So here its my problem.
These tablet SM-T230NU was completely brand new but I found problems to connect to wifi and bluetooth, did a little research and found that it was solved updating the firmware. so I downloaded everything needed, opened odin and when entered the tab on download mode, pressing volume down to confirm and finally found I had downloaded the wrong firmware for this model, before doing anything I decided to donwload the correct one and because of the message saying Do not turn off the target I kept the tablet plugged while downloading the new firmware, I prevented pc from sleeping so I thought it will be okay to kept the tablet on odin mode because I didnt know how exit it.
The file was huge so I waited for around 8 hours, and somehow the tablet got disconeccted ( not the cable) and odin didnt recognize neither my pc.
It wont turn on too.
I was panicked so Itried unplugging and re-plugging ( no sense) it and the battery icon did appear and some warning mesage so fast I could not see anything.
I dont have an idea what happened.
There is a chance for fix it?
Thank you very much
This is the history if it helps...
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
Just wanted to say I put in charging on a main supply and apparently it rebooted normally .Still I dont know how fix the wifi issue.
Related
Good Day All :
I started up with Odin so i could update the Tab, but the program closed down about 1-2 sec. after. When I tried to turn on the tablet, there was ... no reaction (!)
Tried to go in "download mode", but no reaction or by factory-reset. just black screen ...
i also tried "Recovery Code" (Hold the Vol Down Key + Vol Up Key + Power Key for 15 seconds then release) but its same no reaction.
Can it really be true that I have ended up with a piece of useless plastic?
Pls your help is vevry important
thanks
Do not panic.
Better connect to wall charger for an hour first; then try recovery mode (volume up + power).
Regards
Kongar
thanks for the reply.
it was in the wall charger for an 7 hour . i just try ... nothing happend ...
It sounds like you have stopped it in the middle of loading the bootloaders... That almost the only way to hard brick your tab...
If you can't get it recognised by ODIN then the only thing available is to JTag it. You need to send it in to someone who can do this - look around the general forum, there was someone there doing it - most phone repair places will say it needs motherboard replaced, expensive.
If its still in warranty, you might be able to send back to samsung, tell them it happened while flashing through Kies.... Don't tell them you flashed with ODIN.
Seems like a few people are doing this...
Good Luck...
ok, now after i update the PIT the GT is boteabel but its hange in the startup page GALAXY Tap.
Note : Every time i but the GT in the Dawnloading Mode and try to flash a rom i get faild in kernel stage.
any help Pls ...
<ID:0/014> Added!!
<ID:0/014> Odin v.3 engine (ID:14)..
<ID:0/014> File analysis..
<ID:0/014> SetupConnection..
<ID:0/014> Initialzation..
<ID:0/014> Get PIT for mapping..
<ID:0/014> Firmware update start..
<ID:0/014> zImage
<ID:0/014>
<ID:0/014> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
that is mean the kernel is not signed
http://forum.xda-developers.com/showthread.php?t=1133590
check here
thanks Dude for the information. i think my solution somewhere in that post but i am new with Samsung GT. i can’t understand anything of that post.
can someone Pls explain to me how to do it in step by step
Thanks
ok, i think i get it . i will do that way and i will see what happend with me ...
Fainaly My Tab Is working .......
thanks every one
ksadude said:
Fainaly My Tab Is working .......
thanks every one
Click to expand...
Click to collapse
glad to see you up and running
an advice , if you are in froyo before flashing un Official roms\kernels please patch the bootloader apk before you go through anything , if you are now at gingerbread then flash wtf is coming in your way but only what made for your tab
Flash Safe
Hi
I bought me a 2nd hand galaxy note yesterday but was on 2.3.6 Ginger minger so this morning proceeded to update to ICS via KIES
stuck on 3% for 10 mins then on 4% reported an error, ever since I have been unable to follow any recovery options
Problem I have now is running Odin 1.85 with "N7000XXLRG_N7000DBTLRG_N7000XXLRB_HOME.tar.md5"
I am only able to boot into download mode not recovery but when I connect the USB cable, big fat nothing!!!!!!!!!!!!!
Can anyone help me please
PS: I know how tetchy mods can be when you post in wrong section so apologies in advance
Cheers
EFC
if you connect the phone on download mode to your PC, does odin detect your note??
you can flash ICS even if the screen shows nothing as long as it gets detected by odin
musashiro said:
if you connect the phone on download mode to your PC, does odin detect your note??
Click to expand...
Click to collapse
Nope, and nor do I get the windows noise when you have plugged in a USB device like a mouse or something!!
I have re-installed the Samsung USB drivers twice both times it said they were already installed but I done it anyway
Does this sound fixable? Would a phone shop only try same recovery options that I am trying?
ok, let me get this straight..
you have download mode, no recovery right?
if you boot into download mode, then connect the phone, it doesn't get detected (blank screen) ?? have you tried charging the device then trying to connect again? or simply remove the battery then re-insert?
musashiro said:
ok, let me get this straight..
you have download mode, no recovery right?
if you boot into download mode, then connect the phone, it doesn't get detected (blank screen) ?? have you tried charging the device then trying to connect again? or simply remove the battery then re-insert?
Click to expand...
Click to collapse
Does not go blank says "Downloading... Do not turn off target !!"
Battery was full before I started this so I doubt its in need of a charge
Odin does not report any connecting in the Message box, tried on a different PC even installing "SAMSUNG_USB_Driver_for_Mobile_Phones" but still nothing
So I can asume that the issue with not connecting to Odin is with the phone
Question is.....what is my next move?
Thanks for your help much appreciated
EFC
I just borrowed a USB cable from my neighbour and BAM!!!
<ID:0/003> Added!!
But then...after clicking START this is the Message log
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLRG_N7000DBTLRG_N7000XXLRB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003>
<ID:0/003> Receive Response form LOKE
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help
Thanks
musashiro said:
if you connect the phone on download mode to your PC, does odin detect your note??
you can flash ICS even if the screen shows nothing as long as it gets detected by odin
Click to expand...
Click to collapse
I have given up, been trying since 10 this morning
Samsung has gone right down in my estimation due to this, all I done was install KIES and was when phone connected it prompted me to install an updated firmware, then got error at 4%
Never had this with HTC so if I cant get a warranty replacement am screwed!!!
Was Your phone locked or something before this happened ?
Maybe you could try a new Rom File...
sahilarora2003 said:
Was Your phone locked or something before this happened ?
Maybe you could try a new Rom File...
Click to expand...
Click to collapse
I have tried 3 different firmwares 2 of them FAIL in Odin while 1 gets stuck on "setup connection"
It is in Warranty so are Vodafone going to want to attempt a repair or will it be a straight swap?
EFCLEE said:
I have tried 3 different firmwares 2 of them FAIL in Odin while 1 gets stuck on "setup connection"
It is in Warranty so are Vodafone going to want to attempt a repair or will it be a straight swap?
Click to expand...
Click to collapse
I think it will be a repair as its not a hardware fault I think.
Use ODIN 1.85. Maybe a last try before returning it to Service Centre ?
And don't change any option in ODIN. I think you have changed it.. Maybe I am wrong lol... Just wondering...
try to flash any custom kernel only with odin, not firmware, and if the kernel flashed, try to go to recovery and then full wipe and flash any rom.
Sent from my GT-N7000 using xda premium
restart your phone again in download mode b4 trying again in ODIN... donot continue where its stuck
The issue with mine is i have no history on this phone... its my co-workers who got it from a friend who is clueless about his own damn phone.... bought from a local guy.
anyways im in guam and i have no way of checking if this model was on a custom rom or what not or if the unit was pure stock all around i cant go into recovery mode at all only into ODIN which tells me to download a custom OS ... i myself am not a tech guy so im new to this just reading around but you all are well aware of what firmware and what not your unit was on but me i have no clue due to it not being able to fully start up and not charging only through my laptop port which at that wont even help cause my laptop tells me its not recognized but i have the drivers downloaded in already and have kies from my previous androids i had.
so my search is to find someone who can help me out here with me not knowing at all pretty much being blind to what the units firmware or ROM was even on and so forth.
further info
James Cortez671 said:
The issue with mine is i have no history on this phone... its my co-workers who got it from a friend who is clueless about his own damn phone.... bought from a local guy.
anyways im in guam and i have no way of checking if this model was on a custom rom or what not or if the unit was pure stock all around i cant go into recovery mode at all only into ODIN which tells me to download a custom OS ... i myself am not a tech guy so im new to this just reading around but you all are well aware of what firmware and what not your unit was on but me i have no clue due to it not being able to fully start up and not charging only through my laptop port which at that wont even help cause my laptop tells me its not recognized but i have the drivers downloaded in already and have kies from my previous androids i had.
so my search is to find someone who can help me out here with me not knowing at all pretty much being blind to what the units firmware or ROM was even on and so forth.
Click to expand...
Click to collapse
i downloaded a old ROM 2.3.5 i believe or somewhat and put it in my PC odin PDA put my phone into odin mode tab turned yellow. dowloaded as well the 16gb model PIT given by Dr.Ketan and also got emmsc brick PIT just in case now on my odin i just put in the PDA of the india version of an old rom for direct root accessability and so forth... the usual timing for the odin says 5-10 min. but mine is taking quite some time really....
more info
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKK3_N7000ODDKK1_N7000DDKJ3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
thats what my panel remains on
Do you know recovery mode?
Press volume up button, power button and home button together for 10 secs and release. Tell us what happens.
Also read drketan guide how to flash gb rom.
Sent from my GT-N7000 using xda premium
dsmas said:
Do you know recovery mode?
Press volume up button, power button and home button together for 10 secs and release. Tell us what happens.
Also read drketan guide how to flash gb rom.
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
i did Dr.Ketan guide im still awaiting response right now this is what it is stuck on right now
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKK3_N7000ODDKK1_N7000DDKJ3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
i cant get the phone into recovery mode...... it just reboots to the boot screen and just stays there......
i dont know the previous OS on this phone or ROM or KERNEL cause i got it dead and stuck like so .... right now im still waiting for a response from the odin
Maybe i could help you
1st : can you remove you phone battery and tell us your phone model ?
2nd : put the battery in and charge your phone without booting ,, is it turning into a battery icon ? if so continue charging at least to more than half the battery
3rd : if your device is surly a gt-n7000 try to download another rom and after that check its csc before flashing , jelly bean update seems awesome right now ! .... i could tell you to download this amazing stock - rom but i need to make sure of your phone model first !
sniper9911 said:
1st : can you remove you phone battery and tell us your phone model ?
2nd : put the battery in and charge your phone without booting ,, is it turning into a battery icon ? if so continue charging at least to more than half the battery
3rd : if your device is surly a gt-n7000 try to download another rom and after that check its csc before flashing , jelly bean update seems awesome right now ! .... i could tell you to download this amazing stock - rom but i need to make sure of your phone model first !
Click to expand...
Click to collapse
yes the device is surely a GT-N7000 ill charge the battery and yes it shows the charging icon and can charge......
no help
still its a fail
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKK3_N7000ODDKK1_N7000DDKJ3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
that is as far as i get then it just says fail...... my phone will only charge when connected to my laptop but not to my wall charger. my phone can enter download mode but not recovery mode.
when connected to my laptop the driver doesnt recognize it but it can be detected on odin but on kies it wont.
more help
okay ..... so its either the rom itself you are trying to flash or something else ....
first : what do you mean when you charge it from the plug it wont go ?? this is a real problem ... if you have another charger try it with first then if its not charging you'll need to service that mobile via samsung service center cause you cant do anything with an empty battery ....
if my guess is right then it a faulty charger and you need a new charger ... thats it , after checking this step you can try downloading another rom which i am sure it will be all right cause i am already using it :
try this link :
http://www.hotfile.com/dl/198300717/4646e97/N7000JPLSB_N7000OJPLSA_XSG.zip.html
download this version of odin too :
http://www.4shared.com/get/U6DTV0GA/gt-n7000_flasher__pit.html
you'll need to uninstall samsung kies , reboot you pc ,
and install samsung latest usb drivers :
http://forum.xda-developers.com/showthread.php?t=2038555
Note : DO NOT FLASH ANY FIRMWARE UNLESS YOU HAVE GOTTEN DEVICE IS READY TO USE AND ALL DRIVERS INSTALLED SUCCESSFULLY
afterwards you will extract odin and the firmware (md5 file + dll file "important" ) on you desktop in a folder and then you'll use odin in administrator mode then you make sure you note battery > 50% at least then make your note in odin mode ( vol down + home + power , then vol up to enter odin mode )
plug your note to usb and let the pc reapply drivers then youll put md5 file in pda bar and pit 16 gb in pit , also check your note internal capacity ... maybe you are lucky and have 32gb or even 64gb
okay then press start .... normally it would take less than 10 minutes to complete , 8 minutes 15 seconds of waiting then you have your note booting , unplug it from pc when odin says ok ( blue ) or pass ( green ) then here you go ... Jelly bean !!
teah man still no damn luck it keeps on failing and if it aint failed yet its like passed 30min. and still nothing changed.... do i put the PIT and the PDA or do i do it one by one.... do the GT7000 PIT first then the N7000 PDA after?!....
a step by step video would do more wonders than just reading.... cause i think my issue is way different cause i dont even know if this phone is unlocked or what or anything about it cause i got it bricked. stuck on boot logo and HARD RESET isnt accessible and im in GUAM.... ya know where GUAM is?!......
Me having same issue guys :crying: i am following this thread please experts help us !!
TRY booting in recovery or download mode.
recovery : volume up+home+power at the same time
download : volume down+home++power at the same time.
let us know if you can get into both or any of these modes
Mayank Chandwani said:
TRY booting in recovery or download mode.
recovery : volume up+home+power at the same time
download : volume down+home++power at the same time.
let us know if you can get into both or any of these modes
Click to expand...
Click to collapse
Not working mate
Sent from my GT-N7000 using xda premium
LucknowBoy said:
Not working mate
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
How long did you press/hold the buttons? In what order?
YEY!
thanks alot sniper9911 you're a live saver.., i follow the procedure that you've said then my problem solve
thanks again!
James Cortez671 said:
teah man still no damn luck it keeps on failing and if it aint failed yet its like passed 30min. and still nothing changed.... do i put the PIT and the PDA or do i do it one by one.... do the GT7000 PIT first then the N7000 PDA after?!....
a step by step video would do more wonders than just reading.... cause i think my issue is way different cause i dont even know if this phone is unlocked or what or anything about it cause i got it bricked. stuck on boot logo and HARD RESET isnt accessible and im in GUAM.... ya know where GUAM is?!......
Click to expand...
Click to collapse
Well, I´m with the same problem here on this side but i thinck this might work:
Check this link: http://forum.xda-developers.com/showthread.php?t=1901191 I dont know if this is going to work but i am going to run this in my samsung.
After that, I will reply you.
can someone help me...my n7000 just went off...i tried to start it,but loops on samsung logo. i used odin with stock rom...all went right it finished with Pass from the first try...but then again the phone didint want to start...i started updating apps and then looped again...every time it shows battery totaly empty...i tried a couple of times with odin and even pit file...even managed one time to start the phone,opened setting etc...battery indicator showed its full,and then suddenly phone just restarts and i cant do nothing?!
last time it rebooted automaticly opens android recovery and stays on that screen....? i cant do nothing....every time i plug it into charger he starts up and opens recovery ?
tried charging over computer usb,from a 220v,even from a dock....but he as soon as i plug it he opens recovery ?? any help...i think the main problem is battery....would it help to charge it in some other device or something ? or i screwed things big time ?
I had the same issue here.use odin still cant help
Anyone can help here
I stuck here.
<ID:0/003>NAND Write Start!!
Hi, I have a Samsung galaxy S3 mini and I'm stuck in some kind of download mode that keeps turning off and on by itself. the phone constantly gets disconnected and reconnected from and to the pc all in matter of seconds...
I tried to update my phone but mid process odin fail and the phone never turned on again. Just to go download mode. Since then I have been getting the error:
"Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I know I can probably solve the problem in Kies or odin but I can't because the conecting on and off problem... The pc recognises it but in 1 or 2 seconds disconects and again and again. (I think the problem its not the drivers since it recognises it)
Odin log keeps going like this:
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<ID:0/005> Removed!!
If anyone have some idea please help
Background, Symptoms and Repair Attempts
My significant other's I9305 spontaneously died. The phone is fully stock, non-rooted. Was never custom-flashed.
It was working with no apparent problems, then one night we left it (turned on) to recharge overnight, as we usually do, and found it boot-looping in the morning.
"Boot-looping": repeatedly showing "Samsung Galaxy S3" screen for about 4 seconds, then restarts (screen goes black for about 3 seconds, then "Samsung Galaxy S3" screen shows again, infinitely repeating).
The boot-loop prevents access to recovery mode or to the main OS.
"Charge mode" is working - when phone is turned off, it shows charge animation when connected to power source (with battery level rising as charging progresses).
Download mode itself is accessible, and phone remains in it until I force it to end. Text shown on top of download mode screen:
Code:
ODIN MODE
PRODUCT NAME: GT-I9305
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
However, actual flashing is apparently impossible. I tried several times using Odin v3.09 to flash 2 different stock images:
I9305XXBME3_I9305DBTBMF1_I9305XXBME1 (Stock 4.1.2)
I9305XXUFNL1_I9305DBTFNL1_I9305XXUFOA1 (Stock 4.4.4)
In all my flashing attempts I had only "AP", "Auto Reboot" and "F. Reset Time" checkboxes checked, and the rest unchecked.
All attempts failed (with a red "FAIL!" on the top-left of the window) within 2-3 seconds after clicking the "Start" button. Odin's message log for such an attempt is as follows:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9305XXBME3_I9305DBTBMF1_I9305XXBME1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> tz.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I also tried using Odin to flash 2 different custom recovery images:
openrecovery-twrp-3.0.2-1-i9305-F2FS
CWM_touch_6.0.4.7_i9305
Attempts to flash these failed in the exact same way as the stock images did (as described above).
Despite all my (failed) flashing attempts, all symptoms remained unchanged (boot loops, no recovery, only download mode and charge mode working).
Questions
I'd really appreciate any tips, advice, or answers to the following questions:
Are these symptoms indicating a problem with the eMMC chip?
Is there any possible repair other than replacing the eMMC chip? Is there any chance for repair using a dedicated JTAG/eMMC tool?
Am I supposed to be able to salvage at least part of the data on the eMMC chip using an SD reader and an SD adapter soldered to the motherboard (e.g. in a manner similar to the process described here)?
Am I supposed to be able to salvage at least part of the data on the eMMC chip using a dedicated JTAG/eMMC tool? Would I be able to extract more data with such a tool than I would be able to extract using the soldered SD adapter and reader?
Many thanks in advance for your time and help efforts!
EMMC Brickbug claims another i930x device. Unfortunately, all the partitions after a certain area are useless because some defects in a batch of EMMCs. i9300 has had it for some time, but i didn't know that i9305 could have a part of the faulty lot that kneeled the i9300. You may be lucky enough, depending in what country you live, to find and go to a very good smartphone repair shop and get the EMMC replaced by some people that actually know what they are doing. Or, if you have money, skills and time to spare, replace it yourself, but you'd need to take some precautions to not f it up. (i.e. place some thick metal piece over the modem to not heat it up, and to not apply too much temperature to the board to damage it.)