Related
This is really bugging me but on occasion, when I slam the keyboard shut, the phone turns off. It also has happened when I opened the keyboard but only a few times.
I actually dissassembled the phone to see if maybe it was a loose connection somewhere. I did find that the keyboard ribbon cable was loosely connected so I reseated it firmly...but the problem didn't go away.
I also thought it may be either the SIMM card or the memory card contacts but after removing them, again, I still can reproduce the problem.
Understand that this is an intermittent problem and a little unpredictable but I can make it happen within a few tries. If I cautiously open and close the keyboard (without slamming it shut), I have no problems.
I don't believe it's software related because I can force it to happen when the device is booting up (with the Ericsson logo on the screen) before the OS loads.
Anyone else experiencing this?????
11/17/08 UPDATE: PROBLEM RESOLVED!
After further review and testing, it appears that the battery was losing connection to the battery contacts. I shoved a small crumb of paper folded up (about 1mm thick) at the back of the batt and the problem has gone away. Of course, I'm still holding my breath every time I open and close the keyboard but it looks like that may have been the problem. That's strange because I'm using the original battery. Thought this may help in case anyone else ever runs into this.
That sounds like a problem with the internals, maybe a you should get it replaced/repaired?
Kid says to doctor " IT hurts when I twist my arm backward like this." Doctor replies "then don't do that"
You say "my phone shuts off when I slam my keyboard shut" Doctor says "don't slam your keyboard shut"
this thought just made me laugh.
Seriously though. It does sound like an internal hardware issue that you should have fixed otherwise it may just get worse and start happening more regularly and at very inconvenient times.
Good luck.
Reminds me of my samsung slider phone the day that it died. I was sliding it back and forth.. sometimes the screen would go completely white and then come back.
By the end of the day, it went white and stayed that way.
Turns out the cable on the inside was slowly being cut from rubbing against the metal hole it was going thru every time the slider moved.
You've checked the cables before... but maybe its not cut yet, but something on the slider mechanism is hitting a wire/pulling on it.
Nobody knows.
But we all do know thats not normal. So yea get it replaced.
LOL!
hotrod101 said:
Kid says to doctor " IT hurts when I twist my arm backward like this." Doctor replies "then don't do that"
You say "my phone shuts off when I slam my keyboard shut" Doctor says "don't slam your keyboard shut"
this thought just made me laugh.
Seriously though. It does sound like an internal hardware issue that you should have fixed otherwise it may just get worse and start happening more regularly and at very inconvenient times.
Good luck.
Click to expand...
Click to collapse
That's funny!!!
I think you're right...
Nippero said:
Reminds me of my samsung slider phone the day that it died. I was sliding it back and forth.. sometimes the screen would go completely white and then come back.
By the end of the day, it went white and stayed that way.
Turns out the cable on the inside was slowly being cut from rubbing against the metal hole it was going thru every time the slider moved.
You've checked the cables before... but maybe its not cut yet, but something on the slider mechanism is hitting a wire/pulling on it.
Nobody knows.
But we all do know thats not normal. So yea get it replaced.
Click to expand...
Click to collapse
Yep...It's going back. Might as well get a fresh one. I know this problem existed for other phones before and the fix was mostly something simple that didn't require a replacement.
im getting exactly the same problem. gonna send mine back as well.
i have the exact same problem too! Waiting for a new one...
i thought i was the only one with this problem, but it looks like a production error as there are already 3 people on this board who have this defect.
technillion said:
This is really bugging me but on occasion, when I slam the keyboard shut, the phone turns off. It also has happened when I opened the keyboard but only a few times.
I actually dissassembled the phone to see if maybe it was a loose connection somewhere. I did find that the keyboard ribbon cable was loosely connected so I reseated it firmly...but the problem didn't go away.
I also thought it may be either the SIMM card or the memory card contacts but after removing them, again, I still can reproduce the problem.
Understand that this is an intermittent problem and a little unpredictable but I can make it happen within a few tries. If I cautiously open and close the keyboard (without slamming it shut), I have no problems.
I don't believe it's software related because I can force it to happen when the device is booting up (with the Ericsson logo on the screen) before the OS loads.
Anyone else experiencing this?????
11/17/08 UPDATE: PROBLEM RESOLVED!
After further review and testing, it appears that the battery was losing connection to the battery contacts. I shoved a small crumb of paper folded up (about 1mm thick) at the back of the batt and the problem has gone away. Of course, I'm still holding my breath every time I open and close the keyboard but it looks like that may have been the problem. That's strange because I'm using the original battery. Thought this may help in case anyone else ever runs into this.
Click to expand...
Click to collapse
yep, my problem seems to have gone now as well by using you're method. i was almost ready to send it back and then i saw you're post and tried your method and it worked !
Thats a pretty stupid mistake by SE...
They should do a quick fix by making new batters a smidge thicker. Of course they probably wouldn't offer free replacements, but they should fix it anyway.
technillion said:
11/17/08 UPDATE: PROBLEM RESOLVED!
After further review and testing, it appears that the battery was losing connection to the battery contacts. I shoved a small crumb of paper folded up (about 1mm thick) at the back of the batt and the problem has gone away. Of course, I'm still holding my breath every time I open and close the keyboard but it looks like that may have been the problem. That's strange because I'm using the original battery. Thought this may help in case anyone else ever runs into this.
Click to expand...
Click to collapse
Where did you place the paper exactly ? On the back of the battery where all the info text is or on the bottom ?
When my device is cold, eg in the morning for first use, this sometimes doesnt happen for >20x tries...but when i used it for a longer time and it almost always shuts down when slammed shut..but i already thought it might be something with the battery, but sometimes while slamming it shut for numerous times even the battery cover would come up and it didnt shut down...then in another situation it shuts down immediatly
Poor design...
toxical said:
Where did you place the paper exactly ? On the back of the battery where all the info text is or on the bottom ?
Click to expand...
Click to collapse
Yea...what I found with the design is that the ribbon cable connecting the keyboard sits right under the battery. In fact you can see the protrusion when you remove the battery under the white label. It moves when the keyboard is opened and closed. Slightly...but it does move.
...anyway...I folded a small piece of paper to wrap around the back edge of the battery.
Try this:
1. Make a small rectangular strip of paper about 10mm x 20mm and fold it the long way so you end up with a 5mm x 20mm piece.
2. Wrap it around the back/bottom edge of the battery as you reinsert it.
(If the battery fits more snug in its compartment, you got it right!)
3. Put the back cover back on--which should also be more snug.
4. Turn on the device and try it out (slam the keyboard).
(You don't have to wait for it to completely boot up...you can test it when the SE logo appears).
Be careful to use regular copy paper and not paper that's too thick as it may cause some other damage/problems with the device.
could you make a picture of that ?
Actually i will recieve a new device tomorrow, but i still have the feeling that this problem might reoccur as it seems to be a design flaw
technillion said:
11/17/08 UPDATE: PROBLEM RESOLVED!
After further review and testing, it appears that the battery was losing connection to the battery contacts. I shoved a small crumb of paper folded up (about 1mm thick) at the back of the batt and the problem has gone away. Of course, I'm still holding my breath every time I open and close the keyboard but it looks like that may have been the problem. That's strange because I'm using the original battery. Thought this may help in case anyone else ever runs into this.
Click to expand...
Click to collapse
I'm currently playing around with an old XV6800 I got off ebay, and this seems to have fixed the problem, so thanks
I had the same problem too.. but it was linked with the flex cable. Now i just don't use my keyboard even after fixing it.
Hi!
was working night shift. when I looked on the ground and noticed that the screen on my phone was on. so I graped it to turn it of, when I realiced that it wasn't the screen but the flash on the back next to the camera. its not as bright as when the flash is actually turned on in the camera menu. and the only way I found to turn it of is by pulling the battery out, anyone had/has a similar problem.
Michael
there was someone else who had a post about this before - search "light always on" or something like that but there was a recent post with someone who had the same problem
I did a search. not that i didn't do so before. the only thing that came up was for a different phone (wizard) not for Xperia. been looking around now for the last couple days and haven't been able to find anyone else with a similar problem. well at least on the internet.
any one else
Michael
dreamsaga said:
I did a search. not that i didn't do so before. the only thing that came up was for a different phone (wizard) not for Xperia. been looking around now for the last couple days and haven't been able to find anyone else with a similar problem. well at least on the internet.
any one else
Michael
Click to expand...
Click to collapse
went back through each page looking for it
http://forum.xda-developers.com/showthread.php?t=541959
Twas on page ten - but it looks like it never came to a conclusion... sorry dude
I wonder if he/she did ever fix it. well if I can't fix it soon I will have to take it back to the shop.
Edit: after posting I did another search and wolla. found this http://forum.xda-developers.com/showthread.php?t=485701 . this might explain it a liitle bit. after reading does posts I think I better not wast my time. since it really looks like a hardware issue
well. send it off to three on monday. they called me back yesterday.
the LED is allways on due to the wiring on the main board being corroded. we have disconnected the wire. because the damage is from corrosion we can't fix it under warranty. we are sending it back to you today.
were did the corrosion come from. its never been anywere near water.
dreamsaga said:
were did the corrosion come from. its never been anywere near water.
Click to expand...
Click to collapse
Sweat (perspiration lol)?
or maybe if you live near the ocean?
When lights are always on like that it does usually mean there was or is some trace of liquid on the circuits or on the led itself.
When you receive the phone, try disassemble it and clean the corroded circuit with alcohol and it should be good, if its only the short causing the led to always receive power.
That sucks though...
I was the first to post about this issue. 4 months on or so and I still have the same problem. The light has remained on all the time since then, although not as high intensity a when the flash is on. It's no big deal, you get used to it, like the led lights on the side of the phone. I'd also like to say this has not impacted on the flash whatsoever. It still works
DirtyVadah said:
I was the first to post about this issue. 4 months on or so and I still have the same problem. The light has remained on all the time since then, although not as high intensity a when the flash is on. It's no big deal, you get used to it, like the led lights on the side of the phone. I'd also like to say this has not impacted on the flash whatsoever. It still works
Click to expand...
Click to collapse
You mean to say that it has been running non-stop(minus restarts) for 4 entire months???
thats good news for me to know the LED is so durable.
so you haven't tried disassembly and cleaning it yourself, the corrosion that is. I taken my x1 apart already and its not that hard, just have to be gentle.
Yep. Although remember the intensity is not that high as when you switch on the flash to take a pic. And actually even though the phone is off the led remains on. It's the battery you need to take out. So it's been on constantly for the past 4 months.
same problem
dreamsaga said:
well. send it off to three on monday. they called me back yesterday.
the LED is allways on due to the wiring on the main board being corroded. we have disconnected the wire. because the damage is from corrosion we can't fix it under warranty. we are sending it back to you today.
were did the corrosion come from. its never been anywere near water.
Click to expand...
Click to collapse
so did you ever solve this problem? i have the exact same issue with my xperia. Any help would be appreciated.
Hey guys i just bought a nook color and had it shipped to my country but i think i am already regretting it now.
The touch screen starts behaving very weird randomly at any times, it automatically registers touches and keyboard automatically typing own it own, and what ever i touch just goes straight to hell and this continues as long a i don't lock and unlock it again.
Even when i am reading it automatically starts zooming.
I was think about rooting it and installing a custom Rom, will that fix the problem? because giving it back to B&N is not an option for me.
Also i don't have screen guard, and the screen is always smudged with fingerprints, can that trigger this sort of behavior?
I'm using mine in Australia and have a similar problem but only when using the supplied USB cable to charge it.
I've heard stories about faulty USB cables which might be the case as I don't have this problem when I use the cable for my desire. The problem with this is that the cable isn't long enough for practical use and the supplied cable apparently has extra pins which would explain why it still discharges (although slower) when using my desire micro USB cable.
For now I'm limited to only using my nook without the cable plugged in but I'm thinking about finding another cable as sending it back to B&N and then paying to ship it back here isn't really a viable option.
Let me know if you figure something out though.
Well the one with usb cable is a known issue and u can still use it otherwise, mine just happens randomly at any time, its almost unusable.
Does installing a custom rom help?
It wouldn't hurt to try. I know some kernals make changes to the touchscreen sensitivity but I don't know whether that would apply to your problem or not. A nook is very easy to un-root anyways so as far as I know (and don't quote me on this), you should be able to return it if you absolutely have to.
Don't give up though. I'm loving mine and for the price it's an awesome little accessory when it works.
Hi,
Make sure to clean the touch screen - last night I had a different looking
smudge on my screen that was causing huge problems - as soon as I cleaned
it off, back to normal. Are you in a humid location? Condensation will cause
problems too.
Also you may want to search for 'calibrate' in the forums, there is a way to
recalibrate the touchscreen sensitivity, I believe that this is mostly for
low sensitivity at the corners though.
Here are two links I found:
http://forum.xda-developers.com/showthread.php?t=943358&highlight=calibrate
http://forum.xda-developers.com/showthread.php?t=934500
Good luck!
Peter
My touch screen acts up as well. I turn the screen off for a couple minutes to "reset" it. It will work OK for a little, then it goes back to wonky.
Hey guys i finally found a solution to this problem, well my touch screen is behaving normally when its not not connected to the power cable. I hope thats a solution good enough for you.
Just go to
h**p://nookdevs.com/Recalibrate_the_NookColor_touch_screen
I tried all the custom roms but that didn't help very much, so i tried this on CM7
and so far my screen is giving totally normal tests results when not plugged in and lets hope that it stays that way.
My daughter had a similar wonky-screen problem when she plugged in a particular set of portable music player speakers. Not another pair she has, just that one.
And I was able to replicate it on my nook. It wasn't specific to her nook.
okay, it seems that my excitement didn't last that long but
After a lot of testing, it turned out that the only problems was my oily or moist fingers.
so i got a screen guard and tested it for more than two hours and i haven't had any problems yet. So even if i do see that happening again, once in two hours is not that bad.
rigy73 said:
okay, it seems that my excitement didn't last that long but
After a lot of testing, it turned out that the only problems was my oily or moist fingers.
so i got a screen guard and tested it for more than two hours and i haven't had any problems yet. So even if i do see that happening again, once in two hours is not that bad.
Click to expand...
Click to collapse
I think I'll try this cause I have oily fingers as well and I'm getting the wonky screen issue while NOT plugged in as well.
rigy73 said:
Hey guys i finally found a solution to this problem, well my touch screen is behaving normally when its not not connected to the power cable. I hope thats a solution good enough for you.
Just go to
h**p://nookdevs.com/Recalibrate_the_NookColor_touch_screen
I tried all the custom roms but that didn't help very much, so i tried this on CM7
and so far my screen is giving totally normal tests results when not plugged in and lets hope that it stays that way.
Click to expand...
Click to collapse
I'd add my vote to this link...worked for me:
http://nookdevs.com/Recalibrate_the_NookColor_touch_screen
Assumes you have ADB working via USB or wireless
NOTE: THIS SOLUTION IS POTENTIALLY DAMAGING AND MAY NOT WORK FOR EVERYONE
PROBLEM: touch screen acts erratic, notification bar keeps opening, screen appears to be touched by someone else continuously (Ghost Touch), and parts of the screen DO NOT RESPOND TO TOUCH.
MY OWN SPECIFIC CASE: I had the Ghost Touch issue for 3 days suddenly without intro, which often used to go away after a reboot or two, then phone worked normally after I removed the battery and left it in a dry area (in a closed drawer between books, no air entering, very dry atmosphere), however the RIGHT SIDE of the screen (Search button, rightmost letters [L and Delete and sometimes ENTER] do not work. If the phone is in normal landscape, you cannot open the notification bar by dragging it normally.
DIAGNOSIS: for some people, the problem is more severe. The Digitiser itself could be malfunctioning and has to be fixed, while for others it could be a true problem with the screen itself. However, for MANY OF US, it is a problem of HUMIDITY. The humidity sensors are causing the phone to act like that. Some say part of this problem happens because the way the keypad affects the phone internally as you open and close it a lot.
SOLUTIONS:
1- To be safe: send the phone to the shop. Ask them to open the phone and apply an extra layer of insulation, in case the digitiser and the screen are okay.
2- If something is faulty, replace it at the shop.
3- MY OWN SOLUTION: based on something I read many times, the solution was to apply DRY HEAT for at least 45 mins. What I did, based on averaging out many experiences I read online, was to remove the SD Card and SIM, remove battery, I heated up a toaster oven for 10 minutes, waited until the temperature was at about 60-70 degrees Celsius, SHUT DOWN THE HEAT, put the phone on its screen on a plate, screen facing down and covered by a cloth to protect it from direct contact with metal, then all inside the oven. The oven is a relatively big one, so phone was AWAY FROM A SOURCE OF DIRECT HEAT. I closed the lid, then every while 15 minutes I would heat the oven for 40 seconds to maintain the temp. This is LIKE (ALTERNATIVE SOLUTION) leaving your phone in the glove compartment of your car while its parked in a sunny spot, to find it really hot in the morning and tough to touch for a while. TO CONTINUE, after the phone was out of the oven (I can't believe I am saying this), I left the phone overnight in a dry area for 8 hours (could need less time). Then, I put everything back in, plugged it, and THE PHONE IS WORKING PERFECTLY NOW!
NOTE that solution number 3 could affect your keyboard buttons if heat is too much. It may cause the glue holding the keys to melt a bit. Be delicate with your keyboard after you restore your phone.
Again, I only did this YESTERDAY. With the exception of some keypad stickiness, the phone is working perfectly now.
I hope this was useful
B.
EDIT: Today is the First of May, phone is still working without a glitch
N.B. Press the Thank you button if you wanna congratulate me on daring to toast my milestone in the name of scientific inquiry
SECOND EDIT: Phone did it again for 2 days. Applied the same method, and it worked again. I think partially it happened because I was in a very humid location.
That didn't work for me, I had no option but to replace the touchscreen/gorila glass.
I love the idea of toasting a milestone
Thought with all my aggression against Moto, I think I just might leave it in there
Luckily I dont have these problems so I wont get tempted
AirLancer said:
I love the idea of toasting a milestone
Thought with all my aggression against Moto, I think I just might leave it in there
Luckily I dont have these problems so I wont get tempted
Click to expand...
Click to collapse
I have to admit, I cared litte whether or not this actually worked. I just wanted to toast it But it did work, so
Pretty tempted to try this out, I think I will when I have free time.
My phone had the dead zone problem for 2 months now, but in some very rare cases, like when it's a very hot day, the screen will work normally for a minute or something. Then it goes back to dead part. I assume this would fix it?
Lesiroth said:
Pretty tempted to try this out, I think I will when I have free time.
My phone had the dead zone problem for 2 months now, but in some very rare cases, like when it's a very hot day, the screen will work normally for a minute or something. Then it goes back to dead part. I assume this would fix it?
Click to expand...
Click to collapse
If it DOES indeed work on hot days, then it means the phone is not entirely dead. But I would suggest you do something less drastic first, such as the Glove Compartment method. No responsibility though
If you're trying to remove moisture, you could also try putting it in a baggie of crystaline cat litter (NOT the clay kind!) - this stuff is sold at a MUCH higher price as a way to save a phone from water damage, but it's the exact same substance. Does a great job removing moisture. It's the same sort of silica gel that's in those packets in medicine/vitamins that says "Dessicant - do not eat".
Or you could just put it in a sealed bowl with raw rice for a couple of days... this is the best and cheapest way (and then you have the silicon "grains", the ones that you find in shoe boxes or computer parts boxes).
Sent from my Milestone using Tapatalk
CybeRNerO said:
Or you could just put it in a sealed bowl with raw rice for a couple of days... this is the best and cheapest way (and then you have the silicon "grains", the ones that you find in shoe boxes or computer parts boxes).
Sent from my Milestone using Tapatalk
Click to expand...
Click to collapse
Pretty sure that rice doesn't do anything, I don't know how that started as a suggestion, but its not better than anything else; its not known to be absorbant, but the silicon is.
I've tried the method but the right segment of the digitizer still doesn't work.
My biggest issue with regards to "lack of responsiveness" are the 4 capacitive buttons. Pressing the Home key is always hit and miss. I know I hit it all the time because I can feel the vibration feedback but it only goes to homescreen 50% of the time.
Will also be testing this out as soon as I have the spare time. My screen started acting up after I accidentally put my milestone in a small beer spill at a party Hopefully this will work out for me too!
Abazel said:
I've tried the method but the right segment of the digitizer still doesn't work.
Click to expand...
Click to collapse
Luckily for me, I was still under warranty, heh. Cause I had insurance. This is my second Droid this has happened to. Hopefully my replacement won't do the same thing.
How many times did you reheat the oven? I tried just once and it didn't help. My phone has been having this problem since January.
decon89 said:
How many times did you reheat the oven? I tried just once and it didn't help. My phone has been having this problem since January.
Click to expand...
Click to collapse
I feel I am on a cooking show
Well, depends on your over. Mainly I was trying to maintain a temp varying between 50-60 c. Mostly 50, but sometimes 60 to up the ante a bit and make sure things stay warm. 30 minutes at least. However, I have to say that I did this twice in 6 weeks, and after that the phone just died again, and I found my warranty card and sent it there to be fixed, and they fixed it, but ruined something else.
If you have the warranty card, take your phone and send it to them Someone told me the method worked and the phone has been good for quite a while, but most of us seem to re-experience the issue after a while.
I've been having these issues for a few days now too, and I think I know why. I've been using this Milestone for 4 months now, and I never had this problem until a few days ago. What I noticed yesterday was that after some acting up, the phone started working properly again. So I ran Touch Test. And I noticed that if I pressed really hard on the top side of the phone(where the logo and the ear piece are located) it started acting up again. My first impression was that the glue holding down the gorilla glass was loose. So I left the phone as usual on my night stand and then I tried the same thing with the pressing on the same area. Guess what? It didn't happen again. Now there seems to be no problem. So I tried to remember what happened yesterday before the screen started acting up, and I remember talking to my wife for a while when I was in my car. Yesterday was a pretty hot day and I was a little sweaty when I talked to her. Now since only that specific part with the earpiece was causing this issue(I tried pressing equally hard on other areas without any problem my guess is that the insulation between the earpiece and the touchscreen has been breached. Maybe because of all the sweat that went in there in time. You know the salt and acids in the swear are known to melt things, and poor quality glue is among them.
How to fix this? I do not know yet, but I do have a good idea that I'd like to share. I want to buy a screen protector foil, and put just a little band around the ear piece. That would probably lower my in-call volume, but since the Milestone is very loud anyway I hope it the quality of the calls won't be too much affected. After that I'll use it in normal conditions again and see if the ghosting happens again.
try completely formatting your SD CARD/PARTITION.
& then reinstalling using (FAT 32/EXT 2, 3, or 4)
sometimes traces from the previous ROM might interfare with touch codecs (maybe)
just trying to help. had similar issue & this is what i did.
bandroid842 said:
NOTE: THIS SOLUTION IS POTENTIALLY DAMAGING AND MAY NOT WORK FOR EVERYONE
PROBLEM: touch screen acts erratic, notification bar keeps opening, screen appears to be touched by someone else continuously (Ghost Touch), and parts of the screen DO NOT RESPOND TO TOUCH.
MY OWN SPECIFIC CASE: I had the Ghost Touch issue for 3 days suddenly without intro, which often used to go away after a reboot or two, then phone worked normally after I removed the battery and left it in a dry area (in a closed drawer between books, no air entering, very dry atmosphere), however the RIGHT SIDE of the screen (Search button, rightmost letters [L and Delete and sometimes ENTER] do not work. If the phone is in normal landscape, you cannot open the notification bar by dragging it normally.
DIAGNOSIS: for some people, the problem is more severe. The Digitiser itself could be malfunctioning and has to be fixed, while for others it could be a true problem with the screen itself. However, for MANY OF US, it is a problem of HUMIDITY. The humidity sensors are causing the phone to act like that. Some say part of this problem happens because the way the keypad affects the phone internally as you open and close it a lot.
SOLUTIONS:
1- To be safe: send the phone to the shop. Ask them to open the phone and apply an extra layer of insulation, in case the digitiser and the screen are okay.
2- If something is faulty, replace it at the shop.
3- MY OWN SOLUTION: based on something I read many times, the solution was to apply DRY HEAT for at least 45 mins. What I did, based on averaging out many experiences I read online, was to remove the SD Card and SIM, remove battery, I heated up a toaster oven for 10 minutes, waited until the temperature was at about 60-70 degrees Celsius, SHUT DOWN THE HEAT, put the phone on its screen on a plate, screen facing down and covered by a cloth to protect it from direct contact with metal, then all inside the oven. The oven is a relatively big one, so phone was AWAY FROM A SOURCE OF DIRECT HEAT. I closed the lid, then every while 15 minutes I would heat the oven for 40 seconds to maintain the temp. This is LIKE (ALTERNATIVE SOLUTION) leaving your phone in the glove compartment of your car while its parked in a sunny spot, to find it really hot in the morning and tough to touch for a while. TO CONTINUE, after the phone was out of the oven (I can't believe I am saying this), I left the phone overnight in a dry area for 8 hours (could need less time). Then, I put everything back in, plugged it, and THE PHONE IS WORKING PERFECTLY NOW!
NOTE that solution number 3 could affect your keyboard buttons if heat is too much. It may cause the glue holding the keys to melt a bit. Be delicate with your keyboard after you restore your phone.
Again, I only did this YESTERDAY. With the exception of some keypad stickiness, the phone is working perfectly now.
I hope this was useful
B.
EDIT: Today is the First of May, phone is still working without a glitch
N.B. Press the Thank you button if you wanna congratulate me on daring to toast my milestone in the name of scientific inquiry
SECOND EDIT: Phone did it again for 2 days. Applied the same method, and it worked again. I think partially it happened because I was in a very humid location.
Click to expand...
Click to collapse
Thank you for that Solution.
It fixed the Issue of my friends MS without other problems
I'll have to try and the oven methode again. My phone has started to really act up again.
I've tried to install new roms, wipe ect. and it doesn't help with the screen.
Have anyone tried to replace the digiziter? They are pretty cheap on ebay
My milestone started freaking out just an hour ago. No more warranty here but I'm not brave enough to do the oven method. Had anybody tried the Rice alternative?
I flashed a cyan build delta using the app cyandelta the other day and after that, the phone refused to charge unless it was turned off. I figured the build had broken something but discovered that the phone would hang when trying to boot into twrp. So i did a full reset using the 1.29 ruu to see if that would help and it did not except now i get a warning on screen saying the usb host is unplugged and unable to change in the notification area.
the stock build also suffers from other random quirks like during phone call it repeatedly turns on and off the speaker phone and the gyro sensor will randomly turn my screen sideways.
took it into the sprint store and said there was corrosion on the charging port but i know it has not gotten wet at all the past few days and that the problem occurred right after the flash.. They refuse to touch the phone and say i have to pay 150 to replace it. I have tried cleaning the port with a dry toothbrush to no avail
Is there anything else i can try and re flash that might fix some messed up software or was flashing the ruu the best bet.
Thanks for your time and help
-shadow
Had the EXACT same issue on mine, never unlocked or rooted. Sometimes the volume would just disappear as well (even when using headphones) but the Beats icon would still show. Everything would go into permanent landscape mode at times. Calls answered in speaker automatically. If I plugged it in while it was on I got the usb host notification. The car mode app thingamajig launched for no flippin' reason, had to turn it off to charge it, all that jazz.
Definitely a hardware issue with the usb port. I took mine to Sprint hoping for a replacement but it has a barely visible crack horizontally across the screen so that was denied unless I agreed to pay the $150 deductible. It flew out of a car with me about a month prior so that did some damage to the phone. Then I dropped it the day these issues started happening. The port felt loose, I figured all of the wear and tear messed it up.
I didn't actually fix the phone though. It just randomly started working smoothly again and I haven't had a problem with it since - it has been a couple of months now. From all of the research I did, I saw that most people had the problem just fix itself for no reason and never come back. I tried cleaning the port and poking and prodding but nothing fixed it. Just one day, BOOM, all better.
Hope it decides to behave soon
Sent from my HTCONE using Tapatalk 2