upgraded to 5.0 but then decide to see if I could downgrade and I bricked my phone trying to use Odin with the 4.4.2 files. Any suggestions or anyone going thru something similar?
Is it a hard brick? Can you get in recovery or download? What were your steps? With the Note 3 L update, we are able to go back to 4.4.2 and 4.4.4 via ODIN. What did you download. This info will be a big help to see if we can go back to KK from L.
Atomic Virus said:
upgraded to 5.0 but then decide to see if I could downgrade and I bricked my phone trying to use Odin with the 4.4.2 files. Any suggestions or anyone going thru something similar?
Click to expand...
Click to collapse
Try flashing this file in Odin, it does not contain the bootloader so it should flash successfully: G900A_Downgrade_to_NCE
I can get to download menu but after I run Odin 3.09 and use the recovery files AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar SYS REV.
I get the following error:
Check Fail Refer 2 > Binary 1
Secure Check Fail: system
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> system.img.ext4
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
muniz_ri said:
Try flashing this file in Odin, it does not contain the bootloader so it should flash successfully: G900A_Downgrade_to_NCE
Click to expand...
Click to collapse
Let me try it. Will report back.
Atomic Virus said:
Let me try it. Will report back.
Click to expand...
Click to collapse
Still getting same error.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900A_Downgrade_to_NCE.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> persist.img.ext4
<ID:0/006> system.img.ext4
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Atomic Virus said:
Still getting same error.
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900A_Downgrade_to_NCE.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> persist.img.ext4
<ID:0/006> system.img.ext4
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Very sorry to hear that. A BestBuy Samsung Experience or AT&T shop can likely get you back up and running.
muniz_ri said:
Very sorry to hear that. A BestBuy Samsung Experience or AT&T shop can likely get you back up and running.
Click to expand...
Click to collapse
No worries. Might wait it out for a bit maybe someone will come across a similar situation.
muniz_ri said:
Very sorry to hear that. A BestBuy Samsung Experience or AT&T shop can likely get you back up and running.
Click to expand...
Click to collapse
Great news I am back up and running. I went ahead flash the G900A_OC4_Stock_Partitions using Odin's PDA slot (AP in Odin v3.09+) from your other thread.
Atomic Virus said:
Great news I am back up and running. I went ahead flash the G900A_OC4_Stock_Partitions using Odin's PDA slot (AP in Odin v3.09+) from your other thread.
Click to expand...
Click to collapse
OK, I see now how you bricked....the kernel for the NCE .tar you first flashed updated successfully causing the brick because your system at that point was 5.0.
muniz_ri said:
OK, I see now how you bricked....the kernel for the NCE .tar you first flashed updated successfully causing the brick because your system at that point was 5.0.
Click to expand...
Click to collapse
That is correct! Thanks for your help.
Atomic Virus said:
That is correct! Thanks for your help.
Click to expand...
Click to collapse
I did the same thing you did what exactly did you do to get it to boot back up?
Fitz110 said:
I did the same thing you did what exactly did you do to get it to boot back up?
Click to expand...
Click to collapse
I went ahead flash the G900A_OC4_Stock_Partitions using Odin's PDA slot (AP in Odin v3.09+). Which you can get off this thread. http://forum.xda-developers.com/att-...-2015-t3021120 Sorry for the late responds.
Atomic Virus said:
I went ahead flash the G900A_OC4_Stock_Partitions using Odin's PDA slot (AP in Odin v3.09+). Which you can get off this thread. http://forum.xda-developers.com/att-...-2015-t3021120 Sorry for the late responds.
Click to expand...
Click to collapse
Okay thanks and the link is dead do you think share the file with some way?
Fitz110 said:
Okay thanks and the link is dead do you think share the file with some way?
Click to expand...
Click to collapse
Here
http://forum.xda-developers.com/showthread.php?t=3076803
OPOfreak said:
Here
http://forum.xda-developers.com/showthread.php?t=3076803
Click to expand...
Click to collapse
Thanks but i think that's a updated version of the file presented in that post I was trying to get the original file
Fitz110 said:
Okay thanks and the link is dead do you think share the file with some way?
Click to expand...
Click to collapse
As a junior member, and it's not just you but quite a few, you really need to read and do some research on your phone before you turn it into a very expensive paperweight.
The link I provided took about 5 seconds in this very forum.
Plus doing your reading and research before asking will save you a ton of flaming. Just some friendly advice from someone that's been there done that.
Atomic Virus said:
Great news I am back up and running. I went ahead flash the G900A_OC4_Stock_Partitions using Odin's PDA slot (AP in Odin v3.09+) from your other thread.
Click to expand...
Click to collapse
so what was the exact process? do you mind making it clear for other users? thanks.
Fitz110 said:
Thanks but i think that's a updated version of the file presented in that post I was trying to get the original file
Click to expand...
Click to collapse
No it isn't that's where you will get the Stock partitions he was talking about
OPOfreak said:
No it isn't that's where you will get the Stock partitions he was talking about
Click to expand...
Click to collapse
Okay thanks , my apologies.
Related
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> Enter CS for MD5..
<ID:0/006> Check MD5.. Do not unplug the cable..
<ID:0/006> Please wait..
<ID:0/006> Checking MD5 finished Sucessfully..
<ID:0/006> Leave CS..
<ID:0/006> SetupConnection..
how long does it stay like this for?
What will i do if it doesnt do anything ?
ok think ive done it . hopefully it doesnt get stuck at factoryfs.rfs . all i did was go on process kill kiestrayagent. then i did download mode while the phone was off. not turn the phone on then do download mode as i did. just a care for any1 else . thanks
that should fix it.... never use odin if kies is running thats probably what caused your problem
marcon10 said:
ok think ive done it . hopefully it doesnt get stuck at factoryfs.rfs . all i did was go on process kill kiestrayagent. then i did download mode while the phone was off. not turn the phone on then do download mode as i did. just a care for any1 else . thanks
Click to expand...
Click to collapse
My last odin flash failed on the factory.rfs don't know why ive flashed the phone many times before with odin never had any problems. So i Removed the battery and re flashed with re-partition 512.pit. Working again
Well that was my first flash to darkys 9.2 resurrection and went well. Just learning to configure battery. Just reading on darkys 9.3 .
Sent from my GT-I9000 using XDA App
Hi,
Im stuck at SetupConnection....
smartin said:
Hi,
Im stuck at SetupConnection....
Click to expand...
Click to collapse
Did you close all Kies processes in task manager? If not do so and you should be able to flash now
Odin Problems or im doing Crap? Please Help
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
hi guys,
my phone doen't work anymore..
when i press the power button nothing happens.
when i try to get into odin mode nothing happens.
when i plug in usb cable nothing happens.
its totally dead.
anyone idea what i can do?
or shall i send it to samsung?
thanks
lol4it said:
hi guys,
my phone doen't work anymore..
when i press the power button nothing happens.
when i try to get into odin mode nothing happens.
when i plug in usb cable nothing happens.
its totally dead.
anyone idea what i can do?
or shall i send it to samsung?
thanks
Click to expand...
Click to collapse
What exactly did you do to arrive at that point?
Sent from my GT-N7000 using Tapatalk 2
tried to flash using odin 1.85
ehmmm maybe try to charge battery. And sometimes phone works but screen isnt, try to go in download mode and to check is it connecting to odin even if screen is black ;D gl
batterie is charged.
already tried everything i know
i dont think so that after flashing with 1.85 odin you would get hard brick, i think that you messed up with files in not right sections and baam- brick :/
yes youre right
i just plugged into my pc and windows is searching for samsung mobile usb composite device drivers..
and now finaly odin found it too
i think i just paniced too hard...
where can i get a original firmware?
lol4it said:
yes youre right
i just plugged into my pc and windows is searching for samsung mobile usb composite device drivers..
and now finaly odin found it too
i think i just paniced too hard...
where can i get a original firmware?
Click to expand...
Click to collapse
www.sammobile.com all official firmwares ;D
ok gonna try:
GT-N7000 N7000XXLPY 4.0.3 2012 May N7000OXALPY Open Germany Download Unlock
(got vodafone germany)
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLPY_N7000OXALPY_N7000XXLPT_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
lol4it said:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLPY_N7000OXALPY_N7000XXLPT_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
you extracted zip file? you need to put .tar file at PDA ^^
ok
now my pc find my phone as unknown device -.-
and odin nothign..
ok worked now:
Code:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.img
<ID:0/003> NAND Write Start!!
<ID:0/003> zImage
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
but when i press power button still black screen??
EDIT: do i have to change standard settings like re-partition or flash lock?
lol4it said:
ok worked now:
Code:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.img
<ID:0/003> NAND Write Start!!
<ID:0/003> zImage
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
but when i press power button still black screen??
EDIT: do i have to change standard settings like re-partition or flash lock?
Click to expand...
Click to collapse
i didnt change settings like re-partition and etc. You fcked up something, a lot of people flashed without problems
yes i know =(
but i dont think my screen is broken..
wtf is this?? someone must help me
i got sound and everthing but dat screen is BLACK
Sorry mate phone had dont suppose u would sell as need screen for mine as drop it
Sent from my GT-N7000 using xda premium
Tried to flash aokp jb 4.1.2 milestone1 rom on my galaxy note ics 4.0.4.Launched cwm recovery mode and wiped data,which went off fine but when I flashed the aokp milestone 1 rom the whole thing stuck for few minutes and suddenly the screen went blank.I waited long hoping it would restart... but it didnt.Opened the battery,reinstall it and tried to switch on but failed..I also tried to launch the Cwm recovery ,also tried the download mode but the phone refused to start.... please help....
dead battery?
nokiamodeln91 said:
dead battery?
Click to expand...
Click to collapse
No... I charged the phone before proceeding....it was around 90-95% when I started....!!!
Hi everyone,
I bought a new samsung s6 and rooted it using pingpong, now i must unroot it so i can install the new update, well i downloaded the firmware stock odin 3.10, but everytime i try unrooting it usin odin i have this message
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My samsung is a G920F
firmware i trying to use is G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5
im so desesperate i tried so many time but no changing at all can someone help Me please
Thanks
Must use Odin v3.10.6
Neostatic17 said:
Hi everyone,
I bought a new samsung s6 and rooted it using pingpong, now i must unroot it so i can install the new update, well i downloaded the firmware stock odin 3.10, but everytime i try unrooting it usin odin i have this message
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My samsung is a G920F
firmware i trying to use is G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5
im so desesperate i tried so many time but no changing at all can someone help Me please
Thanks
Click to expand...
Click to collapse
wp4jot said:
Must use Odin v3.10.6
Click to expand...
Click to collapse
Hi wp4jot,
i have used odin 3.10.6 but it still don't work do you have an idea why its not working , or how can i solve this problem
Thanks
I don't. Did you flash all 4 files at once?
Neostatic17 said:
Hi wp4jot,
i have used odin 3.10.6 but it still don't work do you have an idea why its not working , or how can i solve this problem
Thanks
Click to expand...
Click to collapse
I had this problem.. You must have v3.10.6 and flash every file in the corresponding place, after that I still got a fail message but I tried un-checking the auto reboot option and that did the trick (this will make the phone stay in download mode even after you complete the flash, to quit download mode you must press the volume down button and the power button at the same time for about 10 seconds) hope that helps, let me know.
vontokkerths said:
I had this problem.. You must have v3.10.6 and flash every file in the corresponding place, after that I still got a fail message but I tried un-checking the auto reboot option and that did the trick (this will make the phone stay in download mode even after you complete the flash, to quit download mode you must press the volume down button and the power button at the same time for about 10 seconds) hope that helps, let me know.
Click to expand...
Click to collapse
I Have the same problem with S6- SMG20T (Dutch) Now trying to un-check the auto reboot otion. Hope it works for me.
didn't worked for me
wp4jot said:
I don't. Did you flash all 4 files at once?
Click to expand...
Click to collapse
What do you mean with that? witch 4 files?
Hope you can help me.
After a factory swipe and installing vodafone wallet on my S6 it says that it doesn't work on a rooted Phone
You have to put each file in the corresponding place, when you download the stock rom after you've extracted the zip you're supposed to have a file called AP, BL, CSC, AND the other which I cannot remember, those are the files you're supposed to flash, if you try to flash just AP like on the screenshot it's not going to work.
Neostatic17 said:
Hi everyone,
I bought a new samsung s6 and rooted it using pingpong, now i must unroot it so i can install the new update, well i downloaded the firmware stock odin 3.10, but everytime i try unrooting it usin odin i have this message
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My samsung is a G920F
firmware i trying to use is G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5
im so desesperate i tried so many time but no changing at all can someone help Me please
Thanks
Click to expand...
Click to collapse
I think you downloaded the wrong firmware for your phone, your phone is G920F and the firmware you are trying to flash is G925F.
@Neostatic17, it looks like you downloaded the wrong file. The file should be a tar.zip, not tar.md5. Once you download the correct tar.zip, extract the file and you will see 4 files within the one file you downloaded. Then flash all 4 files with odin.
Edit...Ok, I've checked my pc and the file is a tar.zip before you extract it and once it's extracted, there are 4 tar.md5 files. All you have to do is put the AP file in the AP slot, BL file in the BL slot and so on. I leave auto reboot checked, but that is up to you.
I have the SM-G920T S6 and I recently tried to install twrp and root using this guide: http://forum.xda-developers.com/tmo...l/how-to-flash-marshmallow-update-sm-t3362983. I have always used a nexus device so I am not familiar with odin, but I thought I had it figured out. In odin it says the recovery flash was successful and gave me a PASS message. Once I tried rebooting to recovery it was still the stock recovery and no twrp. I have gone back over the instructions, but I still get the same results. I have checked and my system is now marked as custom but Knox is not tripped. Any help would be appreciated.
You are really close. I had similar trouble flashing twrp o. My G920T. I got it to work flash with Odin using twrp by idlekernel. Here is the link download the version to flash with odin under AP or PDA.
I hope this helps.
RedZaton said:
You are really close. I had similar trouble flashing twrp o. My G920T. I got it to work flash with Odin using twrp by idlekernel. Here is the link download the version to flash with odin under AP or PDA.
I hope this helps.
Click to expand...
Click to collapse
Thank you. Which of those md5 files should I download?
I installed "twrp-3.0.2-2-zeroflte.tar.md5" via Odin.
RedZaton said:
I installed "twrp-3.0.2-2-zeroflte.tar.md5" via Odin.
Click to expand...
Click to collapse
I tried it again and it still does not do anything. I unchecked auto reboot and noticed that it still had the download bar up like it did not finish but even after 15 min the bar stayed.
Odin says this when I flash the image:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
trixter29 said:
I tried it again and it still does not do anything. I unchecked auto reboot and noticed that it still had the download bar up like it did not finish but even after 15 min the bar stayed.
Odin says this when I flash the image:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1100)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Make sure auto reboot is unchecked in Odin, flash Twrp and boot directly into it after flash. It should work just fine with MM.
This is what I get. Please help!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920VVRS3BPI1_N920VVZW3BPI1_N920VVRS3BPI1_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> modem.bin
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
mithon said:
This is what I get. Please help
Click to expand...
Click to collapse
Well I am not an expert but it looks like it failed on the modem.
It looks like you are flashing Verizon firmware.
Is your device a Verizon device?
Do you know that the firmware is for your device?
CodeNameRedNeck said:
Well I am not an expert but it looks like it failed on the modem.
It looks like you are flashing Verizon firmware.
Is your device a Verizon device?
Do you know that the firmware is for your device?
Click to expand...
Click to collapse
no dear, i am flash verizon many firmware still modem fail.
6
mithon said:
no dear, i am flash verizon many firmware still modem fail.
Click to expand...
Click to collapse
I am not clear on your answers.
Do you have a Verizon device?
Is the firmware made for your device?
CodeNameRedNeck said:
I am not clear on your answers.
Do you have a Verizon device?
Is the firmware made for your device?
Click to expand...
Click to collapse
yes i have have a Verizon device.
i dont know what firmware in device.......
mithon said:
This is what I get. Please help!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N920VVRS3BPI1_N920VVZW3BPI1_N920VVRS3BPI1_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> modem.bin
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
what happen after this process...is ur phone boot to boot logo or not
if yes press vol up+power+home key...u will see the stock recovery ...wipe data/factory reset...reboot...see ur phone boot...
if not reply back
rohitsinghpu said:
what happen after this process...is ur phone boot to boot logo or not
if yes press vol up+power+home key...u will see the stock recovery ...wipe data/factory reset...reboot...see ur phone boot...
if not reply back
Click to expand...
Click to collapse
not boot logo.....
mithon said:
not boot logo.....
Click to expand...
Click to collapse
use smart switch application on pc...connect the phone ...download the latest firmware of ur phone