So first things first:
I am not a noob, I have been flashing phones for years
The phone has an UNLOCKED bootloader
I know what a bootloader/recovery are etc
So last night I upgraded my phone to 6.0.1. I then decided to root it and get a kernel on for color control. So I download one of the new kernels (Elementalx) for 6.0.1 and the systemless root that he recommended in his post. I flash both files and boot the phone, the phone bootloops twice after the password to boot screen and then it works fine. I install a few things adjust a few things (nothing pertaining to root) and then before I jump into the shower I reboot it. I look at it after a few minutes and it is sitting at the google screen with the padlock, no worries it has happened before so I reboot it only to be met with this same screen. Over and over it just halts here. I do the button trick to get into the bootloader, no dice. No button combination can get me past this screen.
I then go over to my PC and try it out and see if I am getting a Q_BULK issue (I had it happen to my Galaxy Nexus before) and the PC doesn't even acknowledge it, so now I am getting a little worried. I cannot power off the device normally, it just reboots back to here. I can manage a trick with the power cable and some quick button presses to enter the "charging" mode and from there it appears to shut down. Upon boot though it comes right back to this halt. :-/
So, does anyone have ANY experience with this before I contact Motorola? I really don't want to because I have frame swapped and don't look kindly on the process of undoing it for a replacement, but if it must be then it must be. Below is a TLR
Phone boots to Google/padlock screen
CANNOT access the bootloader/recovery through normal means
PC does not recognize it (I did prior in both fastboot and recovery so the drivers are all installed)
the phone does NOT appear to be in Q_BULK
the phone will not shut down, it just boots back to here
It "was" running ElementalX and the systemless root (both are the newest) for 6.0.1
-Current status, sitting on this screen waiting to die... but it has an almost full charge
OK, first off... YOU ARE A NEWBIE.
Turn off the phone and boot to bootloader and use that to load your custom recovery and restore your working backup.
Failing that, fastboot flash the stock image from bootloader mode.
What are you hoping to accomplish by draining your battery completely, this can only make matters worse.
@scryan you are a funny man?
you didnt say anything about trying to get into recovery.. i assume you tried getting unto your recovery?
Hold power button, up and down button all at the same time. If you are on stock recovery wipe user data and cache. See if you can boot into the bootloader afterwards. That's unusual you cannot get into stock or custom (if you have it) recovery.
So you're main problem here is that you can't get into your bootloader or recovery right now? Hmm..... that can't be good. My best guess would be to keep trying to get it into your bootloader, just keep on holding volume down and power for a long time, hopefully if you can get into either bootloader or recovery you can fastboot flash a clean stock image, or restore a nandroid backup (assuming you have one) with TWRP. My best guess though.
Briefly, your device powers on, so there's sign of life. It is either your cable, pc' usb port or the usb socket of the phone is at fault. Did you try with another usb cable at another usb port in the pc ?
Let the phone power down completely. And when it dies, connect it to a charger while briefly holding the vol down button to get into the bootloader. It might take a while since the phone doesn't have any juice but this trick might just work.
If already no warranty, so dissasembly the deive, re-attack your battery
Related
Hi Everyone;
I unlocked my phone for flashing custom rom. After unlocking i reebooted it and was normal. Then i flashed cwm via htc one toolkit. It was successfull as well. Then i go to cwm and made factory reset + wipe cache + dalvik cache. Then i go to install zip from sd card but i could not find my rom file. Thought, it was deleted while unlocking device. Then decided to reboot phone again to copy rom file into the phone and reboot.
But, when i rebooted phone from cwm, it stuck on HTC Logo( Quietly Brilliant screen). Waited sometime, but nothing happened. Then i tried to power off it and boot into bootloader or recovery. I press and hold power button but it does not respond anyhow. When i am holding power button ,back and home buttons are blinking but nothing happens. Almost five minutes i waited as holding down power button but phone does not power off anyhow. i tried all methods like vol down + power, vol up + power and both volume keys + power. But really nothing happens, just blinking back and home buttons. That's all.
I can not simply power off device. :crying:
I also tried boot device via fastboot commands but it says "waiting for device" means computer does not recognize device.
Guys, i need an urgent help. Please...
just keep trying to reboot via holding power or power+vol down. if it doesnt reboot after 30 sec or so let go then try again. if that doesnt work you will have to wait for the battery to die. once you get to bootloader use all in one toolkit to erace cache. then boot to recovery and you rom should be there if not boot back to bootloader and sideload rom
skinsfanbdh said:
just keep trying to reboot via holding power or power+vol down. if it doesnt reboot after 30 sec or so let go then try again. if that doesnt work you will have to wait for the battery to die. once you get to bootloader use all in one toolkit to erace cache. then boot to recovery and you rom should be there if not boot back to bootloader and sideload rom
Click to expand...
Click to collapse
just keep trying to reboot via holding power or power+vol down. if it doesnt reboot after 30 sec or so let go then try again. if that doesnt work you will have to wait for the battery to die. once you get to bootloader use all in one toolkit to erace cache. then boot to recovery and you rom should be there if not boot back to bootloader and sideload rom
Click to expand...
Click to collapse
First thank you for your quick reply. Unfortunatelly, power+vol down does not work at all. Maybe i tried 50 times.
Anyhow, after battery die. How can i boot into bootloader. I mean, can phone be charged again in this situation? Also, even if i manage to boot into bootloader or recovery how can i put custom rom file into phone. Actually, i did not use sideload or whatever you mentioned before.
I am serouisly confused now and don't know what to do.
Anyhow, as you said, firlst i need wait to battery die i think. Then i will report back whats happen.
Thank you again btw.
Blue_Shine said:
First thank you for your quick reply. Unfortunatelly, power+vol down does not work at all. Maybe i tried 50 times.
Anyhow, after battery die. How can i boot into bootloader. I mean, can phone be charged again in this situation? Also, even if i manage to boot into bootloader or recovery how can i put custom rom file into phone. Actually, i did not use sideload or whatever you mentioned before.
I am serouisly confused now and don't know what to do.
Anyhow, as you said, firlst i need wait to battery die i think. Then i will report back whats happen.
Thank you again btw.
Click to expand...
Click to collapse
yes your not the first person with this problem. hold power+vol down to get into bootloader. press power button in bootloader to get in fast boot mode. use all in one toolkit to erase cache and side load rom. i recommend all in one toolkit because it automates the process. just select the option then follow on screen steps
Good to hear that i am not the first person That means somehow there is a solution i beleive. Still waiting for battery die. even i had 50 percent battery at the begining but still it holds on I never say again htc battery is bad
I exeprienced that stucking on boot logo several times before with my other htc phones but holding power + vol down/up worked always. This is the first time for me that i faced with power button can not power off device.. Well, ,i hope i wish i can handle out this problem. Definetley with your help.
Regards,
I am having the same problem and don't know what to do :crying:
Today I just got my One. Unlocked bootloader, rooted, flashed Android Revolution rom. Everything worked fine for a while... I wanted to reinstall the rom because I wanted to change some options in the installer - I did not wipe because it was the same rom (big mistake I guess!!). After making the installation option changes, when it was done it proceeded to reboot but now I am stuck in a white HTC logo boot loop hell... (with the red text at the bottom that says "this build is for development purposes only" etc). Holy crap I never had a phone that I could not remove the battery. I cannot get this back into recovery or ANYTHING, it just keeps looping... computer recognizes it, no problem with drivers or anything it just doesn't stay connected long enough (because of the constant looping) to be able to use the toolkit.
PLEASE any advice?? Can't even shut it down omg. Do I have a $600 brick here? :crying::crying:
Deeva said:
I am having the same problem and don't know what to do :crying:
Today I just got my One. Unlocked bootloader, rooted, flashed Android Revolution rom. Everything worked fine for a while... I wanted to reinstall the rom because I wanted to change some options in the installer - I did not wipe because it was the same rom (big mistake I guess!!). After making the installation option changes, when it was done it proceeded to reboot but now I am stuck in a white HTC logo boot loop hell... (with the red text at the bottom that says "this build is for development purposes only" etc). Holy crap I never had a phone that I could not remove the battery. I cannot get this back into recovery or ANYTHING, it just keeps looping... computer recognizes it, no problem with drivers or anything it just doesn't stay connected long enough (because of the constant looping) to be able to use the toolkit.
PLEASE any advice?? Can't even shut it down omg. Do I have a $600 brick here? :crying::crying:
Click to expand...
Click to collapse
Did you read the other posts in this thread? The way you do a "battery pull" on this phone is to HOLD the PWR + VOL DOWN button for ~15seconds. Your capactivie buttons will blink, too. On my device, it took exactly 15seconds to reboot. There have been some reports of some phones that get so stuck that you just have to wait until the battery dies and charge it back up.
Alternatively, if the computer is recongizing it, try to adb reboot recovery to try and get into the recovery.
Deeva said:
I am having the same problem and don't know what to do :crying:
Today I just got my One. Unlocked bootloader, rooted, flashed Android Revolution rom. Everything worked fine for a while... I wanted to reinstall the rom because I wanted to change some options in the installer - I did not wipe because it was the same rom (big mistake I guess!!). After making the installation option changes, when it was done it proceeded to reboot but now I am stuck in a white HTC logo boot loop hell... (with the red text at the bottom that says "this build is for development purposes only" etc). Holy crap I never had a phone that I could not remove the battery. I cannot get this back into recovery or ANYTHING, it just keeps looping... computer recognizes it, no problem with drivers or anything it just doesn't stay connected long enough (because of the constant looping) to be able to use the toolkit.
PLEASE any advice?? Can't even shut it down omg. Do I have a $600 brick here? :crying::crying:
Click to expand...
Click to collapse
no. if it turns on you should be ok. try holdind power+vol down to get into bootloader then try toolkit if it just stays on waiting for device press power button to get into fastboot mode from bootloader
skinsfanbdh said:
yes your not the first person with this problem. hold power+vol down to get into bootloader. press power button in bootloader to get in fast boot mode. use all in one toolkit to erase cache and side load rom. i recommend all in one toolkit because it automates the process. just select the option then follow on screen steps
Click to expand...
Click to collapse
hi again. this morning my battery finally out. Then i put my phone to the charger and started it in fastboot mode( that is a good new) Then i left it for 20-30 minutes to charge a little bit for flashing custom rom.Then i went to recovery and started adb sideload. Sideload was succesful and finally came to aroma installer of trickdroid. I chose my installation options and started to flash rom but process was frozen on 10 percent. It was saying unmount system, unmount cahce and both of them has notification as "already unmounted". But installation was not going on. Then again i tried to go back fasboot mode again by press and holding power+vol down but unfortunatelly lights are blinking but nothing happens again. I think i need to wait to battery die again.
Isn't it quite weird? Why power+vol down combination does not work for me anytime? So, do i need to wait for battery die in every frozen? Do you have any ideas or comments ?
Do i need to go back to stock first ?
EDIT : Battery was out again and i tried once more. This time installation (trick droid) was successful but it frozen at the end this time. And unfortunatelly i can not restart (power+vol down) it again again Holy crap, i am really pissed off with this problem.
O..K...Finally, i managed to start my phone and now it works... Especially thank you skinsfanbdh for your support.
But still i don't know how to solve button configuration problem. But anyhow i think i won't need quite sometim to use it I hope someone can find a solution for that later.
Guide me with steps please
Blue_Shine said:
O..K...Finally, i managed to start my phone and now it works... Especially thank you skinsfanbdh for your support.
But still i don't know how to solve button configuration problem. But anyhow i think i won't need quite sometim to use it I hope someone can find a solution for that later.
Click to expand...
Click to collapse
Hi, I have the same problem now and I let my phone die but when I put it to charge and try to go in bootloader, it's doesn't go and gets stuck at the logo again.
Would you please guide me with the steps how u fixed your phone?
Blue_Shine said:
O..K...Finally, i managed to start my phone and now it works... Especially thank you skinsfanbdh for your support.
But still i don't know how to solve button configuration problem. But anyhow i think i won't need quite sometim to use it I hope someone can find a solution for that later.
Click to expand...
Click to collapse
Do u fix it,i have same problem.on Zenfone max.after successfully rom installation i reboot my phone thn it stuck on resurrection remix logo,then i go into recovery,and mount the stock image without wiping.then twrp showed that image installation successful.thn i reboot it in recovery but it stuck on asus logo.what can i do right now?
Fix it
skinsfanbdh said:
no. if it turns on you should be ok. try holdind power+vol down to get into bootloader then try toolkit if it just stays on waiting for device press power button to get into fastboot mode from bootloader
Click to expand...
Click to collapse
Today i fixed it via asus flash tool.with the right steps it can be flash to stock with no problem
What should I do if I can't even get to the boot screen? I tried holding down the power and volume up buttons, but it just restarts and goes back to the same HTC load screen, what do I do????
So the thing is, I decided to buy this phone from another person a few days ago while it was still working but it had this one problem where the owner told me about how the phone can't be shutdown unless the battery runs out of power. Any time you shut it down, it simply reboots instead. I thought it was most likely a problem I could fix after flashing, so I decided to buy it.
Using Flashtool I was able to see that if timed pressing the buttons and plugging it into my computer right before the reboot started, I could boot into flashmode. This phone came in the 4.4 KK firmware and the 10.5.1.A.0.292 Generic NCB build, so I flashed an older kernel and rooted it using Towelroot before reflashing the 10.5.1.A.0.292 Generic NCB kernal. After rooting (and testing if root apps can shut it down which didn't work either), with a locked bootloader I installed the XZDualRecovery using the method here because I was finding it so hard to unlock the bootloader and Flashtool wouldn't do it either. It automatically booted into TWRP recovery menu but when I tried to flash a ROM (existenz Ultimate 3.5 to be precise), it simply made the screen go black for a second and took me back to the recovery menu. So figuring it was a bad download, I downloaded a smaller ROM but when I rebooted I accidentally went into PhilZ Touch menu instead. Deciding to do the usual wipe before flashing, here's where I messed up like an idiot. I saw an option along the lines of "Wipe CLEAN for flashing ROM" or something and trusted it so much despite it saying it's gonna wipe the system partition clean as well (I still don't know why I accepted even when warned of that).
So basically now I have a system that boots the SONY splashscreen and then goes black with the back light still on unless the battery runs out. I can't shut it down no matter how long I hold the power button and if I restart, it boots back to the same thing. I have no recovery menu now thanks to my genius idea of wiping the system, and the only thing I can enter is flashmode. So when I try to flash an FTF firmware (I tried every firmware I could get) back into the phone with Flashtool, it would simply say "preparing for flashing" for about a minute before it says "device disconnected" because the phone decides to exit flash mode and boot normally. I have a locked bootloader (with bootloader unlocking allowed), so I can't flash recovery menus. When I try booting by holding the VolumeUp key and plugging it in, it enters flash mode only with the red LED on and I still get the same results on Flashtool.
Was wondering if there were any ways around this that I might have missed before deciding to open the phone and change the hardware? And if it comes to that, what would I need to change (have always been a software guy when it comes to phones)? Any tips and advice would be appreciated.
TLDR: Have a bricked c6603 from wiping the system, that can't shutdown and keeps rebooting and refuses to be flashed.
If you have time before the phone reboots, hold Volume UP and the power key for 15 seconds. The phone will vibrate once at 10 seconds. Keep holding the keys until you feel 3 vibrations. This will hard power down the phone.
Sent from my C6603
^I've tried this and it simply boots back up again.
Hmm. That should definitely shut the device down, not restart it.
Sounds like there could possibly be an issue with your power button. I've heard of issues with the power button after water damage. Have you checked the water ingress indicators under the flaps? If any are red, it points to earlier damage from water.
Sent from my C6603
kingvortex said:
Hmm. That should definitely shut the device down, not restart it.
Sounds like there could possibly be an issue with your power button. I've heard of issues with the power button after water damage. Have you checked the water ingress indicators under the flaps? If any are red, it points to earlier damage from water.
Sent from my C6603
Click to expand...
Click to collapse
Seems like you're right, I just checked it and it indeed has a faded red color on it. Do you think if I take the phone apart it the power button could be fixed or should I swap something else inside this from another Xperia?
7ty6er said:
^I've tried this and it simply boots back up again.
Click to expand...
Click to collapse
I experienced this problem
Pls hold down volume When u connect your phone to pc via flashtool,
It will connect in flash mode
After that , just flash 0.230 kernel via flash mode ( kernel not rom )
Then disconnect your phone
Turn it off ( hold power button and volume up till it vibrates 3 times )
Then before it turn on again , hold down the volume down and connect it to pc via usb and this time flash 0.283 Rom ( not kernel )
This worked for me
Hey,
I have been reading around, but this is my first thread, and I'm looking for some help.
I got a G920T, and I was trying to get a custom rom installed, got twrp working, but after running xtresolite, twisted and VN-ROM installers (yes, i checked to download the ones for my model) and factory wiping had no luck, phone was just stuck at "powered by samsung" screen. So I decided trying to go back to stock, but ODIN gave me only fails.
Tried: AOCG, COF6 and EPD1 getting failed on writing from ODIN, then I realized i couln't get into twrp anymore, so I tried to get to download mode BUT then I couldn't get to it, just got to the green custom os warning screen and pressing any button doesn't get me anywhere, from there I can only turn phone off.
Tried to emergency recover with Smart Switch, but since it doesn't get to Download mode, it's not recognizing phone, and neither does Odin.
So:
-vol down+home+power=green screen/turn off
-No Download mode
Any ideas? I found another guy somewhere asking for same issue, but he got no answers.
Thanks in advance!!
Power off phone first don't restart and try it
Download mode usually always exists even with software screw ups
Power down first then hold volume down +home button then power button keep holding till screen comes up then chose volume up to continue to download mode .
IT takes like a few seconds to get it to power to download mode sometimes between 2-6seconds in my experience
For Odin try newest version and just reflash the idle kernel 3.0.2.0 twrp for s6 6.0.1
Very important you unchecked auto reboot in Odin before you flash twrp again .
You have to manually reboot after it flashes
Then you should be able to swipe to allow modifications then either restore rom backup or sideload a rom.
You can also recover your phone I'f you mount USB otg in twrp and down load a rom to it on the flash drive just a idea
If you wanna go to stock Download uvu3epd1 from Samsung site
Sent from my SM-G920T using XDA-Developers mobile app
Some advance
Hey,
Thanks a lot for your answer androidddaaron!
It came to the point it went off and it wasn't charging when connected. No powered by samsung message, no download mode, nothing, so, in my desperation i placed the phone over a qi charger i use for my nexus7, after about 30-40 minutes, i grabbed it, it was very hot, and not even powering on (just grey battery not moving), so i decided to go deeper, took advantage of the heat to remove back cover and began to strip it apart.
I bridged the power on/off contacts directly on the board, and what was my surprise, powered by samsung message. So i got to figure out the combination for vol- contact on the board (3 contacts for volume: gnd, vol+ and vol-). Turns out i could get this time through and got to download mode . I'm waiting right now for software download to complete, it will probably take a couple hours, since i'm only getting 1.8Mb/s.
Before starting software download with Smart Switch (Odin not working here), i made tests for buttons, they seem to be closing circuit as expected with tester, BUT, when attached to board, i'm not getting the correct behavior, so i'm thinking i might have a faulty vol- or something, right now, working directly on board (no back cover, no aluminium), no buttons, bridging contacts as needed.
I'll wait for smart switch to finish and hopefully getting phone to work. I'll report after that. :fingers-crossed:
Umm.. I don't know what your saying sounds like you tore apart your phone.
The button combo works as I mentioned how to.
Flash the right twrp.. as mentioned with the procedures .
Then USB otg flash a rom
OR try odin flash stock
Best of luck
Sent from my SM-G920T using XDA-Developers mobile app
The Android logo with an exclamation mark and the word "Error!". All the buttons unresponsive. Froze in recovery mode when selected the "Sideload" option by mistake and did not send anything via ADB.
The handset is on STOCK firmware, NOT rooted and has LOCKED bootloader. Not modded in any way; just connected via ADB.
Buttons not responsive. Pressing and holding the power button has no effect.
Do I have to wait until battery drains?
Funny thing, I have rooted phones for years, flashed ROMs, sideloaded, even created a ROM. Not an expert, just curious - and never came across such a situation with a completely locked phone.
This is my primary phone and is badly needed...
Thanks for any hints.
Never mind, after 30 mins or so, the phone suddenly rebooted to system after plugged in. Weird, but things seem to be back to normal.
So, I recently updated magisk on my phone and as usual to update my phone restarts, but this time it didn't boot up.
I think its in bootloop because when i connect it to my pc with a usb cable it goes on and off also, i cannot access to TWRP.
Can you get to bootloader (fastboot)?
If so you can restore a stock boot image and start over, or try to boot to TWRP with fastboot boot twrp.img and restore the boot image from there and then flash the installer (rename the .apk to .zip as per the new v22+ installation instructions).
I am unable to go into the bootloader or maybe im just doing it the wrong way do you mind guiding me? :/
or maybe i don't have the drivers..
my phone just connects and disconnects, so im not so sure i can go into the bootloader and launch a comand.
Can you shutdown your phone?
i don't think, because it's always turning on and off because the usb sound is going off and on in my pc so i dont really know
You need to use a button combo to get to bootloader or recovery (since you can't boot to Android). A quick web search gives this:
https://droidrecovery.com/doogee-s68-pro-recovery-mode/
thameme said:
i don't think, because it's always turning on and off because the usb sound is going off and on in my pc so i dont really know
Click to expand...
Click to collapse
Exactly like what happen to my device as well
Nope, it does not let me go into the bootloader. Not even with the button combo.
Do you have twrp installed on your phone by any chance? Also a stock boot.img?
First you need to calm down I know how frustrating seeing your device on bootloop and can't even shutdown it ...
i do not have twrp, but i can download a stock boot.img
would you like me to guide you how to fix it i don't have anything to do?
Yes, thank you.
Your device is going on bootloop right now and keep vibrating right?
it's not vibrating. but it probably is in bootloop
lol mine is vibrating while on bootloop okay enough chitchat let's start
vibration is actually good indication for the next process
prepare ADB and USB cable
Now press Power Button and VOL UP at the same time wait for vibration let go Power Button keep holding VOL up for at least 3secs then let go
it's still not vibrating
now press VOL DOWN there's 3 out of 1 chance that you actually made it to fastboot mode ...