Related
My i9305 LTE is caught in a boot loop (just loops the start-up screen of any ROM I install). I have access to CWM recovery v6.0.4.5 and also download recovery.
The only thing I can think that might have caused this was when I installed Archidroid I (foolishly?) selected the only partition that wasn't ext4, to be set as ext4. It's not booted past any of the bootscreens on any ROM since I did this.
I've tried wiping all data and cache and also doing a data/factory reset and every "clear data" option available and I'm still caught in a boot screen loop on any ROM I try.
I've formatted each of the folders on the device by mounting and formatting (I don't need to keep any data on the phone) and then to get a new ROM on the phone I've inserted an SD Card, mounted it in CWM recovery and installed it from the .zip that way, all ROMs I've tried just lock up at their boot screen, it just loops over and over.
I've searched this forum and on Google but cannot find a solution or anyone with a similar issue, most that have had a similar looping problem say they performed an Odin factory reset, which brings me to my next question.
I don't know the region of my phone as I cannot access the dialler or any of my settings to find out the region, and forgot (as I rooted so long ago). I do have on the back of the phone the codes:
FCC ID: A3LGI9305
SSN: -I9305GSMH
as well as my IMEI #
How do I know my phone region, and which firmware/rom would I use to perform a full factory reset to at least get it booting again?
Any tips/ideas please, that would be much appreciated.
likeasir said:
My i9305 LTE is caught in a boot loop (just loops the start-up screen of any ROM I install). I have access to CWM recovery v6.0.4.5 and also download recovery.
The only thing I can think that might have caused this was when I installed Archidroid I (foolishly?) selected the only partition that wasn't ext4, to be set as ext4. It's not booted past any of the bootscreens on any ROM since I did this.
I've tried wiping all data and cache and also doing a data/factory reset and every "clear data" option available and I'm still caught in a boot screen loop on any ROM I try.
I've formatted each of the folders on the device by mounting and formatting (I don't need to keep any data on the phone) and then to get a new ROM on the phone I've inserted an SD Card, mounted it in CWM recovery and installed it from the .zip that way, all ROMs I've tried just lock up at their boot screen, it just loops over and over.
I've searched this forum and on Google but cannot find a solution or anyone with a similar issue, most that have had a similar looping problem say they performed an Odin factory reset, which brings me to my next question.
I don't know the region of my phone as I cannot access the dialler or any of my settings to find out the region, and forgot (as I rooted so long ago). I do have on the back of the phone the codes:
FCC ID: A3LGI9305
SSN: -I9305GSMH
as well as my IMEI #
How do I know my phone region, and which firmware/rom would I use to perform a full factory reset to at least get it booting again?
Any tips/ideas please, that would be much appreciated.
Click to expand...
Click to collapse
what country do you live? the region is the country you live in, just search for your official firmware on sammobile or samsung update site. and download the firmware for your country, flash it with odin.
also update your recovery to the latest available in your case cwm 6.0.4.7
PHP:
MaHo_66 said:
what country do you live? the region is the country you live in, just search for your official firmware on sammobile or samsung update site. and download the firmware for your country, flash it with odin.
also update your recovery to the latest available in your case cwm 6.0.4.7
Click to expand...
Click to collapse
I live in Australia but am slightly worried as I bought my phone from Koga online so it's an internationally shipped phone I think originally intended for the uk as it had a uk adaptor for the plug does this matter?
likeasir said:
PHP:
I live in Australia but am slightly worried as I bought my phone from Koga online so it's an internationally shipped phone I think originally intended for the uk as it had a uk adaptor for the plug does this matter?
Click to expand...
Click to collapse
Hmm... Good question. I understand your issue here but im afraid i cant answer this.. While it was working what firmware was running on it? What baseband? If you have any kind of info of the working firmware, analyze it with firmwares on those sites and try to find the one you need.
Sent from my GT-I9305 using XDA Premium 4 mobile app
likeasir said:
My i9305 LTE is caught in a boot loop (just loops the start-up screen of any ROM I install). I have access to CWM recovery v6.0.4.5 and also download recovery.
The only thing I can think that might have caused this was when I installed Archidroid I (foolishly?) selected the only partition that wasn't ext4, to be set as ext4. It's not booted past any of the bootscreens on any ROM since I did this.
I've tried wiping all data and cache and also doing a data/factory reset and every "clear data" option available and I'm still caught in a boot screen loop on any ROM I try.
I've formatted each of the folders on the device by mounting and formatting (I don't need to keep any data on the phone) and then to get a new ROM on the phone I've inserted an SD Card, mounted it in CWM recovery and installed it from the .zip that way, all ROMs I've tried just lock up at their boot screen, it just loops over and over.
I've searched this forum and on Google but cannot find a solution or anyone with a similar issue, most that have had a similar looping problem say they performed an Odin factory reset, which brings me to my next question.
I don't know the region of my phone as I cannot access the dialler or any of my settings to find out the region, and forgot (as I rooted so long ago). I do have on the back of the phone the codes:
FCC ID: A3LGI9305
SSN: -I9305GSMH
as well as my IMEI #
How do I know my phone region, and which firmware/rom would I use to perform a full factory reset to at least get it booting again?
Any tips/ideas please, that would be much appreciated.
Click to expand...
Click to collapse
Well I was in the same pickle
whicever 4.3 rom i flashed through odin i got stuck in boot logo or even if i recovered device from odin through emergency frimware and intillation
Also tried customs 4.3 roms stuck a boot logo
Here what u should try and what i did
1 flash philz recovery + 4.1.2 rom
if it works back up efs
2 Using Philz recovery wipe data factory reset + wipe cache + dalvik cache
3 in mount and storage section format everything ( THINK THIS IS THE MOST IMPORTANT STEP )
4 Used odin to flash a 4.3 stock package it worked ( note u may get knox from this u may try a modifed stock package if u dont have knox and dont want to get it )
AMoizK said:
Well I was in the same pickle
whicever 4.3 rom i flashed through odin i got stuck in boot logo or even if i recovered device from odin through emergency frimware and intillation
Also tried customs 4.3 roms stuck a boot logo
Here what u should try and what i did
1 flash philz recovery + 4.1.2 rom
if it works back up efs
2 Using Philz recovery wipe data factory reset + wipe cache + dalvik cache
3 in mount and storage section format everything ( THINK THIS IS THE MOST IMPORTANT STEP )
4 Used odin to flash a 4.3 stock package it worked ( note u may get knox from this u may try a modifed stock package if u dont have knox and dont want to get it )
Click to expand...
Click to collapse
Thanks for your suggestion, I'll give that a shot tonight. I'm able to get into CWM as explained, mount and format everything so I'm not sure that this step will make a difference, but I'll do it again anyway.
So I'll see how it goes tonight. Actually been quite refreshing without a phone these past couple of days
likeasir said:
Thanks for your suggestion, I'll give that a shot tonight. I'm able to get into CWM as explained, mount and format everything so I'm not sure that this step will make a difference, but I'll do it again anyway.
So I'll see how it goes tonight. Actually been quite refreshing without a phone these past couple of days
Click to expand...
Click to collapse
I managed to fix it, but it had me totally stumped for a while.
I flashed philz recovery and then formatted all of the directories as I'd done previously on CWM.
I tried Slim Rom which didn't work.
I ended up tying CyanogenMod stable which actually worked, it got past the boot loop phase! - I was glad to see a setup screen after 2 days!
I then had another issue with my Cell Reception not working, no data or reception would be shown.
This seemed to happen since I tried a KitKat ROM, as I remember before the bootloop it did this on a couple of ROMs I tried to manually enter the APN over and over and it wouldn't let me save it, very annoying.
I checked the baseband in the about phone section and it was being displayed as "unknown", luckily I remembered my baseband # from when I rooted the phone about 8 months ago (XXBLL3), then I found on this forum a list of 9305i baseband downloads as .zips so I was able to load up CWM and flash it, reboot and it worked!
I will be keeping with CM Stable (10.1.3) for a while now.
I hope this helps someone else that might run into a similar issue.
likeasir said:
I managed to fix it, but it had me totally stumped for a while.
I flashed philz recovery and then formatted all of the directories as I'd done previously on CWM.
I tried Slim Rom which didn't work.
I ended up tying CyanogenMod stable which actually worked, it got past the boot loop phase! - I was glad to see a setup screen after 2 days!
I then had another issue with my Cell Reception not working, no data or reception would be shown.
This seemed to happen since I tried a KitKat ROM, as I remember before the bootloop it did this on a couple of ROMs I tried to manually enter the APN over and over and it wouldn't let me save it, very annoying.
I checked the baseband in the about phone section and it was being displayed as "unknown", luckily I remembered my baseband # from when I rooted the phone about 8 months ago (XXBLL3), then I found on this forum a list of 9305i baseband downloads as .zips so I was able to load up CWM and flash it, reboot and it worked!
I will be keeping with CM Stable (10.1.3) for a while now.
I hope this helps someone else that might run into a similar issue.
Click to expand...
Click to collapse
Cheers on getting ur phone fixed but after wiping all directories a stock rom flash would have cleared all the problems
lol i just did this to my phone, time to find a stock firmware.
Hi everybody,
just got an old yet effective SGS and I wanted root and get rid of touchwizz and all the crap from my carrier
I was unable to boot into DL mode, i tried everything, so I had to do it with adb reboot
I never had to use Odin to do my hacking with android so i'm not used to it but short story : I rename my rom.zip into rom rom.tar, it failed and all I have is this now :
https://www.dropbox.com/s/wk42jbmp33a3ftu/IMG_20140715_152917.jpg
Also I need to unsimlock, flashing a new rom will also do the trick right ?
thanks
What you just did is bricking your phone. It it was a zip file you need to install it from the recovery. Renaming it is not the way it works. I'm not sure if now you can fix it. Sorry, man
Sent from my GT-I9000 using XDA Premium 4 mobile app
Do you know what I can at least try?
If you can get into download mode:
Follow sections 2 and 3 in this guide.
If you can't:
Follow this guide and after that do what I sails to do if you have download mode.
Does 3-button-combo not work to get into the download mode?
(power & home & volume down)
tetakpatalked from Nexus 7 flo
so i tried the resistance thing but i was unable to find all of the part required so i bought one of these already done solution thingy
It worked, I'm now able to boot into DL mode
I also succesfully install a random 2.x rom from an unknown european carrier, no root, lots of crap installed, and simlocked
How do i get from that to my CM 11 rom ? (this time it's in .tar format via 7zip ^^')
I tried via Odin in PDA it says fail right away
what can I do ?
thanks fr all the answers guys
@Idealith simlock has nothing to do with the firmware.
You need now any root kernel for that firmware, it has to be compatible with the intiframs of your 2.x version and it will give you a custom recovery.
There you can flash first CM10.2 to get the modified partition sizes and KK ready recovery and after that you can flash CM11
IMHO, the new Mackay ICS 2014 rom based on CM9 is a lot faster than any KitKat and works better on the i9000
tetakpatalked from N7100
my question about the rom still applies cause this one is awful
but with what does it have to do then ?
EDIT : my browser didn't render the end of your answer
I'm afraid i'm not following though :/
I got my 2.3 rom to stop crashing
and I once boot into recovery mod idk how ..
I selected the 10.2 CM rom but it started rebooting over and over again
I'm really not following everything that is happening over here :/
Idealith said:
I got my 2.3 rom to stop crashing
and I once boot into recovery mod idk how ..
I selected the 10.2 CM rom but it started rebooting over and over again
I'm really not following everything that is happening over here :/
Click to expand...
Click to collapse
Hey, could you tell me which country you are at? I could then take a few steps to help you
PFFFFFFFFFFFFFFFFTTT, sent from my i9000
I am currently in France
last news : been able to reboot into CWM, I selected the mackay cm 9 based rom, it rebooted halfway thrugh only to reboot in TWRP (idk how, are both installed or is twrp in the rom too ???)
so i tried from twrp wiping everything before and it wen through, then on bot it told me it needed to factory reset, it never worker though
so now i can boot into CWM but can't access my sd card ...
thanks
Idealith said:
I am currently in France
last news : been able to reboot into CWM, I selected the mackay cm 9 based rom, it rebooted halfway thrugh only to reboot in TWRP (idk how, are both installed or is twrp in the rom too ???)
so i tried from twrp wiping everything before and it wen through, then on bot it told me it needed to factory reset, it never worker though
so now i can boot into CWM but can't access my sd card ...
thanks
Click to expand...
Click to collapse
It was perfectly normal behavior, as after flashing the zip from CM, it will in firat step upgrade your recovery to TWRP 2.2.2.0
As you have wiped already before, it would be perfectly fine to just flash the rom.zip in the new TWRP recovery, and your gapps right afterwards. The recovery upgrade is totally common on the i9000 as first step.
The i9000 can easily be unbricked by flashing a stock image with Odin.
tetakpatalked from Nexus 7 flo
tetakpatak said:
It was perfectly normal behavior, as after flashing the zip from CM, it will in firat step upgrade your recovery to TWRP 2.2.2.0
As you have wiped already before, it would be perfectly fine to just flash the rom.zip in the new TWRP recovery, and your gapps right afterwards. The recovery upgrade is totally common on the i9000 as first step.
The i9000 can easily be unbricked by flashing a stock image with Odin.
tetakpatalked from Nexus 7 flo
Click to expand...
Click to collapse
I suppose my phone has been unbricked I made a 2.3 stock rom work
What i do now :
I flash the stock rom, go back to DL mode, flash the recovery, take the battery off, boot back in recovery, wipe everything ( do I really have to wipe system and all ?), select the ROM, nd once I'm in TWRP i reselect than same ROM
for the cm9 based mackay one it keep rebooting over and over again
for CM 10.2 it says the encryption failed and I need to factory reset, then nothing works
Idealith said:
I suppose my phone has been unbricked I made a 2.3 stock rom work
What i do now :
I flash the stock rom, go back to DL mode, flash the recovery, take the battery off, boot back in recovery, wipe everything ( do I really have to wipe system and all ?), select the ROM, nd once I'm in TWRP i reselect than same ROM
for the cm9 based mackay one it keep rebooting over and over again
for CM 10.2 it says the encryption failed and I need to factory reset, then nothing works
Click to expand...
Click to collapse
Yes, that would be correct procedure. To install CM9 you will have to format data, cache and dalvik cache.
If you have never had a JVU or JVZ firmware installed, it is likely that you still have a Froyo bootloader which could be reason of the problems with Android 4.xx
tetakpatalked from N7100
tetakpatak said:
Yes, that would be correct procedure. To install CM9 you will have to format data, cache and dalvik cache.
If you have never had a JVU or JVZ firmware installed, it is likely that you still have a Froyo bootloader which could be reason of the problems with Android 4.xx
tetakpatalked from N7100
Click to expand...
Click to collapse
and how do i get that bootloader set up ?
Idealith said:
and how do i get that bootloader set up ?
Click to expand...
Click to collapse
Either by flashing a whole JVU or JVZ stock firmware, or by flashing a bootloader only.
Check my sticky thread here under the same section (help & troubleshooting), I have described whole the procedure in the OP. I have even attached the files and also video is there: http://forum.xda-developers.com/showthread.php?t=2444308
Right point would be to do it first.
tetakpatalked from N7100
tetakpatak said:
Either by flashing a whole JVU or JVZ stock firmware, or by flashing a bootloader only.
Check my sticky thread here under the same section (help & troubleshooting), I have described whole the procedure in the OP. I have even attached the files and also video is there: http://forum.xda-developers.com/showthread.php?t=2444308
Right point would be to do it first.
tetakpatalked from N7100
Click to expand...
Click to collapse
thanks you so much i have now CM 10.2 running
would you know by any chance how to un simlock it ?
Idealith said:
thanks you so much i have now CM 10.2 running
would you know by any chance how to un simlock it ?
Click to expand...
Click to collapse
Ask your carrier, I assume the phone contract isn't new anymore (or expired) so you'll get unlock code for free. Here in Europe one can obtain the unlock code after 2 years for free.
Otherwise you can ask one of the online unlock services, it costs usually around 15-20$ to get the code
tetakpatalked from N7100
Idealith said:
so i tried the resistance thing but i was unable to find all of the part required so i bought one of these already done solution thingy
It worked, I'm now able to boot into DL mode
I also succesfully install a random 2.x rom from an unknown european carrier, no root, lots of crap installed, and simlocked
How do i get from that to my CM 11 rom ? (this time it's in .tar format via 7zip ^^')
I tried via Odin in PDA it says fail right away
what can I do ?
thanks fr all the answers guys
Click to expand...
Click to collapse
I'm glad that the JIG helped you (I know I'm late )
danielbe said:
I'm glad that the JIG helped you (I know I'm late )
Click to expand...
Click to collapse
yeah that worked like a charm
it was a good idea to buy it, i would have use the resistors so much
is there a more xda way to unlock it ? my carrier wants me to send the phone and have it unlock, they won't just provide the code :/
Hi i bricked my device a while ago got it working again using cyanogenmod then back to stock
Problem is my hboot thinks im on 2.16.401.2 but software on the device is 2.16.401.1
I think these need to match in order for ota to work ive tried already lots of times
Im on stock recovery and stock kernel nothing else changed
Any help would be appreciated thanks
I suggest u to flash a custom recovery and flash the last stock rom i've post on the development thread. Its the last one 2.18
Thanks for the reply will
I flashed your rom.. But it didnt work .. No radio.. I flashed the boot.img too
The phone booted but everything was screwed up. Lots of errors kept coming up
I want to be able to get stock ota to work
Did u wipe everything ?
Yes i did after install baseband is blank
I have the cyanogenmod baseband on my phone cannot change it
Cant flash radio because we dont have s off
I tried in fastboot mode and ruu mode both fail
I reflashed stock after a TWRP backup sent me into a bootloop and now my phone can't recognize the SIM or connect to Wifi. Can somebody please help?
Edit: I'm not sure why this worked, but I fixed this by trying to flash the Havoc custom ROM. The ROM wouldn't boot, but when I reflashed stock afterwards, the problem was fixed.
was your imei intact before you reflashed back to stock
enzodad said:
was your imei intact before you reflashed back to stock
Click to expand...
Click to collapse
I'm not sure if you're referring to when I reflashed stock and had problems or when I reflashed stock after trying to flash Havoc and fixed it. I can't answer either way because both times I reflashed I was stuck in a bootloop, so I couldn't check the IMEI.
hey guys i got stuck in the same problem but after flashing an android one stock rom i got back working my wifi and sim card, but now i'm stuck on this dead rom, if i try to flash another stock rom again ihte same issue happens, if i try custom doesn't boot, so i don't have a clue of what to do can someone give me some tip about it?
marken said:
hey guys i got stuck in the same problem but after flashing an android one stock rom i got back working my wifi and sim card, but now i'm stuck on this dead rom, if i try to flash another stock rom again ihte same issue happens, if i try custom doesn't boot, so i don't have a clue of what to do can someone give me some tip about it?
Click to expand...
Click to collapse
Since everything works when you have the Android One ROM installed, try backing up the EFS with that ROM installed and restoring on the ROM you want to use.
No wifi after flashing ROM
I had the same thing happen after flashing a ROM. In my case, it was a repeatable error. I reflashed the modem partition from the stock modem after flashing the custom ROM and everything started working again.
doodalydoo said:
Since everything works when you have the Android One ROM installed, try backing up the EFS with that ROM installed and restoring on the ROM you want to use.
Click to expand...
Click to collapse
Thanks for answering!
i've tried that before, always get stuck on boot on any rom and if iflash stock i lose again connections
hello
yesterday i was trying to root my phone via boot.img patch method of magisk and i flashed patched boot.img (patched by magisk) via twrp via flash image option.i know that not the right way to flash it but there was the option so i used it and i brock my phones baseband completely.
I've flashed many stock and custom roms to recover the baseband but no luck.
if any one know how can i get my baseband back please let me know.
Having same problem from yesterday after flashing custom ROM Arrow OS, my IMEI no and my sim is not catching signal, so i went back to stock still its not working. I had an TWRP nandroid backup but after restoring it gives error encryption unsuccessful and files cant be accessed and tells me to factory reset so i factory reset it but still it doesnt boot
Vinay425003 said:
Having same problem from yesterday after flashing custom ROM Arrow OS, my IMEI no and my sim is not catching signal, so i went back to stock still its not working. I had an TWRP nandroid backup but after restoring it gives error encryption unsuccessful and files cant be accessed and tells me to factory reset so i factory reset it but still it doesnt boot
Click to expand...
Click to collapse
it can only fixed by qcn file of the phone that's the only way now
CxRoxx said:
it can only fixed by qcn file of the phone that's the only way now
Click to expand...
Click to collapse
It got fixed when I flashed stock rom after removing my Sim card and putting it back inside after boot
Vinay425003 said:
It got fixed when I flashed stock rom after removing my Sim card and putting it back inside after boot
Click to expand...
Click to collapse
you got lucky I'll try that but my issue is different flashing an image through twrp brock ma baseband so can't say
CxRoxx said:
you got lucky I'll try that but my issue is different flashing an image through twrp brock ma baseband so can't say
Click to expand...
Click to collapse
Yup my baseband also became unknown after flashing custom rom through twrp but I downloaded the firmware and flashed it through fastboot but it was still not working so I read somewhere to remove the Sim before flashing and it worked you should try it too
Vinay425003 said:
Yup my baseband also became unknown after flashing custom rom through twrp but I downloaded the firmware and flashed it through fastboot but it was still not working so I read somewhere to remove the Sim before flashing and it worked you should try it too
Click to expand...
Click to collapse
I'll give it a try thanks man