Hi Everyone, i have searched through the forums and tried what has been said, but still no luck. I have a galaxy Gear V700
I tried numerous times on kies to update and it just would not play ball at all.Even leaving it over night, thinking maybe it is downloading something.
Today i have used Odin today, and flashed with V700XXUCNF1_V700OXACNF1_BTU
Within Odin it does the following
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
then it freezes. Because it had froze for about 25 minutes, i unpluged the Gear, to try again. All of a sudden Odin jumped up and said failed, and the Gear now is stuck with "Firmware Upgrade encountered an issue, please select recovery mode in kies and try again"
Problem is Kies 2 and 3 do not recognise the watch anymore. Odin seems to recognise it but wont allow me to do anything . I have tried using Odin to flash an original stock image, and have even tried the earlier Tizan.
I am still stuck...
I am a complete newbie on here and do not really know much about the phones and watches, but got so frustrated at not being able to upgrade the traditional way.
Any help would be greatly appreciated..
Many thanks
:crying::crying::crying:
I am now getting this in Odin 3.09, so it seems to be going a little further, but still fails at the end
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> V700XXUCNF1_V700OXACNF1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> zImage
s0mewhitedude said:
I am now getting this in Odin 3.09, so it seems to be going a little further, but still fails at the end
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> V700XXUCNF1_V700OXACNF1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> zImage
Click to expand...
Click to collapse
I had this issue when trying to flash an incorrect image.
Sent from my SPH-L900 using XDA Premium HD app
I have just answered your question in the Q&A forum.
Also a suggestion, please do not post questions in the General forum, and do not double post.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G800FXXU1ANFF_G800FXEO1ANF3_G800FXXU1ANFF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> modem.bin
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
//
where I can find pit file for G800F
knox , after fail flash still loaded bad
I'm trying to go back to stock and i've tried every which way. When I try to do it through Odin it fails. I've tried on every USB port I have.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Then I tried through Smart Switch and it says its a Galaxy Edge 7 so it doesn't let me do the emergency restore.
Then I tried to flash any other room though TWRP and it just says failed and give Error 7.
Any help will be appreciated.
You need to download the correct firmware for your device
I unlocked my old T-Mobile Note 4 but I would like to debrand it with Note 4 stock rom or international stock rom, I tried N910FXXS1DQC8/N910FBTU1DPL1 but as expected it fails. Just in case here is the Odin 3.12 log
Code:
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1205)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> FAIL! (Auth)
If i am correct I N910T can work with most N910F roms, but it will not work with N910F firmware, N910F bootloaders, and N910F basebands/modems.
Is there a way i can flash then use my phone to an international Note4 stock rom, without T-Mobile crap and use it with other carriers with 4G, hotspot, etc.
Thanks
im on infinity pro 8 rom
this is the stock rom i want to flash.
while trying to flash stock rom i get this:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> modem.bin
<ID:0/005> RQT_CLOSE !!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
its stuck at the downloading mode. cant boot to twrp, it would just take me to a error page when i reboot and it says:
An error has occurred while updating the device software. Use the emergency recovery function in the smart switch pc software. i tried that but nothing happen.