Related
Hello,
I unlocked my bootloader,
installed twrp (this version ->),
tried to install CM13, but failed because of failed to mount /data
fixed that by formatting data
tried again to install CM13 but it still didn't work, because failed to mount /system
i gave up and did a restart just to realise that there is no system anymore i was stuck in a bootloop,
i decided to go back to Stock and used fastboot to install stock recovery for MM using SRK Tool,
choose to relock my bootloader and after the process it said "the device will now restart to perform a factory reset"
since then i'm stuck at the Huawei Logo (i think my device is stuck because it tries to enter the rom to perform the factory reset but there is nothing it can enter so it's stuck),
i tried to enter fastboot mode but it didn't work,
i can't even turn off my phone because every time i hold the Powerkey the phone just restarts
right now i'm downloading the ROM dload file and hope this will help me.
do you have any ideas/thoughts about this, do i have any chance to save my device ?
EVA-L09
was running emui 5 (B361 i think?)
Dload didn't work nothing happend.... is there anyway huawei will repair this ? if yes how much will it cost ? is there a chance they will repair it (warranty) even tho it was my fault, if i don't tell them what i did and play dumb?
If you power off the phone, and then press and hold the Volume Down key, THEN plug in the USB cable (attached to a PC), does this enter Fastboot mode? (white screen with Android logo)
ConfusedTA said:
If you power off the phone, and then press and hold the Volume Down key, THEN plug in the USB cable (attached to a PC), does this enter Fastboot mode? (white screen with Android logo)
Click to expand...
Click to collapse
No that doesn't work,
i now leave it on to run out of battery and then i try it again.
Yes - let it go completely flat.
Then, press and hold the Volume Down key, and plug the USB cable in. Once you're at this stage, you can use DC-Phoenix to update the firmware. Once this is successfully done, you then power the phone off, press and hold both volume buttons, and re-connect the USB. This puts it into Upgrade mode, and you can use DC-Phoenix again in Upgrade Mode to write the same firmware to it. Once you have done this, you should hopefully have restored your phone.
You may need to go back to an earlier firmware, such as B136, then go through the upgrade path again, if it does not work with B361.
thanks i will try this
it worked ! i unlocked the bootloader again and i tried to install different version of the Stock ROM (b182,b300,b361) i was able to flash b182 and B361 without errors by flashing system,recovery and boot.img but my phone always boots into erecovery and i have no clue why ?
I was in a similar position - until I did the steps I noted with DC-Phoenix.
You don't need to mess around with unlocking the bootloader by using DC-Phoenix.
what is so special about DC-Phoenix and why does this cost 15 Euros for 72 Hours ???
i had the same situation sir
i don't know what to do now
there is no huawei service center in our country
i cant use dc phoenix because i cant pay the 15 euros via paypal
there is a login form before u can use the dc unlocker
please any one help me on this
pls give me account in dc phoenix
i will give the money back via remittance
because i dont have a bank
vinfrix said:
i had the same situation sir
i don't know what to do now
there is no huawei service center in our country
i cant use dc phoenix because i cant pay the 15 euros via paypal
there is a login form before u can use the dc unlocker
please any one help me on this
pls give me account in dc phoenix
i will give the money back via remittance
because i dont have a bank
Click to expand...
Click to collapse
What is your problem?
Rafa Mistry said:
What is your problem?
Click to expand...
Click to collapse
EVA-L09C432B180
LG-U+ SOUTH KOREA
hello guys
i have a serious problem here
this is what happen to my P9 when i try to unlock/root/install twrp
first i used SRK long chod v2.0 tool
the first step i do is unlock the bootloader and yes i can say it works
i unlock the FRP and Bootloader
then i proceed to the next target. installing the twrp recovery
i try so the twrp version inside the SRK tool
but doesnt work then i look some version from
official twrp website , same again does not work either
so i skip that part , and stop going further in order to
back my phone to unvoid the warranty
there is an option in SRK tool which you can relock your bootloader again
so i did relock my bootloader and after rebooting the system
boot stuck appears
no fastboot/no recovery/no system
even the key combination does not
work like forced update via sdcard/dload/update.app
i have no idea what to do now
but i read the thread from SCRAFI
that he used the DC Phoenix and
resurrect his bricked P9
i want to try that solution but i have a problem on that
i cant buy credits for 15 euros i dont have
any e-payment online like paypal bankcards/debit
because before you can use the dc phoenix tool
you are required to login your reserve account
for able to use it. and that is why im so hopeless that
i can ressurect my phone again
please help
please give me some account login for dc phoenix
and promise to bring back the 15 euros via
remittance or any available bank payments..
please. any one who has a big hand
please help me
sorry for wrong english grammar
vinfrix said:
EVA-L09C432B180
LG-U+ SOUTH KOREA
hello guys
i have a serious problem here
this is what happen to my P9 when i try to unlock/root/install twrp
first i used SRK long chod v2.0 tool
the first step i do is unlock the bootloader and yes i can say it works
i unlock the FRP and Bootloader
then i proceed to the next target. installing the twrp recovery
i try so the twrp version inside the SRK tool
but doesnt work then i look some version from
official twrp website , same again does not work either
so i skip that part , and stop going further in order to
back my phone to unvoid the warranty
there is an option in SRK tool which you can relock your bootloader again
so i did relock my bootloader and after rebooting the system
boot stuck appears
no fastboot/no recovery/no system
even the key combination does not
work like forced update via sdcard/dload/update.app
i have no idea what to do now
but i read the thread from SCRAFI
that he used the DC Phoenix and
resurrect his bricked P9
i want to try that solution but i have a problem on that
i cant buy credits for 15 euros i dont have
any e-payment online like paypal bankcards/debit
because before you can use the dc phoenix tool
you are required to login your reserve account
for able to use it. and that is why im so hopeless that
i can ressurect my phone again
please help
please give me some account login for dc phoenix
and promise to bring back the 15 euros via
remittance or any available bank payments..
please. any one who has a big hand
please help me
sorry for wrong english grammar
https://www.youtube.com/watch?v=https://youtu.be/2HrllM9iLzs
Click to expand...
Click to collapse
Your System is nougat & srk 2.0 have twrp for Marshmallow. Just turn of your phone & HOlD Volume Down button & connect usb to your pc than sent your phone screen picture
Rafa Mistry said:
Your System is nougat & srk 2.0 have twrp for Marshmallow. Just turn of your phone & HOlD Volume Down button & connect usb to your pc than sent your phone screen picture
Click to expand...
Click to collapse
in this stage my phone is marshmallow sir
i think im not i nougat version
android 6.0
i will try sir
vinfrix said:
in this stage my phone is marshmallow sir
i think im not i nougat version
android 6.0
i will try sir
Click to expand...
Click to collapse
Turn of your phone & HOlD Volume Down button & connect to your pc
Rafa Mistry said:
Turn of your phone & HOlD Volume Down button & connect to your pc
Click to expand...
Click to collapse
not working sir
phone is only in charge mode
not booting up
when i try to boot
it stuck in huawei boot logo
and start to vibrate twice
vinfrix said:
not working sir
phone is only in charge mode
not booting up
when i try to boot
it stuck in huawei boot logo
and start to vibrate twice
Click to expand...
Click to collapse
Turn of your phone & HOlD Volume Down & Connect USB of pc
I know this is very necro, but I've come to encounter the same problem. However my situation is weirder. I did very similar steps: wanted to go to stock and used SRK Toolkit to flash the recovery and relock the bootloader, I'm guessing it was not the correct twrp version for my current os. I should state that I don't understand anything about how huawei works... by now I just want the damn thing to boot . My situation is that the phone vibrates and displays the huawei bootlogo and then hangs. I've let the battery die and then do the Vol- + Usb thing but it doesn't give a f***. It just keeps going to the huawei logo. I've already ordered a pentalobe screwdriver on amazon to try and disconnect the battery cable...maybe it'll make a difference, since its kinda sketchy to try to let it die but no so much that it won't even boot and just shows the charging icon...:angel: ***fingers crossed*** anyways if someone has any hints I'd aprecciate it. Wish me luck, cheers
Edit: today, 3 days later, I re-tried to enter fastboot with vol - and usb in pc and IT WORKED!! unlocked the bootloader and now everything is fine.
Thread Closed
tell what you did, to brick phone.
what android version was before, what android wersion you tried to instal, what recovery you used. ?
oh, but if fastboot isnt working, you more or less are done. if im correct, even dc phoenix use fastboot..
"Step 1
Write compatible UPDATE.APP file in fastboot with DC Phoenix"
Arnys said:
tell what you did, to brick phone.
what android version was before, what android wersion you tried to instal, what recovery you used. ?
oh, but if fastboot isnt working, you more or less are done. if im correct, even dc phoenix use fastboot..
"Step 1
Write compatible UPDATE.APP file in fastboot with DC Phoenix"
Click to expand...
Click to collapse
i just use the SRKTool Lod Chan and try to unlocked the bootloader
and it success , after that i proceed to replace recovery with TWRP
but doesn't work . afterwards i bring back to re-lock bootloader
then the phone reboot . the phone stuck at android boot logo
no recovery no fastboot cannot identify even in PC
but when the phone gets drain and i plugged the charger on it
the phone reboots directly into the system or its OS
but when i try to power it off again ( reboot )
the same thing happen it will stuck in the boot logo
until the battery dries again ,.
i never upgrade to Nougat so my phone still in Marshmallow version
thank you .
vinfrix said:
i just use the SRKTool Lod Chan and try to unlocked the bootloader
and it success , after that i proceed to replace recovery with TWRP
but doesn't work . afterwards i bring back to re-lock bootloader
then the phone reboot . the phone stuck at android boot logo
no recovery no fastboot cannot identify even in PC
but when the phone gets drain and i plugged the charger on it
the phone reboots directly into the system or its OS
but when i try to power it off again ( reboot )
the same thing happen it will stuck in the boot logo
until the battery dries again ,.
i never upgrade to Nougat so my phone still in Marshmallow version
thank you .
Click to expand...
Click to collapse
what wersion of twrp ? link. there are MM and N versions, and, if you on MM put N version twrp, you will brick phone.. and, even with dead battery i was able to enter fastboot, when i instaled wrong twrp. but for me solution was simple, instal right twrp and all was good (ofcorse if you didnt delete system)
i can't remember the version but im sure it all arounds in 2.1...something
no i wasn't load the Nougat version because i know i am MM the only thing i remember is the TWRP i load is from SRKTool Lod Chong there was an option there to install twrp recovery
can i be able to enter the fastboot ?
if i can go over to fastboot i can repair this
but i can't go fastboot
volume rocker technique doesn't work
even using adb reboot bootloader too
when i am doing volume down ( hold )
the phone only vibrates then stuck at logo
even when its connected to adb command
when the phone reboot it stuck at the logo
can't go to fastboot ?
is there any way of forced
reflash the boot.img & recovery.img?
Hi, i have P9 L19 with C432 B210 i want to update do Android 7, but mistakely put wrong UPDATE to phone memory. Now I'm stucked at Huawei logo and cant turn off device.
Only I can get to Fastboot&Rescue Mode. After press all three buttons nothing happened, phone juest restarts and stuck at logo. I tried put right UPDATE to SD card but no luck
Bootloader: locked
FRP: locked
debbuging: off
Please help me.
no one knows how to fix our problem so sad
Please close the thread
problem issue solved!
please help me same problem as you...
JCB117 said:
please help me same problem as you...
Click to expand...
Click to collapse
Easily Unbrick Your Phone via this method
https://forum.xda-developers.com/p9/help/huawei-p9-brick-easiest-to-unbrick-t3662350
Hi, I have P10 VTRL09 .. A couple days ago i did relock bootloader and now i can not enter my phone.it stuck at Error mode.
I tried almost every method but it always comes back to error mode. I discharge the batterry and charge, if I am lucky, sometimes it will boot into the system but it will black out. I can not do anything except turn off, but while it was in this stage, i could connect to pc and get detected. pc try to install MTP driver but it also failed. I tried command in adb, it also failed (waiting for devices) ....
Issues :
1.boot loader locked
2.no recovery ( can not be load )
3.can not enter fastboot
4.can not force update
5.PC not detect
Question : Is there a way to make my phone go to fastboot ? so i can relock bootloader with adb and flash new firmware.
i appreciate all the help...please help me.
I have exactly the same issue. With identical error codes. Still trying to work out a solution.
on the Huawei website, the had a bootloader.img installer for older models but none for the p10/ p10 plus
Any advice would be appreciated
Let phone completely discharge even it power off automatically. Then put the phone on the charging it will boot up to system then go to settings >advanced settings>back up&reset> reset all settings
when it boot i cant see anything except black . i can only turn off or volume.
Connect with pc and press power and vol-
It should boot into fastboot. You got the error cause wrong or broken recovery.
Blackball said:
Connect with pc and press power and vol-
It should boot into fastboot. You got the error cause wrong or broken recovery.
Click to expand...
Click to collapse
it doenst work , i tried all combination. it always go to error when i tried. is it possible that some flash box could fix?
I never heard that someone killed his fastboot. Press longer the vol -
Bunnydollies said:
Hi, I have P10 VTRL09 .. A couple days ago i did relock bootloader and now i can not enter my phone.it stuck at Error mode.
I tried almost every method but it always comes back to error mode. I discharge the batterry and charge, if I am lucky, sometimes it will boot into the system but it will black out. I can not do anything except turn off, but while it was in this stage, i could connect to pc and get detected. pc try to install MTP driver but it also failed. I tried command in adb, it also failed (waiting for devices) ....
Issues :
1.boot loader locked
2.no recovery ( can not be load )
3.can not enter fastboot
4.can not force update
5.PC not detect
Question : Is there a way to make my phone go to fastboot ? so i can relock bootloader with adb and flash new firmware.
i appreciate all the help...please help me.
Click to expand...
Click to collapse
hi, did you already fixed your phone? I got the problem same as you, I have the device Huawei P10 VTR-L29.. I hope you can help me if you fixed it.. thanks,
rosarioglen18 said:
hi, did you already fixed your phone? I got the problem same as you, I have the device Huawei P10 VTR-L29.. I hope you can help me if you fixed it.. thanks,
Click to expand...
Click to collapse
sadly , i havent found any solution yet. sorry . i also wish to fix it
https://forum.xda-developers.com/p10/how-to/guide-unbricking-p10-using-hwota-windows-t3714416
or try this:
http://huafan.cz/discussion/4218/ro...ei-p10-a-postup-instalacie-do-telefonu#latest
it is in lsovakia language so use google translator.
DallasCZ said:
https://forum.xda-developers.com/p10/how-to/guide-unbricking-p10-using-hwota-windows-t3714416
or try this:
http://huafan.cz/discussion/4218/ro...ei-p10-a-postup-instalacie-do-telefonu#latest
it is in lsovakia language so use google translator.
Click to expand...
Click to collapse
thank you ,unfortunately it not possible to go to fastboot mode, when the phone on error state. pc also not detect. i apreciate the help.
1-the second link i posted is about to flash service stock firmware trough force update (vol+,vol-,power). have you tried?
2-what the phone does when you try to start the fastboot mode (connect with pc, turn phone off, turn phone on with vol- and power)?
3-what is your model number L09CxxxBxxx?
I have sam problem last 3 days and i cannot solwed
solution
Hi, I was able to solve it in this way.
Let the phone download 0% battery
connect it to the PC, pressing Vol - & power.
The phone will enter fastboot.
flashing the stock recovery
put the System in an SD and press vol + .vol - y pwr.
The phone will update and will light normally.
p10 no recovery
franmasco said:
Hi, I was able to solve it in this way.
Let the phone download 0% battery
connect it to the PC, pressing Vol - & power.
The phone will enter fastboot.
flashing the stock recovery
put the System in an SD and press vol + .vol - y pwr.
The phone will update and will light normally.
Click to expand...
Click to collapse
good morning guys I'm new, I have the same problem with huwei p10, unfortunately, eliminating supesu I deleted everything, now no longer works anything, ne adb ,, ne dload ,, can you help me? cel has 3 months of life ,,,
---------- Post added at 10:21 AM ---------- Previous post was at 10:09 AM ----------
fresigi said:
good morning guys I'm new, I have the same problem with huwei p10, unfortunately, eliminating supesu I deleted everything, now no longer works anything, ne adb ,, ne dload ,, can you help me? cel has 3 months of life ,,,
Click to expand...
Click to collapse
ps,,the model and VTR-L09 EUROPE, IF USE DLOAD, IS 5% BLOCK
p10 no recovery
Bunnydollies said:
Hi, I have P10 VTRL09 .. A couple days ago i did relock bootloader and now i can not enter my phone.it stuck at Error mode.
I tried almost every method but it always comes back to error mode. I discharge the batterry and charge, if I am lucky, sometimes it will boot into the system but it will black out. I can not do anything except turn off, but while it was in this stage, i could connect to pc and get detected. pc try to install MTP driver but it also failed. I tried command in adb, it also failed (waiting for devices) ....
Issues :
1.boot loader locked
2.no recovery ( can not be load )
3.can not enter fastboot
4.can not force update
5.PC not detect
Question : Is there a way to make my phone go to fastboot ? so i can relock bootloader with adb and flash new firmware.
i appreciate all the help...please help me.
Click to expand...
Click to collapse
Is there a way to make my phone go to fastboot ? so i can relock bootloader with adb and flash new firmware.
i appreciate all the help...please help me.[/QUOTE]
fresigi said:
Is there a way to make my phone go to fastboot ? so i can relock bootloader with adb and flash new firmware.
i appreciate all the help...please help me.
Click to expand...
Click to collapse
[/QUOTE]
Hi, I was having the same problem. Mate 8 EMUI 8.
After looking everywhere and trying all the options available, I wasnt able to resolve.
Finally, I tried FunkyHuawei and got my system back through eRecovery.
Gave them the readings like version no. , build no...etc through fastboot. The required info is on their site. They then reverted with a link of the firmware which I flashed through their FuHunbrick tool. It force updates the entire full last version.
After flashing and booting, the system didnt boot but was able to go to eRecovery and restored my previous version.
If you or anyone else stuck at this error, they can try at their own risk as they dont guarantee anything.
Edit: you should and will be able to boot into fastboot once the battery is totally down and phone shuts off completely. Just press volume down button and insert usb. Try again and again if it doesnt work first time.
Thanks.
Help
First sorry for my English
I have a similar issue:
Huawei P10 Lite
I managed to install TWRP, but when I did that I lost the OTA upgrades, then I tried to install the stock recovery and then the phone doesn't start. It just stay on the first screen (the one with the Huawei logo) and it gets hot as hell. The combination of keys doesn't work, the power key just reboot and gets back to the logo screen. I need your help guys, the phone is 3 month old. Thanks
elchino!!! said:
First sorry for my English
I have a similar issue:
Huawei P10 Lite
I managed to install TWRP, but when I did that I lost the OTA upgrades, then I tried to install the stock recovery and then the phone doesn't start. It just stay on the first screen (the one with the Huawei logo) and it gets hot as hell. The combination of keys doesn't work, the power key just reboot and gets back to the logo screen. I need your help guys, the phone is 3 month old. Thanks
Click to expand...
Click to collapse
Hi, let the phone battery dry out totally first. Totally. It should not vibrate at all when you press power button. Leave for a couple of hours more.
Then recharge to 50℅ or more and restart and see if you get to eRecovery or other options.
Are you getting any error screen after logo?
You will definitely get to fastboot by pressing volume down button and inserting usb. Try again n again.
apat26 said:
Hi, let the phone battery dry out totally first. Totally. It should not vibrate at all when you press power button. Leave for a couple of hours more.
Then recharge to 50℅ or more and restart and see if you get to eRecovery or other options.
Are you getting any error screen after logo?
You will definitely get to fastboot by pressing volume down button and inserting usb. Try again n again.
Click to expand...
Click to collapse
Hi. I did the battery part and the part of the pressing the vol - is and connecting to pc. It started but didn't got into fastboot or bootloader, just turned on normally and then I ran the adb command "adb reboot recovery" and I had to do the battery part again. I am afraid to run "adb reboot bootloader" because the risks of the draining out the battery. I mean my phone does not enter into recovery.
Hello Xda community,
I need help badly , I bricked my phone one week after receiving it !! My goal was to install Clarity kernel for better battery performance.
I try to tell you all the steps and informations you will need to help me :
1 - I unloacked bootloader using Mi unlock.
2 - I installed TWRP 3.1.1-0 and root my device this way : LINK (method 2)
3 - I flash in recovery mode last MIUI rom 9.5.5.0, phone still running well after that
4 - I boot in recovery and flash this firmware in order to flash Clarity Kernel after
5 - After flashing the firmware I reboot and Im stuck at MIUI logo. I can go to fastboot mode though. But unable to reach recovery mode neither switch off the phone.
6 - I install MiFlash and tried to flash different version of rom MIUI santoni from official website (9.5.5.0 / 8.2.10.0) neither work SEE IMAGE I tried with mi flash 2016.08.30 same result
I get different status on mi flash, one is (image not matching device), even though I think I did everything well.
7 - Since last try of flashing my computer does not even recognise my phone in fastboot mode like before :/ and MiFlash doesn't see my phone :/
Please give me some advice/clue to revive my phone :crying:
In advance I thank you so much :good:
I use Windows 10 - 64 bits
try booting recovery from fastboot "fastboot boot *twrp image*.img"
Niaph said:
Hello Xda community,
I need help badly , I bricked my phone one week after receiving it !! My goal was to install..........
In advance I thank you so much :good:
I use Windows 10 - 64 bits
Click to expand...
Click to collapse
Well i am not at all an expert in miui, infact this is my first mi phone. But i think this tool called xiaomi adb/fastboot tool can help u. Google it.... It is available in reddit. One piece of general advice : before any kind of experiment always keep a preparation for the worst case scenario. I think ur phone is stuck at boot. U can try to hold the power button for about 10-15 seconds to turn off. Also just relax and have patience... It will b solved. Let me know how it goes.
Niaph said:
Hello Xda community,
I need help badly , I bricked my phone one week after receiving it !! My goal was to install Clarity kernel for better battery performance.
I try to tell you all the steps and informations you will need to help me :
1 - I unloacked bootloader using Mi unlock.
2 - I installed TWRP 3.1.1-0 and root my device this way : LINK (method 2)
3 - I flash in recovery mode last MIUI rom 9.5.5.0, phone still running well after that
4 - I boot in recovery and flash this firmware in order to flash Clarity Kernel after
5 - After flashing the firmware I reboot and Im stuck at MIUI logo. I can go to fastboot mode though. But unable to reach recovery mode neither switch off the phone.
6 - I install MiFlash and tried to flash different version of rom MIUI santoni from official website (9.5.5.0 / 8.2.10.0) neither work SEE IMAGE I tried with mi flash 2016.08.30 same result
I get different status on mi flash, one is (image not matching device), even though I think I did everything well.
7 - Since last try of flashing my computer does not even recognise my phone in fastboot mode like before :/ and MiFlash doesn't see my phone :/
Please give me some advice/clue to revive my phone :crying:
In advance I thank you so much :good:
I use Windows 10 - 64 bits
Click to expand...
Click to collapse
Nevermind I misread... If you think clarity or the firmware messed up your phone I could give you my kernel and firmware for you to restore it
Though if you're desperate for a solution, I'd transfer a ROM into your phone and start over with it, you can flash MIUI also by flashing https://drive.google.com/file/d/0ByWEieei-0nyMTR4R0dxWk9BTms/view after it
Your version of miflash is a little bit outdated! The last One is from may, last year if my memory doesnt fail. Install latest version of miflash and try to flash again stock ROM.
You can try also flashing stock ROM with miflash but in edl mode (emergency download mode) , instead of fastboot mode, but to do that you have to acess stock recovery, and then use this command " adb reboot edl", connect your phone to PC, and then see of detects, then flash then stock ROM. To acess stock recovery, press volume up + Power, if that not works, press volume up + volume down+ Power. Hope i helped
Ok I solved the problem using this method.
So I removed back cover, disconnected battery, connected the 2 points with a twizzer then flashed STOCK rom and it worked!! So relieved!
Thank you for the help anyway.
Speaker87 said:
Your version of miflash is a little bit outdated! The last One is from may, last year if my memory doesnt fail. Install latest version of miflash and try to flash again stock ROM.
You can try also flashing stock ROM with miflash but in edl mode (emergency download mode) , instead of fastboot mode, but to do that you have to acess stock recovery, and then use this command " adb reboot edl", connect your phone to PC, and then see of detects, then flash then stock ROM. To acess stock recovery, press volume up + Power, if that not works, press volume up + volume down+ Power. Hope i helped
Click to expand...
Click to collapse
Dear sir,
flashing redmi4 with miflash tool in edl shows me "object reference is not set to an instance of the object". Any solution please. This was second time i try flashing soft bricked redmi4 , first time few days ago flashed successfully and was using it properly in edl with miflash tool. Then During downloading update shown in setting by ota and rebooting it, and again got stuck on mi logo, means softbricked again.but try edl this time gives an error mentioned.
Speaker87 said:
Your version of miflash is a little bit outdated! The last One is from may, last year if my memory doesnt fail. Install latest version of miflash and try to flash again stock ROM.
You can try also flashing stock ROM with miflash but in edl mode (emergency download mode) , instead of fastboot mode, but to do that you have to acess stock recovery, and then use this command " adb reboot edl", connect your phone to PC, and then see of detects, then flash then stock ROM. To acess stock recovery, press volume up + Power, if that not works, press volume up + volume down+ Power. Hope i helped
Click to expand...
Click to collapse
chandan shah said:
Dear sir,
flashing redmi4 with miflash tool in edl shows me "object reference is not set to an instance of the object". Any solution please. This was second time i try flashing soft bricked redmi4 , first time few days ago flashed successfully and was using it properly in edl with miflash tool. Then During downloading update shown in setting by ota and rebooting it, and again got stuck on mi logo, means softbricked again.but try edl this time gives an error mentioned.
Click to expand...
Click to collapse
Problem solved.
I got revived my redmi 4 again from softbricked locked bootloader,
By trying an older rom
santoni_global_images_V8.2.12.0.MAMMIEA_20170629.0000.00_6.0_global_751410291c.tgzWith miflash-20220218 in edl mode .
A couple days ago my Redmi Note 9 (merlin) 4/128 GB NFC automically installed the Update from V12.0.3.0.QJOEUXM to V12.0.4.0.QJOEUXM over night. I had rooted and installed a TWRP on it. As I had noticed that it was not rooted anymore I tried to reflash the TWRP over Fastboot because it was overwritten by MIUI. When I tried to boot the twrp.img the phone did so and the screen was on but black. After 4 or 5 tries it hanged up in a bootloop and I cannot access Fastboot Mode or something else anylonger.
Is there something left I can try?
Already tried power and minus option.when you connect to a desktop what does it say ?
Dokrak99 said:
Already tried power and minus option.when you connect to a desktop what does it say ?
Click to expand...
Click to collapse
It goes on and Windows makes the sound for a new device connected, and then it goes off again, and Windows makes the sound for disconnecting a device. This repeats for around 4 or 5 minutes then it goes finally off.
That's bad.
Hold the power +/- longer then 15 seconds try both.
Second
Charge for about 10 minutes and try the same again.
Last drain it when down keep pushing the power button to flat it.hook it up on desktop and install miflashtools.or try power +/- again
Dokrak99 said:
Hold the power +/- longer then 15 seconds try both.
Click to expand...
Click to collapse
Same as:
LordRedstone05 said:
It goes on and Windows makes the sound for a new device connected, and then it goes off again, and Windows makes the sound for disconnecting a device. This repeats for around 4 or 5 minutes then it goes finally off.
Click to expand...
Click to collapse
Dokrak99 said:
Charge for about 10 minutes and try the same again.
Click to expand...
Click to collapse
When I try to charge it it goes in the bootloop again until I disconnect it and the battery runs out.
Dokrak99 said:
Last drain it when down keep pushing the power button to flat it.
Click to expand...
Click to collapse
It goes on, shows this battery icon, that it's empty and goes off. This repeats until I release the button.
Dokrak99 said:
hook it up on desktop and install miflashtools.or try power +/- again
Click to expand...
Click to collapse
The miflashtool does nothing when I click on Flash with the images and scripts loaded. Power +/- does the same as before.
Sorry I thought flash tools had a option in top for selecting boot options.There is a mi tool around where can select the boot options.i need to search on my desktop what it was.we need to trigger it in fastboot/recovery mode some how.most likely it was xiaomi tools V2 but I really need to check it.tools V2 got a bricked option do.but since it restarts everytime it's pretty long shot
Dokrak99 said:
Sorry I thought flash tools had a option in top for selecting boot options.There is a mi tool around where can select the boot options.i need to search on my desktop what it was.we need to trigger it in fastboot/recovery mode some how.most likely it was xiaomi tools V2 but I really need to check it.tools V2 got a bricked option do.but since it restarts everytime it's pretty long shot
Click to expand...
Click to collapse
Thanks in advance
What should I do in this tool? The tool doesn't recognize my phone. It brings nothing since I cannot access Fastboot.
Well basically there is only one real option left . contact mi service center because mi don't support or they closed there download,edl support on there phones to prevent rom swapping .there is a edl cable with mtk support around but that's a long shot.because I never had a messed up phone like this.at least not one with mtk.without recognise you're desktop I don't see a fix in this to get in fastboot or flash it.
Download platform tools drop it on c:/ so c:/platform tools .install abd drivers package if you didn't have it.go in platform tools the top line and tick Cmd hit enter.try command : fastboot devices .try a few times if a number pops up you can try .fastboot reboot fastboot
LordRedstone05 said:
A couple days ago my Redmi Note 9 (merlin) 4/128 GB NFC automically installed the Update from V12.0.3.0.QJOEUXM to V12.0.4.0.QJOEUXM over night. I had rooted and installed a TWRP on it. As I had noticed that it was not rooted anymore I tried to reflash the TWRP over Fastboot because it was overwritten by MIUI. When I tried to boot the twrp.img the phone did so and the screen was on but black. After 4 or 5 tries it hanged up in a bootloop and I cannot access Fastboot Mode or something else anylonger.
Is there something left I can try?
Click to expand...
Click to collapse
TWRP bricked my redmi Note 9 too, but i had ADB Connection in the black Screen so i rebooted to Fastboot over ADB and reflashed the Stock rom
LordRedstone05 said:
A couple days ago my Redmi Note 9 (merlin) 4/128 GB NFC automically installed the Update from V12.0.3.0.QJOEUXM to V12.0.4.0.QJOEUXM over night. I had rooted and installed a TWRP on it. As I had noticed that it was not rooted anymore I tried to reflash the TWRP over Fastboot because it was overwritten by MIUI. When I tried to boot the twrp.img the phone did so and the screen was on but black. After 4 or 5 tries it hanged up in a bootloop and I cannot access Fastboot Mode or something else anylonger.
Is there something left I can try?
Click to expand...
Click to collapse
Did you find solution on this? Please answer bro i need your help
Jayson Galang said:
Did you find solution on this? Please answer bro i need your help
Click to expand...
Click to collapse
Unfortunately i haven't found a solution. I had to send it to a service center 2 Days ago. Sorry, that i couldn't help.
the right driver is mtk this is not adb nothing happens the this you could fixs is
go to the nearest techniciann beacause they need special tools to fix properly
Is your phone still bricked, If yes, I can provide link for the factory firmware recently released for Merlin, You could give flashing that in SP Flash a try, does not need auth account.
If your device keep booting in recovery (or blackscreen), you need to erase misc partition.
Here, is the guide for erasing MISC partition: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4209299/
Good luck
Do you need help with your MERLIN device ?
Read this FAQ: https://forum.xda-developers.com/t/...for-merlin-redmi-10x-4g-redmi-note-9.4225177/
Communos said:
Is your phone still bricked, If yes, I can provide link for the factory firmware recently leaked for Merlin, You could give flashing that in SP Flash a try, does not need auth account.
Click to expand...
Click to collapse
yow is that legit? Had my redmi note 9 bricked for a week now.
CruisaderX said:
yow is that legit? Had my redmi note 9 bricked for a week now.
Click to expand...
Click to collapse
If you got bootloop after flashed magisk, you need to flash stock rom boot.img.
If you got bootloop after flashed TWRP, you need to flash stock rom recovery.img.
If you got bootloop (or black screen) after flashed misc partition, you need to erase misc partition.
If it keeps restarting, you've made any wrong modification. You need to follow your steps back and try to unmake your modification.
If you can't enter in fastboot mode or recovery mode, you need to flash stock rom using sp flash tool.
If you are using V12.0.4.0 or lower, you can flash without EDL and authentication.
If you are using V12.0.5.0 or higher, you need EDL and authentication for flashing.
If you are using V12.0.5.0 or higher, TWRP will not work.
If you want to use sp flash tool, you need to flash the stock rom preloader using V12.0.4.0 (or lower). (It will works perfectly with lower preloader binary version).
With an older preloader version, your phone will can receive DA files and accept flashing with NO auth.
Everything you need to do is plug your phone in usb (without press any key, if you press any key it will enter in EDL mode and requests authenticaion).
Here, are PRELOADER binaries for flashing: https://forum.xda-developers.com/t/...omi-redmi-10x-4g-xiaomi-redmi-note-9.4221081/
Here, are DA files for flashing using flash tool: https://forum.xda-developers.com/t/...omi-redmi-10x-4g-xiaomi-redmi-note-9.4209767/
Here, you can find boot images for original stock and magisk patched: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4204671/
If you want to keep TWRP working on V12.0.5.0 or higher, you need to flash the stock rom lk partition using V12.0.4.0 (or lower). (It will works perfectly with lower lk partition version).
Here, are LK images for flashing: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4218925/
If you want to disable TWRP, you need to flash stock rom recovery partition.
Here, are RECOVERY images for flashing: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4204671/
If your device keep booting in recovery (or blackscreen), you need to erase misc partition.
Here, is the guide for erasing MISC partition: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4209299/
If you want to know what is working for MERLIN, take a look: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4204873/
Good luck
Do you need help with your MERLIN device ?
Read this FAQ: https://forum.xda-developers.com/t/...for-merlin-redmi-10x-4g-redmi-note-9.4225177/
VD171 said:
If you got bootloop after flashed magisk, you need to flash stock rom boot.img.
If you got bootloop after flashed TWRP, you need to flash stock rom recovery.img.
If you got bootloop (or black screen) after flashed misc partition, you need to erase misc partition.
If you are using V12.0.5.0 or higher, TWRP will not work.
Here, you can find boot images for original stock and magisk patched: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4204671/
If you want to keep TWRP working on V12.0.5.0 or higher, you need to flash the stock rom lk partition using V12.0.4.0 (or lower). (It will works perfectly with lower lk partition version).
Here, are LK images for flashing: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4218925/
If you want to disable TWRP, you need to flash stock rom recovery partition.
Here, are RECOVERY images for flashing: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4204671/
If your device keep booting in recovery (or blackscreen), you need to erase misc partition.
Here, is the guide for erasing MISC partition: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4209299/
If you want to know what is working for MERLIN, take a look: https://forum.xda-developers.com/t/...omi-redmi-note-9-xiaomi-redmi-10x-4g.4204873/
Good luck
[/QUOTE
Click to expand...
Click to collapse
I tried actually before after failed attempt of flashing twrp. First, I got my redmi note 9 bricked after following one of the guides posted here (rooting), I will call this state 1 brick. In state 1 brick you can still access fastboot mode normally. Then i tried to flash twrp hoping to just flash a rom to fix it leading to state 2 brick. In state 2 brick, it seems like it is stucked on recovery (btw the recovery is only displaying black screen) and is classifying fastboot as the bootloader, meaning you can boot into fastboot using adb command reboot bootloader. Then I followed one of the guides here again and then it managed to lead my device to state 3 brick. In state 3 brick it continuously boot looping only displaying the boot image for a second then repeat. Normally it can be fixed by flashing a stock rom using sp flash tool but not with xiaomi devices. Now I am stucked with a hard bricked note 9 with no way of fixing.
CruisaderX said:
i tried before actually after failed attempt of flashing twrp. First, I got my redmi note 9 bricked after following one of the guides posted here (rooting, I will call this state 1 brick. In state 1 brick you can still access fastboot mode. Then i tried to flash twrp hoping to just flash a rom leading to state 2 brick. In state 2 brick, it seems like it is stucked on recovery (btw the recovery is only displaying black screen) and is classifying fastboot as the bootloader, meaning you can boot into fastboot using adb command reboot boot loader. Then I followed one of the guides here again and then it managed to lead my device to state 3 brick. In state 3 brick it continuously boot looping only displaying the boot image for a second then repeat. Normally it can be fixed by flashing a stock rom using sp flash tool but not with xiaomi device. Now I am stucked with a hard bricked note 9 with no way of fixing.
Click to expand...
Click to collapse
You need to read every line and every word careful and follow only specific guide for your specific problem.
If you try to do anything you see, obviously you will cause more damages to your device.
Please, read my post again: https://forum.xda-developers.com/t/redmi-note-9-merlin-4-128-nfc-hard-brick.4201717/post-84379823
If you can't enter in fastboot mode or recovery mode, you need to flash stock rom using sp flash tool.
If you are using V12.0.4.0 or lower, you can flash without EDL and authentication.
If you are using V12.0.5.0 or higher, you need EDL and authentication for flashing.
Do you need help with your MERLIN device ?
Read this FAQ: https://forum.xda-developers.com/t/...for-merlin-redmi-10x-4g-redmi-note-9.4225177/