So last time I used my phone in the water camera started acting erratic, I decided to put phone away. Before going in the water flaps were closed well and flush. I also did pressure sensor test before and it seemed ok. Few hours later I find it hot and with empty battery.
I saw some humidity inside of usb port flap so I put in in bag of rice and let dry overnight. Now, it turns on and seems to work (except that camera doesn't open anymore) but it gets hot while charging and doesn't really charge (just few % in 30min). If I remove charger it turns off in few minutes so pretty much unusable.
I checked humidity markers - sim card one is white, usb side one also pretty much white, maybe if looking carefully you'll see hint of pink.
Still have warranty. Also I'm abroad halfway around the world and won't be back home before June (will still be under warranty at that time).
So my question - what's likely damaged? If humidity markers are white can warranty repair shop still refuse repairs saying it's water damaged?
I'm trying to decide - to take it to repair here and pay for cleaning and new battery and maybe something else to fix charging and also lose warranty or wait until I get home and take it to warranty repair and hope that they fix or replace it for free.
Related
Howdy,
Long version:
I left my galaxy note on the counter in my kitchen which is apparently not quite level. Overnight water pooled under it(never submerged, even partially). I did not notice until my alarm went off the following morning. As of this time it was still functioning properly. I moved it, wiped off the water. Took the protective case off and wiped the water off it was well, hooked it up to the charger and went back to sleep. 15 minutes later the vibration function went nuts while it popped up complaints about low battery. I say the vibration went nuts, because it wasn't the sustained vibration like you normally get it. It would cycle on and off about every half a second. I panicked, turned off the device and removed the battery where I noticed that the battery was wet, and under the battery as well.
So I wipe it off, put in a bag of rice and go back to sleep. Approximately 15(yes, way too soon) hours later I pull it out, put the battery in and turn it on. Works fine. few hours later I hook it up the charger and it immediately complains about the battery temperature.
Short version:
Phone at in a pool of water for 5+ hours, never fully submerged. Basically if you poured water on a level surface and sat your phone in it, thats what happened.. Anyways Water worked its way inside the phone(based on disasemble that occured later), and started vibrating randomly. took out batteyr and left in rice for 15 hours. Put it back together attempted to charge, phone complains battery is too hot immedately.
Observations:
I take out the battery and disasemble the device down to the point where the circuit board is separate from the display.
The far right ( +) connector that touches the battery appears to be slightly corrodeded. I rub it with a cotton swab to clean it. From watermarks it doesn't look like anything else got wet and by now its completely dry. I don't see any 'red' spots or stickers, but I'm unfamiliar with the water damage indicators, and the information i found from searches was innacurate(no white dot on top of battery, no red marks anywhere on it)
Panic
I put it back together try again, same deal. The phone doesn't seem to have a way to view the battery temperature reading(*#0*#), so I downloaded an app called 'Doms diagnostic tool' which indicates that the battery temperature is pegged at 80 degrees C and it does not fluctuate. I don't know if this app is actually reading anything though.
Can someone who has a working phone try this out? App is free.
Is it worth putting it back in rice even though its dry even on thorough dissemble?
Any idea how to get legit data from the sensor to verify if its shorted out etc?
Would a replacement battery with out the sensor resolve this issue?
Anyone have pictures of where water damage indicators are?
I searched thoroughly and found no answers besides taking it to a service center. Since I'm in America, and this is an international phone, I don't believe the manufacturer will honor the warranty even if the phone shows negative for water damage. My service is ATT, but I bought the phone at expansys( i think).
best at this point is to check your insurance, if its covered. In some countries I read this is covered as it was accidental.
I would recommend goong to samsung and let them check it, with the true story ofc. Now if they find whats wrong, they might be lenient, or not. Anyhow then you know whats broke, and you can decide to fix it for yourself or have it fixed. At this point it sounds like corrosion on one of the boards, or shorts somewhere.
Sent from my GT-N7000 using Tapatalk 2
hey guys so my phone was dropped into a water pool "xperia z1"
tho it's supposed to be waterproof but some how water managed to get inside the phone ._.
anyways i've been putting it in rice for almost 2 days trying to turn it on from time to time but it wasn't turning on ._.
i tried putting it on charger tonight and the red charging light appeared but nothing appeared on the screen
i was afraid that something will go wrong if i tried to turn it on so i unplugged it fast and put it bk to rice
what do you think i should do?
thanks in advance
I experianced the same, but in the end had to get my screen nd power cord replaced as abnormal functionality of power cord was cycling my phone on off
Leave it in the rice for another day or two. Rice can bring dead phones back, trust me :3
My advice, send it to Sony for official repair.
They will fix it!
open the back and dry it completely even with a hair dryer on warm setting not hot and test it - if working ok then buy the rear seal gasket (ebay) and put the back back on, keep it away from water, I have open a few of these for screen repairs and taking the back off is easy
I know it seems like a stupid question but I've got nothing to loose at the moment so I'll explain my situation.
About 3 months ago I took my Xperia Z1 for a swim in the pool to see how the camera performed underwater. The screen started to go black when I took it out and then it completely shut off. I took it inside and turned it on again. It lasted a minute before shutting off so I plugged it in to the charger and got the boot logo before shutting off again with nothing: Screen was off, no led, no vibrations, nothing.
I opened the flaps and they were still white and still are today and there was no moisture or anything. I tried plugging the phone in a few days ago to see if it still works and the led turned on and it just stays like that with no action. Left it for a few hours but still nothing.
I don't really need this phone anymore because I have a Z5 now but a second handset is always nice to have. The pool water would have had a very small amount of salt in it and I think that might be causing issues. Either that or there is still water in there (unlikely) or parts have rusted or even the phone might have got shocked when I plugged it in to charge. What I was thinking was opening the ports and soaking it in water for a minute or less and then taking it out and putting it in a bag of dry rice to drain the water out of it. I'm not sure if it will work but I haven't got anything to loose so I was wondering if it is even worth giving a shot or even some tips would be nice.
tommylittle02 said:
I know it seems like a stupid question but I've got nothing to loose at the moment so I'll explain my situation.
About 3 months ago I took my Xperia Z1 for a swim in the pool to see how the camera performed underwater. The screen started to go black when I took it out and then it completely shut off. I took it inside and turned it on again. It lasted a minute before shutting off so I plugged it in to the charger and got the boot logo before shutting off again with nothing: Screen was off, no led, no vibrations, nothing.
I opened the flaps and they were still white and still are today and there was no moisture or anything. I tried plugging the phone in a few days ago to see if it still works and the led turned on and it just stays like that with no action. Left it for a few hours but still nothing.
I don't really need this phone anymore because I have a Z5 now but a second handset is always nice to have. The pool water would have had a very small amount of salt in it and I think that might be causing issues. Either that or there is still water in there (unlikely) or parts have rusted or even the phone might have got shocked when I plugged it in to charge. What I was thinking was opening the ports and soaking it in water for a minute or less and then taking it out and putting it in a bag of dry rice to drain the water out of it. I'm not sure if it will work but I haven't got anything to loose so I was wondering if it is even worth giving a shot or even some tips would be nice.
Click to expand...
Click to collapse
Resoaking your phone will help as much as trying to jump from a cruise ship in the middle of the ocean for the second time and you can't swim...
optimumpro said:
Resoaking your phone will help as much as trying to jump from a cruise ship in the middle of the ocean for the second time and you can't swim...
Click to expand...
Click to collapse
Haha yeah that's what I thought
tommylittle02 said:
Haha yeah that's what I thought
Click to expand...
Click to collapse
To clarify, the Xperia Z1 relies on closed ports to ensure waterproofing. So soaking it a second time would destroy it further.
there is a easy way you can try.
buy some electrical contact cleaner from a computer shop or maplins etc, spray that all over the circuitry and contacts and scrub it off with a paint brush, there is a good chance it will work again as it will remove any corrosion casued by water, ive repaired hundreds of water damaged phones this way and it doesnt need any special things.....
Hi,
i send my phone down the river and probably killed it. backplate was broken and charging lid as well, there is no warranty any more.
i dried it for a week in a box covered with rice and tried to turn it on afterwards. No reactions on buttons, but after i plugged in the charger, the LED got red and Display turned on showing the "Sony" Screen. after a second or two LED and screen went black and the procedure started again. and again. after a few repetitions i put the plug away. so i didn't charge the phone any longer than ~5min and have not plugged it to the PC.
first question is if someone has encountered the same symptomes and can give a statement of chance to revive the phone. Second one is: Where to start? there are lots of guides to disassemble the phone, thats not a problem i think, i have all the tools i need and a little bit technical knowhow. I want to start checking the battery, pretty shure its dead. afterwards i want to check the board for signs of corrosion. but then?
grateful for any tipps, especialy want to know whats the real death sentence for a water damaged phone. after i have seen the screen working i thought main functionality is there and only the battery died.
xant05 said:
Hi,
i send my phone down the river and probably killed it. backplate was broken and charging lid as well, there is no warranty any more.
i dried it for a week in a box covered with rice and tried to turn it on afterwards. No reactions on buttons, but after i plugged in the charger, the LED got red and Display turned on showing the "Sony" Screen. after a second or two LED and screen went black and the procedure started again. and again. after a few repetitions i put the plug away. so i didn't charge the phone any longer than ~5min and have not plugged it to the PC.
first question is if someone has encountered the same symptomes and can give a statement of chance to rivive the phone. Second one is: Where to start? there are lots of guides to disassemble the phone, thats not a problem i think, i have all the tools i need and a little bit technical knowhow. I want to start checking the battery, pretty shure its dead. afterwards i want to check the board for signs of corrosion. but then?
grateful for any tipps, especialy want to know whats the real death sentence for a water damaged phone. after i have seen the screen working i thought main functionality is there and only the battery died.
Click to expand...
Click to collapse
I would leave it plugged in and see if you can build up any sort of charge in the battery. It seems that changing the battery would be an obvious first step, if you can get enough charge in the phone to fire up the mainboard, then you will see what else needs to be changed. leave it plugged into a charger for 24 hours.
Do you want to repair it to salvage what data is on the phone or is it financial reasons? tbh the cost of new mainboard and battery, plus replacement back screen is going to be more than a second hand phone off ebay. If it's a science project then bravo, not enough people try to rescue thier old kit from the bin, but I'm saying there are easier options than pulling it apart.
Having never pulled a phone apart myself I can't really offer any more advice, but you might want to drop @Chamelleon a PM, as he regularly contributes with hardware fixes and knows his stuff.
its more about financial reasons, data is all backed up. Buying a new phone should be the last option. i want to repair it cause i like repairing things and i want to make clear that the phone is absolutely dead or not. i dont think i would buy a new mainboard/display/battery if i am not completely shure that this will fix all problems. in this case id rather buy a new phone.
i am a bit afraid that if i charge the battery for 24h and still have a circuit on the motherboard i will completely destroy it.
xant05 said:
its more about financial reasons, data is all backed up. Buying a new phone should be the last option. i want to repair it cause i like repairing things and i want to make clear that the phone is absolutely dead or not. i dont think i would buy a new mainboard/display/battery if i am not completely shure that this will fix all problems. in this case id rather buy a new phone.
i am a bit afraid that if i charge the battery for 24h and still have a circuit on the motherboard i will completely destroy it.
Click to expand...
Click to collapse
A week in rice in a warm place means there's no moisture in the phone.
The phone won't be damaged by trying to charge the battery and you need to find out if there's anything working from a full charge.
I recently had a waterdamage too. I took it apart and i saw that there was some corrosion on the board by the display connector. I put the mainboard in isopropyl alcohol (you can get that in the pharmacy). I carefully cleaned the affected part with a soft toothbrush and let it dry for a while. And now my phone is back a life and everything works as it should
Good Luck!
Didgesteve said:
A week in rice in a warm place means there's no moisture in the phone.
The phone won't be damaged by trying to charge the battery and you need to find out if there's anything working from a full charge.
Click to expand...
Click to collapse
Well, turns out this guy is right. Phone is working after charging. Vibration is dead and there are some residues of the wather in or behind the display, but nothing else i can find now. i think i will still disassemble the phone, and clean all parts. Maybe i will replace the vibration motor, but i think i can live without one...
Okay. I really need help here guys. So long ago I had water damaged my phone and I got it working again. About 2-3 months later the battery started acting up and showing percentages in 10s and soon after could only use it when it was plugged in.
Now, whenever I plug it in it immediately shows the Huawei logo and starts to boot up. Which I don't like because I remember it used to show a green battery circle before. But nevertheless its in a bootloop now. The weird thing is, I can't use the volume up button method. I don't know why. It just carries on.
Maybe I should wet the power button with water if its been held down causing it to immediately boot up when plugged in? i dont know.
If anyone could guide me or suggest what to do I would honestly be so appreciative. Thank you so much!
Could be a hardware issue. Water is causing corrosion to metal parts and if there is still a bit water inside your phone the corrosion can damage parts of the hardware. It's risky to use the phone without drying it completely. In the most bad case the battery can be shorted by the water which can cause a battery fire or explosion.
Bring your phone to a repair shop if you're not able to open it by yourself. But I think there's no hope anymore.
You should've let it dry completely before using it again.
Don't put water again to parts of the phone.
If you're able to open it, disconnect the battery and check the logic board for corrosion and water.
If there's still water you can remove it early by putting the logic board on a piece of cloth and wait for a few days.
You can also try to clean corroded parts with pure alcohol and cotton swaps.
Get a new battery to be safe, check if the old one is misformed. If it's so, don't use it again - NEVER!
Li-ion isn't a funny thing, it can be very dangerous.
If there's a shortage inside the battery or it's physically damaged it can burn out. The technology is based on cells. If the cells are getting shorted each other, a chain reaction starts and inside the battery the current flow can get so high that the battery start burning. It stops when every cell is damaged and the voltage is 0 - it's hard to extinguish such fires. There are many videos on YouTube.
So don't make fun with this, just do something if you feel safe in electronics. If not, go to a repair shop.