Greetings!
I have ASUS MeMO 10 that I'm trying to do a factory hard reset.
When I get into recovery screen I only see the horizontal Android robot with an exclamation mark and the phrase "No Command" beneath it :crying:
What else can I do to bring this back into this world?
Thanks in advance!
Thank you. It was a little oddity after that no command picture. Fiddling (pressing) the power switch right after going into recovery brought the expected menu up. Had to try more than dozen times but finally worked!
Related
Sorry, wrong forum.
Can a mod please delete this
Hi all,
I have had loads of problems with this phone, so I decided to do a factory reset.
It rebooted as normal until it got to the Motoblur setup page
It asks for the Motoblur details to be entered, but once you have entered them and pressed the 'next' button, it goes back to the previous screen instead of the next step and then gets stuck in a never ending loop.
I've tried skipping the sign in process but instead of skipping it, it just goes back to the first Motoblur account setup screen instead.
Out of desperation, I have tried to make several new Motoblur accounts but every single time, it gets to 80% completion, then stops.
I have even left running all night (plugged in) and it still freezes at 80%
I can't do another factory reset because it won't get past the Motoblur setup screen.
I've tried to do a hard reset by holding x and powering the phone on but this doesn't work. It just brings up the triangle and android robot but it does not go to the next step despite me leaving it for several minutes.
Only had it for 7 weeks and am awaiting a response from Expansys on what to do.
Any help from you guys will be greatly appreciated.
phorenzik said:
I've tried to do a hard reset by holding x and powering the phone on but this doesn't work. It just brings up the triangle and android robot but it does not go to the next step despite me leaving it for several minutes.
Only had it for 7 weeks and am awaiting a response from Expansys on what to do.
Any help from you guys will be greatly appreciated.
Click to expand...
Click to collapse
I dont know how this is on milestone 2, but on milestone 1 after you press x+power button and the ! mark shows up you have to press "volume up+camera button" and it goes to recovery menu. There you do a factory reset and/or restore nandroid backups.
Or you can just flash a milestone 2 sbf from here "http://and-developers.com/sbf:milestone2" through RSDlite
It seems you are not familiar with all this happening to your phone. I suggest on starting reading threads about how it should be done and I'm sure you can bring your phone back to life.
Hope i've helped
Details:
moto x purchased from web site, for use on Tmobile
i'm currently deployed. Lucky enough to have WiFi on base and T-mobile so communication home this deployment has been amazing. Saw lollipop came out today. downloaded it. installed it. phone boots up with the regular "TOMMYBOT Mobile" and then the spinning M worlds. then it gives me the password (for the decryption). it took a min and then said some error about corrupt files and that i needed to factory reset my phone. so i pressed the button and nothing happened... so i powered down the phone. and then everything started up the same. but when i put in my password to decrypt it takes a minute and then says starting android.... and then the screen goes black. tried 5 times. longest i waited was 30min. (left it over night now, so 6 ish hours)
i can start my phone pressing the power and volum down and it brings up a fastboot menu? but even from there the factory reset option just boots my phone back up as if i pressed the power button.
any help is appriciated.
thank you,
tom
Edit: followed these instructions (cant link, motorola global portal)
and a matching youtube video and i get stuck at the dead android with the triangle "!" sign mine says "No command." under him and i cant get the next menu to open
asked for help here (link motorola forums help) they suggested verizon assistant app. the program
i've treid 3 times now. each time the start repair makes a command "getvar all" come up on the bottom half of my fast boot screen. and then thats where it stays. the "Repair" button on the right does not become clickable.
Solution:
once on the dead android screen to open the next menu it was press and hold volume up AND power for 3-5 seconds together .
from there i did the data wipe/factory reset and booting up i'm already on lollipop. of course all un clouded data lost but i'm just glad to have a phone again.
I wanted to wipe my cache but I can't get into recovery mode.
I can get into the bootloader and when I select Recovery Mode, all I get in the bugdroid on its back woith a red exclamation triangle and the word Error underneath.
Any ideas?
I'm having the same issue. I cannot figure out how to fix it. Any help would be appreciated!
I've just had the same issue on my daughter's ME176CX. For me, doing a short press of power and Volume + at the same time on the Error screen, allowed me to go in to the normal recovery menu.
Good luck!
RufusA said:
I've just had the same issue on my daughter's ME176CX. For me, doing a short press of power and Volume + at the same time on the Error screen, allowed me to go in to the normal recovery menu.
Good luck!
Click to expand...
Click to collapse
Thank you. That worked for me too.
RufusA said:
I've just had the same issue on my daughter's ME176CX. For me, doing a short press of power and Volume + at the same time on the Error screen, allowed me to go in to the normal recovery menu.
Good luck!
Click to expand...
Click to collapse
:good: Bravo, almost desperate, I thought I lost device Works on Asus Memo Pad ME302KL Thank you.
Maaaaaaaaaaaaaaaan.... This is my son's Tab and i thought it is brick and done for...... and there you are as angel from heaven.....
it's really amazing how people really seem to forget where the write places to search for solutions are... thinking that only youtube gives the cake...
but I say,, If youtube gives the Cake,, Forums Make The Precipices...
Thank You Man...
What do you mean by short press? The error signal is still there for me.
all im getting on this is to enter a password,cant reset or anything else ive tried..any ideas please
My Device ASUS K013 ME176C was working with: Vol+ and Vol- Buttons only same time a short press (less a sec). Try again if not working on first attempt.
The recovery mode with further menu now on the top.
Hi all. I have this old Touchpad that's been sitting in a drawer for years now. I shelved it because I could no longer boot android on it. It would hang with the android logo and stay that way till the battery died. I opened it today to take a look at resetting it because I want to get it going again. I discovered a little button on the board that resets the touchpad. Now I don't have to wait till the battery dies to try something different.
I can get it to boot to moboot 0.3.8 from there I can move the selection thing up and down to select a different boot choice but I don't know what to press to get it to boot that option. I thought it was the home button but that does not work. I would like to wipe it clean and start with a recent ROM that is solid and fast.
What's the first thing I need to do to get away from the moboot screen?
Jonathan
Ok I got past that by long-clicking the home button. Now i'm at the USB logo. I guess I can probably figure it out from here. Any pointers welcome though.
Hey guy. I have a problem with my watch. It is blinking the screen and I can't even enter settings. Only voice search works. I tried restarting it.
Is there a way I can reflash firmware without turning on adb ?
Here is a video showing the issue.
EDIT: I managed to enter recovery, but when I tap the green robot no options are available.
Wow! This just happened to my watch yesterday! I can't pull the video up, but my guess is it is the same thing - once it boots up, it just flashes on and off continuously. If I restart it, it just comes back up the same way. I cannot get into settings, I cannot connect to it from my phone, and I cannot perform a factory reset because the green Android in recovery mode has a red exclamation mark above him. It is completely dead.
And the best part - I am 37 days outside of the warranty period and LG wants to charge me to fix it. It is a $350 watch that barely lasted a year! Please, if anyone has any suggestions, please please please post here.
To fix it press top button + crown while in recovery. Wipe data/factory reset and reboot.
Im 99% sure it is caused by some update. Is your watch w280a too?
Thank you so much. Took a few tries of pressing top button and crown for my watch to boot into the reset option. Eventually got it right. Thank you so much. Saved me from a haveing a dumb expensive bracelet.