Using NFC with ZeroLemon Battery [Proof-of-Concept] - G4 Accessories

A short warning in advance: What I did here could have gone horribly wrong (considering my soldering skills). I am not responsible for any broken devices that occur because of users following these steps. Oh - and please excuse the ****ty image quality. Since I could not use my good phone camera I had to use my not that good tablet-camera for the images.
I got my ZeroLemon battery and I thought: "Why should it not be possible to use NFC when I have the battery attached to my phone?". A short time later I got:
-NFC Sticker for G4 from Amazon
-Some solder
-A soldering iron
-Two short cables
What I did:
First solder the two cables on the NFC-contact-poinst of my G4 and on the other end on the NFC sticker. And guess what - it works. I did not even have a problem putting the case back on. So now I can enjoy NFC and a huge battery (and I am pretty bad at soldering so I bet you guys can do this easily). I also made a short video showing that reading a NFC sticker and using Android Beam works:
What I did (more details):
Take off the back cover of the G4
Test run (no soldering yet but hard to get working)
Get two short wires
Use duct tape (or your fingers) to hold them in place on the two lower contact pins on the right side next to the battery-tray
Hold (or duct tape) the other ends of the cables to the NFC sticker (lower pin to lower golden contact point on the sticker, higher pin to higher golden contact point)
Wake up the phone and place NFC tag on the sticker
If if works you can start soldering because it will work too (if you are careful and don't break anything)
If it doesn't work make sure the cables are really touching the contact points on the phone AND the sticker (and that they each touch only one contact point on every side) and try again
If it still doesn't work try a) a different cable b) a different NFC Sticker
The real deal:
take out the battery
(optional: make sure the cables are straight and not bent. Will make working easier)
CAREFULLY solder one cable end on the lowest contact point on the phone
CAREFULLY solder the second cable on the contact point above
CAREFULLY solder the first cable to the lower contact point on the sticker
CAREFULLY solder the second cable to the upper contact point on the sticker
Put battery in and test
Tipps for getting the cables bent right and put the case over the phone:
hold your finger onto the soldered contact points on the phone (as soon as they are cooled down a little bit) and try to bend the cables so that they run on the side of the phone (be very careful here because the nfc contact points can break)
Insert ZeroLemon Battery
CAREFULLY bend the cables on top of the battery and place NFC Sticker there
CAREFULLY put the ZeroLemon Case over the phone and battery
Test
https://youtu.be/wRpFw7o3Mbk

Neat. It's a shame zerolemon didn't come up with a sollution. My g4 came with two backs so I could use the sticker from one right?

megahypercat said:
Neat. It's a shame zerolemon didn't come up with a sollution. My g4 came with two backs so I could use the sticker from one right?
Click to expand...
Click to collapse
Of course (if you manage to get the NFC sticker off without breaking it). I originally bought the spare one because of qi-charging but did not wire up those cables (I do not plan to wirelessly charge this battery because it would take forever)

Related

[Q] Repair Manual for Nexus one?

Ok, so i have the "power button failure" problem. No more warranty, and the local gsm repair shop can repair it, but doesnt know where the connections go, to make a bypass.
anyone has this manual, or anything that could help me?
thank you
You can't repair it.it needs a new flex cable.
Sent from my Nexus One using Tapatalk
cobrax2 said:
Ok, so i have the "power button failure" problem. No more warranty, and the local gsm repair shop can repair it, but doesnt know where the connections go, to make a bypass.
anyone has this manual, or anything that could help me?
thank you
Click to expand...
Click to collapse
I had this problem recently. Out of warranty. Sent to HTC repair center and got quoted for about $50 USD (given that I'm in Singapore, there is a physical HTC service center that I can go to).
If you want to fix it yourself, you can buy the board from ebay, this is the cheapest of them all, with tools included.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=290522246328&ssPageName=STRK:MEWAX:IT
You can follow some disassembling guide from ifixit or this youtube series (very detailed, but to repair the cracked screen instead) to replace the flex cable and board. Should not take more than 1 hour. I planned to do it if the quote is higher than $80, but it's not.
Let me know how it goes if you decide to fix it yourself. Take a few pictures as you go along would be great too.
Easy way to start nexus one with out power button:
1)Plug in phone through USB or wall charger.
2) take battery out
3) put battery back in real fast
Phone should boot on.
Sent from my Nexus One using XDA App
thank you guys for replying, i knew i can replace the board, bu i wanted to see if i can "fix" the flex cable. i gues there are only 2 wires inside it and i need to see where those go. not to fix it myself, but the guys at the shop. i think they can use a "strap", which is a loose wire connecting the 2 points. i dont really plan on using that button very much, i got used to the trackball wake, but, i want it to work, just in case
cobrax2 said:
thank you guys for replying, i knew i can replace the board, bu i wanted to see if i can "fix" the flex cable. i gues there are only 2 wires inside it and i need to see where those go. not to fix it myself, but the guys at the shop. i think they can use a "strap", which is a loose wire connecting the 2 points. i dont really plan on using that button very much, i got used to the trackball wake, but, i want it to work, just in case
Click to expand...
Click to collapse
I've taken my 2 nexus apart, and I can tell you that there is no easy fix.
ok, update
i have fixed it in the gsm repair shop. well, they did
they waited to come in another faulty nexus to check which wires were faulty, compared them, and they put in a new external wire replacing the old one on the circuit board. everything works now. it costed me around 30 usd. anyway, i intend on using trackball wake though in the future, only if necessary the power button
Hi ,
Yes you can repair this problem. Besides the option of buying a new flex cable for 50-80 USD, I found in this very same forum a thread where somebody posted a picture and indications about how to repair the flex that contains the power button.
If you disassemble your N1 and remove the large flex that carries the power switch you will notice that i has two large connectors on the bottom end.
One of these has 44 pins (two rows of 22 pins). In the top row of this connector, counting from the right the pin number 10 is the one that turns the nexus one ON/OFF
The switch does this only by connecting it mmomentarily to ground.
TO FIX IT:
All you need is a fine end soldering iron, a good lens, a T5 screw driver, soldering wire and adhesive tape. And most importantly 20 cm of very thin magnet wire (enamelled copper wire of about 30 to 50 micrometers in diameter (it is thicker than hair do not worry).
Then solder an end of the wire to the pin #10 as counted in the way i described. route and tape the wire along the flex until you get to the switch.
the switch has 4 pins one pair is ground, the others go to pin #10 in the 44 pin connector. The ones that are gong to the pin #10 are actually on the side of the switch that has a golden "[" bracket. Solder the end of the wire that comes from pin #10 to any of these two pins of the switch. This completes one part of the process. (the most difficult).
The back of the board that holds the switch has a large ground plane. Solder a second piece of wire to this golden pad. From there, stretch about 30 mm of wire towards the upper corner of the logic board, and solder the end of it to the round golden pad where a screw goes. This is a ground point.
Reassemble the phone. Your power switch should now work again.
I hope this helps.
Jose
This may seem obvious to the tech savvy but not to all.
I bought a new flex cable/board on ebay. It was supposed to be new but it is obviously used. I have my doubts that it works. I am trying to test it before installing. If I press the power button, pin 10 (as described) should be electrically connected to ground, right? This is not the case with the board I have. Is the connection between pin 10 and the switch a direct trace on the ribbon cable or is something else involved? is there a diode or anything else in this circuitry? Does the battery holder come into play?
Other information. My phone does power on with the charger/remove/replace battery trick. All other buttons work.

[HARDWARE] Dinc Seamless Wireless Charger stock battery (NO USB STICKING OUT)

>>>>>><<<<<< PDF With All Steps And Images Added For Your Viewing/Downloading Pleasure >>>>>><<<<<<
***If this does not belong here I appologize, and feel free to move this if necessary. I just figured the development community is most likely to take this "upgrade" on***
After seeing that someone used Palm's wireless charger on their non-palm phone; I decided to put one on my Droid Incredible.
***This was done to a completely stock Dinc. I did not use any special back, and the stock back gets to stay on (unlike in the other video that I saw)
Wireless Charging the Droid Incredible
**Disclaimer: This will void your warranty, and if you solder something wrong will probably break your phone. With that said I can in no way be held accountable for anything that occurs while performing this “upgrade” to your phone.
>>>>If anyone knows where I can buy that little void sticker that you will see in a picture below, please let me know! If we can get that sticker then our warranty is not voided by doing this.
Supplies:
1.Palm touchstone charger http://www.shopping.hp.com/product/handheld/categories/palm/4/accessories/FB300AA%23AC3
2.Palm touchstone phone back http://www.shopping.hp.com/store/product/product_detail/FB306AA%23AC3?
3.Micro USB cable
4.Soldering Iron (the finer the tip on this the better)
5.Torx T6 screw driver
6.Safe pry tool (or a small flat head screwdriver)
7.Very tiny insulated wires (I just pulled mine out of a USB cable that I cut up)
8.Electrical Tape
9.[Optional] Multimeter to test that you actually made a good connection
How To (Images are of a higher quality (12mp) so I had to stick them in zip files to get them on here):
1.The palm touchstone phone back has a sticker inside of it that encases the wireless charging receiver, so you need to peel this off. Once it is peeled off it will look like this (without the wires soldered onto it):
(Images can be seen in: Palm Receiver.7z)
2.Remove the battery cover and the battery then unscrew the back from your phone (please view a tare down video for details, there are plenty of them on you tube that I used for a reference.)
1.All you need is a torx t6 screwdriver and a safe pry tool, I used a small flat head screwdriver and it worked just fine. Unscrew the 4 screws around the sides and then carefully pry off every place that the battery cover clips on, as they also hold on the red back.
(Images can be seen in: Dinc Inside.7z)
3.Solder on some wires to the USB connector as shown in the below image without soldering onto the pins next to them. This is difficult and takes some time and patience, since these connectors are very small and close (note the polarity in the image, notated in red).
A.Also it is necessary to place a piece of electrical tape over the components right next to the connector (Green box in the image) as they will short out the power and make it impossible to charge your phone if you do not (I found that out the hard way and went back and fixed it).
B.One final note here is that I had to melt down the red phone backing inside to allow the cables to get past the case. See the green rectangle in the image above for where I had to do that. I just used my soldering iron and melted it down, it makes a pretty nice indention for the wires to fit through.
(Images can be seen in: Dinc USB.7z)
4.Now push out the rubber plug in the red phone backing next to the USB cover (this is encircled in Green in the image from step 2).
A.Run the cables that you just solder on through that so that they are sticking through to the battery compartment on your phone.
B.You can also stick on the palm receiver to the inside of your phone cover (note the direction and placement, as this is necessary to close your cover).
3.Note that I placed electrical tape over the wires. This was necessary to keep them from breaking off of the USB connector since the solder points are so small.
(Images can be seen in: Almost Done.7z)
5.Solder on the wires to the palm charger receiver and you are done. Now you just need to carefully place the wires towards the middle of the phone so that you can close the back of your phone entirely (this is another reason why the wires need to be small).
A.Note the polarity of the connection.
B.Also I put a piece of electrical tape over the connections on the palm charger receiver to protect them (not shown in the image).
(Images can be seen in: Wireless Charger.7z)
Here is a video of the end product and how it works:
http://www.youtube.com/watch?v=YOMVJ-vmWpg
Also I just verified that my compass is working without any problems.
This could be truly amazing. I can't wait to see more.
ThugEsquire said:
This could be truly amazing. I can't wait to see more.
Click to expand...
Click to collapse
Its been done with the Evo, but don't know anyone who did it with the Inc.
http://www.goodandevo.net/2010/06/h...rk-with-palm-touchstone-wireless-charger.html
Sounds really nice. Not gonna try it with mine because I'm too scared
Though shouldn't this be in accessories or general?
What are you doing to align the coils? My biggest concern that's kept me from this is the magnets also would mess up the compass sensors readings which I for one actually value.
Wow, you managed to bring me out of my months of silence in posting...
I feel honored that I can get you out of your months of silence
The coil alignment is handled by the magnets inside of the palm touchstone charger itself (the base unit that plugs into the wall). The metal objects that you can see in the "Palm Receiver.7z" file are actually not magnets, but small circular pieces of metal that get pulled towards the charger base when you get them close to each other. So when you have the phone off of the charger, there are no magnets to mess with anything
Also you will notice that there is a piece of metal behind the coil, and that seems to block the inductive signal all together (because I tried to put it on backwards to no avail). Therefore your phone is mostly protected from the inductive transmission.
The only thing that I noticed, is that the touchscreen on the phone is a little weird when it is on the charger, but I see the same side effects when plugging the phone into a "non-htc" charger (before performing this "upgrade"). **I also saw this on my Moto Droid when connecting it to a 1 amp charger, and I have seen this with multiple other touchscreen devices so I think it just has something to do with the frequency of the charger.
Also in case of any concerns: MY PHONE HAS IN NO WAY BEEN DAMAGED BY THIS "UPGRADE"
pianoplayer said:
Sounds really nice. Not gonna try it with mine because I'm too scared
Though shouldn't this be in accessories or general?
Click to expand...
Click to collapse
Yah, it probably should be, and may get moved (which is perfectly fine by me). I put it in here because I am a developer and much more likely to do this, so I figured the development community would be more interested.
ThugEsquire said:
This could be truly amazing. I can't wait to see more.
Click to expand...
Click to collapse
You mentioned that you can't wait to see more....?
What more would you like to see? I am happy to add to the posts, but just not sure what further details you would like to see.
nevetsvsx said:
Also in case of any concerns: MY PHONE HAS IN NO WAY BEEN DAMAGED BY THIS "UPGRADE"
Click to expand...
Click to collapse
I trust your method, I just don't trust my shaky hands
BTW there is a multi quote button so you dont have to do a separate post for each reply
I have a rubber case on my Dinc... would I need to remove it for charging?
___________________________________
Yup.... The ones yoe momma told ya about.... Bad Seed Customs!!
I think you will be ok if it is one of those thin (about 1mm thick) rubber cases. Anything thicker than that and you would probably have to install the wireless receiver on the case itself and remove your battery cover all together.
I tested a thin rubber case that I have (no more than 1mm thick I think) that fits a Droid Eris and it charges as long as its flush to the back of my phone.
Sent from my ADR6300 using XDA App
Wow, this is amazing, very well done. I think this is the first hard mod I've heard of for an Android. I guess gold cards were a sorta gray area.
I've had my Incredible modded to work with a Touchstone since around June of last year. It works great, but I must caution anyone thinking of doing this to be VERY careful. Experience with soldering and a steady hand is a must. One could fairly easily mess up their phone attempting to do this.
Could you do this with a powermat if you wanted to? I have a few laying around I could use.
Sent from my ADR6300 using XDA App
Paul600k5 said:
Could you do this with a powermat if you wanted to? I have a few laying around I could use.
Sent from my ADR6300 using XDA App
Click to expand...
Click to collapse
Sure, if you wanna take apart one of those generic receivers and try to fit it inside your phone!
nevetsvsx said:
You mentioned that you can't wait to see more....?
What more would you like to see? I am happy to add to the posts, but just not sure what further details you would like to see.
Click to expand...
Click to collapse
What I originally meant was pictures. But now that you've added them and I've seen the glory, this mod is really quite impressive and I'm thrilled you shared it with us. But now that I think about it, could this also do USB wirelessly? That would be pretty amazing.
ThugEsquire said:
What I originally meant was pictures. But now that you've added them and I've seen the glory, this mod is really quite impressive and I'm thrilled you shared it with us. But now that I think about it, could this also do USB wirelessly? That would be pretty amazing.
Click to expand...
Click to collapse
No, the transmission of data wirelessly is achieved through modulated EM waves. This is simple inductance: a changing electric field creates a magnetic field, a changing magnetic field generates an electric field, so a current carrying loop placed near another loop of wire will induce current in the other loop. The receiver in the phone is engineered to "create" the "proper" amount current to charge your battery when combined with the base. In theory yes, but not with this equipment.
How does the phone treat a USB cable being plugged in - will it charge ok, and have your data transfer rates been adversely effected? I wouldn't think so, since you're only touching the power...
Mr. Spontaneous said:
How does the phone treat a USB cable being plugged in - will it charge ok, and have your data transfer rates been adversely effected? I wouldn't think so, since you're only touching the power...
Click to expand...
Click to collapse
I have used the USB charger and data transfer cables without any problems at all. Also I have copied some files off of my phone to my PC since the "upgrade" and did not notice any extended times or anything that would remotely make me think something was wrong.
I did not run a speed test before and after to see if anything slowed down, but as you said we are only touching the power pins, so I highly doubt anything has changed.

Homemade Nexus S Dock with resistor trigger

After a bit of searching I made a dock for my Nexus S and thought I'd show the results here.
I found out about polymer clay in this post (the thanks button is disabled for some reason...).
And I used the resistor values listed here, as some other threads showed they also worked with the Nexus S: Fun with resistors (home/car dock mode + more)
I ordered a Sparkfun microUSB breakout board, bought some resistors at a local electronics shop and four blocks of black Fimo clay at a nearby arts shop. I had the other supplies on hand:
-Soldering iron, solder, etc.
-Shrink wrap in various sizes.
-Hot glue.
-Aluminium plate.
-USB cable.
-Narrow and slightly rounded file.
-Box cutter or exacto knife.
I made the cable first (and did not take pictures at that time) and ensured that part worked before tackling the clay portion of the project.
I soldered one end of the resistor on the breakout board and the other directly on a stripped portion of the ground cable. The data wires remain functional as I am using a wall charger that properly shorts the D+ and D- wires to enable AC mode. I secured everything to the board with hot glue and finished off with shrink wrap.
This was my first time working with Fimo and it went well. I wrapped my phone in cellophane for a test fit along with the modified cable. The cable however isn't rated for the baking temperature so this was only temporary.
After baking, it turned out that I had misplaced the portion meant to hold the cable, so I snapped it off and made another with some left-over clay. The cured material can handle rebaking with no issues.
A bit of rework on the attachment point with a knife, test fit again, glue the board and file a notch for the buttons.
The phone slides in and out smoothly. I'm quite satisfied with the results.
Update: dock still works great. I've made one mod though: I took an old mouse pad, tore off the cloth on the top, cut a shape matching the dock's bottom, and hot glued the two together. This anti-skid pad means I can turn off the alarm or answer a call (which the phone answers in speakerphone mode right away) without inadvertently moving my phone on the nightstand.
Goodbye,
Darkshado
Wow really cool, and might have to try it.
Sent from my Nexus S 4G
nice work! I still have mine intact and it suffered some serious banging. Love your design too! Cheers.
a video of the process would be awesome for us noobs
Thanks for the feedback!
daudster: sorry, but its too late for a video. The good news is that there are plenty of good soldering tutorials out there.
This post by Fallon also has nice pictures that are very close to what I've done myself.
I started with the cable.
My "donor" USB cable was a standard compliant color coded affair. (Red Vcc, Black Ground, Green D+, White D-)
Checking with a multimeter to be safe is a very good idea.
Given the gauge of your typical USB cable wires and the breakout board's holes I suggest you presolder your wires.
Holding the stripped end of your wires with a sufficiently massive pair of pliers will make a nice heat sink to prevent melting the insulation when soldering.
Instead of doing like Fallon and placing the resistor above the breakout board, I soldered one pin on the board, the other on a stripped section of the ground cable "downhill" from the board. If you want to do it like this, make sure that you don't short your resistor with the ground cable. Then cover with shrink wrap.
Lousy ASCII art diagram below:
(Breakout board on the left)
ID--------R------\
GND--======---====
Depending on your exact design, this may not be necessary, but I opted to secure the small gauge wires to the board with hot glue, prior to covering with a larger diameter length of shrink wrap. While this cable's solidity might not be commercial grade, tugging on the cable by mistake would not risk as much damage.
Also a departure from Fallon's post is that I am using a Samsung OEM wall charger that shorts the Data wires in the charger itself, enabling AC mode, so no need to do it on the breakout board. My cable is confirmed working on the computer with both ADB and USB Mass Storage file transfer.
Test as you go to make sure none of your solders introduced unwanted short-circuits. (Fail to do this is and you could very well KILL your precious Nexus S or computer.)
Now, the Fimo part.
This was my first time ever working with Fimo and it turned out to be easy. As you work the material you heat it a little (friction) and it becomes a bit tacky to the touch so I worked on a small sheet of aluminium foil, wax paper might be better yet.
The aluminium plate is used for curing, as its much easier to handle with oven mitts and solid enough for this purpose.
Roll three blocks of Fimo in a sheet about 6-8 mm (¼") thick. With a blade, cut the excess on each side to end up with a properly sized rectangle for the back and bottom of the dock. These leftover bits will serve to support the back as well as the breakout board.
I kept my back flat, you may want to have it curved like the Samsung OEM one. Your choice, I chose flat because its easier to make and to simplify reuse with minimal modification when I'll change phones down the road.
The notch in the bottom for the buttons may be done before or after curing. Before, your fingers, a pen, coffee stirrer sticks or popsicle sticks all work. After, a rounded file or sandpaper.
My first breakout board support was misaligned so I had to break it off. For this reason I suggest you consider doing it in a second curing. This way your test fits are going to be much more accurate.
Most cables aren't rated for high enough temperatures to follow the Fimo in the oven for its curing. That's what lead me to making a support with a notch and using hot glue to finish the job. It's also flexible enough in case your alignment isn't perfect.
Goodbye,
Darkshado
Realy nice work
a quick sanding and molding would of gone miles to make it look normal!
i think that i'm going to try this!
thanks:good:

DIY Wireless charger for Droid4

Hi!
First, I'm sorry for English, I'm not professional.
A few days ago I made a working wireless charger for Motorola Droid 4.
What are the benefits?
People says, the original inductive charging cover is not compatible with most of cases.
Who live away from USA, can't use a wireless charger, becouse it is only available (officially) in the US. It is very hard to find on eBay or any other site. Almost impossible.
Very cheap. The original charging cover at US, Verzion is $29.99. (+ shipping, and need a person who ship it to me) It is only a cover, and we still need a charger as well.
So, I found a charging pad with and without receivers. There was a small problem. The receivers are only for Samsung Galaxy S3, S4 and Note. Their connectors aren't compatible with Droid 4, but the charging voltage is OK.
We need to take it to compatible with Droid 4. I looking for a long time, which one can I choose. Fortunately I made the right decision.
I bought that: Qi Inductive Wireless Charging Upgrade Kit for Samsung Galaxy S3
Link here
That is only for $30.10 with EU plug. The package include charging pad, usb cable, 1500mAh charger and S3 compatible receiver, and worldwide free shipping.
The size of receiver unit is compatible with free space of phone. We need some cutting but it isn't horrible.
First, I recommend you try, how fits the module in your phone.
Then mark with a felt.
The electrical connector pins are big, (and incompatible) we need to remove it carefully. I used a rework station with hot air (360°C) but you can use a medium sized soldering iron. I think, about 50-60W of power is enough. It took for about 30 secs per pin.
It is important, you need to place the receiver in such a manner, if you remove the back cover, the S3 and some other text need to be visible! Otherwise it will not work!
You see backside of the phone, and the camera is on top. Removed cover. In the right side, you can see four copper pins. The top row is irrelevant. We need tha bottom row. In the bottom row, on the left tere is the +5 V pin. On the right, there is a Ground pin.
We need to make contact between +5V pin of the phone and the +5V charging pin of the receiver unit.
Place the receiver unit to the phone, and see what size of copper wire you need. The lower pin of receiver unit is the +5V. We need to connect it.
I used a wire,1 mm in diameter. It is lacquered, I cycled down it from an electrical part (coil).
I think, that half millimeter in diameter is enough, but a found that, and it is recommended due to the relative high current (about 1A).
When you use thinner wire, you can easier take the cover to the phone.
So you need to solder wire to receiver's +5V pin. Please use the minimum quantity of soldering wire, becouse if you make a big knot there, you will have not enough place to take cover back.
When it is done, you can see how can you bend (or cut) the wire for best connectivity with phone's 5V pin.
Now you need to solder a wire to ground, like the previovus one, but not sure, that the two wore have enough space, and we can make easily short corcuit.
For this reason, we will use the iron cover of the SD card slot. This is a very good ground point.
So, one cable will go down, other is go up. They can fit and the soldering is more easy.
PLEASE BE CAREFUL! I recommend, before you make any electrical or hot operating you need to put an aluminium foil or an iron plate to top of the battery. I think to taking out battery and then in, is not easily possible, becouse after soldering there are the receiver. The battery can damage and explosive! The plastic parts of pohone can tolerate the heat for sort time! If you can not solder succesfuly, you need to wait while the parts cooling down! I recommend, use flux and/or high quality of soldering tin. Take out the SD Card! Please don't make short circuit!
It is not too difficult, but you need to be careful and attentive.
When the soldering done, you can try the charger.
Before you can take cover to phone, you need to cut the lower center of receiver. (you can see on the cover, exactly where. There are a claw and on the phone there ara a hole) Important! We need all of holes on phone, so the wires must not hang in to holes.
I cut the piece of receiver unit from lower left side, at the speaker.
Thats all. We are done. I think it longer to read than make :cyclops:
I made some pictures, I will mark these and upload in short time.
I'm going to measure the charging time with:
1,5A USB charger (direct cable)
1,5A USB charger with wireless charging pad
1,5A USB charger with wireless charging pad (phone in a 1 mm thickness of Trident case)
0,5A standard laptop USB (direct cable)
0,5A standard laptop USB with wireless charging pad
0,5A standard laptop USB with wireless charging pad (phone in a 1 mm thickness of Trident case)
I use that from 3 days ago. It works correctly. By the factory, the charging current is 1000mA with the 1,5A charger. About 66% of efficiency.
The USB charger's stand by consumption is 0,4W.
When the charging pad is connected and it is in stand by mode, the consumption is 0,98W
I'm going to bring images, and refresh the post, but here (Hungary, GMT +1) the time is am 2:31.
Good luck guys!
---------------------------------
Uploaded images,
here are the original, better quality images. (11.5MB zip)
That great way to charge the phone. i know that my usb plugin is getting a little wore out.......glad to know that there another way to charge up the phone in case of emergency. Congrats.
Hi,
thanks, it works for me
My IQ receiver was a bit higher, or the battery, so I had troubles to fit it in. My solution was to cut every superfluous piece and pull the uper layer of slide away. Additionally, I put it a bit nearer to the camera, The last thing was to horizontally cut the gold contacts and solder the wire directly on them.
During charging, the usb charger+pad+droid 4 use 7W, without the droid 4 the pad+charger draw 0,4W, both measured at the primary side ot the charger.
Best regards,
mifritscher
Thanks for the info, looks promising I love your using Micro SD casing as GND
BTW the pad + receiver can be found at eBay for as low as US $12 Gonna try out for myself soon.
Did you get to measure the charge times?
LuH said:
Thanks for the info, looks promising I love your using Micro SD casing as GND
BTW the pad + receiver can be found at eBay for as low as US $12 Gonna try out for myself soon.
Did you get to measure the charge times?
Click to expand...
Click to collapse
Charging times are about equivalent
Different approach, same result
Hi, thanx 4 the great idea.
I took a different approach to install the charging pad. I felt not comfortable to solder directly to the phone, so I used copper-tape, capton-tape and some short wires I took from old headphones to mod the pad directly into the back cover of my phone. it got a little bit bumpier (half a mm), but it charges perfectly.
I applied some solder to the ends which connect to the pins, so the copper wont oxidize and the connection has more pressure.
The pictures in better quality:
View attachment goodquality.zip
zuloo.de said:
Hi, thanx 4 the great idea.
I took a different approach to install the charging pad. I felt not comfortable to solder directly to the phone, so I used copper-tape, capton-tape and some short wires I took from old headphones to mod the pad directly into the back cover of my phone. it got a little bit bumpier (half a mm), but it charges perfectly.
I applied some solder to the ends which connect to the pins, so the copper wont oxidize and the connection has more pressure.
View attachment 2842634
View attachment 2842635
View attachment 2842636
The pictures in better quality:
View attachment 2842637
Click to expand...
Click to collapse
That's a nice solution, and pretty much how the "real thing" was probably set up. I noticed that the back has an internal indentation where the pins are to accommodate the connector, and I had experimented with how I might fit a charging pad in there (actually, it was the connectors that I saw as the biggest challenge), but didn't manage to get anything that I thought was robust enough (I was using cut down parts of a SIM card for the pins to make contact with - you look to have done a better job with the copper tape.
I'm really surprised that we can't buy a new back with all of this gubbins already installed - perhaps you should manufacture a few?
mugen 3800mAh inductive charging cover required!!!
i'm tempted to try this myself. the droid4 keeps getting better.
i just experimented with cardboard, seems to have plenty of room between the cover and the battery. i definitely need inductive charging.
Update 2016
@zuloo.de
Hi! I copied your method for wireless charging but I was too lazy for soldering. That is why I used only copper tape. I ordered under 5$ charging pad and receiver for Galaxy S3 (cheap from China) and it is working good. My receiver says that it can output only 0.8A so I guess it is little bit slow. Can you tell your feelings about the heat? I think that my Droid 4 is pretty hot but I never used wireless charging on other phones so I don't know if it is normal. But thanks anyway posting your method :good:
Here is pictures. I tried to take picture about the bump. It is not bad but you can feel it.

Magnetic charging port broken - pins fell out [Solved]

I bought a DK48 dock to charge my Z3 Compact as I did not want to faff around with the usb port cover.
After docking and undocking about 5 times the charging pins fell out. They were held on with doubled sided tape which clearly is not up to the task.
After reading an old thread and poll I do not want to send it to Sony as it should be an easy fix and not worth the time and money for them to stick it back on with some more tape.
Does anyone know how the internal pins should look? They do not appear to be symmetrical on my phone and I am concerned that they are damaged. If I hold the pins into the phone with a magnetic charging cable the phone does start to charge but If I go ahead and superglue/araldite the pins back in I might not get a good contact and then theres no going back.
What do you guys think would be the best way to fix the charging port?
Thanks in advance.
As a follow-up, I used Loctite Hybrid Glue to glue the pins back into the phone.
1. Prepare the surfaces by cleaning them with a cotton bud.
2. Apply a small amount of water to the surfaces to active the glue.
3. Apply a small amount of glue to the back of the pins being careful to not coat the contact blades.
4. Inserted the pins into the phone whilst connected to a charging cable and held it in place with an thick elastic band.
5. Waited a full 24 hours for the glue to set and now the charging port is solid.
Thanks to polar_bay for recommending the glue and method.
When I tested for a hermetic seal using GPS Status or Barometer+ to check the pressure reading I got a much more positive result (+0.4hPa) than I did before the pins came out. So that suggests the phone is now more waterproof than it was before.

Categories

Resources