Since i've update my SGS to android froyo the Proximity sensor stoped working and the position sensor taken 30sec to turn the image...
I've used the test mode code to check hardware error, but there everything is working perfectly...
If I put the Android 2.1 the problem doesn't show up.
Does anyone have the same problem or solution?
Nobody has this issue?
Is quite strange... because if i put a Android 2.1 ROM everything works just fine, but with later version of android the sensors still working (using test mode from SGS Tools, I confirmed that the sensors are just fine), but the system takes a huge time (~30sec) to do something...
Please, if anyone knows anything that could solve this problem, please say something!
I think that in the first week that I had Froyo everything warked fine, but I'm not sure...
Is there any way to do a complete reset and set everything to default values including Hardware settings?
I've already done Factory reset and Full factory reset, by CWM and Code.
Nobody??? Anything???
Is this a genuine samsung rom you are using .
A flashed rom or a genuine Kies updated firmware .
jje
I'm now using a ROM official (sam***gfirmwares.co*) flashed by ODIN.
Should I try use Kies?
No i was just trying to rule out a flakey rom .
My usual suggestion is a wipe via ODIN
http://forum.xda-developers.com/showthread.php?t=882014
But i would stop at Eclair and see if its solved the problem if OK upgrade further .
jje
Its the same thing...
Its quite awkward, because only apendds in Froyo...
why not try a custom froyo rom, head over to doc's kitchen and cook yourself one up. also try lagfix, and any other speed up tweaks. how does the phone respond normally ?? without the sensors ? is it quite speedy or does it lag ??
The phone work just fine but when i turn the phone it take a lot of time to twist the image... I can even still interact with the screen until it turns...
The proximity sensor takes a lot of time too...
No one else has this problem?
Hi,
Can anyone help me out, i recently installed the new cm7 RC1 for INCs...yesterday i disable the flash function in the camera...and now when i switch it on it doesnt come on at all!
I have used a torch app to see that the back led is still functional, but no camera apps seem to be able to enable it.
how anyone else had the same problem and fixed it?
--want to delete this thread!!-- please ignore and mods could you delete please
Hi there,
the proximity sensor on my i9000 isn´t working anymore. Everytime I place a call/get called the screen turns black and freezes. I have to pull the battery and restart it.
Testing the sensor on the LCD-test the screen turned green and the i9000 startet vibrating. Here, too only pulling the battery made it stop.
Here is what I tried so far:
- flashing different stock fw (Android 2.2 / 2.3.x)
- applied handicapped settings
- Using Proximity_Screen_Off App and Sanity-App on stock fw
- blowing air into the USB jack/vacuuming the jack
- opened the device to mechanically clean the sensor
All of the above failed!
The only way I can get it to work is when running android 2.3.7 Joker´s MiUi and run the Proximity_Screen_Off App.
Are there any other suggestions as to what can be tried?
Else I will have to get a new motherboard, because wouldn´t want to be restricted to using only one particular rom.
Any input is greatly appreciated
Thanks Christine
if i recall good (but kill me ive drinked some atm) the greensih issue was showing with voodoo color kernels and all the sensor peoblems came with badly assembled kernel.
so i would advice you to reflash pure 3 file firmware (repartition pit and all that jazz)
and if your sensors still would not work just reflash to your carrier or stock formware for your region and push it to repair center with proper dwscription (do no mentions miui or other crap)
Thanks for answering!
I flashed 3-part firmware, pretty much everything available and a CF-Root kernel.
So it couldn´t have been a bad kernel.
Can´t take it back to service, no warranty left.
I just flashed 2.3.5 and CF-Root and now I am fooling around with it some more.
I just think it´s weird that it would work with that and only that MiUi.
impossible unless youve got some other galaxy variaant than i9000
Title says all, i have already re-flashed and checked the md5 to make sure it wasn't a bad flash...
I wish i would have backed up my original BL ever since i flashed the OA1 BL i have had screen flickering issues and have to push my power button 5 to 12 times in a row to tun the screen ON from waking up..
The screen will flicker really bad when i set it to low dim but bump it up and it works fine.. When i'm actually using the phone it works flawless no screen issues but run into trouble every single times when i try to turn the screen ON from a wake.
That's why i believe it's not a hardware issue. it's something in the firmware not working correctly in my revision model of the g900a.
Can i please get some new boot loaders to try out that someone might have???
I will try anything at this point i really need some help!
Bootloader Version:
G900AUCU2AOA1
Specs: G900A / Kit Kat 4.4.2 Stock
Thank you a lot,
-JBriZzeL
Hi! After reflashing a stock version of android 9 (02u uk if it matters) because i wanted to get back to stock from the hades rom my touchscreen started having deadzones or phantom touches .One in the middle of the screen and one in the bottom .How can i fix this? Has anyone else encountered this before?
Try wiping the Cache Partition. If that doesn't work then you need to recalibrate the touchscreen on your device.