Related
Hi,
I have a HTC wizard and recently when i was using it the screen went blank. (i lost my original charger and had to get a replacement Moto Razr Mini USB charger since my town dosnt even have a proper store!!!)
I ended up charging the phone for a while and then when i disconnected the charger to use the phone it just went blank and will not turn on anymore. Even the Battery Charging (orange) LED will not turn on. What do i do? should i get a new battery? or should i try getting another charger?
thanks
Kandarp said:
Hi,
I have a HTC wizard and recently when i was using it the screen went blank. (i lost my original charger and had to get a replacement Moto Razr Mini USB charger since my town dosnt even have a proper store!!!)
I ended up charging the phone for a while and then when i disconnected the charger to use the phone it just went blank and will not turn on anymore. Even the Battery Charging (orange) LED will not turn on. What do i do? should i get a new battery? or should i try getting another charger?
thanks
Click to expand...
Click to collapse
Search for battery fix...
--M
Kandarp said:
Hi,
I have a HTC wizard and recently when i was using it the screen went blank. (i lost my original charger and had to get a replacement Moto Razr Mini USB charger since my town dosnt even have a proper store!!!)
I ended up charging the phone for a while and then when i disconnected the charger to use the phone it just went blank and will not turn on anymore. Even the Battery Charging (orange) LED will not turn on. What do i do? should i get a new battery? or should i try getting another charger?
thanks
Click to expand...
Click to collapse
assuming it was working properly before it crashed, you will probably have to either find someone else with a wizard and have them charge your battery for you, buy a new battery put it in the phone, boot up and leave it connected to the USB for a full day to charge it up completely. Search the forums for the 9V battery revival trick, it may help you get booted up and be able to save the cost of a second battery.
dont get a battery a waste of time
the problem is the charger I have confimed this. In my environment we have about 10 Razors and 20 MDA's. This is a common complaint amougst our users. The motorola charger don't work on the MDA'S. I promise you if you get another charger it will work. Also if you plug your sync cable in to a pc it will charge this should prove my point.
Recently my X1 cannot be charged with USB cable through wall outlet & even car charger , but able to charge with USB cable through PC.
Anyone do encounter the same problem?
Well that's a strange one - how long was it connected to the wall?
Without getting into the discussion about volts and amps provided, and amps drawn by the phone, any method should charge.
In terms of speed, I would think the wall would charge fastest (see above), and the USB slowest.
Did the phone show on the top bar, the charging icon when attached to the wall? Or after a period of time there was no increment in the % charge showing??
If the battery was down to 0%, you probably wouldn't see an immediate increase in the % charge. The % charge is orientative, especially at both ends of the scale.
paul c said:
Well that's a strange one - how long was it connected to the wall?
Without getting into the discussion about volts and amps provided, and amps drawn by the phone, any method should charge.
In terms of speed, I would think the wall would charge fastest (see above), and the USB slowest.
Did the phone show on the top bar, the charging icon when attached to the wall? Or after a period of time there was no increment in the % charge showing??
If the battery was down to 0%, you probably wouldn't see an immediate increase in the % charge. The % charge is orientative, especially at both ends of the scale.
Click to expand...
Click to collapse
I do agree with you. Charging with wall outlet is faster. Therefore, normally I'm charging my X1 with wall outlet, unless in office, will use PC USB.
Top bar never show charging icon, but once I charge it with PC USB, the charging icon show up immediately.
It seems like no power for the USB when connected to the wall outlet. I've tested with battery removed, plugged in USB cable connected to wall outlet, there is no charging illumination light. I cannot power on it.
I tried to recall, it happened after I used a USB charger for my MP3 player. The next day, when I tried to charge with car charger. To my surprise, the USB connection notification showed up (I do remember, while charging with wall outlet or car charger, it will never prompt me for USB connection).
I don't think, it is the ROM issue. Try a few ROM still having the same problem.
From now, I got to live with PC USB :|
X1 Charging problem
I have same problem. I can not charge via both USB-PC and Wall. In order to charge the phone, I have to switch it off and then charge it.
This happened after I used CHEAP car charger from dealexteme.com
Now everytime I want to charge my phone, I have to switch it off.
torquefever said:
I have same problem. I can not charge via both USB-PC and Wall. In order to charge the phone, I have to switch it off and then charge it.
This happened after I used CHEAP car charger from dealexteme.com
Now everytime I want to charge my phone, I have to switch it off.
Click to expand...
Click to collapse
let's me try with power off charging with wall outlet
well thats why se said USE only original accessories...you need to change the power ic on the board.
donottouch said:
well thats why se said USE only original accessories...you need to change the power ic on the board.
Click to expand...
Click to collapse
will the SE service centre entertain changing 'power ic'?
make sure your charger have an out put minimum is 1.Ah ,if lest than that it will not work , that is the troublem
nguyennghiep said:
make sure your charger have an out put minimum is 1.Ah ,if lest than that it will not work , that is the troublem
Click to expand...
Click to collapse
I'm using the original SE charger!? I would not think the problem with the charger, but my X1 was screwed by the incompatible MP3 USB charger
Yep same with me, not sure why mine started doing that though, I never got used a cheap charger. Maybe its the rom... I am trying a new one now.
torquefever said:
I have same problem. I can not charge via both USB-PC and Wall. In order to charge the phone, I have to switch it off and then charge it.
This happened after I used CHEAP car charger from dealexteme.com
Now everytime I want to charge my phone, I have to switch it off.
Click to expand...
Click to collapse
digitalspree said:
Yep same with me, not sure why mine started doing that though, I never got used a cheap charger. Maybe its the rom... I am trying a new one now.
Click to expand...
Click to collapse
it's not caused by the ROM, I'm very sure. I've installed different ROM. The problem still exist.
I am having a similar problem. When the phone completely discharges , i am unable to charge it with any power adapter or even car charger. I have to initially charge the phone using a PC , then after the power is around 15% , then the phone gets charged with a normal adapter.. any suggestions??
same problem. It happends when the battery is completely discharged.
what I do is use a charger w/ low amp rating (.1) and plug it in for at least 10-20min. Give it some time, it will start charging after a while (indicated by the blinking lights). After that, you can turn it on and charge it normally
I had a similar problem twice.Both times I solved it by replacing the charger.
the same happen to me and i have another issue
my xperia doesnt work as usb mass storage!!!
the solution was buying another charger but..the usb mass storage issue still not working as a flash drive!!
luirhy said:
same problem. It happends when the battery is completely discharged.
what I do is use a charger w/ low amp rating (.1) and plug it in for at least 10-20min. Give it some time, it will start charging after a while (indicated by the blinking lights). After that, you can turn it on and charge it normally
Click to expand...
Click to collapse
It works with Z1 too. Thanks a lot!
I guess something goes wrong with battery controller
Hi.
My xda stellar is not charging but in a very strange way...
The orange led is glowing and in power menu i get the "charging" notification but in fact the device is not charging... :S What's wrong??
I think that it happened after i tried to charge the device using a motorola charger. I don't have the original charger i used to charge it with an htc mini usb charger that i had.
The pins of the usb port seem ok...
For the moment i'm charging the battery outside of the device.. :/
Any suggestion?
Could be an old dried used up battery.
I tried a second one(new) that's not working too.....The device was working perfectly until i tried the motorola charger..
Hey, I'm having the same problem and I seeing as i brought the phone second hand it didn't come with an official charger and just used the USB mini i have laying around. Again I have replaced the battery thinking it was that. Nada. Still doing it.
I've taken the phone apart and cannot see anything wrong.
So I was wondering until the problem is solved, how are you charging the battery externally?
Thanks
My battery totally died last night and powered off when it ran out of battery however now I cannot charge the phone at all. It was on charge all night and no charging light comes on. Ive tried with the mains cable, usb cable to pc and in car charger.
Does anyone have any suggestions to get it working again?
Thanks
Did it just randomly die? Is there anything you did beforehand that could influence it, like dropping it (in water)?
I'm not entirely sure what it could be, but if you could provide this info, others mide have an easier time troubleshooting.
dr9722 said:
My battery totally died last night and powered off when it ran out of battery however now I cannot charge the phone at all. It was on charge all night and no charging light comes on. Ive tried with the mains cable, usb cable to pc and in car charger.
Does anyone have any suggestions to get it working again?
Thanks
Click to expand...
Click to collapse
HI
greetings,
connect the phone to charger and press and hold the power button for 30 sec and see if the led is flashing
if not then connect to pc and try to boot into bootloader menu and tell what happens. weather it boots, does it just vibrates or does the led flash
this is a problem on Xperia Devices (at least the ones with a sealed battery my x10 never had this).
This drain brick happens because the hell i know, but is phone bricked, dark, no light , no vibration, nada, its was a real brick.
how i fixed it? sort of i fixed my Xperia T had to provoke charging but the Z1 doesnt have a red blinking light after charging it for a while... but it does have a magnetic charging port!.
now to the instructions. following what i did to try and revive my phone.
1. try to charge the phone for an hour or so.
2. most like it wont charge but if you connect it to the PC, it will sort of react to it, just try unplugging and plugging the phone till it reacts, you may even leave it to charge there just in case (for about 10 mins if you want i leaved it for 3).
3. get a 2 AMP charger, the original one or a known brand charger like anker (i did it with my anker charger and it worked).
4. get or Use a magnetic cable/dock and connect it simultaniously with the usb cable on the PC. (and no the magnetic cable wasnt enough to jump charge the phone).
5. if the stimulation worked, it should be able to show a really dim red led, that means your phone is still alive
6.let it charge it will turn on alone.
7. smile and cry out of joy because your 500-700 dollar phone still works.
if it worked or you have any modifications on this method leave a comment and hit the THANKS button.
btw i turned on my phone and it had 1% that means it never charged until i jump charged it.
Interesting. For normal charging, will plugging the Z1 to the USB and magnetic ports simultaneously speed up charging as well?
Celestial Fury said:
Interesting. For normal charging, will plugging the Z1 to the USB and magnetic ports simultaneously speed up charging as well?
Click to expand...
Click to collapse
no you can't speed up charging. Charging speed is limited to cable quality, AC plug quality and software/hardware restrictions.
the USB on PC and magnetic cable combo for some reason helps to start the phone like you do when you want to recharge an depleted car battery.
It just open the circuit and let the phone charge again.
someone please confirm if this works for more than one person/situation.
Thanks for assistance btw, hopefully it works for all of us.
Nope doesn't work.
I tried it already.
Sorry guys.
Worked for me. Took some time before PCC registered it though.
help me please
Asadroid said:
this is a problem on Xperia Devices (at least the ones with a sealed battery my x10 never had this).
This drain brick happens because the hell i know, but is phone bricked, dark, no light , no vibration, nada, its was a real brick.
how i fixed it? sort of i fixed my Xperia T had to provoke charging but the Z1 doesnt have a red blinking light after charging it for a while... but it does have a magnetic charging port!.
now to the instructions. following what i did to try and revive my phone.
1. try to charge the phone for an hour or so.
2. most like it wont charge but if you connect it to the PC, it will sort of react to it, just try unplugging and plugging the phone till it reacts, you may even leave it to charge there just in case (for about 10 mins if you want i leaved it for 3).
3. get a 2 AMP charger, the original one or a known brand charger like anker (i did it with my anker charger and it worked).
4. get or Use a magnetic cable/dock and connect it simultaniously with the usb cable on the PC. (and no the magnetic cable wasnt enough to jump charge the phone).
5. if the stimulation worked, it should be able to show a really dim red led, that means your phone is still alive
6.let it charge it will turn on alone.
7. smile and cry out of joy because your 500-700 dollar phone still works.
if it worked or you have any modifications on this method leave a comment and hit the THANKS button.
btw i turned on my phone and it had 1% that means it never charged until i jump charged it.
Click to expand...
Click to collapse
Hello my friend I have Xperia Z1 and I fall into the Hard Brick Pc didn't recognized my phone but I put myself in the wall charger after a few hours LED red blinking you can post a picture for this solution because I did not understand exactly and thank you
pheel said:
Nope doesn't work.
I tried it already.
Sorry guys.
Click to expand...
Click to collapse
did the computer detected the phone but for a brief moment like trying to install the drivers?
Kirkymole said:
Worked for me. Took some time before PCC registered it though.
Click to expand...
Click to collapse
@Kirkymole;
can you share what you did exactly and what i can up to the guide?
and im glad that i could help you
momo-infos said:
Hello my friend I have Xperia Z1 and I fall into the Hard Brick Pc didn't recognized my phone but I put myself in the wall charger after a few hours LED red blinking you can post a picture for this solution because I did not understand exactly and thank you
Click to expand...
Click to collapse
as i told you on the PM write up how you bricked it exactly and what steps have you done so i can help you correctly.
i will post pictures of the procedure of how i did it when i get a few hours to edit and upload it.
Tried this trick last night. After 2 hours LED stopped blinking and became stable RED (no flashing). This is the first time in 1 month that LED stopped flashing, I was even able to Hold Power+Volume up button and it vibrated 3 times (nothing like that happened in the past). So it was a significant improvement from where I was 2 days ago. However, LED suddenly turned off and when I connected it to charger again it started to blink again. Buttons do not respond again.
Little info from the past:
I bricked my Z1 when I flashed .290 ROM. Left it on charge for 2 days nothing happened, flashtool would not recognize it and kept saying USB debugging off. Then I decided to open back cover and remove the battery so it could reset. That didnt resolve the issue and i just gave up.
Video instruksion would be very helpfull maybe
Asadroid said:
did the computer detected the phone but for a brief moment like trying to install the drivers?
Click to expand...
Click to collapse
Yes. But the computer simply recognised it as a normal "unknown" usb device with usb debugging disabled.
--
ruinkhan said:
Tried this trick last night. After 2 hours LED stopped blinking and became stable RED (no flashing). This is the first time in 1 month that LED stopped flashing, I was even able to Hold Power+Volume up button and it vibrated 3 times (nothing like that happened in the past). So it was a significant improvement from where I was 2 days ago. However, LED suddenly turned off and when I connected it to charger again it started to blink again. Buttons do not respond again.
Little info from the past:
I bricked my Z1 when I flashed .290 ROM. Left it on charge for 2 days nothing happened, flashtool would not recognize it and kept saying USB debugging off. Then I decided to open back cover and remove the battery so it could reset. That didnt resolve the issue and i just gave up.
Click to expand...
Click to collapse
Exact same thing happened to me. "USB debugging off"
All I did was plug in the magnetic connector, then with the PC turned on and Pc companion running I plugged in the USB, it took about 20 minutes to recognise it but once it did, I unplugged it, left it on charge via the magnetic plug for around 5 hours and although the charging symbol never appeared it booted into recovery the normal way (I did that just to see what would happen) then restarted the phone via Cwm and it worked normally from then on.
Kirkymole said:
although the charging symbol never appeared it booted into recovery the normal way .
Click to expand...
Click to collapse
BY saying "Charging Symbol never appeared", do you mean LED was not red and turned off?
ruinkhan said:
BY saying "Charging Symbol never appeared", do you mean LED was not red and turned off?
Click to expand...
Click to collapse
The symbol that appears on the screen.
I also kind of used this method.
I directly plugged in, in these steps.
1) Plug in magnetic charging dock with 1A charger (Plugged USB into charger)
2) Plug in USB with 2.1A charger (Plugged USB into charger)
Dim-ish red light popped up and the phone began booting.
Plugging into the phone for me wasn't as effective as plugging into the charger as I left it for a while and nothing happened but upon plugging USB into my single dual port charger this method worked to get my phone onto the charging screen, Android L
Had to plug the USB in and out a few times, not too many times, but eventually it booted up to the charging screen.
Be patient is the key I suppose?
For me worked with magnetic and usb 1A charger! Thanks!