purposes)! Maybe some unlucky day I will screw it... who knows!
Ofc we always need to be sure all ports are properly closed before going to have fun!
kalamees1 said:
Plenty of stories of people going in the water, damaging their phone and fighting with sony about warranty.
It's hardly modifying, adhesive sticker on glass is easily removed and thin film of silicone should be also easily removable.
PS. can someone test pressure sensor - is reading staying high when screen is pressed or it fades back to normal with all covers closed?
Click to expand...
Click to collapse
Sorry, I forgot about the pressure sensor part, it's normal that the numbers go back to normal after you lifted your finger, it works like that for everyone.
If my mind serves me right, I've seen Sony ads with the Z3C being thrown in a pool or something similar, so a pool really shouldn't be a problem. And yes of course people will have to fight for their cause at Sony, they won't just put any phone under warranty, else people would exploit that.
Dsteppa said:
Sorry, I forgot about the pressure sensor part, it's normal that the numbers go back to normal after you lifted your finger, it works like that for everyone.
Click to expand...
Click to collapse
I probably expressed myself bit vaguely. Thing is that pressure reading on my phone returns back to normal WHILE HOLDING screen under pressure. Initially pressing screen creates greater pressure inside the phone, reading rises but air escapes quite quickly (1-2seconds) and pressure reading normalises. After releasing finger screen pressure sensor shows lower readings for a second until extra air seeps inside to equalise pressure again.
Hope it's clear enough.
Also, does it mean that I got less waterproof phone that it should be?
I dunno about you but i've been using my camera in the pool for a while now and even for hours at times
Sent from my D5833 using XDA Free mobile app
I've used mine under water as well. OP if you're really worried about it you can send it off to liquipel and have them make the phone even more waterproof

[Q] Humidty sensor activated, how screwed am i ?

Hi all !
I have my Xperia Z3 compact since 6 month, and i used it a lot in shower, i noticed recently that i had some condensation inside the camera, and that the humidity sensor located near the usb port flaps turned pink....
The problem is that i always took care of the flaps being closed, and i was always under the IP conditions ( no detergent, no high pressure,etc).
I checked the flaps, sealing seems completly untampered....
So, i want to send it back under warranty.. but i'm afraid it will come back with "you used it in wrong way, see, the sensor became pink...."
Any advice ?
Thanks
Elipsus
Velocy said:
Hi all !
I have my Xperia Z3 compact since 6 month, and i used it a lot in shower, i noticed recently that i had some condensation inside the camera, and that the humidity sensor located near the usb port flaps turned pink....
The problem is that i always took care of the flaps being closed, and i was always under the IP conditions ( no detergent, no high pressure,etc).
I checked the flaps, sealing seems completly untampered....
So, i want to send it back under warranty.. but i'm afraid it will come back with "you used it in wrong way, see, the sensor became pink...."
Any advice ?
Thanks
Elipsus
Click to expand...
Click to collapse
I had this problem, except I was only using in the rain, you can get the water out without sending it away (Using a hair dryer / airtight bag of rice) It seems like a lot of Xperia Z3C's are faulty in the "Water Proof flaps" part of the phone. If you send it away Son'y will do a pressure test to see whether it is their fault or yours, if you are certain that the flaps where entirely closed then give it a shot - it should be covered under warranty if you have it.
thanks for the reply man,
i have tried the pressure test (in hidden menu) , with flaps closed, when i squeeze the phone, the pressure rise, but go back to normal after a second, even if i keep squezzing it, does this mean the waterproofing is defective ?
Elipsus
Velocy said:
thanks for the reply man,
i have tried the pressure test (in hidden menu) , with flaps closed, when i squeeze the phone, the pressure rise, but go back to normal after a second, even if i keep squezzing it, does this mean the waterproofing is defective ?
Elipsus
Click to expand...
Click to collapse
According to some other threads the pressure should stay up when you press the screen in, meaning that the device is holding the pressure with no leaks, so most likely, yes it is defective. You can try send it in for warranty, as the pressure test that Sony does is basically the same but they use more advanced testing methods.
Sent from my D5833 using XDA Free mobile app
thanks for you advices , i will give a try to warranty
I can't find any water sensors under my flaps on my us version. Where are you guys seeing yours?
Sent from my Xperia Z3 Compact
PuffDaddy_d said:
I can't find any water sensors under my flaps on my us version. Where are you guys seeing yours?
Sent from my Xperia Z3 Compact
Click to expand...
Click to collapse
If you open up the sim card flap which is at the bottom flap (or the right flap if it is laying flat), there is a little square at the very right/bottom and it will either have a white square of paper or a pink/red square of paper inside that little square (the paper will be red / pink if it has been activated by water)
nzzane said:
If you open up the sim card flap which is at the bottom flap (or the right flap if it is laying flat), there is a little square at the very right/bottom ant it will either have a white square of paper or a pink/red square of paper inside that little square
Click to expand...
Click to collapse
Thank you so much - I always wondered what that white square was for. I mistook it for the reset button originally, but that one is yellow.

Categories

Resources