I used FlashTool to flash Sony Z3+ E6553 and now phone cannot power on at all. When I plug in to PC, PC can detect but flashtool cannot flash anymore. The phone was working fine, only has phone lock. Please help revise the phone. Thanks.
citifone said:
I used FlashTool to flash Sony Z3+ E6553 and now phone cannot power on at all. When I plug in to PC, PC can detect but flashtool cannot flash anymore. The phone was working fine, only has phone lock. Please help revise the phone. Thanks.
Click to expand...
Click to collapse
Are you sure that your battery is charged?
Try this: press and hold power and volume up button for 10 seconds and see does the phone vibrate.If vibrate flash again via flashtool.,he should works.
Allek84 said:
Are you sure that your battery is charged?
Try this: press and hold power and volume up button for 10 seconds and see does the phone vibrate.If vibrate flash again via flashtool.,he should works.
Click to expand...
Click to collapse
Battery was fully charged and I've tried that but phone does not response at all to flashtool. When plug in to PC, in device manager under USB controllers, it sees it as SOMC Flash Drive. I think the phone boot is dead.
citifone said:
Battery was fully charged and I've tried that but phone does not response at all to flashtool. When plug in to PC, in device manager under USB controllers, it sees it as SOMC Flash Drive. I think the phone boot is dead.
Click to expand...
Click to collapse
Listen,start flashtool again and hit flash and when pop up windows show press and hold volume down button and connect phone to cable.It should to install so called s1 boot driver(SEMC flash device)Do like I said and see what happends when you connect phone to cable.
If pc install any driver start flashtool again and try to flash again.
Before everything,try to press and hold power and volume up buttoins for more time,about 15 seconds and see did he vibrate.
Allek84 said:
Listen,start flashtool again and hit flash and when pop up windows show press and hold volume down button and connect phone to cable.It should to install so called s1 boot driver(SEMC flash device)Do like I said and see what happends when you connect phone to cable.
If pc install any driver start flashtool again and try to flash again.
Before everything,try to press and hold power and volume up buttoins for more time,about 15 seconds and see did he vibrate.
Click to expand...
Click to collapse
Thanks for your help...The phone was flashed successfully with flash tool with flash file E6553_28.0.A.4.8. After flash done, phone was dead, cannot power on anymore. Now when I tried to flash it again, volume down, insert USB the flashtool show as: Device detected with USB debugging off. It doesn't go to flash mode anymore. I took the back cover off, remove battery connector flex cable and connect it back and try flashing many times but flashtool will not detect phone in flash mode..PC can detect phone because it makes connecting sound on PC but detects as what mode I don't know. In device manager, it doesn't show any device in com port but it shows SOMC Flash Device in USB controllers. I tried to press volume up + power but nothing happened. Once again thanks for your help.
somc flash device means dead boot....its no solution yet for it,sorry
this guy or website promise to repair this dead boot problem via test point look here:
ht_tp://www.vungoc-mobile.com/index.php/unlock/932-repair-boot-unbrick-sony-e6553-xperia-z3
or here
http://www.vungoc-mobile.com/index.php/unlock/932-repair-boot-unbrick-sony-e6553-xperia-z3
citifone said:
Thanks for your help...The phone was flashed successfully with flash tool with flash file E6553_28.0.A.4.8. After flash done, phone was dead, cannot power on anymore. Now when I tried to flash it again, volume down, insert USB the flashtool show as: Device detected with USB debugging off. It doesn't go to flash mode anymore. I took the back cover off, remove battery connector flex cable and connect it back and try flashing many times but flashtool will not detect phone in flash mode..PC can detect phone because it makes connecting sound on PC but detects as what mode I don't know. In device manager, it doesn't show any device in com port but it shows SOMC Flash Device in USB controllers. I tried to press volume up + power but nothing happened. Once again thanks for your help.
Click to expand...
Click to collapse
As I understood, you tried to downgrade. Am I right? I heard that sometimes downgrading causes hard brick. I don't know how to fix it but only option is bringing service.
sone xperia z3+ (E6553) flash after dead
sone xperia z3+ (E6553) flash after dead
sony xperia z3+ e6553 model
flash with this model e6653
it does not start after with it
please help me sir
i did something Stupid and my Z2 Pro dead
there is no fast-boot and no recovery .. only black screen and when i press power button there is a short and long vibration just that and the LED there is flash yellow for 0.1 second
aljthab said:
i did something Stupid and my Z2 Pro dead
there is no fast-boot and no recovery .. only black screen and when i press power button there is a short and long vibration just that and the LED there is flash yellow for 0.1 second[/QUOTE try connecting it to the PC, if it doesn't show anything on PC then just hand it over to the lenovo service center and blame it on the device that it stopped booting :silly:. I thought i had bricked my device but they did something and gave it to me in 3 to 4 days and that was done under the warranty no extra charge and don't confess that I had rooted ur device , If u tell them that they will try to extort money from u :crying:
Click to expand...
Click to collapse
aljthab said:
i did something Stupid and my Z2 Pro dead
e LED there is flash yellow for 0.1 second
Click to expand...
Click to collapse
I have exactly the same, what to do? I installed the dev 44, the rate of established but after 15 minutes, logo is stalled, not waiting until the end of excess freewheeling dev 300, it is not fully established and bug crawled, I rebooted the machine and an endless vibration with green LED :crying:
1 Charging can be a little warm
2. can not be detected pc
3. can not access the fastboot mode
4. when charging, the notification light dies
5. deep flash cable has not helped
sorry my bad english
kerei said:
I have exactly the same, what to do? I installed the dev 44, the rate of established but after 15 minutes, logo is stalled, not waiting until the end of excess freewheeling dev 300, it is not fully established and bug crawled, I rebooted the machine and an endless vibration with green LED :crying:
1 Charging can be a little warm
2. can not be detected pc
3. can not access the fastboot mode
4. when charging, the notification light dies
5. deep flash cable has not helped
sorry my bad english
Click to expand...
Click to collapse
Refer to this http://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ and this http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
same issue with zuk z2
adriano1593 said:
Refer to this http://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ and this http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
Click to expand...
Click to collapse
Hello there... Any solution you found? I am stuck with my zuk z2 in same situation ?? any help ?
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
m_atze said:
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
Click to expand...
Click to collapse
What id shown in unknown device.
Like ven_9102&dev_1234
Maybe with editing quallcom drivers for your device id, you can still install it.
and if luck qpst can recognize it as qualcomm debug mod
Sent from my ZUK Z2121 using Tapatalk
eryenakgun said:
What id shown in unknown device.
Like ven_9102&dev_1234
Maybe with editing quallcom drivers for your device id, you can still install it.
and if luck qpst can recognize it as qualcomm debug mod
Sent from my ZUK Z2121 using Tapatalk
Click to expand...
Click to collapse
Hi,
Thanks for your quick response.
The Hardware ID: USB\DEVICE_DESCRIPTOR_FAILURE
"Error Message": This device has been stopped because it has reported errors. (Code 43)
An error occurred while requesting the USB device descriptor.
m_atze said:
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
Click to expand...
Click to collapse
Alright bro, there is one method you can try.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
I assume your phone is a brick now. The only method you can use is the 9008 unbrick mode. (AKA QBST)
There are a few things you need to prepare before you save ur phone. U need to download the require application that the website provided above, after you set everything up,
make sure you download the latest 2.5 QBST rom,
http://bbs.lenovomobile.cn/z2pro/t554654/
Because ur phone wont be able to enter 9008 through software, thus u need to do the following.
1. Load the content XML fille,
2.Turn off your phone. After it's fully shutdown
3. press and hold the volume up button for 3 seconds
4. press power button while hold the volume up (press it for 0.5second and keep holding it)
5. after 0.5 seconds, plug in the usb right away
6. the QFIL tool should appear the Qualcomm usb QD loader
7. the download button should turn blue
8. flash it and wait for reboot
OtakuLi said:
Alright bro, there is one method you can try.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
I assume your phone is a brick now. The only method you can use is the 9008 unbrick mode. (AKA QBST)
There are a few things you need to prepare before you save ur phone. U need to download the require application that the website provided above, after you set everything up,
make sure you download the latest 2.5 QBST rom,
http://bbs.lenovomobile.cn/z2pro/t554654/
Because ur phone wont be able to enter 9008 through software, thus u need to do the following.
1. Load the content XML fille,
2.Turn off your phone. After it's fully shutdown
3. press and hold the volume up button for 3 seconds
4. press power button while hold the volume up (press it for 0.5second and keep holding it)
5. after 0.5 seconds, plug in the usb right away
6. the QFIL tool should appear the Qualcomm usb QD loader
7. the download button should turn blue
8. flash it and wait for reboot
Click to expand...
Click to collapse
Thanks for your tip.
I followed your described procedure, but the phone will not be recocnized by the PC.
1st: I loaded QFIL XML file. (By the way this tut is made by me)
2nd: I disconnected the battery (The phone can't be turned off normally!)
3rd, 4th, 5th
6th: nothing happend!
7th: "-"
8th: "-"
The only way the phone will detected by the PC:
1st: disconnect battery
2nd: plug in USB (PC and Phone)
3rd: press VOL+ or VOL- or PWR button (doesn't matter which one)
4th: connect battery
5th: detected as "unknown usb device (device descriptor request failed)"
m_atze said:
Thanks for your tip.
I followed your described procedure, but the phone will not be recocnized by the PC.
1st: I loaded QFIL XML file. (By the way this tut is made by me)
2nd: I disconnected the battery (The phone can't be turned off normally!)
3rd, 4th, 5th
6th: nothing happend!
7th: "-"
8th: "-"
The only way the phone will detected by the PC:
1st: disconnect battery
2nd: plug in USB (PC and Phone)
3rd: press VOL+ or VOL- or PWR button (doesn't matter which one)
4th: connect battery
5th: detected as "unknown usb device (device descriptor request failed)"
Click to expand...
Click to collapse
Make sure you have to plug in the usb right away as soon as you u press power, and keep holding them
OtakuLi said:
Make sure you have to plug in the usb right away as soon as you u press power, and keep holding them
Click to expand...
Click to collapse
Yes, I did exactly you described. Sorry but this isn't working.
I don't know what I should do. Even a repair shop couldn't fix it.
Maybe I need to do this:
http://bbs.lenovomobile.cn/z2/t121791/?highlight=900e
But I don't want to destroy my PC (3000 bugs)
m_atze said:
Yes, I did exactly you described. Sorry but this isn't working.
I don't know what I should do. Even a repair shop couldn't fix it.
Maybe I need to do this:
http://bbs.lenovomobile.cn/z2/t121791/?highlight=900e
But I won't destroy my PC (3000 bugs)
Click to expand...
Click to collapse
oh well, good luck
OtakuLi said:
oh well, good luck
Click to expand...
Click to collapse
I will report the result.
OK. I made the deepflash cable.
After using it there is no difference between pressing one of the button combinations I recently mentioned (VOL+ or VOL- or PWR).
The phone will be detected as Unknown device. After intalling my modified driver to match the unknown ID, QFIL don't detect the COM Port.
Hello had the same problem, only with the difference that my battery was not completely discharged.
What has helped:
1 Start QFIL Tool
2 Press the volume +
3 Connect the original cable to the PC
4 QFIL Tool recognized the phone and I could play an original Rome.
Mfg
Ps. Is now the battery cover (glass) broken?
No, I used a hairdryer, a razorblade, plastic tool and a suction cup to lift the backcover glass.
The glass is fully intact no damages.
You have good nerves. I would not have expected that.
But in the end, it does not matter if it does not start anymore.
Thank you again for your great instructions for playing and rooting the mobile phone.
I hope you get your phone back.
Mfg
Good and bad news
The guy unbricked the phone successfully, I received it today.
Now I have an other problem:
The phone is very very slow and laggy now.
The problem occurs everywere, Recovery, boot (the bootlogo laggs), booted System, also the test mode laggs now
Furthermore the sceen flickers sometimes and at the right side the sceen is mirrored sometimes.
Did anyone has an idea?
What I did today:
reflash through qfil
1.9.104_ST
2.3.044_ST
ZUI_2.5.335_ST
Hi m_atze, I am exactly in the same situation as You. After using deep flash cable method, I got "unknown usb device (device descriptor request failed)". Could You tell me what was the solution to unbrick the phone?
Hi, I live in Brazil, and I bought a zuk z2pro and without wanting to delete the internal memory of the cell phone, now it is only in black with zuk written in white.
Qfil does not recognize the communication port.
Miflash is just the error.
I do not know how else to do it, please help me.
Use the 9008 method to flash the offical rom on it.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
Here is the link for you. This happened to me before, u need to download all the requirement tools in order to reflash the system.
There is a trick in order to get into 9008 mode.
U need to turn off the phone, turn on the 9008 program on ur computer, and select all the required options on the program with the contest.xml file loaded. Then you hold the phone's volume up for at least 3 seconds, then press the power button for 0.5scond. As soon as you press the power, plug in the usb to the phone, then you should see the 9008 port is available on ur 9008 program.
Hello Masters Im A Noob want ur help.....!!!! i tried to flash miui7 rom bt shamescool and as a result my zr is dead flashtool pc companion wont detect my device plugging usb only red light light appears but nothing else pc not detecting.... someone said me its a dead boot and related to hardware i have c503 locked bootloader rooted and dual recovery installed plz help me to fix it
Remove battery, plug usb in PC, and back battery with press volume down.
yes i did it all but still no hope. i connect with pc holding volume down only red light no flashmode pc doesnt detect and in fastboot mode only blue light pc doesnt detect i actually installed miui7 rom and result got bricked. if someone help plz
I heared here nd there that there is a method to get rid of such situation some guy was talking about testpoints....!!! I dnt know about this i want ur help
Do you instaled all the drivers for flashing ?
Yes drivers installed correctly....
anybody plz show us how to connect testpoint for xperia zr
Check this link , it worked for me https://forum.xda-developers.com/xperia-z/help/unbrick-xperia-z-charging-booting-t2685139