Hi Experts,
I am from Singapore and i have a problem with my SGS and i hope someone here from XDA can help me.
I have been flashing and trying the firmwares here but then i encountered an issue, my SGS is not completely booting and after the samsung logo i will only receive vibrations from my phone.
What i did is, i went to the download mode and used this once click but i did not noticed that this is for CAPTIVATE ONLY!!!
Now my phone is stocked in AT&T logo, just looping back and forth.. i cant even go to DOWNLOAD mode and when i plug it in USB my phone turns off..
Please EXPERTS, need your help..
Thanks in advance
forum.xda-developers.com/showthread.php?t=819551
Try this, i have the same problem, just had the resistor come in today, now just waiting for the breakout board to arrive...
Hope this help.
HELP!
my galaxy tab isnt recognized anymore by my pc!
i expiremented around with a by me created rom, and it stopped flashing at factoryfs.rfs! i flashed back roto-jme and now my pc wont recognise my gtab!
EDIT:
fixed it
pls need help
same here my glaxy tab p1000 dead
and not reconize my pc.. any tested solutionn pls
Hello
I have a Problem with my Samsung Galaxy Tab Wifi
Nothing works... cant get in downloadmode, cant get in recovery mode... cant get in System.. nothing... Screen is black if i hit Key Combos like downloadmode or recovery or just powerbutton... after 10 sec the screnn is kinda lighter... but then turn off again... nothing... dead...
any help???
Possiblte to reset it kinda? back to somethin?
Any bootloader fixer??? please help!!!!
It would be helpful to know how your tab got that way - what did you do to it?
If you did nothing, then you should make sure it's 100% recharged, from the home power, not a laptop, using the stock charger, for at least four hours.
The sympton you explain looks like your battery is already out of juice. Its die i think. Yeah, try charge it for 4 hour and see how.
RootMe2Heaven, you probably flashed a wrong firmware version on your device. I had my sch-i800 like this but i managed to solve it.
First thing, as already told here, charge it for about 4 hours.
Second, put your usb cable in the device and try to turn it on until your pc recognizes it.
Third, if your pc is recognizing your device, try to boot again but in download mode and flash a stock firmware from samfirmware.com
If you can't make your pc recognize the device in any way, when connected via usb, then you probably have a hard brick that needs a riff box to ressurrect.
The most important is to make your pc connect to device via usb, after that is just a matter of flashing the correct firmware.
Oh yaa..what firmware are you? Did you flash with custom rom? What did the last thing you do before this problem happen?? Maybe some info could help this community to assist you.
Please refer below link and do more search;-
http://forum.xda-developers.com/showthread.php?t=1133590
Hey I'm New To This And Need Help Asap...what happened is that i was trying to install jelly bean on my Note and used a .pit file..now the phone won't turn on or do anything..it just stays black...but when i plug in my phone to the computer its show up as "qhsusb_dload" but odin connects to the phone because when i plug in the phone the odin bar goes yellow and shows "Added" message....but when i try to flash with odin it always sicking at Setup Connection...please help asap..and thanks in advance
Any one there that can help me. please, my galaxy tab is bricked, the picture here is a cellphone and a yellow sign in the middle and a computer in the right. i know it is a soft brick, i encounter it when i try to flash a new kernel and it is disrupt the connector plugged out. any one here can help me to fix my galaxy tab. thank you
how about the download mode
reflash 2.2.1 in odin