Related
When i use WLAN the 3G/GSM connection is lost after a few minutes and i have to reboot the phone to get it back. Does anybody know why this might be? Could it be the Radio?
I think its turning it off because your connecting to the internet through the wifi, when you disable wifi it should re-enable the 3g connection, but if it doesnt you can turn on the data connection...
thats what it sounds like is going on from your post. When I turn on wifi it will drop the data connection but has always reconnected to it once I disable wifi or I go outside of my wifi's range and something try's to connect to the net...
Yes, it is logical, you could not have opened two types of connection concurrently. One type closed another one.
ive had the same problem, when i connect to wi-fi i lose the data connection and it doesnt let me browse until i turn wi-fi off...i dont understand the point of wi-fi if u cant browse with the speed since the data connection is lost?
Thanks men! By turning on the data connection after i used wifi it reconnected!
timace said:
ive had the same problem, when i connect to wi-fi i lose the data connection and it doesnt let me browse until i turn wi-fi off...i dont understand the point of wi-fi if u cant browse with the speed since the data connection is lost?
Click to expand...
Click to collapse
What Wifi allows you to do us connect wirelessly to another connection, at home its my DSL, which is much faster than the edge network, and if I did not have an unlimited data plan wouldnt add to my phone bill. In that way its very usefull. Seeing how its faster and available at home or in places where your cell signal might not be strong or available you can use it to get online.
But you need to tell it your no longer using wifi for it to reconnect through the network to deliver data to you again.
10332007 said:
What Wifi allows you to do us connect wirelessly to another connection, at home its my DSL, which is much faster than the edge network, and if I did not have an unlimited data plan wouldnt add to my phone bill. In that way its very usefull. Seeing how its faster and available at home or in places where your cell signal might not be strong or available you can use it to get online.
But you need to tell it your no longer using wifi for it to reconnect through the network to deliver data to you again.
Click to expand...
Click to collapse
ok so when it comes to wi-fi im a big newbie, i have a tmo wing and have flashed (upgraded) rom...i also have dsl at home how is it i can connect and access this...when i search for wi-fi it usually only picks up my neighbors connections never my own...?
If you have a wifi router or your modem has a build in wifi option you go into your modem to set it up. Most modems / routers come with it broadcasting the SSID so you should see something (usually the default is the name of the manufacturer)
If you have your paperwork you can open your web browser and type in the address to open the internal OS and make changes as you see fit. For example mine is a linksys and its default address was http://192.168.1.1, most routers used to default to that but since a lot of modems are coming out with build in os and firewalls they have that IP so routers can be changed like mine. Once in the OS you can set up your pw so no one else can play with your settings
Navigate to the Wireless section and there should be a bunch of settings. I renamed my WiFi name to match my home network, and disabled the SSID broadcast. Then changed the chanel for some of my other devices, if you dont have anything that requires this leave it alone. Then enable WEP or other protection, 128 bit wep is pretty decent and anyone hacking through it will probably be disappointed with your lack of juicy goods.
Once you have the SSID and the Key encription you go to your phone and mirror the information into the WiFi settings. The web will be a 26 or so string of letters / numbers that will equal the password you set. These must be typed in perfectly or it will not work, took me 6 or so tries to get it typed in correctly but once its in you wont need to do it again unless you reset the phone or change the network settings.
If all that goes through open IE on the phone and hit up google or something, if it loads your online.
Thats a jumbled and messy tutorial, I can fix it to be more user friendly if you need me to do it, but with you not seeing any SSID but your neighbors your wifi is either non existant or disabled...
10332007 said:
If you have a wifi router or your modem has a build in wifi option you go into your modem to set it up. Most modems / routers come with it broadcasting the SSID so you should see something (usually the default is the name of the manufacturer)
If you have your paperwork you can open your web browser and type in the address to open the internal OS and make changes as you see fit. For example mine is a linksys and its default address was http://192.168.1.1, most routers used to default to that but since a lot of modems are coming out with build in os and firewalls they have that IP so routers can be changed like mine. Once in the OS you can set up your pw so no one else can play with your settings
Navigate to the Wireless section and there should be a bunch of settings. I renamed my WiFi name to match my home network, and disabled the SSID broadcast. Then changed the chanel for some of my other devices, if you dont have anything that requires this leave it alone. Then enable WEP or other protection, 128 bit wep is pretty decent and anyone hacking through it will probably be disappointed with your lack of juicy goods.
Once you have the SSID and the Key encription you go to your phone and mirror the information into the WiFi settings. The web will be a 26 or so string of letters / numbers that will equal the password you set. These must be typed in perfectly or it will not work, took me 6 or so tries to get it typed in correctly but once its in you wont need to do it again unless you reset the phone or change the network settings.
If all that goes through open IE on the phone and hit up google or something, if it loads your online.
Thats a jumbled and messy tutorial, I can fix it to be more user friendly if you need me to do it, but with you not seeing any SSID but your neighbors your wifi is either non existant or disabled...
Click to expand...
Click to collapse
thanks for the quick reply, ill give it a try...might need the more user friendly version lol sorry
Its no problem, the biggest thing will be weather or not you have a wifi router or modem. Then depending on the brand the IP you have to type in to log into the modem. Each router / modem will have paperwork with it that tells you how to do it, some are different but thankfully most are the same.
The un is usually blank and the pw is usually admin, sometimes now they dont even put one unless you specify it. Once your in the OS its pretty self explanitory, there are lots of things to not mess with, but in the wifi area you can look over my post and figure most of it out,
if you get hung up on somethin just post what it is and ill see what I can do
Hello to all diamond people,
We all know, there is huge issue with this great phone about Wi-Fi connections. While Wi-Fi is one of the reasons people choosed touch diamond, what is their disapointment when they find out wi-fi doesn't work as it should.
I am talking about problem I am experiencing by myself - I am unable to connect to my home WPA secured and encrypted network. If I turn the security off on my router and wireless network becomes open, there is no problem at all.
But who wants unsecured, open wireless network at home, so all the neighbours can download whatever they want through your network?
Nobody.
During my research throughout forums I have come accross many people, experiencing same problem, but was not able to find the solution to the problem, or what is causing it.
My aim is to gather as many information as possible to help to fix this problem, so everyone could use wi-fi on their own home WPA secured wireless network.
Any ideas?
What is your ROM and radio versions? I've no problem connecting to my WPA enabled network. Which WPA option did you choose? It must match the same WPA option on your router. There are WPA, WPA-PSK, WPA2, and WPA2-PSK, then there are also TKIP and AES to choose from. Try setting both Diamond and router to use WPA-PSK (TKIP) first, this should have the highest compatibility with other WPA supported devices on your network. And make sure you use a strong passphrase, you can use a WPA key generator.
Hey,
both router and HTC are set to WPA -PSK under TKIP encryption. I use my own network key.
The thing is, in wireless lan manager i can see htc does connect, but only for about a second, then it starts reconnecting all over again.
Sometimes it does connect and works for few minutes and sometimes it does connect to router, but not to the internet. It drives me absolutely mad.
I tried Advanced Config -> Network -> WPA authentication - enabled/disabled, but still experiencing problems.
I have heard there used to be issues with ROMs provided by the network operators, but that is not my case.
ROM: DIB Diamond v 1.33
RADIO: 1.00.25.05
WPA secured
Hey,
If You want to use WPA secured wireless networks with Diamond go to Settings-Wireless LAN-Power Mode and there set Power Save Mode to Best Performance. It works
Sorry for my English...
6sauer said:
Hey,
both router and HTC are set to WPA -PSK under TKIP encryption. I use my own network key.
The thing is, in wireless lan manager i can see htc does connect, but only for about a second, then it starts reconnecting all over again.
Sometimes it does connect and works for few minutes and sometimes it does connect to router, but not to the internet. It drives me absolutely mad.
I tried Advanced Config -> Network -> WPA authentication - enabled/disabled, but still experiencing problems.
I have heard there used to be issues with ROMs provided by the network operators, but that is not my case.
ROM: DIB Diamond v 1.33
RADIO: 1.00.25.05
Click to expand...
Click to collapse
I guess it's probably not your ROM, since the DIB Diamond v1.33 is based on the newer 2.03 ROM. I was wondering, do other devices on your network have the same issue or it's only the Diamond? Connection dropping can be many reasons, and one of them is the router itself.
Reddish said:
Hey,
If You want to use WPA secured wireless networks with Diamond go to Settings-Wireless LAN-Power Mode and there set Power Save Mode to Best Performance. It works
Sorry for my English...
Click to expand...
Click to collapse
I don't have any problem even in Power Save mode.
Somewhere I have come accross the information some routers (particullary Belkins) do have problem with windows mobile devices.
Today I wrote to Belkin Support, thay should reply in 72 hours mad, however we may know more.
Since I am using unsecured wireless network now, at least I have activated the MAC addresses lock - only allowed MAC addresses can connect to router now. What do you think, how secure is that? There is no encryption now, could someone see the sommunication between me and the router?
Which Belkin router are you using? Check if there is a firmware update, you may want to try that.
MAC address filtering should be ok for now, it can stop the majority of people who try to use your network, it will take someone with a bit more networking knowledge to gain access to your network, but most people don't have that knowledge.
Yes, people can capture any unencrypted packets and read them. But if you're connecting to a secure website through HTTPS or any other secure protocols, the packets are still unreadable. For example, in the browser, if it's written https instead of http on the address bar, those sites are secure. Most regular websites are not secure though.
I was having a similar problem on my Touch Pro a while back. My router is also set to WPA-PSK/TKIP. Although you said you tried it, the solution for me was indeed to go into Advanced Config > Network > WPA Authentication > Disabled. I then removed all previous wifi settings and then added them again, and it connected without a problem.
It could be that there's something else preventing your connection, but from what I can tell you should at least have that setting disabled.
6sauer said:
Somewhere I have come accross the information some routers (particullary Belkins) do have problem with windows mobile devices.
Today I wrote to Belkin Support, thay should reply in 72 hours mad, however we may know more.
Since I am using unsecured wireless network now, at least I have activated the MAC addresses lock - only allowed MAC addresses can connect to router now. What do you think, how secure is that? There is no encryption now, could someone see the sommunication between me and the router?
Click to expand...
Click to collapse
its pretty secure, as you cant guess the password, you would have to get in and add your device to the list (which you would need the username and password for)
Hi,
I have an interesting problem. I am in Dubai, where the ISP (Etisalat) provides Internet via Fiber-optic cables to my residence. They have this modem which I connect my wi-fi router to.
After connecting to my wi-fi router the usual way, I have to dial-in via a Broadband PPPoE connection, where I provide the ISP username and password. I have to do this every time I connect to the Internet.
Unfortunately, this means I cannot connect my Nexus One to the Internet This is because I am not aware of any app/functionality that enables PPPoE dialing on Android.
I had installed Connectify for Windows 7 that enabled me to share my authenticated Internet connection with other devices (and hence my N1). However, after FR83, this seems to have stopped working as well, for some reason. It is extremely difficult to connect to the shared Wifi created by Connectify, and even after connecting, I cannot browse the Internet.
I have already tried setting a static IP address for the N1, but this did not resolve the issue.
Can anybody offer guidance, ideas? Any help would be much appreciated!
Cheers,
PI
Get a router, set the router to connect through PPPoE and every device that connects to the wireless router will work.
Thanks, but I wouldn't want to spend more money...
lorin.bute said:
Get a router, set the router to connect through PPPoE and every device that connects to the wireless router will work.
Click to expand...
Click to collapse
Thanks, but I wouldn't want to spend more money on another router. I have a Wi-fi router already, but I don't know if it has the ability to connect via PPPoE. It's a 3COM 3CRWDR200A-75.
Will try and research if I can enable PPPoE via this somehow.
Cheers,
PI
Protocol Set: Dynamic and static IP addressing, DHCP Server, NAT/PAT (with TCP and UDP), PPTP/PPPoE, CHAP, IPCP, SNTP.
http://www.3com.com/products/en_US/detail.jsp?tab=prodspec&sku=3CRWDR200A-75&pathtype=purchase
There you go.
Set your current router to connect through pppoe and you are ready.
Good luck.
droid does
https://market.android.com/details?id=com.cnddu.wifipppoe&feature=search_result
I believe ur wifi "router" is only a wifi access point...
just download wifi pppoe
elgarteo95 said:
I believe ur wifi "router" is only a wifi access point...
Click to expand...
Click to collapse
More accurately, it is a router that happens to have a wireless interface. Most home wireless routers usually have the functionality of a switch as well (that is, providing multiple connections to the same local network), but they usually include routing capability to move traffic from your local area network to the Internet.
Hi guys. I have not access to market because of my region. Can any body get me the WIFI PPPoE ?
wifi pppoe doesnt work for me
hello guys.
My HD7 cannot connect to wifi router. After putting in the password, it keeps trying to connect and after one min throws an error that sorry couldnot connect to the wifi connection. I am using a simple wifi router and not any N router
Authentication type is WPEA2
Thanks in advance
I found this article ( i am not allowed to post link) which says something about a bug in HD7 and venue pro which doesnot allow them to connect to wifi. Any workaround guys
Wifi problem...
Hi,
What is your network SSID name?
I had the wifi problem with my HD7 while my network SSID name had mixed capital and lowercase characters like "GedikNet"
Try to change your network SSID name to all capital or all lowercase characters. (like "gediknet").
Good luck.
Bye.
ssid is SHARAD. still unable to connect
can't have hidden ssid
Hi, if your network is hidden, unhide it. The darn thing cannot connect to a hidden network. I know it is extreamly annoying but that is what Bill-ware gave us.
Hopefully, they will fix it in the update.
Initial connection to my home Wifi was unsuccessful. I had to restart the router and all went fine. Setup: WPA2/AES, b/g/n mixed and SSID is not hidden. It is a Linksys/Cisco device. Check your MAC filter if it blocks your device. DHCP server has to be turned on.
Regards,
Cina.
i did not have an issue with the wifi router... all i had to do is get my mac id as i filter my pc, notebook and pda by mac id..
i heard the ssid must be visible it cant connect to those hidden ones...
maybe lowering the security level will help as well..
HAVE YOU resolve the problem? i can not connect my home wifi as well.
thanks
Seen an app in the HTC hub called hidden wifi but not sure if it helps
Sent from my HD2 using XDA App
Does the N1 have 5GHz wifi like the Samsung?
My home LAN is 5GHz only, so I don't disturb the neighbors with my video streaming.
No, 2.4 only...
Ugh.
OK so I turned on the router's 2.4GHz, but with broadcast SSID off. My N1 wouldn't even try to connect. So I turned on router SSID and it connects AES.
I do -not- want SSID broadcast on, as Windows machines' lazy active scan will find me. Sure they'll never get in, but I do not want broadcast on.
Has anyone succeeded in connecting with it off?
When I am connected wifi and open a website on the phone, does it go over wifi preferred over 3G?
I want to share the SD card with a machine on the LAN. What's the best way to do this? FTP? Reverse SSH tunnel? Is there a sshfs for Android? EDIT: NM on this one.
Yes, I remember connecting to a WiFi with SSID off, when I had Nexus.
It is pointless to keep SSID Broadcasting off. It is super easy to find your SSID anyway, and it causes all sorts of additional problems (like the one you are seeing above). Just keep the network secure and it makes life a lot easier.
http://www.howtogeek.com/howto/2865...hiding-your-wireless-ssid-really-more-secure/
http://blogs.technet.com/b/steriley/archive/2007/10/16/myth-vs-reality-wireless-ssids.aspx
Ok, but sure passive scanners like Kismet will still see me, however 90% of scans are done with an active scanner like Winduhs. Of course I'm using WPA2-AES, but I want to take every measure possible.
Now I find that whenever I have the phone connected to wifi, I lose -all- internet access. Just times out. 3G is still on and wifi is showing connected, but I can't get to websites. As soon as I turn off Wifi I can access the internet again through 3G.
With wifi I -can- access the wireless router's setup webpage from my phone, which tells me I am working through wifi, and I can remotely mount the phone filesystem on a LAN machine using sshfs, but I can not reach anything outside. Any idea why?
Does anyone know whether, when it's working right, it uses the wifi connection in preference over 3G?
The WiFi is ALWAYS preferred to 3G, which means - when you're connected to WiFi, all the internet traffic is routed through WiFi.
I don't understand then, why all data traffic stops to the outside when wifi is connected. The rest of my LAN gets outside fine, just not the phone.
If you can see LAN computers and exchange data with them - it's not the phone that's making problems. See if you have any restrictions in your router.
Oh FFS, my fault...
I set my IP statically for my LAN, and through some alert troubleshooting I found I can ping IPs outside but not DNs. I'd mis-set the DNS server in wifi settings. Now it works great!
I can now use sshdroid to mount my phone's filesystem on my LAN securely. Now, if I could only get it to wifi associate with beacon off...
It would also be nice to mount a filesystem on my LAN to the phone, although I consider the phone unsecure and question the wisdom of that, even with DroidWall running.
There is a market app that lets you connect to a hidden ssid
Sent from my Nexus One using Tapatalk
Cool, but Market is FCing on me. I did a complete reinstall of the newest MIUI.us, and now Market's FCing again. So can't install any Market apps.
As someone else said, turning SSID off is pointless. It's like taking the numbers off the outside of your house and thinking people driving by won't see your house sitting there.
Apparently you didn't understand what I said here:
Quantumstate said:
Ok, but sure passive scanners like Kismet will still see me, however 90% of scans are done with an active scanner like Winduhs. Of course I'm using WPA2-AES, but I want to take every measure possible.
Click to expand...
Click to collapse
If nothing else, please just respect my decision in this regard, or give valid proof that active scanners are not the preponderance.