Related
I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John
I should say that I had flashed using button's ROM RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
and this worked fine!
I then copied across my T-mobile Extended ROM and again everything seemed OK.
BUT then I tried to restore my new saved OS ROM using aWizard and this caused a freeze on my Wizard. It was after a hard reset that the wizard stopped at the splash screen.
Now of course I'm limited in my options because Activesync won't work until the Wizard has fully booted up.
I have tried setting the Wizard into bootloader mode and tried several ROM's (RUU Installer ones) but every time the correct splash screen comes up with the new ROM numbers but that is as far as it gets.
I also noticed on hard reset that you get the following message
Format FAT partition
Format failed
it then goes to the splash screen as before.
Are there any other things I can try Or will I have to send it back to T-mobile for a replacement??
(It's only 2 months old and I have re-flashed it with the orginal T-mobile ROM - but still won't go past the splash screen!!)
I live in hope
John
I have this EXACT same problem!
I can reflash any ROM but it will not go past the splash screen. Only difference was I wasn't playing with my extended ROM. I flashed the AKU2 QTEK ROM yesterday and have been fine through several soft resets, etc. This last time I was uninstalling phonealarm and after a soft reset I got a "could not find smswakeup.exe" (or something similar) and it's been stuck ever since! I also get the "Format Failed" message. Can anyone help!?
I think I'm going to have to send it back to T-mobile and hope they give me a replacement. Something is wrong, it doesn't seem to make any difference what ROM I used.
I think I'll reload the T-mobile shipped ROM grom the FTP site and send it back - and claim ignorance that it it suddenlt freezed and now won't boot up! - Bummer!!!
Right I've logged a fault and it will be sent back - let's hope T-mobile can't detect it's been unlocked and had several ROM updates - I suspect they will try a ROM update themselves then give up ???
The worrying thing though is that it IS possible to kill your phone with updates - maybe it was when I used aWizard to try and restore a ROM that did it??? I'll be more carefull next time!!
this has just happened to one of the devices im flashing at the moment.... absolulty f**king raging :evil: :evil:
i wish teher was a solution!!? anyone got any ideas?
activesync wont find it, so aWizard wont work.
i can flash between 3 roms without any problems (1.5.x 1.6.x 2.x) but always hangs on the splash screen. i have flashed back to the default rom that it came installed with it so i could just send it back to o2 (only 2 days old!)
i would rather just get it sorted by myself thoough so if anyone has ANY ideas then please let me know.
thank you!
Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:
tonym001 said:
Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:
Click to expand...
Click to collapse
yup looks like i might have to give up... ohwell, no worries i will just return it back to O2...
looks like one of our sales guys wont be getting a new phone on tuesday :lol:
same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
There is hope
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.
THIS is truly heaven for me !!
I have my O2 XDA MINI S locked on the splash screen .. and i updated some ROMS to it ....BUT IT DOESNT GET THROUGH IT .... please tell me what to do in a little detailed manner .. please so that i can get my phone to work.. there is no warranty on the phone and i stay IN INDIA . SO YOU'LL ARE MY ONLY HOPE .
my email id is - [email protected]
If you have a dump of the O2 XDA MINI S ..please mail it to me
Plese tell me what to do next ? WILL TRULY APPRECIATE HELP
PLEASE SOME ONE ATLEAST MAIL ME the dump of the os SO THAT I CAN TRY THE SD CARD UPGRADING ,.,,, O2 XDA MINI S
Re: There is hope
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
hellomoto_25 said:
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.
Click to expand...
Click to collapse
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
odyseus said:
I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John
Click to expand...
Click to collapse
stuck on o2 screen helppp
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.I see alot of post, so complicated
Thank you so much
my mail : [email protected]
Thanks friend
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse
how to use bootloader
could you tell me how to use mentioned bootloader for restoring the images? where can I get the software?
Please help
Hendrick
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse
Hi Arnold
My O2 cda mini s get stuck at splash scree, I read your post, still not so understand how to solve it, could you be so kind to write me step by step, and send me some software to solve it. Your help will be so much appreciated.
Hendrick
Email: [email protected]
arnoldl said:
same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold
Click to expand...
Click to collapse
Hi everyone! I am badly need help to fix my MDA. My MDA stuck when it boot up to T-mobile white screen. I tried to do hard reset by pressing and holding Conn Manager and Voiddial buttons while pressing reset then press Send. I got and message
Format FAT Partition
Format is Failed
Now I am still able to flsh with any ROM but I just doing the same thing, stuck on boot screen. Is it the end of my MDA? Please hel
Is it realy no one can help?
I don't believe that no one can help me even a command.
If I have the whole white screen, the device was like in bootloader. Flash can start and than wil all OK..
I think You wrote wrong Start Adress in Your own ROM
If I have the whole white screen, the device was like in bootloader. Flash can start and than wil all OK..
I think You wrote wrong Start Adress in Your own ROM
I don't get it
Johnnnnnnnnnny said:
If I have the whole white screen, the device was like in bootloader. Flash can start and than wil all OK..
I think You wrote wrong Start Adress in Your own ROM
Click to expand...
Click to collapse
What should I do? any rom for me to flash to solve this problem?
You could flash any originaly ROM with write IPL/SPL
and quicky. If the battery will turn off. the Wizard will bricked
I flash with right rom
Johnnnnnnnnnny said:
You could flash any originaly ROM with write IPL/SPL
and quicky. If the battery will turn off. the Wizard will bricked
Click to expand...
Click to collapse
I flashed with T-mobile ROM 2.26. It went thru 100% but when the device reboot, It just stuck on the T-mobile boot screen wich saying
IPL: 2.26
SPL: 2.26
GSM: 02.25.11
OS: 2.26.10.2
Finally
Finally I got my MDA fix.
Re: Finally
KhMeRA said:
Finally I got my MDA fix.
Click to expand...
Click to collapse
Please tell everyone what you did to fix your problem.
Molski
he was in bootloader.. He hasn´t brick her phone by wrong xG IPL/SPL
Re: Finally
molski said:
KhMeRA said:
Finally I got my MDA fix.
Click to expand...
Click to collapse
Please tell everyone what you did to fix your problem.
Molski
Click to expand...
Click to collapse
Just follow this link http://forum.xda-developers.com/viewtopic.php?t=62268&start=0&postdays=0&postorder=asc&highlight
please tell us whate happend (fixed or no )
sifreen said:
please tell us whate happend (fixed or no )
Click to expand...
Click to collapse
Read post #8 on the 1st page.
Hi all, tried to upload my Wizard (8125) G4 to WM6 blackDiamont but it got stuck for more than 50 minutes with shellTool....
Now the phone is stuck on the screen that shows IPL/SPL, GSM and OS. From there i can force it to a hard reset but nothing happens..
Is there a way to get it working again or it just died?
marcelo1251 said:
Hi all, tried to upload my Wizard (8125) G4 to WM6 blackDiamont but it got stuck for more than 50 minutes with shellTool....
Now the phone is stuck on the screen that shows IPL/SPL, GSM and OS. From there i can force it to a hard reset but nothing happens..
Is there a way to get it working again or it just died?
Click to expand...
Click to collapse
Turn the device on and Flash the original ROM or Wizard Love Rom.
Wizard Love can be found here http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
Yeah, thanks man!
well, now trying to load Cingular's 2.25.11.1 WWE the update process got stuck in 95% and shows
error [326]: Invalid Command
This NBF file cannot be used for your PDA phone....
Is there possible that perhaps using Wizard love rom i'd have luck ?
marcelo1251 said:
Yeah, thanks man!
well, now trying to load Cingular's 2.25.11.1 WWE the update process got stuck in 95% and shows
error [326]: Invalid Command
This NBF file cannot be used for your PDA phone....
Is there possible that perhaps using Wizard love rom i'd have luck ?
Click to expand...
Click to collapse
You should be successful with Wizard Love. Good Luck!
I'd bought my htc p3600 pro (black, free from sim-lock & free from any carrier) from London.
As advised by TRINITYGUIDES.INFO site I tried to do HardSPL with all the three available HardSPL files, but of no avail.
When the HardSPL's progress bar comes(on pc) it gives a message on my phone " Enterbootloader.exe....This may harm your device...Do you want to continue.." I pressed yes & the process stopped & gave an error on pc "Error 246 Device not responding" & on phone screen showed the bootloader with
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
I did soft reset on my p3600 & its working as usual with it original spl infos.
I want to put official WM6 SEA version(ROM+RADIO) on my phone...Please help.
I too have the same message when I try to upgrade to hard spl as per teh guide here: http://trinityguides.info/index.php...ask=view&id=25&Itemid=66&limit=1&limitstart=2
Can anyone help? I have tried updating active synch... could there be anything else?
I have flashed my rom befroe to unlock the GPS but I now want to upgrade to WM6.
I guess the hard spl is a failsafe and I can skip this step?
Thanks
wingnutLP said:
I too have the same message when I try to upgrade to hard spl as per teh guide here: http://trinityguides.info/index.php...ask=view&id=25&Itemid=66&limit=1&limitstart=2
Can anyone help? I have tried updating active synch... could there be anything else?
I have flashed my rom befroe to unlock the GPS but I now want to upgrade to WM6.
I guess the hard spl is a failsafe and I can skip this step?
Thanks
Click to expand...
Click to collapse
Search is great function
http://trinityguides.info/index.php?option=com_content&task=view&id=37&Itemid=67
wingnutLP said:
Sorry!
I am an idiot.
Thanks
Click to expand...
Click to collapse
sorry I tried a Google search on the error message and came up with this thread!
wingnutLP said:
sorry I tried a Google search on the error message and came up with this thread!
Click to expand...
Click to collapse
Search more...
With this link:
http://www.google.com/advanced_search?q=+site:http://forum.xda-developers.com&hl=en&lr=&as_qdr=all
if you search error 246 you will get the solution on 11th answer.
Search more...
Have the same [Error 246]! How can I definitly fix it?
Hi,
first of all, sorry for my poor English. I try to explain my problem so good I can... I hope you can help me.
I have the "[Error 246] Device not responding" problem.
I have used a lot the "search"-function and I have found a lot of posts which propose the same solution "restart the Rom upgrade another time". Ok I did it and my PDA works very well, but now I would like to solve the problem radicaly... How can I solve this problem? Should I use SPLexploit (I have found the guide on trinityguides.info) and then reflash a Hard-Spl?
Thx a lot
ciao
Tompo
Some specifications....
Sorry.... I have a P3600 White with Olipro 1.20 and rom Elias 1.9 SE Lite...
Tompo81 said:
Hi,
first of all, sorry for my poor English. I try to explain my problem so good I can... I hope you can help me.
I have the "[Error 246] Device not responding" problem.
I have used a lot the "search"-function and I have found a lot of posts which propose the same solution "restart the Rom upgrade another time". Ok I did it and my PDA works very well, but now I would like to solve the problem radicaly... How can I solve this problem? Should I use SPLexploit (I have found the guide on trinityguides.info) and then reflash a Hard-Spl?
Thx a lot
ciao
Tompo
Click to expand...
Click to collapse
Before flash manually enter bootloader. After start the rom update utility. (As www.trinityguides.info suggest). You will not get error 246 any more
thanks for answer
Many thanks for anwser...but...
Is this the only solution? If is so, then everbody has this problem, isn't so?
Ciao
Tompo
Tompo81 said:
Many thanks for anwser...but...
Is this the only solution? If is so, then everbody has this problem, isn't so?
Ciao
Tompo
Click to expand...
Click to collapse
www.trinityguide.info
Here is written to flash rom you should manually enter to bootoader. In this case, you will not have error 246.
Most of the people know this, so they have not this problem
Those who not manually enter bootloader can get error 246, and this way of flashing is not as safe as the manual bootloader way.
(because in this case you use the spl uploaded by RUU, not the hard-spl on the PDA)
Ok, now I really understand
Ok, this is a very good anwser, short and clear... thanks...
Ciao
Tompo
fktsndr said:
www.trinityguide.info
Here is written to flash rom you should manually enter to bootoader. In this case, you will not have error 246.
Most of the people know this, so they have not this problem
Those who not manually enter bootloader can get error 246, and this way of flashing is not as safe as the manual bootloader way.
(because in this case you use the spl uploaded by RUU, not the hard-spl on the PDA)
Click to expand...
Click to collapse
When i connect my touch hd to pc in active sync mode, then shutdown device an run in bootloader (volume down and power button at same time) i get the tricolor screen and after a while i get the progress bar on my phone and on pc. But i stays on 0% and says 'update error' after a while.
please help
I Have the Same Problem the Status bar Freeze On 0% and nothing happened
Until the Update Error Message Displayed
Please Advice
Thank You
Note: I Have HTC Diamond2 (Topaz) Without Sim Louk
Hi Me has the trinity 3600 as a VPA GPS vodafone branding, and i get the same error message trying to run the bootloader and entering tricolor screen, ---> error 246 aber manually starting into bootlaoder and restatrting the romupdateutil.exe same error 260 no connention...
So you guys have a working version of the updating ?
And please remove all the links which are not working, linking a solve for the 246 problem, there are nomore links available...
thanks
Dome
I found a way to solve the problem 246 go in you mobile device, -->start -> settings-> connections ->USB to PC open this. Remove the hook @ Advanced networksettings activation! ---> click OK--> close
try again the bootloader etc, then on the tricolore reboot screen is shown USB in the lower white field and the bootloader can do its routine complete.
Have Fun with flashing the phones!
Testet with original German Vodafone available ROM " vpa_comp_gps_RUU_Trinity_VF_DE_1_23_162_4_6275_1_29_00_01_13000_108_Ship.exe "
testet with ZackMcRofls superfast german rom " RUU_Trinity_GER_1.23.162.2_GPS_v3f_by_ZakMcRofl "
testet with
" htcp3600_RUU_Trinity_HTC_GER_1-23-407-2_103_6275_1-38-00-11_108 "
First was Zack´s rom, 2nd. was Original Rom, 3. was Trinitys rom, after trxing all, i flashed Zacks Rom again, it was the best in my view.
Thank you verymuch, bb
Hey guys i tried to update my rom and while the update stops in 99% and said updtae ultiality Error.
now my Telefone doesn't start and stay in the 3 Colors Screen.
please Help
Hey,
i´ve the same Problem.
I wanted to flash my MDA Vario, but it stops at 99%.
Now, I can´t start the phone and I can´t connect it to ActiveSync.
So I can´t flash it again.
When I want to flash an older ROM, there came a fail.
Sorry for my bad english I´m from Germany... I tried my best ;-)
FloStilo said:
Hey,
i´ve the same Problem.
I wanted to flash my MDA Vario, but it stops at 99%.
Now, I can´t start the phone and I can´t connect it to ActiveSync.
So I can´t flash it again.
When I want to flash an older ROM, there came a fail.
Sorry for my bad english I´m from Germany... I tried my best ;-)
Click to expand...
Click to collapse
Always post the vital data of the phone,which is your device,G3 or G4,post the present IPL/SPL...? of the phone.Which rom you were trying to flash ?Does your phone get into bootloaders (tricolor screen) ?
It won't activesync in bootloaders or in the absence of a working rom (OS),but its possible to flash a rom in bootloaders.Download the official rom from the carrier's site and flash in the bootloaders to recover back to its default status.
Cheers!