I have always used invisible shield on my devices. One reason was the wet application method their protectors use. I always have issues with dust, no matter what I do, but the application solution seems to rinse the dust out with it when you install the wrap. With a dry install if a single piece of dust lands on the screen on the install you're screwed.
Anyway, does anyone know if any of the Zagg (or other brand) protectors use a wet install?
Sent from my Note 5 via Tapatalk
Because I'm probably taking a dump.
Ghost armor does. Not sure why you would want one though.. way too much friction for something with a stylus.
Goronok said:
Ghost armor does. Not sure why you would want one though.. way too much friction for something with a stylus.
Click to expand...
Click to collapse
Would you say I'm ok without a screen protector then? I'm not one to throw my phone in my pocket with my keys or anything. I keep it in a pocket by itself. I would like one of the glass protectors but I've seen way too many bad things about them due to the screen being curved and causing a "halo" effect.
The "original" on their website I think. But that would be badddd with the pen.
Hezzennater said:
The "original" on their website I think. But that would be badddd with the pen.
Click to expand...
Click to collapse
I remember the original being pretty sticky feeling on my old iPhone. I just bought an HDX Defense, but it is a dry install as I referenced above. Its pretty clear and almost as smooth as glass, but I couldn't get it on without any dust. I ALMOST did but one big piece hit the screen just as I was laying it down, and I ruined the protector getting the dust off. I'll be sending in for replacement to try again but I just don't see how I could ever get one of these on without a single piece of dust. When I clean off my phone and watch if for about 5 seconds I get 10-15 little dust particle in that amount of time..... Ugh.
MrStig91 said:
I remember the original being pretty sticky feeling on my old iPhone. I just bought an HDX Defense, but it is a dry install as I referenced above. Its pretty clear and almost as smooth as glass, but I couldn't get it on without any dust. I ALMOST did but one big piece hit the screen just as I was laying it down, and I ruined the protector getting the dust off. I'll be sending in for replacement to try again but I just don't see how I could ever get one of these on without a single piece of dust. When I clean off my phone and watch if for about 5 seconds I get 10-15 little dust particle in that amount of time..... Ugh.
Click to expand...
Click to collapse
I do mine right in the bathroom after a shower. The steam helps keep the dust manageable. Also, use the tape hinge method so you can do it really fast after it's clean.
What is this tape hinge method? Also, I ran a ton of hot water in the bathroom to get the steam really going. It helped but I still got one piece of dust in there. =[ Probably took me about 15 seconds to apply, if I could do it in 3-4 seconds I could probably avoid all the dust.
I got the skinomi skin for my screen and its great. fits perfectly and no dust particles. it is not as smooth as glass or the plasticy screen protector, but I can do everything fine. prefer this over halos and dust around the halos.
MrStig91 said:
What is this tape hinge method? Also, I ran a ton of hot water in the bathroom to get the steam really going. It helped but I still got one piece of dust in there. =[ Probably took me about 15 seconds to apply, if I could do it in 3-4 seconds I could probably avoid all the dust.
Click to expand...
Click to collapse
It's popular for sticking decals on cars n such. Once you place the protector where you want it, make a hinge out of a piece of tape. Fold back the protector, peel off the backing, and use the hinge to put the protector back on in the same place it was taped. Here's a video.
I wouldn't mind having one for the glass back. It would add some nice grip.
Sent from my LG-H811 using Tapatalk
tbh if you just don't abuse the phone you should be fine without a protector. After reading an article about it back when I had a Galaxy S3, I peeled my Zagg protector off and didn't even use one on the Note 3. After 2 years of heavy daily use, the Note 3 looked nearly brand new - only a few extremely light small scratches viewable from certain angles with just the right lighting. I will definitely not be using anything on the Note 5 for that reason.
I have a desk job though, and am generally careful with everything i own, however. My step brother on the other hand... he delivers/installs large home appliances. In the last 3 years he utterly destroyed 2 Galaxy S4's and an iPhone 5 because he doesn't take care of his stuff at all (both S4's had smashed screens, camera lenses etc destroyed through a full Otterbox Defender case).
In any case - I too would strongly advise against a Zagg wet protector on a phone with a stylus. It would basically make the stylus unusable.
If i recall correctly, the reason they discontinued the wet application was people were applying it improperly and causing damage to their phones.
Basically they stopped selling them to cover their butts from lawsuits.
Related
Hey,
I just got got a Nexus S (upgrade from Nexus One w00t! ) and I'm really interested in getting a skin for it. I'm looking specifically at buying a Wrapsol one since I've read that it doesn't have the orange peel effect. I'm just confused over the "ultra protective film" (UPF) and the "original scratch protection" (OSP) that they're selling. I know that the UPF is a dry application and is $30 while the OSP is $25. I've put on many screen protectors in my life before but this is gonna be my first entry into the world of skins. What's the main difference between a dry and wet application protector? What is the better choice? Thanks for your help!
The only difference between wet and dry applicator is pretty much just the method of putting it on. Some people are not comfortable with spraying liquid on their phone so dry applications may appeal to them. The problem I see with this is that unless you are super pro like the guy in the video, you're going to have a frustrating time applying a dry protection on a curvy device like the nexus s. You pretty much have one shot at aligning everything. With a wet application, you can moisten the adhesive and actually slide the film around to align the curves perfectly and slowly work your way through.
I'm not sure about the difference in texture. I've seen some degree of orange peel in all wet applications with zagg being the worst. I'm not sure if wrapsol is orange peel free either due to the nature of the scratch resistant material used to make these film. I believe they use polyurethane.
Sent from my Nexus S using XDA App
I purchased a wrapsol protector for my s and honestly I regretted it the second I put it on. They said it stretches to fit the entire screen but it didn't and it doesn't have a hole for the front facing camera so images are blurry. I'm glad they have a 30 day money back return period cause this is going back as soon as my sgp protector comes.
peeturr said:
The only difference between wet and dry applicator is pretty much just the method of putting it on. Some people are not comfortable with spraying liquid on their phone so dry applications may appeal to them. The problem I see with this is that unless you are super pro like the guy in the video, you're going to have a frustrating time applying a dry protection on a curvy device like the nexus s. You pretty much have one shot at aligning everything. With a wet application, you can moisten the adhesive and actually slide the film around to align the curves perfectly and slowly work your way through.
I'm not sure about the difference in texture. I've seen some degree of orange peel in all wet applications with zagg being the worst. I'm not sure if wrapsol is orange peel free either due to the nature of the scratch resistant material used to make these film. I believe they use polyurethane.
Sent from my Nexus S using XDA App
Click to expand...
Click to collapse
Thanks for the insightful response! One of the things that has scared me away from things like Zagg and other wet application skins is the fact that after a couple of days, weeks, or months, the skin starts to peel off off the corners. Is that still a problem with skins today? (I saw the peeling off the corners a couple of years ago from my friends' blackberries.) Or is that more of the user's fault? I heard that you should ceram-wrap the devise completely also while it's drying so that everything sticks. Is that true? Is there an effective way of applying the skin so that they don't peel off by themselves off corners over time?
myboygino said:
I purchased a wrapsol protector for my s and honestly I regretted it the second I put it on. They said it stretches to fit the entire screen but it didn't and it doesn't have a hole for the front facing camera so images are blurry. I'm glad they have a 30 day money back return period cause this is going back as soon as my sgp protector comes.
Click to expand...
Click to collapse
Thanks for letting me know about the screen protector! I'm already planning on using a Clarivue screen protector. I'm more curious about the back and side protection itself. How were they? Did they have the orange peel effect? How did they feel like? Did you use the wet or dry one? How easy was it to apply? Lastly, did the skin ever start peeling off by itself?
Again, thanks for all of y'all's responses!
I personally use ghost armor and haven't experienced any peeling over a month now. The installation is crucial and patience is key. I wouldn't go so far as to ceram wrap the device. Just make sure you press on all edges and curves for 15 seconds or so once it begins to adhere to make sure it sticks permanently. Another tip is to lightly heat those areas with a hair dryer. It is very important that you keep your hands free, work in a lint free area, and let it dry for 24 hours. Don't put in your pocket for a day or two. The reason is because if dust accumulates on any part of the edge, it will lose adhesive there and make it prone to lifting or peeling. If you can get past the drying stage, then you shouldn't experience any peeling unless forced.
Sent from my Nexus S using XDA App
peeturr said:
I personally use ghost armor and haven't experienced any peeling over a month now. The installation is crucial and patience is key. I wouldn't go so far as to ceram wrap the device. Just make sure you press on all edges and curves for 15 seconds or so once it begins to adhere to make sure it sticks permanently. Another tip is to lightly heat those areas with a hair dryer. It is very important that you keep your hands free, work in a lint free area, and let it dry for 24 hours. Don't put in your pocket for a day or two. The reason is because if dust accumulates on any part of the edge, it will lose adhesive there and make it prone to lifting or peeling. If you can get past the drying stage, then you shouldn't experience any peeling unless forced.
Sent from my Nexus S using XDA App
Click to expand...
Click to collapse
Thanks! I'll definitely do what you suggested!
Well, I ended up ordering the Wrapsol wet application one. I'm just going to be using the back and side protection. I hope this goes well....
I've done both on 2 nexus S I own, I bought wrapsol because I could apply it dry.
However, after my experience with the 1st "dry" application I applied the second on "wet" why? because the end result is much smoother and less detectable.
btw if you are wondering why I need 2 Nexus S'es, one for me and one for the wife.
jdm_cars said:
I've done both on 2 nexus S I own, I bought wrapsol because I could apply it dry.
However, after my experience with the 1st "dry" application I applied the second on "wet" why? because the end result is much smoother and less detectable.
btw if you are wondering why I need 2 Nexus S'es, one for me and one for the wife.
Click to expand...
Click to collapse
Cool, thanks for letting me know! I heard that the wet one is a matte finish. Is that true? Also, what did you think of the screen protector portion of the wet skin?
I actually wet the ultra protective film version, its glossy not matte. Its very thick compared to the Zagg Ive used in the past, someone said it was made of polyurethane.
so far so good I like the way it looks on the screen portion with a lot less orange peel than the Zagg.
Ok am really! careful with my screen! but some how i have some little hair line Scratches! on my screen.. is there any way i can remove them safe? cheers
Should've put a screen protector immediately when you got it.
Sent from my SGH-I717M using xda premium
you may find adding a protector now will hide the scratches if they are small enough
They may be superficial. Did you try some good rubbing with a lint free cloth. I had no sp for the longest with no scratches
Sent from my GT-N7000 using XDA App
crackster said:
Ok am really! careful with my screen! but some how i have some little hair line Scratches! on my screen.. is there any way i can remove them safe? cheers
Click to expand...
Click to collapse
sadly NO, If it makes you feel any better my Note always has a case on and just once i removed it for 5 minutes, I manage to drop the phone on a concrete now my screen is scratched thank good the glass didn't break.
I have a scratch on my Galaxy Note also :/ I've only just had it for a week. I only noticed the scratch when I was about to put the screen protector on. I think it happened due to me showing my sister my phone, and she gave my phone to my TWO year old niece to draw on :/ I'm so upset and angry about it. I've dropped my HTC Desire HD many times and not a single scratch.
Moved To Q&A
Please post all questions in the Q&A section
I have a tiny little scratch on my note as well. Its no big deal because it can't be seen unless you direct it to the light at a certain angle but it still bugs me.
It seems like the scratch was made with the s pen as it has the pattern of something I had drawn when I was trying out the s pen.
I'll be getting a screen film soon to avoid any further scratches.
Sent from my GT-N7000 using Tapatalk
I got a 1mm deep scratch on my screen to
again always had a cover on it and when i took the cover off ... guess what .. it fell on its face and got the scratch.
Now i have the flip cover on it and wouldn't risk taking it off again.
As they mention : Gorilla grass is scratch resistant only.
Look up 'Displex' - it's the best scratch remover there is, and it's cheap too.
Sent from my GT-N7000 using xda premium
This isn't for the faint of heart....
I built scale plastic model airplanes for 30+ years until the bifocals & carpel tunnel made it impossible to hold an airbrush.
The clear plastic "glass" parts, if not packaged in a bag, can get scratched, screwing up a good looking model.
For starters, try some mild toothpaste. DO NOT rub very hard. It's glass, but you don't want to really screw it up...just in case. After toothpaste, try buffing it with a sheep skin cloth (chamois). Now this one will sound silly, but it works on plastic, clear future floor wax. I used it from time to time to fill the spider cracks where they didn't get the mold clean when they injected the plastic.
I haven't had to fix a gorilla glass/hardened glass screen, but I've used these tricks on my old windows phones & pda's after too many uses of the stylus.
I don't use a protector on either my streak, for over a year, or my note for the last 3 months. I don't understand how they are getting scratched.
p51d007 said:
This isn't for the faint of heart....
I built scale plastic model airplanes for 30+ years until the bifocals & carpel tunnel made it impossible to hold an airbrush.
The clear plastic "glass" parts, if not packaged in a bag, can get scratched, screwing up a good looking model.
For starters, try some mild toothpaste. DO NOT rub very hard. It's glass, but you don't want to really screw it up...just in case. After toothpaste, try buffing it with a sheep skin cloth (chamois). Now this one will sound silly, but it works on plastic, clear future floor wax. I used it from time to time to fill the spider cracks where they didn't get the mold clean when they injected the plastic.
I haven't had to fix a gorilla glass/hardened glass screen, but I've used these tricks on my old windows phones & pda's after too many uses of the stylus.
I don't use a protector on either my streak, for over a year, or my note for the last 3 months. I don't understand how they are getting scratched.
Click to expand...
Click to collapse
+1
Clear floor polish works on harder clear plastic. Never tried on glass. WOrth trying for $10 from local supermarket. And then put a cover on it
I'm lucky so far - only scratches have been on the screen protectors. But then I need to replace them - used up two so far, and good quality 6H ones too! Better than a scratched glass though - sorry to hear about that!
I never usually buy screen protectors for my devices, but since I'll be using this phone for a full two years, I think I should try to prevent as many scratches as possible. Can anyone recommend a good brand of screen protectors? I saw that Motorola makes an official one but it's $15.
I would like to know too didn't see any good ones out yet. I had spiegen for s4 and used indivisible shield before.
Sent from my XT1060 using Tapatalk 4
I too like to use a name brand screen protector like Spigen. I went with the Verizon brand ones off of a recommendation from someone. 3 for $12, they're decent enough as a stopgap until bigger companies put theirs out. Of course, since Moto X is the same for all carriers, you can still order them even if not Verizon.
Halo. Look them up on Amazon. Feels just like glass
had invisashield but its cut horribly, testing the skinomi so far so good cheap/effective/cut perfectly
Sent from my XT1058 using XDA Premium 4 mobile app
Grabbed the Skinomi (at...1 cent? + shipping it was a no brainer!) but seems to pick up pocket lint (after having been on for 24 hours+), which is a problem I've never had before with any other screen protector. Also has some...I don't want to say bubbles, because they're not, but..ripples? ... near the bottom, which are noticeable when the screen is off. That said, the touch is just fine and besides those little issues at the bottom, it looks decent.
Have a few others to try that'll by here early next week.
I am waiting to find a tempered glass protector, I like how much more original it feels plus its much stronger than a sheet of plastic
Ordered the i-blason screen protectors and they should be in tomorrow, I'll give my take on em once I get them.
http://www.amazon.com/gp/aw/d/B00E0...040_30332190_pe_175190_21431760_M3T1_ST1_dp_1
Ordered and received my Halo protectors from Amazon. They are awful, I wouldn't recommend them to anyone. The cut was terrible, and none of the 3 worked out. They felt like they were almost too long as well, having lift at either the top or bottom without a way to make it go away. Gonna get some from VZW as I hear they are good.
I only use halo. Mine is cut and fits perfect. Clarity is good and its feels just like the glass does
Just got my I-Blason screen protectors in. Took me all 3 just to get one without bubbles but the screen protector feels good and is very clear. Cut is a little small though so you gotta perfectly center the screen protector. Also for the top where the speaker and front camera is they just cut out a whole section instead of just the holes for the two.
I don't like wet installs (Zagg, and I think Skinomi is one too). I've used them in the past and have always encountered streaks despite drying, cloudy screens, or the dreaded orange peel (looking at you, Zagg).
I much prefer dry installs. The Verizon protectors are actually really good, surprisingly. Just turn on the hot shower for a few minutes, let it steam up, then install. Quite easy. The screen isn't clouded at all and still feels smooth as glass.
I love my Zagg HD. When/if they come out with a Zagg Extreme I will be buying one of those.
Sent from my XT1060 using xda app-developers app
Any tempered glass yet ?
Sent from my Moto X
Yazzinit said:
I don't like wet installs (Zagg, and I think Skinomi is one too). I've used them in the past and have always encountered streaks despite drying, cloudy screens, or the dreaded orange peel (looking at you, Zagg).
I much prefer dry installs. The Verizon protectors are actually really good, surprisingly. Just turn on the hot shower for a few minutes, let it steam up, then install. Quite easy. The screen isn't clouded at all and still feels smooth as glass.
Click to expand...
Click to collapse
I have never heard of this "hot shower steam up" method. Can anyone elaborate on why I would do that?
thepolishguy said:
I have never heard of this "hot shower steam up" method. Can anyone elaborate on why I would do that?
Click to expand...
Click to collapse
Sure. Have you ever personally tried installing a dry protector say, in your room and you keep getting a few specs of dust under it? Well if you haven't, that's what happens lol. Really annoying, you get the protector down and that 1 spec flies in and you didn't see it, now you have to remove the film and try again, and some are impossible to get the dust off of the sticky side.
In the shower, you run a hot shower 10 minutes, then turn it off. Leave the door open just a small crack. Apparently, the steam causes the dust to rise with it, or fall, whatever the science is lol. Makes for no dust in the air to fall on your screen and allows for installing a dry protector really easy. Wipe with a microfiber cloth and install right there.
Yazzinit said:
Sure. Have you ever personally tried installing a dry protector say, in your room and you keep getting a few specs of dust under it? Well if you haven't, that's what happens lol. Really annoying, you get the protector down and that 1 spec flies in and you didn't see it, now you have to remove the film and try again, and some are impossible to get the dust off of the sticky side.
In the shower, you run a hot shower 10 minutes, then turn it off. Leave the door open just a small crack. Apparently, the steam causes the dust to rise with it, or fall, whatever the science is lol. Makes for no dust in the air to fall on your screen and allows for installing a dry protector really easy. Wipe with a microfiber cloth and install right there.
Click to expand...
Click to collapse
Wow! I definitely will try this next time bc I always get dust under mine. Thanks.
Yazzinit said:
Sure. Have you ever personally tried installing a dry protector say, in your room and you keep getting a few specs of dust under it? Well if you haven't, that's what happens lol. Really annoying, you get the protector down and that 1 spec flies in and you didn't see it, now you have to remove the film and try again, and some are impossible to get the dust off of the sticky side.
In the shower, you run a hot shower 10 minutes, then turn it off. Leave the door open just a small crack. Apparently, the steam causes the dust to rise with it, or fall, whatever the science is lol. Makes for no dust in the air to fall on your screen and allows for installing a dry protector really easy. Wipe with a microfiber cloth and install right there.
Click to expand...
Click to collapse
Just to clarify: Do not actually have your phone in the shower, just in the room with the shower.
Anyone had any experience with either of these two screen protector brands?
http://www.amazon.com/gp/product/B00E5QKHOY/ref=ox_sc_act_title_2?ie=UTF8&psc=1&smid=A3LQSX85N730QN
http://www.amazon.com/IQ-Shield-LIQ...7061&sr=8-13&keywords=moto+x+screen+protector
I just ordered a pack of five from amazon. Were cheap but I'm sure I'll get at least one that works. I have tried Zagg and Armor Suit and hated them both. Went naked for awhile on my S3 and just had one tiny scratch. I work around metal and grinding dust all day and only had that one scratch. Never put one on my S4 but only had it a few days. If you have to keep the phone for two years, then a screen protector maybe good for a while IMO.
Sent from my Moto X
FesterTOR said:
I just ordered a pack of five from amazon. Were cheap but I'm sure I'll get at least one that works. I have tried Zagg and Armor Suit and hated them both. Went naked for awhile on my S3 and just had one tiny scratch. I work around metal and grinding dust all day and only had that one scratch. Never put one on my S4 but only had it a few days. If you have to keep the phone for two years, then a screen protector maybe good for a while IMO.
Sent from my Moto X
Click to expand...
Click to collapse
What did you hate about Zagg and Armor Suit?
When it comes to expensive new technology I tend to obsess over the tiniest imperfection. The miniscule hairline scratch on an otherwise flawless screen. That single piece of dust that always manages to get under your screen protector despite using a hazmat clean room to install it. That little nick on the metal edge. All of this drives me nuts. Once it's there my shiny new tablet is no longer pristine and perfect. It's like the first ding on your new BMW. After that it just isn't the same.
Well today I traded my new white 10.5 book cover, which was flawless except that I decided I didn't like white for a case, for a new titanium cover. Now I'm one of these guys that can choose from 10 cases and I'll ALWAYS pick the one with the defect. I never fails. Anyway loving the case, get it home and put it on. Only then do I notice that there is the equivalent of a screen protector dust particle trapped under the skin on the front. One tiny little raised dot in the middle of an otherwise perfect case. Sigh, and now I must obsess. I will endure it for a day or two then finally return it for a PERFECT one. I know me. Probably why BestBuy has wanted posters of me on their front door .
Why do I even care? Anyone else like this?
mitchellvii said:
When it comes to expensive new technology I tend to obsess over the tiniest imperfection. The miniscule hairline scratch on an otherwise flawless screen. That single piece of dust that always manages to get under your screen protector despite using a hazmat clean room to install it. That little nick on the metal edge. All of this drives me nuts. Once it's there my shiny new tablet is no longer pristine and perfect. It's like the first ding on your new BMW. After that it just isn't the same.
Well today I traded my new white 10.5 book cover, which was flawless except that I decided I didn't like white for a case, for a new titanium cover. Now I'm one of these guys that can choose from 10 cases and I'll ALWAYS pick the one with the defect. I never fails. Anyway loving the case, get it home and put it on. Only then do I notice that there is the equivalent of a screen protector dust particle trapped under the skin on the front. One tiny little raised dot in the middle of an otherwise perfect case. Sigh, and now I must obsess. I will endure it for a day or two then finally return it for a PERFECT one. I know me. Probably why BestBuy has wanted posters of me on their front door .
Why do I even care? Anyone else like this?
Click to expand...
Click to collapse
My poster at BB is for always looking out for returns so I can get something I want cheaper. They are ready to crown me "king". So long as what was returned is in more than acceptable shape and does not deter from the product's use, why not.
BTW, which BB are you returning it to?
mitchellvii said:
When it comes to expensive new technology I tend to obsess over the tiniest imperfection. The miniscule hairline scratch on an otherwise flawless screen. That single piece of dust that always manages to get under your screen protector despite using a hazmat clean room to install it. That little nick on the metal edge. All of this drives me nuts. Once it's there my shiny new tablet is no longer pristine and perfect. It's like the first ding on your new BMW. After that it just isn't the same.
Well today I traded my new white 10.5 book cover, which was flawless except that I decided I didn't like white for a case, for a new titanium cover. Now I'm one of these guys that can choose from 10 cases and I'll ALWAYS pick the one with the defect. I never fails. Anyway loving the case, get it home and put it on. Only then do I notice that there is the equivalent of a screen protector dust particle trapped under the skin on the front. One tiny little raised dot in the middle of an otherwise perfect case. Sigh, and now I must obsess. I will endure it for a day or two then finally return it for a PERFECT one. I know me. Probably why BestBuy has wanted posters of me on their front door .
Why do I even care? Anyone else like this?
Click to expand...
Click to collapse
All they had was a white one at my store. Youre lucky they had the other colors.
LOL I am not even going to look for imperfections in mine now. I'm afraid I would obsess over it too.
Sent from my SM-T700 using XDA Free mobile app
haha this level of obsession reminds me of my x-men comic collection back in high school and it was costly for someone who has to keep within his allowance
I spent a good hour applying my screen protector. I cannot accept any dust, bubbles, etc. I think the prep time takes longer that the actual preparation. I turn the shower on full hot and steam up the bathroom. After its good and foggy in there I turn the water off and close the door. The steam seems to take the dust out of the air. After about 15 minutes, I will go in and carefully apply the protector. There is good lighting in there so I can see anything that gets trapped under the protector. Works pretty well for me as I no longer go through several protectors trying to get it just right. I do obsess over the smallest imperfection. Call it OCD, being anal, or whatever. I just can't enjoy something as well if I know there's a flaw. Having said that, I absolutely happy with my titanium Tab S 10.5 and book cover so far. :fingers-crossed:
rsfinsrq said:
I spent a good hour applying my screen protector. I cannot accept any dust, bubbles, etc. I think the prep time takes longer that the actual preparation. I turn the shower on full hot and steam up the bathroom. After its good and foggy in there I turn the water off and close the door. The steam seems to take the dust out of the air. After about 15 minutes, I will go in and carefully apply the protector. There is good lighting in there so I can see anything that gets trapped under the protector. Works pretty well for me as I no longer go through several protectors trying to get it just right. I do obsess over the smallest imperfection. Call it OCD, being anal, or whatever. I just can't enjoy something as well if I know there's a flaw. Having said that, I absolutely happy with my titanium Tab S 10.5 and book cover so far. :fingers-crossed:
Click to expand...
Click to collapse
Best way to apply a screen protector to a large device is by placing the protector on the screen in the proper position then apply a strip of masking tape to the left edge attaching it to the tablet. Then once all dust is cleared, lift the protector up and peel away the backing as you let the hinge hold it steady. Watch for any little dust particle as you slowly apply the protector and use another piece of tape to remove them. Once applied just remove the tape hinge. Perfect placement, no dust .
who's using them? i horribly failed at putting one on today (a free one that came with my case..looked crappy though with tons of bubbles between the 3 layers before i even put it on lol) but yeah, i'm real bad at putting protectors on tablets because it kept coming out crooked because of that damn home button etc.
anyway, i've got a pack of 5 coming in the mail sometime this week, and i'm wondering if i should even bother attempting again, or just use it naked. it feels so good without a protector, but i'm afraid of scratching the screen. i've been using screen protectors since 2011 with my HTC Rezound, so idk what to do. i always end up with tiny scratches on my protectors, so i'm thinking i'll end up scratching the screen..
jayochs said:
who's using them? i horribly failed at putting one on today (a free one that came with my case..looked crappy though with tons of bubbles between the 3 layers before i even put it on lol) but yeah, i'm real bad at putting protectors on tablets because it kept coming out crooked because of that damn home button etc.
anyway, i've got a pack of 5 coming in the mail sometime this week, and i'm wondering if i should even bother attempting again, or just use it naked. it feels so good without a protector, but i'm afraid of scratching the screen. i've been using screen protectors since 2011 with my HTC Rezound, so idk what to do. i always end up with tiny scratches on my protectors, so i'm thinking i'll end up scratching the screen..
Click to expand...
Click to collapse
I was thinking about picking up some myself. Which ones did you order?
Put one on but spend at least 10 bucks for a decent one. Illunisheild thats the one I got from amazon for the 8.4 its pretty good.
I got these:
http://www.ebay.com/itm/161361388722?_trksid=p2060778.m2749.l2649&ssPageName=STRK:MEBIDX:IT
Sent from my SM-T700 using Tapatalk
I always put screen protectors on all of my phones and tablets. I've just put one on my Tab S 8.4, had a few dusts under the protector. usually I would rip it out and try again, but I thought not today! Because fortunately the screen protector came with some stickers to help get rid of the dust.
Happy to say it is dust and bubble free now. Although it is not one of those fancy screen protectors, just a cheap one called elec shield.
invisible shield is the best.
will6316 said:
Put one on but spend at least 10 bucks for a decent one. Illunisheild thats the one I got from amazon for the 8.4 its pretty good.
Click to expand...
Click to collapse
I ordered these from Amazon as well. Should be in today.
I'll give it a try and see if I like it. Probably gonna feel weird at first though.
I too would like to buy one. I asked ismooth on twitter but they are not gonna make one for the tab S (I have one for my note 3 and it's just perfect).
I think I'm gonna go Invisibleshield. It's not cheap but I've only heard good things about their products :good:
anyone have any tricks as to how to get it on nice and straight on the tablets? I'm bad at tablets for protectors but decent at phones. I saw one idea where you place it down on the screen then tape the sides like a hinge, then you flip it over, peel it off, and just flip it back and lay it on the tablet and it should line up perfectly. wonder if it works.
Sent from my VS980 4G using Tapatalk
jayochs said:
anyone have any tricks as to how to get it on nice and straight on the tablets? I'm bad at tablets for protectors but decent at phones. I saw one idea where you place it down on the screen then tape the sides like a hinge, then you flip it over, peel it off, and just flip it back and lay it on the tablet and it should line up perfectly. wonder if it works.
Sent from my VS980 4G using Tapatalk
Click to expand...
Click to collapse
That's exactly what I did. Works perfectly. The screen protector I bought even came with the positioning tape and stickers for dust removal. But you can just use Scotch tapes.
Mr shield
I have used many different screen protector products. I like spigen and I just installed the Mr shield ones. The are two finishes. Clear and matte. The matte finish cuts a lot of glare but impacts out door viewing. I now have the clear and love it. No bubbles. I have several videos on screen protectors that show tips on install . Herr is my initial install http://youtu.be/NHzarYjTtzE
kliu888 said:
That's exactly what I did. Works perfectly. The screen protector I bought even came with the positioning tape and stickers for dust removal. But you can just use Scotch tapes.
Click to expand...
Click to collapse
sweet! i'll give it a try when they come in
Putting on a screen protector reminds one of what a dirty filthy planet we live on. There is dust EVERYWHERE. One tried and true method is to run a hot shower in your bathroom for 10 minutes with the door closed until the room steams up. This pulls all of the airborne dust from the air. Turn the shower off, and use the tape hinge method to apply the protector.
Despite your best efforts you are likely to STILL get that ONE DAMNED PIECE OF DUST FROM HELL that manages to somehow get on the screen. If that happens, DO NOT TRY TO PEEL THE PROTECTOR UP FROM THE EDGE because if you bend it at all it will never seat again properly and you'll have a bubble that won't go away. Use tape to stick to the outside near the corner and gently lift that way, then use another piece of tape to grab the dust particle.
One negative of putting a screen protector on a tablet this size. Unless the protector is tempered glass, you are likely to feel a bit of drag as you swipe the screen - no plastic will ever feel as smooth as glass - and because the area is larger than your phone, you'll notice the resistance more. Also, unless the screen protector has an oleophobic coating, it will be harder to clean greasy fingerprints of it than from glass. Last point, most screen protectors are actually softer than glass so you are likely to get it pretty scratched up which, while saving your glass, leaves you with a scratched up viewing surface you have to look at. The alternative is to buy a screen protector with a hardness of 9 or above with an oleophobic coating but those tend to be a lot more expensive.
Get a pack of 3 or more if you can. You WILL screw it up a few times and you WILL want to replace them occasionally as they get scratched up pretty easily depending upon how anal you are about such things.
good advice, thanks! but do you guys think this thing needs one in the end? I know gorilla glass is pretty soft and scratches easily so idk..
Sent from my SM-T700 using Tapatalk
jayochs said:
good advice, thanks! but do you guys think this thing needs one in the end? I know gorilla glass is pretty soft and scratches easily so idk..
Sent from my SM-T700 using Tapatalk
Click to expand...
Click to collapse
I don't believe this tablet has Gorilla Glass, at least I don't believe the specs say so (could be wrong?). So yes, it could scratch easily. You can try and be careful but all takes is a tiny bit of grit on your finger, stylus or wiping cloth and you are done, Gorilla Glass or no.
Actually you know, skip the steamy bathroom. Just do it in a dry room but use a strip of masking tape and screen until every bit of dust is gone. Also remember, after you place the protector on the screen with the taped hinge, make sure you clean the screen again because it will get dust on it from the bottom of the protector.
Mr Shield makes very good inexpensive protectors.
http://www.amazon.com/gp/product/B00KATOH2S/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1
perfect install on first one using the painters tape technique.
heres how
https://www.youtube.com/watch?v=PMPqDwVZzzM
Why put a cheap screen protector on a premium device like the tab s. The best deserves the best or better. my screen protector cost 2 for 13 and a tempered glass on is on its way for $18. You cant even tell there on when installed correct.
will6316 said:
Why put a cheap screen protector on a premium device like the tab s. The best deserves the best or better. my screen protector cost 2 for 13 and a tempered glass on is on its way for $18. You cant even tell there on when installed correct.
Click to expand...
Click to collapse
Be very careful with the tempered glass protector. NEVER left it up by the edges - use tape. They bend VERY easily and once bent will never lay down flat properly again. Every tempered glass protector I've ever used developed sealing problems along the edges, especially near the home button. YMMV but that is my experience.
There aren't good selection of screen protectors in the UK. Looked in Amazon, Ebay, Google, nothing with quality. So I only got the Elec shield.
I'd get tempered glass if I could, but as long as I screen is protected for now, then I'm happy enough.