So the thing is, I decided to buy this phone from another person a few days ago while it was still working but it had this one problem where the owner told me about how the phone can't be shutdown unless the battery runs out of power. Any time you shut it down, it simply reboots instead. I thought it was most likely a problem I could fix after flashing, so I decided to buy it.
Using Flashtool I was able to see that if timed pressing the buttons and plugging it into my computer right before the reboot started, I could boot into flashmode. This phone came in the 4.4 KK firmware and the 10.5.1.A.0.292 Generic NCB build, so I flashed an older kernel and rooted it using Towelroot before reflashing the 10.5.1.A.0.292 Generic NCB kernal. After rooting (and testing if root apps can shut it down which didn't work either), with a locked bootloader I installed the XZDualRecovery using the method here because I was finding it so hard to unlock the bootloader and Flashtool wouldn't do it either. It automatically booted into TWRP recovery menu but when I tried to flash a ROM (existenz Ultimate 3.5 to be precise), it simply made the screen go black for a second and took me back to the recovery menu. So figuring it was a bad download, I downloaded a smaller ROM but when I rebooted I accidentally went into PhilZ Touch menu instead. Deciding to do the usual wipe before flashing, here's where I messed up like an idiot. I saw an option along the lines of "Wipe CLEAN for flashing ROM" or something and trusted it so much despite it saying it's gonna wipe the system partition clean as well (I still don't know why I accepted even when warned of that).
So basically now I have a system that boots the SONY splashscreen and then goes black with the back light still on unless the battery runs out. I can't shut it down no matter how long I hold the power button and if I restart, it boots back to the same thing. I have no recovery menu now thanks to my genius idea of wiping the system, and the only thing I can enter is flashmode. So when I try to flash an FTF firmware (I tried every firmware I could get) back into the phone with Flashtool, it would simply say "preparing for flashing" for about a minute before it says "device disconnected" because the phone decides to exit flash mode and boot normally. I have a locked bootloader (with bootloader unlocking allowed), so I can't flash recovery menus. When I try booting by holding the VolumeUp key and plugging it in, it enters flash mode only with the red LED on and I still get the same results on Flashtool.
Was wondering if there were any ways around this that I might have missed before deciding to open the phone and change the hardware? And if it comes to that, what would I need to change (have always been a software guy when it comes to phones)? Any tips and advice would be appreciated.
TLDR: Have a bricked c6603 from wiping the system, that can't shutdown and keeps rebooting and refuses to be flashed.
If you have time before the phone reboots, hold Volume UP and the power key for 15 seconds. The phone will vibrate once at 10 seconds. Keep holding the keys until you feel 3 vibrations. This will hard power down the phone.
Sent from my C6603
^I've tried this and it simply boots back up again.
Hmm. That should definitely shut the device down, not restart it.
Sounds like there could possibly be an issue with your power button. I've heard of issues with the power button after water damage. Have you checked the water ingress indicators under the flaps? If any are red, it points to earlier damage from water.
Sent from my C6603
kingvortex said:
Hmm. That should definitely shut the device down, not restart it.
Sounds like there could possibly be an issue with your power button. I've heard of issues with the power button after water damage. Have you checked the water ingress indicators under the flaps? If any are red, it points to earlier damage from water.
Sent from my C6603
Click to expand...
Click to collapse
Seems like you're right, I just checked it and it indeed has a faded red color on it. Do you think if I take the phone apart it the power button could be fixed or should I swap something else inside this from another Xperia?
7ty6er said:
^I've tried this and it simply boots back up again.
Click to expand...
Click to collapse
I experienced this problem
Pls hold down volume When u connect your phone to pc via flashtool,
It will connect in flash mode
After that , just flash 0.230 kernel via flash mode ( kernel not rom )
Then disconnect your phone
Turn it off ( hold power button and volume up till it vibrates 3 times )
Then before it turn on again , hold down the volume down and connect it to pc via usb and this time flash 0.283 Rom ( not kernel )
This worked for me
Related
After searching around I couldn't find anything related so here's my problem.
After succesfully unlocking the bootloader of my Xperia Z it continues to work fine.
It prompted the initial startup screen (enter language, account info ect.)
I turned my device off and on... this is where the problem starts..
This is what i get
Sony brand logo>
Xperia brand logo>
5 repeated cloud animation of xperia logo and at the last one it stalls, Phone reboot and back to 0.
This goes on repeatedly until a hard poweroff or complete discharge ( I suppose)
So I know im kinda screwed, is relocking the bootloader any option? Contacting Sony atm for some sort of software replacement/flash anything..
Cheers, Geert
Try the safe mode,keep pressing vol down with power until the phone boot completely.
If the phone boot to safe mode than do a factory reset.
Sent from my C6602 using xda premium
GeertNool said:
After searching around I couldn't find anything related so here's my problem.
After succesfully unlocking the bootloader of my Xperia Z it continues to work fine.
It prompted the initial startup screen (enter language, account info ect.)
I turned my device off and on... this is where the problem starts..
This is what i get
Sony brand logo>
Xperia brand logo>
5 repeated cloud animation of xperia logo and at the last one it stalls, Phone reboot and back to 0.
This goes on repeatedly until a hard poweroff or complete discharge ( I suppose)
So I know im kinda screwed, is relocking the bootloader any option? Contacting Sony atm for some sort of software replacement/flash anything..
Cheers, Geert
Click to expand...
Click to collapse
Welcome to XDA
you should go to the recovery thread in my signature. Read the first 2 posts.
Hope you recover your phone.
Hi everyone !
I have the same problem as GeertNool. My Xperia is stuck in the same loop. I have tried everything.
- Flashboot : stuck at 0% when i try to flash
- Pc Companion and SEUS = dead ends
- Safe mode : cant make it work
I read the recovery thread. It seems that the Kernel is malfunctioning but i dont understand what should be my next move. Am i supposed to let the phone reboot endlessly untill eventually the battery dies ?
Thanks a lot for your precious answers.
Alex
al3xwhite said:
Hi everyone !
I have the same problem as GeertNool. My Xperia is stuck in the same loop. I have tried everything.
- Flashboot : stuck at 0% when i try to flash
- Pc Companion and SEUS = dead ends
- Safe mode : cant make it work
I read the recovery thread. It seems that the Kernel is malfunctioning but i dont understand what should be my next move. Am i supposed to let the phone reboot endlessly untill eventually the battery dies ?
Thanks a lot for your precious answers.
Alex
Click to expand...
Click to collapse
Yes.
When the battery dies the phone should reset itself.
After the loops end plug into a charger, not pc for now.
You should get a red led indicating low battery level charging is working.
After the red led you may get Sony boot screen or bootloops.
If you get Sony and then the charging battery icon, then charge to over 50%. Then use pc companion or flashtool to restore.
If you get bootloops then read my 2nd post from the recovery thread in my signature for bootloop tricks.
Please let me know if it works. I am looking to add the Xperia Z to my recovery guide.
If there are any questions about my guide please ask in that thread.
Thanks
From Jaramie's LT28at
Try this: hold power and VolUp for about 15 seconds. The device should vibrate 3 times in a row. It should now be off. Don't plug it in anywhere.
Download the correct flashtool beta for xperia z http://forum.xda-developers.com/showthread.php?t=2162907
Download a known-to-work firmware ftf
Put it into C:\Flashtool\Firmwares
Open flashtool (flashtool64 if you run 64bit Windows)
Chose Flash (flash arrow button)
Chose the ftf you downloaded
Enable "Wipe: Data, Cache, Appslog"
Click flash
A new window opens with a "press back button" animation
Now plug in the device while ONLY holding VolDown. Only VolDown, no Power. The LED should turn green.
Don't interrupt the flashing process. It will take a while.
Report back if it worked.
after flashing rom my xperia is booting until the lock screen appears then it resets. what should i do? thanks
vaud27 said:
after flashing rom my xperia is booting until the lock screen appears then it resets. what should i do? thanks
Click to expand...
Click to collapse
Did you flash it with flashtool?
Did you enabled "Wipe: Data, Cache, Appslog.?
Sent from my C6602 using xda premium
gm007 said:
Did you flash it with flashtool?
Did you enabled "Wipe: Data, Cache, Appslog.?
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
i use cwm to flash it. i wipe everything. after flashing the recovery disappear and my xperia keeps on rebooting after reaching the lock screen.
can i reflash it using flashtool even my usb debugging is off?
vaud27 said:
i use cwm to flash it. i wipe everything. after flashing the recovery disappear and my xperia keeps on rebooting after reaching the lock screen.
can i reflash it using flashtool even my usb debugging is off?
Click to expand...
Click to collapse
Something wrong with the rom you are trying to install.
Yes you can use flashtool even if usb debugging is off.
Check schaggo post up^^^^
Sent from my C6602 using xda premium
gm007 said:
Something wrong with the rom you are trying to install.
Yes you can use flashtool even if usb debugging is off.
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
i will try to flash it using flashtool. thanks for your help mate
had the same problem and i managed to fix it just showing sony sign by installing the sony update programme on the sony update website
all you do is put phone into flashboot mode.
on mine i had to hold up and power button untill it vibrates 3 times then press down volume button to get it into flashboot mode
takes a few atempts but it worked.
takes around 20 mins to download then install another 10.
i couldnt get flashtool to flash firmware as my phone is locked on 3 mobile firmware locked bootloader
i hope this helps you
update:
schaggo method works. i can breath now. thanks to @gm007
This worked great for unbricking mine !!
P.S. don't waste time for Sony's Emma flash, they do not send login credentials in real time, site says they do manual user validation ...
schaggo said:
Try this: hold power and VolUp for about 15 seconds. The device should vibrate 3 times in a row. It should now be off. Don't plug it in anywhere.
Download the correct flashtool beta for xperia z http://forum.xda-developers.com/showthread.php?t=2162907
Download a known-to-work firmware ftf
Put it into C:\Flashtool\Firmwares
Open flashtool (flashtool64 if you run 64bit Windows)
Chose Flash (flash arrow button)
Chose the ftf you downloaded
Enable "Wipe: Data, Cache, Appslog"
Click flash
A new window opens with a "press back button" animation
Now plug in the device while ONLY holding VolDown. Only VolDown, no Power. The LED should turn green.
Don't interrupt the flashing process. It will take a while.
Report back if it worked.
Click to expand...
Click to collapse
AW: [Q] Xperia Z possible brick
racht said:
...don't waste time for Sony's Emma flash, they do not send login credentials in real time...
Click to expand...
Click to collapse
They never will. Read the instructions which come with EMMA. I have it working fine, officially, without any credentials.
flashtool not flash the phone
schaggo said:
Try this: hold power and VolUp for about 15 seconds. The device should vibrate 3 times in a row. It should now be off. Don't plug it in anywhere.
Download the correct flashtool beta for xperia z http://forum.xda-developers.com/showthread.php?t=2162907
Download a known-to-work firmware ftf
Put it into C:\Flashtool\Firmwares
Open flashtool (flashtool64 if you run 64bit Windows)
Chose Flash (flash arrow button)
Chose the ftf you downloaded
Enable "Wipe: Data, Cache, Appslog"
Click flash
A new window opens with a "press back button" animation
Now plug in the device while ONLY holding VolDown. Only VolDown, no Power. The LED should turn green.
Don't interrupt the flashing process. It will take a while.
Report back if it worked.
Click to expand...
Click to collapse
I have the same issue here, the phone suddenly dead. Charge it using AC adaptor and wall socket and the red led flashs for about 2 hours, the orange LED never turns on. Try your advice and got this:
1) Vol up + Power not work (no vibration, nothing)
2) Flash with flashtool 0.9.10.2 beta6 with no lucky, indicated "device disconnected" after animation gone.
3) regress to flashtool 0.9.10.1, device connected and then stuck at "flashing data.....", the progress bar stay at 0% and then nothing.
P.S. bootloader is still locked but phone is ROOTED so I'm affraid it's out of warranty. Just got the phone as a birthday gift from my wife yesterday! She'd kill me if she knows that.
Update:
1) Power + Vol Up works now. The sequence does matter, I found I have to press the Power button first and then Vol Up, it dosen't work vise versa.
2) flashing still doesn't work for me. And I noticed that the LED turn green and then turn off immediately. I'm not sure if that is the cause. I'm sure when in fastboot mode (connect to USB port when pressing Vol Up), the LED turn blue and stay blue. Is my flash mode corrupted?? That's really bad!
[email protected] said:
I have the same issue here, the phone suddenly dead. Charge it using AC adaptor and wall socket and the red led flashs for about 2 hours, the orange LED never turns on. Try your advice and got this:
1) Vol up + Power not work (no vibration, nothing)
2) Flash with flashtool 0.9.10.2 beta6 with no lucky, indicated "device disconnected" after animation gone.
3) regress to flashtool 0.9.10.1, device connected and then stuck at "flashing data.....", the progress bar stay at 0% and then nothing.
P.S. bootloader is still locked but phone is ROOTED so I'm affraid it's out of warranty. Just got the phone as a birthday gift from my wife yesterday! She'd kill me if she knows that.
Update:
1) Power + Vol Up works now. The sequence does matter, I found I have to press the Power button first and then Vol Up, it dosen't work vise versa.
2) flashing still doesn't work for me. And I noticed that the LED turn green and then turn off immediately. I'm not sure if that is the cause. I'm sure when in fastboot mode (connect to USB port when pressing Vol Up), the LED turn blue and stay blue. Is my flash mode corrupted?? That's really bad!
Click to expand...
Click to collapse
Try sony update service or remove flashtool and install again and use another firmware(maybe the first one is corrupted).
Sent from my C6603 using xda premium
[email protected] said:
P.S. bootloader is still locked but phone is ROOTED so I'm affraid it's out of warranty. Just got the phone as a birthday gift from my wife yesterday! She'd kill me if she knows that.
Update:
1) Power + Vol Up works now. The sequence does matter, I found I have to press the Power button first and then Vol Up, it dosen't work vise versa.
2) flashing still doesn't work for me. And I noticed that the LED turn green and then turn off immediately. I'm not sure if that is the cause. I'm sure when in fastboot mode (connect to USB port when pressing Vol Up), the LED turn blue and stay blue. Is my flash mode corrupted?? That's really bad!
Click to expand...
Click to collapse
It probably means your battery was low.
From my Xperia LT28at ION
gm007 said:
Try sony update service or remove flashtool and install again and use another firmware(maybe the first one is corrupted).
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
Thanks for response. Finally flashtool 0.9.10.1b works for me!
Returning to stock
Hey guys,
I've flashed [ROM][JB 4.2.2][CM10.1][AOKP-MR1][PananoidAndroid 3.15] PAC v22.1.1 - Update: 0508 from http://forum.xda-developers.com/showthread.php?t=2208249&page=65. It's working, but I'd like to try another ROM, specifically Xperia Z Revolution™ from http://forum.xda-developers.com/showthread.php?t=2175903. This requires to install stock 10.1.A.1.434 firstly So I downloaded C6603_10.1.A.1.434_Generic DE, NL, world. Flashing with Flashtools 0.9.10.1 always stucks at 0%.
BL unlocked. Does anyone have any idea how to get stock 434 in the phone? Originally there were older one 10.1.A.1.340, if it's somehow important to know...
I finally found solution! Bootloader on my phone isn't nearly same as usual one, no white screen, just a few lines which designate modes. 4 are present:
-normal boot
-fastboot
-recovery
-UART boot
I accessed it by pressing and holding power button and volume up button at the same time during device boot.
I hope someone with a same problem will find this helpful!
I managed to boot to system but I still can't get in bootloader. No combos and neither adb works.
I got my HTC One from second hand several days ago and I instantly noticed that something wasn't right. System was naked, no bloatware, no usual settings, no proper identification so I decided to install custom rom. I tried to boot to bootloader which I wanted to unlock(I guessed it's locked 'cause recovery is stock) with key combos, adb but it simply didn't boot to bootloader nor it rebooted or sometimes it went to factory mode which is on chinese. Again, I tried to find which version of phone I own but I can't figure it out. Moreover, I downloaded and put stock rom on virtual sd card and booted to recovery, opened menu with power button and selected to install package from zip just like it's said in thread but it outputted 'Install /sdcard...' and nothing else for past couple hours. Recovery isn't frozen, It shows\hides menu when power button is pressed. I tried to force shut down it by holding only\in combination with power button\volume buttons but nothing happens. I don't know what else to do...
Any help would be appreciated.
EDIT: It eventually discharged but when I turn it on with charger in it I get blinking white screen on every 3 seconds and when long pressing power button phone just vibrates. In combination with volume down it keeps blinking on every 3 secs and with volume up on every 5 seconds. To me, it looks like it's trying to boot but bootloader can't find anything installed. Computer is recognizing usb device on the moments when I connect it with usb just like when device is rebooting.
Jon2555 said:
I got my HTC One from second hand several days ago and I instantly noticed that something wasn't right. System was naked, no bloatware, no usual settings, no proper identification so I decided to install custom rom. I tried to boot to bootloader which I wanted to unlock(I guessed it's locked 'cause recovery is stock) with key combos, adb but it simply didn't boot to bootloader nor it rebooted or sometimes it went to factory mode which is on chinese. Again, I tried to find which version of phone I own but I can't figure it out. Moreover, I downloaded and put stock rom on virtual sd card and booted to recovery, opened menu with power button and selected to install package from zip just like it's said in thread but it outputted 'Install /sdcard...' and nothing else for past couple hours. Recovery isn't frozen, It shows\hides menu when power button is pressed. I tried to force shut down it by holding only\in combination with power button\volume buttons but nothing happens. I don't know what else to do...
Any help would be appreciated.
Click to expand...
Click to collapse
You have a fake phone
I agree, you've probably got a counterfeit One, but you can't flash custom roms from stock recovery anyway.
Firstly, thank you for any answer. How do you mean 'fake'?! I got it in original box and IMEI's are same(on box and device) What can I do with it then?
I tried to flash stock rom designed for stock recovery, at least that's how I understood.
MIDN07100 (Europe, a guy from which I got device claimed that it's from England so this should fit)
IMEI:354436053103493(same on device and on box, checked with IMEI checker it appears as valid HTC One device)
Hi, I sorry to bother anyone, but I need help because my phone is not responding and I don't know what to do.
C6603, rooted, dual recovery installed, bootloader unlocked (I think)
So here's what happened. I very successfully installed the existenz ultimate rom on my phone. It was a wonderful rom and everything was going well. However, I accidentally dropped my phone and needed to send it for repair. Before sending it to the shop, I decided to do a factory reset using the option in recovery mode.
When I got the phone back from the repair shop, I wanted to install the same rom. What I did was download the rom installer and then install the zip file using the recovery mode. I went through the AROMA installer and everything, So I thought everything was going fine. When the phone rebooted, it showed the SONY logo, followed by a permanent black screen. The screen is on, it is just black.
I scoured the xda forums and I tried several things, to no avail:
I cannot enter recovery mode.
My PC cannot recognize my phone.
Flashtool cannot recognize the phone. My phone can't seem to enter flashmode, either.
I tried holding the power button and the vol. up button, and the phone does indeed restart (no vibrations), showing the SONY logo, and then I'm stuck with the black screen again.
I hope somebody can help me!
EDIT: I managed to somehow get flashmode working, so I think my phone is fine now! What a false alarm! In case this ever happens to anyone, what I did was to unplug the phone from any source of charging, then proceed to hold on the power button and vol. up button for REALLY long, I think almost 20 seconds. This managed to switch my phone off (it would keep restarting if I didn't hold in down long enough).
download stock firmware and open flashtool & ready to flash,dont connect until it say.connect your usb cable to ur phone,then reboot ur phone when display goes to black connect ur phone to pc whith pressing vol down ,then flash tool detect ur phone and it flash,sorry foe my bad english
So I tried to relock my BL and restore it to the stock so I could send my phone to the lab for a broken screen replacement.
I flashed stock OS, it worked great, messed around with locking the BL with the flashtool, and all I left was restoring my DRM keys from the backup I created..
I couldn't make it so I found somewhere that I might need a real super user help and not the kingroot one..
so after alot of fastboot modes I've been entered, I shut down the device one more time to flash the other old ROM for the SU,
and when I tried to enter fastboot by plugging in the cable, I noticed the device won't turn on..
no response, dead, no vol down+ power to force restart, no fastboot, nothing.. the only living signal I get is by plugging power cord and the led is blinking red or blinking to my press on the power button..
Also I read some where about the hidden yellow super reset button.. it managed to do 3 vibrations but thats it.. still bricked..
Is there anything to do?
I didn't ruin anything physical or flashed something wrong it simply died for no reason.. what the hell happened?
So first things first:
I am not a noob, I have been flashing phones for years
The phone has an UNLOCKED bootloader
I know what a bootloader/recovery are etc
So last night I upgraded my phone to 6.0.1. I then decided to root it and get a kernel on for color control. So I download one of the new kernels (Elementalx) for 6.0.1 and the systemless root that he recommended in his post. I flash both files and boot the phone, the phone bootloops twice after the password to boot screen and then it works fine. I install a few things adjust a few things (nothing pertaining to root) and then before I jump into the shower I reboot it. I look at it after a few minutes and it is sitting at the google screen with the padlock, no worries it has happened before so I reboot it only to be met with this same screen. Over and over it just halts here. I do the button trick to get into the bootloader, no dice. No button combination can get me past this screen.
I then go over to my PC and try it out and see if I am getting a Q_BULK issue (I had it happen to my Galaxy Nexus before) and the PC doesn't even acknowledge it, so now I am getting a little worried. I cannot power off the device normally, it just reboots back to here. I can manage a trick with the power cable and some quick button presses to enter the "charging" mode and from there it appears to shut down. Upon boot though it comes right back to this halt. :-/
So, does anyone have ANY experience with this before I contact Motorola? I really don't want to because I have frame swapped and don't look kindly on the process of undoing it for a replacement, but if it must be then it must be. Below is a TLR
Phone boots to Google/padlock screen
CANNOT access the bootloader/recovery through normal means
PC does not recognize it (I did prior in both fastboot and recovery so the drivers are all installed)
the phone does NOT appear to be in Q_BULK
the phone will not shut down, it just boots back to here
It "was" running ElementalX and the systemless root (both are the newest) for 6.0.1
-Current status, sitting on this screen waiting to die... but it has an almost full charge
OK, first off... YOU ARE A NEWBIE.
Turn off the phone and boot to bootloader and use that to load your custom recovery and restore your working backup.
Failing that, fastboot flash the stock image from bootloader mode.
What are you hoping to accomplish by draining your battery completely, this can only make matters worse.
@scryan you are a funny man?
you didnt say anything about trying to get into recovery.. i assume you tried getting unto your recovery?
Hold power button, up and down button all at the same time. If you are on stock recovery wipe user data and cache. See if you can boot into the bootloader afterwards. That's unusual you cannot get into stock or custom (if you have it) recovery.
So you're main problem here is that you can't get into your bootloader or recovery right now? Hmm..... that can't be good. My best guess would be to keep trying to get it into your bootloader, just keep on holding volume down and power for a long time, hopefully if you can get into either bootloader or recovery you can fastboot flash a clean stock image, or restore a nandroid backup (assuming you have one) with TWRP. My best guess though.
Briefly, your device powers on, so there's sign of life. It is either your cable, pc' usb port or the usb socket of the phone is at fault. Did you try with another usb cable at another usb port in the pc ?
Let the phone power down completely. And when it dies, connect it to a charger while briefly holding the vol down button to get into the bootloader. It might take a while since the phone doesn't have any juice but this trick might just work.
If already no warranty, so dissasembly the deive, re-attack your battery