Bricked XT1068 after failed OTA - G 2014 Q&A, Help & Troubleshooting

I recently tried to install a lot of ROMs, with few success because I'm a beginner at this kind of things. I still managed to reinstall completely a stock KitKat version, and tried to do the OTA update to Lollipop. The screen turned down when the update reached approximately 60% and I can't even restart the phone in bootloader to restore with adb since. Can someone help me or is it helpless?

Same here.
I have a xt1068 and I was on MM, but after found that gps was not working properly, decided to downgrade to Lollipop.
The downgrade worked fine, but then came the OTA stagefright update notification and I tried to install it.
It was on the recovery screen, in the middle of the update, it suddenly blacked out and made no response to charging ou power button. I cant make it into bootloader, nothing. Dead.
Help!

same thing happened to me

So sad

Same here. I tried following some tutorials on bricked phones, but my pc won't even recognize the device as they say it should. Can someone help us? I'm about to go out and go to a technical support store, but I'd like to try on my own first... Someone there to help me?

http://forum.xda-developers.com/showthread.php?t=3345416

Related

[Q] Incredible S not getting past the HTC screen.

Would be so grateful if somebody could help me..been searching the internet for hours!
My phone is S-OFF, done through revolutionary. I wanted to update OTA from 2.3.3 to 2.3.5, but my phone wouldn't update. It would download the update and then just restart the phone, without having installed the update. I searched the net and found something that said I need to go back to S-ON by installing a RUU rom. I did so, and it worked fine.
My phone then told me I have system updates, so I followed the instructions and it worked fine. It then told me again that I have another system update, this time 2.3.5, and this time it got further in the installation process, but then when it rebooted, it got stuck at the HTC screen, with the white background.
I've tried going into recovery, hboot, fastboot, factory reset, and tried installing custom roms but nothing is helping.
Please, someone help me and tell me I have hope and that I haven't bricked it.

[Q] samsung ATIV S rebooting all the time!!

Ok.
first off, Hii!! this is my first ever time writing on XDA.
Any way, i know this is not a new issue.. but my ATIV S is rebooting every 5 seconds after the 8.1 update via preview for developers.....
i did a lot of digging before writing here and found this thread : http://forum.xda-developers.com/showthread.php?t=2718023
I followed the instructions and flashed the GT-I8750_DXBMJ1_R_signed ROM along side the GT-I8750_VJALL3_P csc (this is the only combination that gave me some results.
After flashing, my phone did manage to boot up finally but with a twist. Trying to restart the phone sends me back to the boot loop forcing me to reflash everything again.
i tried the tip from the thread to download the preview for developers app and try to update the phone again (claiming it will resolve the issue) but as soon as the phone goes to reboot before the update the boot loop comes back and we're back to squire one.... so i'm kinda stuck.... is there any kind of FIX i can try to help me sad situation? :crying::crying::crying::crying:
I've had a lot of issues with my Ativ S as well.
Your rebooting issue seems recognizable, maybe this thread will help : https://social.msdn.microsoft.com/F...ime-after-wp-81-update?forum=winphoneosissues
Anyway, I'm on the latest Developer Preview update, my Firmware version is : 2424.14.9.3
It seems the phone is much more stable now, however i'm only using this phone for development, there is no sim card present anymore.
Switched to a new Nokia for my main device.
Advice : If you want a decent Windows Phone, buy a Nokia, not a Samsung or HTC.
Thank you for the reply!
i did some more digging and found that flashing the GDR2 FW 2424 actually helps. after that the is a need to update the phone to the official GDR3 update in the phone updater in settings. i am trying that as we speak and really hope it will work
BTW this ATIV S is my backup phone and not my daily driver (i use a Galaxy s4) i just wanna fix it up to use as my work phone. my trust in windows phone is gone for now XD
EDIT: OK, so i followed the thread and applied the instructions...
at first, i flashed the GDR2 official ROM with the instructed csc file and everything booted up well. at this point they say that if the phone is to be restarted the boot loop will come back (it did when i tested it)
afterwards, i installed the preview for developers app and started updating to the official GDR3 update as instructed. it finished up and booted up well. the next step was to update to 8.1... i did and at first it worked well but as soon as i disconnected the USB cable, the loop returned again. (if i connect the USB cable back it's booting up normally)
BTW i tried doing it all from scratch and noticed that in every step of the process, if i disconnect the cable the loop come's back and disappears as soon as i plug it back in... anyone has any idea what to do next?

[Q&A] Unbrick Hard Bricked Moto G (2nd.Gen) [5.0/4.4.4]

Q&A for Unbrick Hard Bricked Moto G (2nd.Gen) [5.0/4.4.4]
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer.
Before posting, please use the forum search and read through the discussion thread for Unbrick Hard Bricked Moto G (2nd.Gen) [5.0/4.4.4]. If you can't find an answer, post it here, being sure to give as much information as possible (firmware version, steps to reproduce, logcat if available) so that you can get help.
Thanks for understanding and for helping to keep XDA neat and tidy!
A little different brick of my Moto G 2nd gen(XT-1068).plz help
Hi ,
Please dont ignore my mail just bcoz its too long. I have been following this thread from four to five days. Will you please help me ? Just have a look at my problem. I have been rooting my android phones and have good experience of testing , rooting the handsets. Recently I flashed my Moto G ( xt-1068 ) with lolipop because i was not able to wait till motorolla release it.
I tested it for few days , and successfully downgraded back to 4.4.4 kitkat. It was all fine. I love MIUI so I started my work to port MIUI over our favourite Moto G . I even ported it and was not booting. So I edited updter-script and was trying to flash it back on my xt-1068.
Now the mistake that happened was , due to some error in the script , It aborted the installation. When i checked the log from CWM , It has crossed partitioning and it aborted while extracting the directorties. By mistake I restarted the phone and since the partitions were flashed and there was nothing to execute , my phone is stuck. Its not even starting . Its getting recognised as "qhsusb_bulk". Thts why i came over this thread and tried to follow the procedure you have mensioned.
I am also getting the same error like while flaashing with blank-flash : FAILED (blank-flash:sdl-transfer-image:sdl-hello:invalid HDLC frame) and FAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet) .
So do i have the same problem that happened with theses guys who tried to downgrade their handsets from Lolipop to kitkat ? If its so , should I also wait for Lolipop release by moto ? or will i have some other problem ? Do you have any solution ? I was really wanted to make MIUI available for our Moto G . I don't feel sad for bricking of m phone but what ifeel sad is I want it back. I can't pass my day without it. i am missing it. Please can you suggest me wht should I do ?
Thanks in advance.
DONT WORK FOR ME :s
I have a moto g 2014 XT1063 and after unlocking the bootloader the phone work well for a minutes. Then i power off the phone and when i try to turn on again the phone is die :S no custom no bootloader dont charge dont vibrate not nothing uu. i try this tutorial but when i run the blankflash he trhrow me a error :/ please help me
Moto G hard brick
Someone please help all of us who have wrongly hard bricked our lovely Moto G 2014 . The blankflash is giving "Error sending packet" error. We all will be really thankful of you. Please help. Although some Devs say that we will have to wait for lolipop, but Moto G 2014 has already 5.0 available. Someone please check this thread and solve the problem.....plz..
link : http://forum.xda-developers.com/moto-g-2014/development/unbrick-hard-bricked-moto-g-2nd-gen-5-0-t2966010
same problem
Hi, i have an moto g xt1068 too and din't power on since yesterday hope to find a solution is hard bricked too.
i bricked mine.problem is the code 43 wich it won t recognize at all the device whatever driver i use.
altho it wont boot black screen i dont know if it charge or not, PC will recognize as device once i press volumedown+power button.
wich on my opinion he works somehow but it isn t recognized bt the windows 7.
i will install a fresh copy of win7 and check again maybe is just a failure from windows.
any other advices feel free to share.
firmwares
do someone has the moto g 2gen firmwares on extention .tar.gz i need them to fix my phone
Help!!
Hi people.
Well, only 2 weeks ago I got my Moto G XT1063 and I unlocked bootloader to install Soak Test of Android 5.0.2 with RetailUSA firmware. (My device's original firmware, was for Claro Colombia).
It worked well, I got it running perfect. Yesterday I saw that official/final version of 5.0.2 was available for my device with RetailUSA firmware, but I needed to do a downgrade to KitKat first, because it wouldn't work if I was in Soak Test yet.
So I made the downgrade, and it was running well, I checked for updates, and there was no updates availables, so I decided to reboot, to see if it may make the update appear. But after turning off my device, and trying to turn it on again, just nothing happened.
Now, my device doesn't want to turn on, neither in fastboot mode. And now, I don't know what to do here. So I would be really thankful for any help provided.
Thanks in advance. Have a nice day.
So here is what happened,
My phone was maybe 14% plugged it in left it charging and went to sleep.
Woke up with the phone alarm and started reading whatsapp messages, at this point the phone was already at 100%.
Maybe 30-40 seconds later, with the cable still plugged in the phone turned off, with no message, it just "died".
Now it wont boot, fastboot, nothing.
Tried some solutions i found on the internet like holding vol down + power button for more than 2 minutes, and nothing.
I really need some help here guys, PLEASE.
The phone was running latest TITAN PRIME ROM 1.1 dev3
Everything will be appreciated, thanks in advance.
partitions whacked out?
It seems I am unable to flash anything probably due to partitions broken. When I try to do a fastboot flash, It results in OKAY, but it has no effect on the device. I tried to flash the gpt.bin to partition, but the problem remains. Is there any way to repair the partitions? I tried to format in fastboot, I get the error "formatting is not supported for filesystem with type 'raw'". I am also unable to change format from recovery. All ideas welcome!
This issue came up after my phone went battery empty.
arvinoids said:
It seems I am unable to flash anything probably due to partitions broken. When I try to do a fastboot flash, It results in OKAY, but it has no effect on the device. I tried to flash the gpt.bin to partition, but the problem remains. Is there any way to repair the partitions? I tried to format in fastboot, I get the error "formatting is not supported for filesystem with type 'raw'". I am also unable to change format from recovery. All ideas welcome!
This issue came up after my phone went battery empty.
Click to expand...
Click to collapse
Same here, also due to 0% battery.
Seems these phones do not shutdown early enough before the battery voltage drops below spec. ****ty engineering.
Please, someone help us for the sake of god.
There are several people with this problem and we don't know how to fix it.
Is there any possibility, any help, anything we could test would be welcome.
Phone Moto G 2014 not turning on after flashing BlissPOP ROM
i flashed "BlissPop-v3.6-titan-OFFICIAL-20150629-1948" ROM to my Moto G 2014 Model and Rebooted after.Unfortunately phone doesnt turn on.Even unable to open Recovery Mode also. Can some one tell me a solution. My phone was unlocked,rooted and TWRP flashed too...
Im too facing the same issue.. the device is not turning on.... i jus unplugged from the charger but before putting the device for charging it was 67% battery... after unplugged the device screen jus turned into black i tot,the screen went to sleep but later the device dint turn on..... plzzzzzz guys any1 has any solutions??????????
I followed according to this thread http://forum.xda-developers.com/moto-g-2014/general/unbrick-hard-bricked-moto-g-2nd-gen-5-0-t2966010 but nothing worked....
Gave my Bricked Moto G 2nd Gen to Moto Service Center
Hey folks... I tried giving my Bricked phone to nearby local mobile repair shop and even they were of no help.They were of assumption that its a motherboard issue. Seriously i still cant digest that . How come flashing a ROM in your mobile screw up the Motherboard. I appreciate if someone can throw some light on this.
Anyways i gave my bricked phone to Motorolla Service Center yesterday as Warranty is still there.I acted dump infront of them and told Godamm it!!My phone doesnt turn on all of a sudden. They took my phone and asked me to wait for 3 days till they can figure out What in the name of God has happend to my Phone. I will let you folks know if i get a replacement ....
lijuram said:
Hey folks... I tried giving my Bricked phone to nearby local mobile repair shop and even they were of no help.They were of assumption that its a motherboard issue. Seriously i still cant digest that . How come flashing a ROM in your mobile screw up the Motherboard. I appreciate if someone can throw some light on this.
Anyways i gave my bricked phone to Motorolla Service Center yesterday as Warranty is still there.I acted dump infront of them and told Godamm it!!My phone doesnt turn on all of a sudden. They took my phone and asked me to wait for 3 days till they can figure out What in the name of God has happend to my Phone. I will let you folks know if i get a replacement ....
Click to expand...
Click to collapse
Please let me know because also I've bricked my device & want to send it to nearest authorized service center.
lijuram said:
Hey folks... I tried giving my Bricked phone to nearby local mobile repair shop and even they were of no help.They were of assumption that its a motherboard issue. Seriously i still cant digest that . How come flashing a ROM in your mobile screw up the Motherboard. I appreciate if someone can throw some light on this.
Anyways i gave my bricked phone to Motorolla Service Center yesterday as Warranty is still there.I acted dump infront of them and told Godamm it!!My phone doesnt turn on all of a sudden. They took my phone and asked me to wait for 3 days till they can figure out What in the name of God has happend to my Phone. I will let you folks know if i get a replacement ....
Click to expand...
Click to collapse
I got my device from service centre n got motherboard replaced with warranty... But got updated to new firmware ss below....
Sent from my XT1068 using XDA Free mobile app
moto g2 shows qhsusb bulk plz somebody help
hello friends.. i don't have Rif JTAG box....to unbrick my moto g2
If anybody have box plz help me...& repaire my mobile bootloader
I will pay for this....plz help help help.......call me on this no.
9465351811
state punjab distt patiala teh nabha
vpo :CHHINTANWALA
exactly same problem.
lijuram said:
i flashed "BlissPop-v3.6-titan-OFFICIAL-20150629-1948" ROM to my Moto G 2014 Model and Rebooted after.Unfortunately phone doesnt turn on.Even unable to open Recovery Mode also. Can some one tell me a solution. My phone was unlocked,rooted and TWRP flashed too...
Click to expand...
Click to collapse
i have through exactly same thing. my phone was working exellently on blisspop rom and got bricked once i installed an addon.
now i want to know what u did after tht.
not to mention i dnt have warranty now.
wanna listern to a person going through same ****.
Hello frnds ....my bro have moto g 2nd gen running on lollipop with unlock bootloader rooted and twrp recovery. yesterday i flashed resurrection rom. every thing ok today i reflashed stock lollipop rom by restoring nandroid backup... Today my bro in my absence trying to flash again resurrection rom. my bro is totally noob ...he flash kernel instand of rom which is not compatible with this rom and phone get hard brick .....i has been tried this method but nothing heppened ....plzzz give me solution plzzzzzzzzz

Moto G2 XT1069 Dead.

I Unlocked my bootloader and installed CM 13, i had alot of battery drain on standby so i flashed the Stock rom 4.4.4 kit kat via fastboot, everything was running fine,then got a new ota update to lollipop, downloaded, then the phone reboot to install, everything was fine, i let my phone on the table and got in my room to use computer, and when i come back to my phone it is turn off and i can't turn it on again, it don't even charge, nothing, it's dead.
I know that is Hard bricked and there is no way to save it, i just wanted to know what that i did wrong?
Sorry for my bad english, it is not my native language.

Bricked while updating

Today I unlocked my bootloader of xt1068, and flashed stock 4.4 firmware without re locking the bootloader. everything worked fine until 5.0 update came up and I agreed to it. The last thing I saw it was installing update. But when I checked after a few minutes later, the screen was black, wont go into fastboot/recovery PC only recognizes it as qhsusb_bulk.
I am requesting your HELP to fix this, Please help me :crying:
protivaban said:
Today I unlocked my bootloader of xt1068, and flashed stock 4.4 firmware without re locking the bootloader. everything worked fine until 5.0 update came up and I agreed to it. The last thing I saw it was installing update. But when I checked after a few minutes later, the screen was black, wont go into fastboot/recovery PC only recognizes it as qhsusb_bulk.
I am requesting your HELP to fix this, Please help me :crying:
Click to expand...
Click to collapse
I also did same thing so im also looking fo solution
I hope a solution will be there soon...
OMG same here my post

Categories

Resources