Related
Anyone know how to get the front bezel off this thing?
It's begging for a paint job.
Thx!
and perhaps a generous application of rubber cement. I had ONE creek point when i bought it - annoying but livable enough (plus the fact all the bad hours of xmas I was working I never had time to return it in the 30 day period to best buy). now almost 2 months latter theres three...
theres a teardown thread or two on here somewhere but the search button seems to be failing (or my browser....)
- Will.
It must pop off, but I don't want to be the guy to try it...
In the tear down I remember seeing roughly 10 small philips screws holding it from the inside to the metal sub structure. To tighten it you need to remove the back of the device then you will see the screws running around the perimeter. I also remember the screen is held to the bezel with a form of double faced tape.
waremaster said:
In the tear down I remember seeing roughly 10 small philips screws holding it from the inside to the metal sub structure. To tighten it you need to remove the back of the device then you will see the screws running around the perimeter. I also remember the screen is held to the bezel with a form of double faced tape.
Click to expand...
Click to collapse
Its funny because the guy at Best Buy was trying to pull the back off of the one I returned... No idea why he was trying to yank the back off of it...
I guess if he had succeeded I would have seen the screws..
Funny enough the display model NookColor at my local best buy was practically falling off. When I first looked at the device I nearly did not buy one because of that but then getting one in my hands at B&N changed my mind.
The front bezel is a "tape and cover" paint job. The screen is glued to the frame pretty solid. I had mine apart to fiddle around and to get the back off for a mold. Most of the screws are Torx #5 or #6. Tape it off good and you should be ok as far as the front bezel. The rear and metal frame you can easily get to by proper disassembly.
Here's the zdnet guide,
http://www.zdnet.com/photos/nookcolor-teardown/487636?seq=21
Here's what I did.
You'll need a torx 5. After you unscrews the 2 screws by the sd slot, use your nail along the chamfer corner to lift the back siding up. Then use a credit card to lift the back up and run along the edge to unhinged the back.
techboydino, are you going to make a new front bezel? might be a small after market for such things. I'd pick up a more solid one if the price was right.
actually metal front and back pieces would rock...
- Will.
I would like to see a silicon back cover case that has a kickstand..
WillCameron said:
techboydino, are you going to make a new front bezel? might be a small after market for such things. I'd pick up a more solid one if the price was right.
actually metal front and back pieces would rock...
- Will.
Click to expand...
Click to collapse
I was really considering metal but the fact that most would have to really take special care to actually seperate the bezel from the screen really kind of set me off that. making a case for this is rediculously hard. (compared to my attempts at other devices. if you ever seperated a screen for a cell phone from the glass then you know what I mean. I am trying to replace the back with aluminum and wanted to do a carbon fiber front. so far everything is too thick or just plain looks bad.
Ever heard of masking tape?
3M BLUE painters tape FTW
Glad to find this post!!!
This maybe a little off the subject but does any know where I can purchase a replacement faceplate frame cover.
I accidentally drop my nook color and now it has a nasty crack...
Thank you all in advance!
i took the kickstand off a picture frame...white glued it and had one. Then took it off to fit my new cover...replacement kickstand not put on yet..
nookme said:
This maybe a little off the subject but does any know where I can purchase a replacement faceplate frame cover.
I accidentally drop my nook color and now it has a nasty crack...
Thank you all in advance!
Click to expand...
Click to collapse
Your best bet is probably to pick up a smoked one off EBay or one with a cracked screen and a good bezel.
Actually post up WTB (want to buy) dead Nook Color in the XDA market and link to it in this thread. I seem to recall a couple readers here who have more than "gently used" Nooks....
hey, i was wondering if any one was successful in removing their engravings off the back of the nexus one..... i bought mine cheap second hand, but i can't seem to get the engravings off... thanks!
Maybe if you look up in the dictionary of what "engrave" means you'll find your answer. Then again is it possible to un-grave something? Put a cute little sticker over it or something.
Die grinder.
plastic filler
superfine sandpaper
paint
cover engravings with the filler
let it dry
sand down the filler until it's flush with the rest of the phone
wipe off with a wet rag (let dry after)
paint
depending on your painting skills you can make it look halfway decent. You won't make it like new though. The only way to make it not like terrible would be to paint the entire part of the phone where it is engraved. Since the engravings are on the chrome, looks like a whole body job to me.
Good Luck
Update:
Also, seriously you can't google? You do own their phone...
http://www.ehow.com/how_7774043_remove-engraving-nexus-one.html
I'd do this instead.
Toothpaste or Chocolate to wear it down.
Deekayy said:
Maybe if you look up in the dictionary of what "engrave" means you'll find your answer. Then again is it possible to un-grave something? Put a cute little sticker over it or something.
Click to expand...
Click to collapse
sorry, engrave may not be the correct word to use. this is probably laser etching. i'm talking about the etching that google did for people who wanted to customize their phones.
XSafire said:
plastic filler
superfine sandpaper
paint
cover engravings with the filler
let it dry
sand down the filler until it's flush with the rest of the phone
wipe off with a wet rag (let dry after)
paint
depending on your painting skills you can make it look halfway decent. You won't make it like new though. The only way to make it not like terrible would be to paint the entire part of the phone where it is engraved. Since the engravings are on the chrome, looks like a whole body job to me.
Good Luck
Update:
Also, seriously you can't google? You do own their phone...
http://www.ehow.com/how_7774043_remove-engraving-nexus-one.html
I'd do this instead.
Click to expand...
Click to collapse
i did google and i tried that already. didn't even scratch the surface. and the surface is not chrome, its anodized aluminum. which is a pain in the butt to work with...
Jyveafk said:
Toothpaste or Chocolate to wear it down.
Click to expand...
Click to collapse
i tried the sugar cubes, but i believe thats only for silkscreened logos. i doubt either of these will be able to get the laser etched letterings. thanks though.
anyone else who was able to remove the personalized lettering on the back of the N1?
19.95$ back cover on ebay (real one)
The engraving isn't on the back cover, it's on the metal chassis.
Can you not buy a replacement chassis?
Sure you can, but they're not cheap, and I suspect it's a fair bit of work to swap the parts over.
First, it is important to note that the "engraving" is NOT actually engraved in, as some people here seem to believe.
It is merely silk-screened on.
As for removing it, I would suggest a mild abrasive, like tooth paste, and rubbing it with a cotton cloth... it will probably take a lot of elbow grease, but it should work!*
*Note: not responsible if you damage your phone or kill your loved ones with this method.
ngy said:
i did google and i tried that already. didn't even scratch the surface. and the surface is not chrome, its anodized aluminum. which is a pain in the butt to work with...
Click to expand...
Click to collapse
my bad. If you scratch it with your fingernail, can you feel a groove?
GldRush98 said:
First, it is important to note that the "engraving" is NOT actually engraved in, as some people here seem to believe.
It is merely silk-screened on.
As for removing it, I would suggest a mild abrasive, like tooth paste, and rubbing it with a cotton cloth... it will probably take a lot of elbow grease, but it should work!*
*Note: not responsible if you damage your phone or kill your loved ones with this method.
Click to expand...
Click to collapse
can't say its silkscreen for sure. i took a look under the microscope and its retains the same texture as the rest of the aluminum... silkscreened letterings SHOULD have a different, smooth texture.
XSafire said:
my bad. If you scratch it with your fingernail, can you feel a groove?
Click to expand...
Click to collapse
yeah i do feel a slight bump. so i'm led to think its silkscreen or laser etched, leaning more towards laser etching... which means im stuck.
Rusty! said:
Sure you can, but they're not cheap, and I suspect it's a fair bit of work to swap the parts over.
Click to expand...
Click to collapse
i think i may actually do this in the end. i was suggested to use "contact cleaner" as it deoxides materials... but thats precisely what anodized aluminum is... a thicker layer of colored aluminum oxide. it may just strip it all down to the bare aluminum... argh thinking out loud.
I have heard from someone who have tried the same thing known as Contact Cleaner. Haven't tried personally so can't say for certain but hey, what's the harm in trying it out? I don't have any personalization otherwise would have tried it out.
creativedevil said:
I have heard from someone who have tried the same thing known as Contact Cleaner. Haven't tried personally so can't say for certain but hey, what's the harm in trying it out? I don't have any personalization otherwise would have tried it out.
Click to expand...
Click to collapse
really. contact cleaner can really get the thing off? i should try and get my hands on some then, rather than spending $60+ for a new housing. was thinking of sand blasting the whole thing too... and painting it all back. lol. all black nexus.......
ngy said:
really. contact cleaner can really get the thing off? i should try and get my hands on some then, rather than spending $60+ for a new housing. was thinking of sand blasting the whole thing too... and painting it all back. lol. all black nexus.......
Click to expand...
Click to collapse
Please don't do this.
just sand down the aluminum until it is flush with the rest of it, then use different grades of paper until it is smooth
I don't exactly know how close to perfect you can make it, but it's better then sandblasting it.
ngy said:
can't say its silkscreen for sure. i took a look under the microscope and its retains the same texture as the rest of the aluminum... silkscreened letterings SHOULD have a different, smooth texture.
Click to expand...
Click to collapse
I am 99% sure it is silk-screened on, in a similar manner to the Google and HTC logos on the back.
GldRush98 said:
I am 99% sure it is silk-screened on, in a similar manner to the Google and HTC logos on the back.
Click to expand...
Click to collapse
i sure hope so. i think im gonna try the contact cleaner stuff thats been mentioned. while i have my doubts.... i guess i'll just give it a shot. anyone know what removes silk screening?
I think you would damage the surface of you phone.
Put a sticker over it instead.
Any way to get crap out of the speaker grill I'm kinda ocd about it...
Sent from my HTCONE using xda app-developers app
a very light suction tool.
no vaccuum.. maybe a handheld bulb pump, squeeze and allow it to suck the debris out.
TorxT3D said:
a very light suction tool.
no vaccuum.. maybe a handheld bulb pump, squeeze and allow it to suck the debris out.
Click to expand...
Click to collapse
I just used a toothpick with extreme care, because there is no soft grill, worked good.
You should try one of those baby noise cleaners, great suction and they're cheap.
I've had good luck with a dry toothbrush and light, quick strokes.
you run the risk of forcing it deeper into the holes.
i'd only use a fine bristle art brush for the edges.
suction bulb for holes.
or just put your mouth on it and suck dry and fast.
ive been using those hand held blow thingys used for cleaning debris out of dslr's
The best way is with a toothbrush damped
In alcohol.
Soak the toothbrush in alcohol and dry it about 90% with towel(semi wet, not too dry, not too wet) Brush the grills, The remaining alcohol will clean the gunk on the speaker grills.
From My htc ONE.
Use a magnet
Sent from my HTCONE using Tapatalk 2
i forget what it's called, but i like to use the tacky putty material that is meant to be rolled into a ball to hold posters/photos on a wall.
No magnets are bad...
Sent from my HTCONE using xda app-developers app
I've had mine at least 5 days before most people on here, and I haven't seen anything stuck in the grills of my phone. Does anyone have any pictures they can show? I'd be interested to see how big of a problem this is.
Some tips from reading this post and having this issue
I have a three week old HTC One and untill my recent trip abroad i had not noticed anything slipping into the grills of the phone on my return from spainI put it in my bag along with a bottle of Liquer and a My babys left over fomula powder... Then i dropped the BAG!
Needless to say the combination of the powder and some of the Liquer made for a horrible thick mess which covered my Phone including filling the speaker grills.
I used a toothbrush and this actually did a brilliant Job, its not 100% but i know if I do it a few more times over the next few days it will clear it.
The trick is as stated above careful strokes in one direction across the grill to drag the dirt out using a brush with fine bristles.
Do not put a Magnet anywhere near the speakers on your phone this can cause internal damage which may void your warrenty. Also the suggestion for using some form of blue tac to do this could also go very very wrong, If the tack is too warm it will stick itself into the grill and that will be indredibly difficult to get out if not impossible dependent on how hard you press down trying to remove the dirt, this can also just force the dirt futhur into your device.
The alchol based methord is also very good but be careful too much moisture and you could damage your speaker if it seeps in so its best to dry a dry toothbrush at first and only resort to some cleaning based alchols if you have dirt which simply cannot be lifted. (I will say formula when turned to a paste is incredibnly hard to remove but as with most things does dry after a few hours.)
I used a simple baby wipe on the phone afterwards to remove excess dirt from the grill once the toothbrush had done the job.
A magnet isn't going to harm your phone...
akrod2as said:
A magnet isn't going to harm your phone...
Click to expand...
Click to collapse
A strong moving magnet might.
And I've gotten some... I dunno... stuff stuck in my grill, but it hasn't bothered me, usually, it disappears after a while.
Tape?
Sent from my (M7WLS) HTC ONE.
Ok so I have the silver HTC One and as much as I love it, I can't help but think the front would look bad-ass with the black speaker grills...
I was wondering if anyone has any experience replacing their speaker grills, I remember seeing a drop test video and it popped off. The guy in the video mentioned how it didn't clip back on, it was glued on.
I think if it was easy enough to get a stanley blade in between the grill and the plastic it could just pop off (mine has a gap so it could be quite easy) then it would also help in the future if any scratches happen, just to replace them again...
Thoughts?
thats a good idea, itll be great to know if the speaker grills are repleacable, as they are slightly raised on most phones
I'm just worried incase I order the replacment parts and they are not the same quality as the real HTC One parts. Is there a site that sells genuine parts? They would need to ship to the UK for me though...
Are you out of your mind?
If you are, I'd recommend sandpaper tape and some spray paint. That would probably be easier than disassembly. Maybe even some black nail polish.
Sent from my HTC One using xda premium
couped said:
Are you out of your mind?
If you are, I'd recommend sandpaper tape and some spray paint. That would probably be easier than disassembly. Maybe even some black nail polish.
Sent from my HTC One using xda premium
Click to expand...
Click to collapse
I dont think it will be as bad as you think, this is the video I was talking about:
http://youtu.be/KwE9PGDnlvs?t=1m51s
I know the top may be more difficult to get off because of the camera and I think I will wait a few more months to see if anyone does drop their One and the top part pops off... But it would be interesting to know because this could be useful to those who get any real bad damage to their speaker grills...
The speaker grills are glued to the housing, Removing them shouldn't be hard
Do it and get us some pics
I'm doing it. Are you sure about the glue? I also started a thread about it a couple of days ago.
robt772000 said:
I'm doing it. Are you sure about the glue? I also started a thread about it a couple of days ago.
Click to expand...
Click to collapse
The bottom one is definitely glued, I am not sure about the top one though
Im interested...
Barca009 said:
Ok so I have the silver HTC One and as much as I love it, I can't help but think the front would look bad-ass with the black speaker grills...
I was wondering if anyone has any experience replacing their speaker grills, I remember seeing a drop test video and it popped off. The guy in the video mentioned how it didn't clip back on, it was glued on.
I think if it was easy enough to get a stanley blade in between the grill and the plastic it could just pop off (mine has a gap so it could be quite easy) then it would also help in the future if any scratches happen, just to replace them again...
Thoughts?
Click to expand...
Click to collapse
I agree that the black would look pretty cool. Let us know how this turns out! and take pictures of the process. I myself am curious whats behind the top grill, my speaker on the top is starting to crackle horribly i want to know if it would be possible to replace.
One of mine (the bottom grill) has a small chip in it that really annoys me, so i have ordered a new set. Postage to the UK is quite expensive, but the total was only £24. Not that bad considering its an original part I guess.
Removing the grills shouldnt be too hard, just heat them up with a hot air gun, being careful not to 'cook' the phone and carefully prise the grill up. The gap most people have in the case may be a help here. The new one should just press on. Warm it up, press it down and hold it firmly until cool, with a clamp or strong bulldog clip if you can.
Etradesupply.com sells almost everything for HTC one just so everyone knows if they didn't, u also have a tiny chip in my lower speaker grill, but my case hides it for now so I'm not super worried, but I would love to know if this is possible!!
Sent from my HTC One using xda premium
The grills and the SIM tray are about the only things you can replace. They sell screens, but there is no realistic way to replace them. Even if you could open the phone without marking it, putting it back together is almost impossible.
rovex said:
One of mine (the bottom grill) has a small chip in it that really annoys me, so i have ordered a new set. Postage to the UK is quite expensive, but the total was only £24. Not that bad considering its an original part I guess.
Removing the grills shouldnt be too hard, just heat them up with a hot air gun, being careful not to 'cook' the phone and carefully prise the grill up. The gap most people have in the case may be a help here. The new one should just press on. Warm it up, press it down and hold it firmly until cool, with a clamp or strong bulldog clip if you can.
Click to expand...
Click to collapse
Just for clarification, did you order this from etrade supply? do you have it yet and how is the quality...?
Regards
Zak
Etradesupply quality is very good. I order parts from them and never have an issue.
Heat gun or hair dryer to loosen up the glue should help.
Sent from my HTC One using xda app-developers app
Curious to see if you went through with this.
Sent from my HTC One using xda premium
I bought some etrade silver speaker grills but no longer need them.
If possible please share the whole process heating , removing and fixing the top and bottom speaker grill. Thanks !
Sent from my HTC One using xda app-developers app
Just a tip, do not "paint" the grill. It's impossible to do without stuffing up the holes anyway.. And paint does not stick to aluminium.
You need to anodise aluminium.
Google how to do it but in a nutshell..
1) chemically clean existing aluminium to remove all traces of colour /surface protection. 2)Anodise it to required colour or clear colour
This not only gives you the look you want but makes the surface very hard.
Anodising also is not "on" the surface but part of it so it won't scratch off, block holes etc.
Bare aluminium is very soft and WILL oxidise and go dull. Apart from living in a vacuum or learning to breathe argon gas, you can't stop it.
Anodising MAKES aluminium oxidise and then fill the surface with a dye. This prevents further oxidisation.
Cheers, Marty
Sent from my HTC One using Tapatalk 4 Beta
any luck with replacing the speaker grills?
Just a heads up
I asked about this a different thread and one of the people that replied told me that only the bottom grill is glued in. He said the top is actually screwed in from the back before the back cover is put on. I cant confirm if he was correct, but still good info for anyone planning to try something like this. Can anyone confirm that has purchased these if there are threads in the top grill for it to be screw in?
Unfortunately I got drunk the other day and the next morning I noticed a couple silver dots / a couple small nicks in the circled area below. I can feel them a bit with my finger nail. I tried to cover it up using a permanent marker but it looks like crap. Any way to fix it?
Here's what it pretty much looks like up close.
Please stop this nonsense !
Sent from my Galaxy Note8 using XDA Labs
DeMi-GoD said:
Unfortunately I got drunk the other day and the next morning I noticed a couple silver dots / a couple small nicks in the circled area below. I can feel them a bit with my finger nail. I tried to cover it up using a permanent marker but it looks like crap. Any way to fix it?
Click to expand...
Click to collapse
I cannot see the scratches in your photos, maybe you can try this: https://www.amazon.com/DISPLEX-Scra...pID=51jsbOhc71L&preST=_SY300_QL70_&dpSrc=srch, it did a pretty good job for me hiding some light/medium scratches on the screen.
Cheers~
" Black black black black No. 1 "
nail polish.
or get one of those car paint repair pens. its a 2 in one paint and clear coat varnish pen.
Dejan Sathanas said:
Please stop this nonsense !
Click to expand...
Click to collapse
Lmao.
That looks terrible. Hopefully you'll find a solution to this problem very soon. Must be heart breaking having had to wait so long for you Note 8 then this occurring due to a slight "hiccup".
Sent from my SM-N950U using Tapatalk
Limeybastard said:
That looks terrible. Hopefully you'll find a solution to this problem very soon. Must be heart breaking having had to wait so long for you Note 8 then this occurring due to a slight "hiccup".
Click to expand...
Click to collapse
-Rip DeMi-GoD phone.
cases are a life saver.
bober10113 said:
" Black black black black No. 1 "
nail polish.
or get one of those car paint repair pens. its a 2 in one paint and clear coat varnish pen.
Click to expand...
Click to collapse
Yeah, I thought of this too. My concern is that it wouldn't blend and would have two different looking spots just like the marker did.
Dejan Sathanas said:
Please stop this nonsense !
Click to expand...
Click to collapse
Nonsense? Stop trying to make me seem crazy for wanting to fix a defective spot on a 1k phone. You realize people get chips fixed in their expensive cars? Obviously I just have a higher standard for things I own than the typical person here.
DeMi-GoD said:
Yeah, I thought of this too. My concern is that it wouldn't blend and would have two different looking spots just like the marker did.
Click to expand...
Click to collapse
tape out both sides of the led light/lens and finger print reader as to only have the small 'bridge' between the two sections where your scratches are nit taped. tape off also bottom and top where the camera section meets the body of the phone. make nice and straight tape lines. then paint and varnish the exposed section . it will be barely visible if you do a good tape job. paint black wait for it to be dry enought then , varnish and remove tape after a few minutes when the varnish is still a bit soft. then for the love of god get a case.
bober10113 said:
tape out both sides of the led light/lens and finger print reader as to only have the small 'bridge! between the two sections where your scratches are and tape off also bottom and top. then paint and varnish. it will be barely visible if you do a good tape job. then for the love of god get a case.
Click to expand...
Click to collapse
I'll give it a try. And I've had a unicorn beetle case on it since day 1. I also kept on the back protector that it comes with, put on a screen protector, and even put narrow strips of clear packing tape on the right left and top bezel/frame of the phone and then put it into the case. The camera/finger print area is the only unprotected area on my phone. I actually just now put a piece of scotch tape over the fingerprint reader to protect it from scratches and it still works perfectly.
must have been real unlucky to had it dinged just at the wrong place.
That's what happens when you get arrested for public intox and cops confiscate your phone and put it in a bag with your keys.
So should I paint the whole "bridge" or just the two nicks?
DeMi-GoD said:
So should I paint the whole "bridge" or just the two nicks?
Click to expand...
Click to collapse
maybe the whole thing as it might be less apparent and more cimetric. you could also paint the whole thin bezel to. might protect against future alcohol related endeavours.
I might paint the whole thing. Could I actually make it look as good as it originally is? What do you think about taping it off and spray painting? Idk how to tape off the curved edges of the camera/finger print reader.
DeMi-GoD said:
I might paint the whole thing. Could I actually make it look as good as it originally is? What do you think about taping it off and spray painting? Idk how to tape off the curved edges of the camera/finger print reader.
Click to expand...
Click to collapse
spray paint on such a small surface... i dont know. put at least 3 coats. each coat must be thin and uniform. spray at a far distance.
painting on smooth surfaces usualy requires an enameled paint. U need a paint that will resist chipping and that will cure hard.
https://plaidonline.com/brands/folkart/enamels
as for your taping skills then stick to first picture to keep things simple and straight lined.
you could also use a wide tape and cut out the sections with a sharp razor that you need to paint.
when using multiple coats you need to wait a bit between each so it dries enough. keep in mind you still need to have the total coats to be flexible enough so when you remove tape that it will be removed easily and not chip the section you just painted. maybe practice on a piece of glass before.
anyways just be sure surface is grease free before painting.
bober10113 said:
" Black black black black No. 1"
Click to expand...
Click to collapse
https://youtu.be/vFwYJYl5GUQ