Database Develop

3g issue with Cricket flashed droid

I am having an annoying issue with my Cricket flashed Moto Droid that hopefully someone here can help me with. Phone works perfectly everywhere 3g etc except when I get within one mile of my house it drops to a 1x data connection. Sometimes turning airplane mode on and off will restore the 3g data most of the time it is no help. When it does work at my house it has full bars of signal. When it drops to 1x I notice I only have two bars of signal. I have tried different roms prls etc and all produce the same result. This only happens at my house and I just don't get it. As soon as I drive a mile away bam 3g is up. And other times 3g works perfect at my house. Any input would be much appreciated.
Sent from my Droid using XDA App

Also I live in a major metropolitan area and my friends Cricket Zio android phone always has a perfect 3g data connection at my house.
Sent from my Droid using XDA App

[Q] 4g data problems at home

It seems I have very good 4g signal at my work but when I am at home, it gets stuck on either 1x or 3g, according to sprint, there is 4g coverage on my house.Does anyone have problems with 4g not working properly? Its getting me annoyed since I use hotspot at my house. Any suggestions would be helpful.

I've noticed it'll show 3 bars of 4g at home, but if I actually start browsing it drops to 3g. My friend had done nothing but complain about sprints network so I am just assuming it's their problem.
Sent from my HTCONE using xda app-developers app

I'm having the same problem! My friends iPhone gets better reception, and we both have Sprint. He gets LTE at my house in my office, but I get 3G or 1X. It's very frustrating. I may return the phone, or leave Sprint altogether, as I didn't have these problems with my Verizon Note 2.

vampire5003 said:
I'm having the same problem! My friends iPhone gets better reception, and we both have Sprint. He gets LTE at my house in my office, but I get 3G or 1X. It's very frustrating. I may return the phone, or leave Sprint altogether, as I didn't have these problems with my Verizon Note 2.
Click to expand...
Click to collapse
I have used sprint chat with an agent and followed every troubleshooting method and still 3g. I will check the store to see if I can exchange it for another phone or see whqt happens

Could just be a week signal. Note that the signal bars on your phone are NOT for 4G. Check out this helpful write up over at S4GRU could help you determine what is up once you check LTE signal levels.

[Q] Force phone to stick to low signal LTE rather than switching to 3g?

Hey guys
So I looked around the forum for an answer to this question and i found similar topics but not exactly what I was looking for. I have the HTC one with sprint and the only issue I have with it is how it handles its preferred networks. If have 2 bars of LTE but 4-5 bars of 3g its going to stay on 3g and not switch to LTE. Is there anyway to change how it gives each signal preference. Currently it will wait till there is no 3g signal before it switches to 2g but LTE is not giving the same preference. I know it's just this phone because I had the iphone 5 before this and when I was on campus at my university it would stick to the 1 bar of LTE i had rather than switching to 3g. If I force the phone in LTE only mode then it will pick the LTE signal but then I can't call and text obviously so it's not very useful.
There are two things that the iphone 5 did which I miss but otherwise love this phone. One is getting LTE in places that has low coverage and the other is roaming on verizon network on 3g. The iphone would always roam on 3g but the htc one only roams on 2g.
Is there a way to change those things with this phone? Thanks in advance!

onelight17 said:
Hey guys
So I looked around the forum for an answer to this question and i found similar topics but not exactly what I was looking for. I have the HTC one with sprint and the only issue I have with it is how it handles its preferred networks. If have 2 bars of LTE but 4-5 bars of 3g its going to stay on 3g and not switch to LTE. Is there anyway to change how it gives each signal preference. Currently it will wait till there is no 3g signal before it switches to 2g but LTE is not giving the same preference. I know it's just this phone because I had the iphone 5 before this and when I was on campus at my university it would stick to the 1 bar of LTE i had rather than switching to 3g. If I force the phone in LTE only mode then it will pick the LTE signal but then I can't call and text obviously so it's not very useful.
There are two things that the iphone 5 did which I miss but otherwise love this phone. One is getting LTE in places that has low coverage and the other is roaming on verizon network on 3g. The iphone would always roam on 3g but the htc one only roams on 2g.
Is there a way to change those things with this phone? Thanks in advance!
Click to expand...
Click to collapse
Have you tried changing the preferred in the *#*#4636*#*# > Phone Information?

Hi thanks for the response. Yes I have messed around with that. That's how I got the LTE only option. It isn't a matter of not finding LTE signal. It's just the way the phone handles what is perferred. The phone first sees if there is a strong LTE signal and it catches that but the moment it goes to about 3 bars or less it will switch to 3g. I want it to continue sticking with LTE until the signal is gone completely like it does with 3g -> 2g.

onelight17 said:
Hi thanks for the response. Yes I have messed around with that. That's how I got the LTE only option. It isn't a matter of not finding LTE signal. It's just the way the phone handles what is perferred. The phone first sees if there is a strong LTE signal and it catches that but the moment it goes to about 3 bars or less it will switch to 3g. I want it to continue sticking with LTE until the signal is gone completely like it does with 3g -> 2g.
Click to expand...
Click to collapse
If its that way then I belive a builder will be able to forge a flashable zip for that purpose.

Terramoto said:
If its that way then I belive a builder will be able to forge a flashable zip for that purpose.
Click to expand...
Click to collapse
I see. And who do I ask for that? Or how can I build one? Sorry I am a bit of a rookie in this. I don't want to mess around with it too much but can learn. I thought there might already be some sort of hack or a modded PRL.

any new insight on this by anyone? thanks
I have lte at my work if I do lte only but it will switch to 3g when i turn everything else one because 3g signal is stronger than lte. id rather use lte however but still have my texting and calling capabilities.

onelight17 said:
any new insight on this by anyone? thanks
I have lte at my work if I do lte only but it will switch to 3g when i turn everything else one because 3g signal is stronger than lte. id rather use lte however but still have my texting and calling capabilities.
Click to expand...
Click to collapse
I know it's not an optimal solution, but have you considered using Google Voice integration in the meantime? With LTE only mode, so long as you're signed into an app of choice (Google Voice/Hangouts should be able to handle your calls and texts if you tweak at it a bit), you should have the desired service until you can get some dev help.

[Q] 4G or LTE with Straight Talk AT&T?

After weeks of playing around with build.props, APNs, and patches, on custom ROMs and stock, I am still attempting to get faster and more consistent data.
4G and LTE are supposed to be possible, but I can't figure it out.
I can get around 5 Mbps down using WCDMA only, but the very next moment in the same spot could be something entirely different.
My mobile data goes out quite often where it is just the outline of a triangle. I have never seen any other letters besides an E and a H.
I am currently on stable CM 10.2.1 installed on a newly created and wiped SS Slot 1, and have been for about a week and a half.
I used default network = 0 in build.prop this time around.
I finally managed to get my phone to recognize my SIM card while using the following configuration:
default network in Phone Testing = LTE/GSM/CDMA auto (PRL) and
preferred network mode in Mobile Network Settings = Global (CDMA/EVDO/LTE/GSM/WCDMA).
It acted really strange at first but the settings stayed even after a handful of reboots.
I am using Straight Talk's current APN settings (tfdata).
My dBm is constantly going from about -90 something to -108 and my asu ranges from around 3 to 14.
Before I just now rebooted, and every so often, it shows 2147483647 dBm and 255 asu; I have only just noticed this in the past few days, however. It is now back to -101 dBm and 6 asu after restarting.
I have attached screenshots of it doing that and a shot of "normalcy", as well as my last few speed tests.
Can anyone tell me what I might be doing wrong?
Should I try default network = 10 again in build.prop?
Or could anyone provide a copy of a build.prop working on all possible network modes (with the ability to edit APNs)?
Thanks in advance. I will take any and all advice or opinions.
I am so over trying to figure this out! When I really need my mobile data, it doesn't work!

I have attached a couple of graphs of my signal highs/lows etc. These results are from the Real Signal app.
I don't really know what they mean, but I am hoping they might shed some light on my issue and I'll get an answer from someone.
Sent from my XT875 using xda app-developers app

How are you getting it to get edge data? On mine I either have HSPA or nothing. Is there a way to make it default automatically to edge when the HSPA signal gets weak. I tried using liquid smooth 4.2.2 and changed it to 2g only and never could get signal. Change it to auto and get HSPA again
Sent from my Nexus S using xda app-developers app

should i take the bionic out office space style?
twfs said:
How are you getting it to get edge data? On mine I either have HSPA or nothing. Is there a way to make it default automatically to edge when the HSPA signal gets weak. I tried using liquid smooth 4.2.2 and changed it to 2g only and never could get signal. Change it to auto and get HSPA again
Click to expand...
Click to collapse
Not really sure how, and when it is on Edge, data hardly works anyway, so I probably can't help you there.
But I do have default network = 10. Only other thing I changed was telephony.lteOnCdmaDevice=0 to get the APN menu under mobile networks.
However, at the moment (and the majority of moments), with Wi-fi off, I have no data, -109 dBm, 5 asu, GPRS service is disconnected, and my phone number is "unknown", so I am definitely not in the position for giving suggestions.
Am going to try CM 11 again today, but I was hoping for some answers before doing anything other than installing..
I will ask more specific questions in the hopes that someone, anyone, can provide some sort of idea for at least 1 of them..
Is it even possible for the Bionic to have consistent, non-frustrating access to 2G, 3G, 4G, and LTE when unlocked for the AT&T or T-Mobile networks using Straight Talk?
Is there a way to enable the APN menu without changing the build.prop?
Does anyone have a targa build.prop (entire thing or line changes) of phone that has reliable data, etc. working on 2G, 3G, 4G, and LTE?
Could it be an issue with the SIM card itself?
Am I even approaching this from the right angle?
Should I just give up and get a new phone?
Thanks in advance.

Patch Idea
I am a novice at best and that may be a stretch.
BUT. Both of my Bionics are running on Straight Talk AT&T 4G sim cards.
One is a hardware REV-B the other is hardware REV-C.
The REV-C is rooted and running on the Jelly Bean stock rom.
The REV-B is rooted and running on a MoKee MK4.4 KitKat Release that I downloaded
from their site and opened in "Safestrap".
I do not think that I have achieved 4G yet however,
I do have fairly stable signal and data since
I installed a CDMA to GSM patch that I found searching these forums.
It includes Straight Talk and AT&T APN!
I am not aloud to post links yet. But if you search for these things here you will probably find them fairly quickly.
I would love to know if you can achieve 4G!
Good Luck!
Netzerite

3g not working if radios set to 3g only?

I noticed if I go to the mobile networking settings and have it it on lte/3g if I leave a 4g area, 3g works ok. If I put the toggle specifically on 3g it shows I have 3g, but anytime I tried to search google or access a data connection the signal goes away and gives me the signal with an exclamation point. I tried finding info on this, but didn't see anything when I searched. Anyone else have this issue? I am on Sprint with the 64gb white device. Thanks

I leave mine on 3g due to the lame multiple text issue. It has no problem staying on 3g. Perhaps try updating your PRL/profile and see if that helps.

I don't have 3g either if I set it to 3g only. I don't leave lte service too often to test whether 3g works when it switches on its own. I may have to make a trip to the mountains to test it. I do know that my old Note 2 would loose lte after flashing tons over and over and I would have to flash back to 100% stock the factory reset from the settings app to fix it. I may try this with my Nexus, about time for a wipe anyway.

Factory reset does not fix it. Just noticed that I don't even get 3g when it is set on LTE. I'm gonna go talk to my cellular provider about it.

I don't know why it wouldn't work. You did update profile and PRL also right? Here's some shots of mine and it's working fine.

I have a bad Sim.....I also don't have a phone number as well..... I swiped with an old card I had and my number appeared, I guess I'll be visiting the store tomorrow to get a new one. Maybe it'll fix my 3g. Its also not wanting to let me pick 3g as an option now, just stays on LTE.

KB112 - Are you on sprint also? I updated prl/profile and no luck still. 3g still works if I am on lte and go into a 3g zone, but if I toggle it to 3g only I get no data. Wondering if its a sprint thing or a lollipop bug on Sprint, or a bad sim, missing feature activation.
Bluemgt06 - did a new sim fix it for you?

Sorry, didn't see this earlier. But yes, I am on Sprint. My 3G would work fine if I set to 3G only. Not sure why yours has issues with this?

Oddly I tried it today and it started working. I think it could have been some kind of issue with the tower/upgrades or a bug that a reset may fix on occasion perhaps.