Mate s marhmallow roll back - Huawei Mate S

Hi, guys
By my stupidity my mate s marshmallow downgrade to lolipop.Now I am in CRR-UL00185B303(Andoid 5.1.1)
I try many things to go forward ..i failed many times .even stuck my phone also(thanks my old TWRP backup ).Aalo I lost my lost my security settings..iam not able to lock the phone by pin or finger print
Any body can give any suggestion..I have one marshmallow TWRP backup ..but that fails at the end of data backup..I dont know why.If i can go back to B114 also good ,,then i can update to B146 then update to marshmallow..
Lot of thanks in advance..

Try a factory reset for finger print

All,
Please do not discuss nor recommend using someone else's TWRP backup on your device. You're just asking for a phone brick to occur.
If any further discussion arises, then this thread will be closed. No questions .
-snickler

[/COLOR]
snickler said:
All,
Please do not discuss nor recommend using someone else's TWRP backup on your device. You're just asking for a phone brick to occur.
If any further discussion arises, then this thread will be closed. No questions .
-snickler
Click to expand...
Click to collapse
With All Due Respect
I Dont think that would be the case ... i was kinda stuck on a chinese crr-L09 firmware with my model being crr-ul00 Middle east . and i used a twrp backup from a european crr-l09 and then managed to get back to my stock crr-ul00 middle east firmware :laugh:

andromodgod said:
[/COLOR]
With All Due Respect
I Dont think that would be the case ... i was kinda stuck on a chinese crr-L09 firmware with my model being crr-ul00 Middle east . and i used a twrp backup from a european crr-l09 and then managed to get back to my stock crr-ul00 middle east firmware :laugh:
Click to expand...
Click to collapse
That may be the case for certain situations, but if there's a case of many people bricking their phones over some info found on here that they think SHOULD work without it properly being tested over dozens of situations, that wouldn't be good at all.

snickler said:
That may be the case for certain situations, but if there's a case of many people bricking their phones over some info found on here that they think SHOULD work without it properly being tested over dozens of situations, that wouldn't be good at all.
Click to expand...
Click to collapse
i can´t remember where i´ve found those information. i had bookmarked the bing-translated site some time ago but then deleted it since it ended in some nonsense discussion.
it was mostly about an "update" to MM, where people tried to change the phone localization from UL00 to L09 and update to B303 but failed and then used the MM TWRP Backups of some others.
Some ended in an bootloop and others had a corrupt system with FRP lock. I couldn´t tell if this happened because of corrupted backup files or because the users f****** up the recovery process.
Bing couldn´t translate everything to make sense.
They were lucky that they made a backup of the original system and so they were able to get back a fully funktional system.
i just wanted to warn you

I was running the L09C432B303 MM Beta and tried a method to rollback to B145, it was the method where you get a B114 Full OTA and flash the system.img, recovery.img, cust.img and boot.img however it didnt work I I restored my TWRP backup, however since then my version number in settings shows as
CRR-L09C900B303
Does anyone know how to get this back to C432??

i have rollback now and its realy easy.
make fallow:
install adb
download fallow:
HuaweiUpdateExtractor and Firmware 145 (when you will update 303 too)
Bring your phone in fastboot mode (make it of and hold power down and power)
install and open Huawei Update Extractor and open the FW 145
extract fallow data:
boot.img
cust.img
recovery.img
system.img
rename it so how i have named it and flash it with adb to your Phone
fastboot flash cust cust.img
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot reboot
When you will stay at 145 you can make now a Hardreset in recovery mode when you will update to MM let it boot to lollipop and go to update manual / local and update your Phone with MM update.zip
when its down go to recovery and reset your phone.
Ready

wolfsstolz said:
i have rollback now and its realy easy.
make fallow:
install adb
download fallow:
HuaweiUpdateExtractor and Firmware 145 (when you will update 303 too)
Bring your phone in fastboot mode (make it of and hold power down and power)
install and open Huawei Update Extractor and open the FW 145
extract fallow data:
boot.img
cust.img
recovery.img
system.img
rename it so how i have named it and flash it with adb to your Phone
fastboot flash cust cust.img
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot reboot
When you will stay at 145 you can make now a Hardreset in recovery mode when you will update to MM let it boot to lollipop and go to update manual / local and update your Phone with MM update.zip
when its down go to recovery and reset your phone.
Ready
Click to expand...
Click to collapse
That isnt a rollback - you'll find that when on B145 you cant activate security settings such as fingerprint ID. All it does it allow you to reinstall MM Beta Update...nothing more

brumgav said:
I was running the L09C432B303 MM Beta and tried a method to rollback to B145, it was the method where you get a B114 Full OTA and flash the system.img, recovery.img, cust.img and boot.img however it didnt work I I restored my TWRP backup, however since then my version number in settings shows as
CRR-L09C900B303
Does anyone know how to get this back to C432??
Click to expand...
Click to collapse
Fixed.....I think my downloads were corrupting on my laptop...finally fixed by downloading full B145 firmware...extracting boot.img, recovery.img, cust.img, userdata.img, system.img using the huaweiupdateextractor tool and flashing them via fastboot, once that completed I used the same firmware to by putting in /dload/ folder and when that completed I flashed the b303 update...now my region is back to C432 and I updated to B321 version on MM

Difference?
brumgav said:
Fixed.....I think my downloads were corrupting on my laptop...finally fixed by downloading full B145 firmware...extracting boot.img, recovery.img, cust.img, userdata.img, system.img using the huaweiupdateextractor tool and flashing them via fastboot, once that completed I used the same firmware to by putting in /dload/ folder and when that completed I flashed the b303 update...now my region is back to C432 and I updated to B321 version on MM
Click to expand...
Click to collapse
That´s interesting, however anyone knows what´s the difference between C432(Europe) and C900(Global)?.
I´m asking because I updated C432B145 to MM and ended up in C900B303(now on C900B321). Only issue so far is that LTE band 4 is not working, but don´t know if it was before updating to 6.0, as I was using the phone in Europe(LTE B3/B7).

rickylambert said:
That´s interesting, however anyone knows what´s the difference between C432(Europe) and C900(Global)?.
I´m asking because I updated C432B145 to MM and ended up in C900B303(now on C900B321). Only issue so far is that LTE band 4 is not working, but don´t know if it was before updating to 6.0, as I was using the phone in Europe(LTE B3/B7).
Click to expand...
Click to collapse
Only difference I could see was more options available in mobile data settings for your data plan

hi u can help me for make to downgrade from "beta marshmallow" to "lollipop" with mate's please

maurocasto said:
hi u can help me for make to downgrade from "beta marshmallow" to "lollipop" with mate's please
Click to expand...
Click to collapse
It's not yet possible...read the forum that you're posting in

Related

Question about converting Chinese version (EVA-AL00) to international (EVA-L19)?

I know something like this was asked before , but i've got confused and need help with that .
i have Chinese Dual sim version EVA - AL00 and i want to convert it to international dual sim version EVA-L19.
Is that possible ?
I've unlocked bootloader , i also found Software for L19 (all needed files : recovery, boot, userdata, firmware) . i even found Nougat (android 7.0) firwmare ..
So , can i cross flesh them ? and how can i do that?
L19 firmwares
http://huaweidevices.ru/category/huawei-p9-eva-l19 (marshmallow files)
http://www.gizrom.com/android-7-0-emui-5-0-huawei-p9-eva-l19-2/ (nougat files)
*#*#2846579#*#*
And then update from sdcard doesn't work!
use adb/fastboot to flash system, boot, cust and recovery image from L19 marshmallow and next flash with sd card method nougat update
speedster_no1 said:
use adb/fastboot to flash system, boot, cust and recovery image from L19 marshmallow and next flash with sd card method nougat update
Click to expand...
Click to collapse
Anyone has tried this?
and what commands do i need? fastboot flash boot/recovery/ect?
i don't really care about nougat at this time , i just need international rom on this .
I'm almost ok with this rom too , but if there is a chance...
Yes and thats all and after flashing make factory reset
speedster_no1 said:
use adb/fastboot to flash system, boot, cust and recovery image from L19 marshmallow and next flash with sd card method nougat update
Click to expand...
Click to collapse
I want do this too! Can u plz provide more details....! I am neq to huawei and want to remove the chinese things to my P9 EVA-AL00
Thx
Addymore said:
I want do this too! Can u plz provide more details....! I am neq to huawei and want to remove the chinese things to my P9 EVA-AL00
Thx
Click to expand...
Click to collapse
speedster_no1 said:
Yes and thats all and after flashing make factory reset
Click to expand...
Click to collapse
Hmm , you did that before?
i mean in theory i understand it's possible and i did something similar to other brands (like htc m7) years ago , but don't really want to brick this one , because i really like it
anyway what's order ?
1) fastboot flash recovery recovery.img
2)fastboot flash boot boot.img
3) fastboot flash Userdata ?? (don't think i've ever used this one before)
4) fastboot flash system update.app
this one confuses me more then others, because there is only "update.app" and not system.img or something like that ...
Ok so i've bricked it , because fastboot flash system update.app didn't work because of error
"targed data reported max download size ..."
no i'm just waiting for huawei Erecovery to download file
Install Adb/Fastboot, download lastest Marshmallow ROM for L19, download and extract Huawei Extractor, extract update.app with Huawei Extractor(system,boot,recovery,cust image), connect phone to pc with enabled debugging and flash images with commands :
adb reboot bootloader
fastboot flash system system.img
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash cust cust.img
fastboot reboot
After flashing make factory reset.
jkjambo said:
Ok so i've bricked it , because fastboot flash system update.app didn't work because of error
"targed data reported max download size ..."
no i'm just waiting for huawei Erecovery to download file
Click to expand...
Click to collapse
Eeeeehhh! Too bad...!
I thought we were supposed change the oeminfo to L19 with SRK tool in order to flash.....
Addymore said:
Eeeeehhh! Too bad...!
I thought we were supposed change the oeminfo to L19 with SRK tool in order to flash.....
Click to expand...
Click to collapse
Huawei Erecovery reinstalled software with no problem, so there is still a chance..
I was excepting exact that thing .
now our goal is to find system.img or fastboot command to flash update.app , installing boot and recovery was quite easy and had no problem with it after i unlocked bootloader (again)
jkjambo said:
Huawei Erecovery reinstalled software with no problem, so there is still a chance..
I was excepting exact that thing .
now our goal is to find system.img or fastboot command to flash update.app , installing boot and recovery was quite easy and had no problem with it after i unlocked bootloader (again)
Click to expand...
Click to collapse
So what procedures u used to brick it! I want to know it so that I avoid it in the future! Coz i want get rid of these chinese things asap....! Thx
Addymore said:
So what procedures u used to brick it! I want to know it so that I avoid it in the future! Coz i want get rid of these chinese things asap....! Thx
Click to expand...
Click to collapse
I've unlocked bootloader
then connected phone with fastboot mode (power off , then Vol down and plug usb)
and then i flashed boot and recovery which caused soft-bricking (bootloop) , because boot/recovery was for L19 and system still was AL00 .
i just need to flash system.img somehow and it will work ...
jkjambo said:
I've unlocked bootloader
then connected phone with fastboot mode (power off , then Vol down and plug usb)
and then i flashed boot and recovery which caused soft-bricking (bootloop) , because boot/recovery was for L19 and system still was AL00 .
i just need to flash system.img somehow and it will work ...
Click to expand...
Click to collapse
So, u didn't use the SRK Tools.... To change phone properties to match L19
Addymore said:
So, u didn't use the SRK Tools.... To change phone properties to match L19
Click to expand...
Click to collapse
No i didn't .
I'll try that too , but without system.img , or update.app flashing command which i don't know , i'm most likely stuck with this
jkjambo said:
No i didn't .
I'll try that too , but without system.img , or update.app flashing command which i don't know , i'm most likely stuck with this
Click to expand...
Click to collapse
Uuhhh! I thought changing from AL00 to L19 would be easy.....! I m waiting 2 weeks to be able to unlock the BL.... May be afterwards I will try....
Addymore said:
Uuhhh! I thought changing from AL00 to L19 would be easy.....! I m waiting 2 weeks to be able to unlock the BL.... May be afterwards I will try....
Click to expand...
Click to collapse
I wanted to try changing oeminfo and then flashing again , but after flashing firmware with Erecovery , it relocked bootloader and i don't really want to got same processes again , i mean unlocking bootloader will reset device and i'm tired of removing HIXX crap and installing google things (esspecialy contacts)
if there is at least 90% of chance with flashing L19 firmware , then i'll do that , but for now i think i'll stuck with this , at least for some days
Anyone with more info about this stuff?
I did converted AL00C00 to L19C432..... Everything working fine.... Anyone interested.... I can share.... It z quite simple....
Hi, could you share the steps to do the conversion.? Many thanks

PRA-LX1 I want to install stock firmware.

I want to flash my phone with stock firmware, but I cannot find it anywhere.
I am looking for PRA-LX1C738B123.
I own Huawei p8 lite 2017
I wiped my system because I wanted to install other rom, it didn't work so I want to go back to the original.
Unfortunately I wasn't smart enough to do a backup before so I am stuck atm. The bootloader is unlocked and flashing works, I can boot into huawei eRecovery and TWRP. (eRecovery gives the getting package info failed error) I have tried the dload method with other app files, it fails at 5% every time tho.
I tried using Huawei Update Extractor and Firmware Finder but I cannot find the exact firmware.
Could someone help me with installing my firmware? Oh and I am kinda new and it would be nice to get some guides,
Thanks.
I have the same problem but with a different firmware.. now only thing i can do is use dc-phoenix paid software (15$ for 72h of use). I will try that tomorrow as i also can't find exact same firmware it was on my phone.
MobileTechArena said:
I have the same problem but with a different firmware. now only thing i can do is usedc-phoenix paid software (15$ for 72h of use). I will try that tomorrow as i also can't find exact same firmware it was on my phone.
Click to expand...
Click to collapse
Thanks for reply. I will take that into consideration, but from what I see you were looking for PRA-LX1C432B106 and they indeed have the c432 roms there, however they don't seem to have the ones that I have been looking for. They have a list of firmwares online. Anyway good luck.
barnabaXXX said:
Thanks for reply. I will take that into consideration, but from what I see you were looking for PRA-LX1C432B106 and they indeed have the c432 roms there, however they don't seem to have the ones that I have been looking for. They have a list of firmwares online. Anyway good luck.
Click to expand...
Click to collapse
Yes, but any PRA-LX1C432 i tried doesn't work for me, flashing by fastboot. I believe any PRA-LX1 should work on this phone, but i will need to use that dc phoenix software to flash it.
MobileTechArena said:
Yes, but any PRA-LX1C432 i tried doesn't work for me, flashing by fastboot. I believe any PRA-LX1 should work on this phone, but i will need to use that dc phoenix software to flash it.
Click to expand...
Click to collapse
Thanks for making it clear. Please tell me if it worked or not. Thanks.
barnabaXXX said:
I want to flash my phone with stock firmware, but I cannot find it anywhere.
I am looking for PRA-LX1C738B123.
I own Huawei p8 lite 2017
I wiped my system because I wanted to install other rom, it didn't work so I want to go back to the original.
Unfortunately I wasn't smart enough to do a backup before so I am stuck atm. The bootloader is unlocked and flashing works, I can boot into huawei eRecovery and TWRP. (eRecovery gives the getting package info failed error) I have tried the dload method with other app files, it fails at 5% every time tho.
I tried using Huawei Update Extractor and Firmware Finder but I cannot find the exact firmware.
Could someone help me with installing my firmware? Oh and I am kinda new and it would be nice to get some guides,
Thanks.
Click to expand...
Click to collapse
Hello ! I think I could be of some help since I encountered the exact same problem !
edit: well I just realized I can't find your ROM with firmware finder either, sorry for the failed attempt
In your case I'd try with each firmware until one would work or a I tried them all.
You need some utilities first :
- Firmware Finder
https://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
It will allow you to find the stock ROM that fits your model
-Huawei UPDATE extractor
https://forum.xda-developers.com/showthread.php?t=2433454
It will allow you to extract the .img files from the firmware previously downloaded.
-fastboot and adb
https://forum.xda-developers.com/showthread.php?t=2317790
The programs that will allow you to flash the .img files.
Now:
1. Find your ROM using firmware finder (the model is usually on the box you received the android in).
2.Extract the necessary .img files : system.img, boot.img, recovery.img.
3.Reboot into the bootloader, connect your device to your computer, open a cmd exe (powershell in my case) by holding shift+right click on the folder containing the .img files and flash each .img file, e.g. for the system file:
"fastboot flash system system.img"
4.then use "fastboot reboot" and after that shutdown your device
(in my case even after flashing the .img files I was greeted by a blank screen, so I shutdown my device holding the power button).
5. Boot into recovery holding vol up + power buttons (be sure to disconnect your device before shutting down and powering it up again) and choose factory reset.
It should then reboot into ROM installation procedure where you will have to follow the same steps as when you booted your device for the first time.
edit: formatting
Also, as far as my limited knowledge goes, there is no custom ROM officially supported for our dear device.
JStrel said:
Hello ! I think I could be of some help since I encountered the exact same problem !
edit: well I just realized I can't find your ROM with firmware finder either, sorry for the failed attempt
In your case I'd try with each firmware until one would work or a I tried them all.
You need some utilities first :
- Firmware Finder
https://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
It will allow you to find the stock ROM that fits your model
-Huawei UPDATE extractor
https://forum.xda-developers.com/showthread.php?t=2433454
It will allow you to extract the .img files from the firmware previously downloaded.
-fastboot and adb
https://forum.xda-developers.com/showthread.php?t=2317790
The programs that will allow you to flash the .img files.
Now:
1. Find your ROM using firmware finder (the model is usually on the box you received the android in).
2.Extract the necessary .img files : system.img, boot.img, recovery.img.
3.Reboot into the bootloader, connect your device to your computer, open a cmd exe (powershell in my case) by holding shift+right click on the folder containing the .img files and flash each .img file, e.g. for the system file:
"fastboot flash system system.img"
4.then use "fastboot reboot" and after that shutdown your device
(in my case even after flashing the .img files I was greeted by a blank screen, so I shutdown my device holding the power button).
5. Boot into recovery holding vol up + power buttons (be sure to disconnect your device before shutting down and powering it up again) and choose factory reset.
It should then reboot into ROM installation procedure where you will have to follow the same steps as when you booted your device for the first time.
edit: formatting
Also, as far as my limited knowledge goes, there is no custom ROM officially supported for our dear device.
Click to expand...
Click to collapse
Thanks for help! I tried but i dont' have factory reset option. All I have is Shutdown, reboot and "Download leastest version and recovery" and after I click that all it does is wants internet connection. I logged in to my wifi but it didn't work and I ended up with "getting package info failed screen".
barnabaXXX said:
Thanks for help! I tried but i dont' have factory reset option. All I have is Shutdown, reboot and "Download leastest version and recovery" and after I click that all it does is wants internet connection. I logged in to my wifi but it didn't work and I ended up with "getting package info failed screen".
Click to expand...
Click to collapse
Yes I had the exact same problem, but once I did what I described, by rebooting into recovery (without twrp), I finally had the option to restore factory settings.
I believe the issue is in the fact you don't have access to the stock ROM for your model.
JStrel said:
Yes I had the exact same problem, but once I did what I described, by rebooting into recovery (without twrp), I finally had the option to restore factory settings.
I believe the issue is in the fact you don't have access to the stock ROM for your model.
Click to expand...
Click to collapse
I got rom that allows me to do a factory reset, it's stuck at 99% for like 2 hours now, is it normal? If not what should I do?
barnabaXXX said:
I got rom that allows me to do a factory reset, it's stuck at 99% for like 2 hours now, is it normal? If not what should I do?
Click to expand...
Click to collapse
Unfortunately I can't help you further than what I already posted.
But keep updating in case someone more knowledgeable peeks in.
similar problem....I was fairly good but play store was stuck in pending download....
I did a wipe in TWRP, and ended with a black screen...
I can boot to eRecovery, but it fails.and also to TWRP.
when attached to PC it keeps being seen and unseen as if its stuck in a power on cycle
Any help would be greatly appreciated.
Already Tested
JStrel said:
Hello ! I think I could be of some help since I encountered the exact same problem !
edit: well I just realized I can't find your ROM with firmware finder either, sorry for the failed attempt
In your case I'd try with each firmware until one would work or a I tried them all.
You need some utilities first :
- Firmware Finder
https://forum.xda-developers.com/tools/general/huawei-firmware-finder-team-mt-t3469146
It will allow you to find the stock ROM that fits your model
-Huawei UPDATE extractor
https://forum.xda-developers.com/showthread.php?t=2433454
It will allow you to extract the .img files from the firmware previously downloaded.
-fastboot and adb
https://forum.xda-developers.com/showthread.php?t=2317790
The programs that will allow you to flash the .img files.
Now:
1. Find your ROM using firmware finder (the model is usually on the box you received the android in).
2.Extract the necessary .img files : system.img, boot.img, recovery.img.
3.Reboot into the bootloader, connect your device to your computer, open a cmd exe (powershell in my case) by holding shift+right click on the folder containing the .img files and flash each .img file, e.g. for the system file:
"fastboot flash system system.img"
4.then use "fastboot reboot" and after that shutdown your device
(in my case even after flashing the .img files I was greeted by a blank screen, so I shutdown my device holding the power button).
5. Boot into recovery holding vol up + power buttons (be sure to disconnect your device before shutting down and powering it up again) and choose factory reset.
It should then reboot into ROM installation procedure where you will have to follow the same steps as when you booted your device for the first time.
edit: formatting
Also, as far as my limited knowledge goes, there is no custom ROM officially supported for our dear device.
Click to expand...
Click to collapse
Hello did you already test ???
Here is the solution for every PRA-LX1: [http : // www . htcmania . com / showthread . php ? t=1326478] (sorry for the spaces, but I don't have enough posts written to post external links )
Unfortunately, it's from a spanish forum. I didn't found any problem to follow this tutorial, but maybe for someone it could be a little difficult.
Anyway, it works!
MobileTechArena said:
Yes, but any PRA-LX1C432 i tried doesn't work for me, flashing by fastboot. I believe any PRA-LX1 should work on this phone, but i will need to use that dc phoenix software to flash it.
Click to expand...
Click to collapse
Where did you find the C432 firmware? I can't succees to find it
Flashing to a completely empty phone via DC phoenix or manual via fastboot still didnt got my device started. Sometimes I end up in the eRecovery and sometimes its just stuck at boot.
I tried different version from the hicloud but none so far did the trick. Maybe someone can point me into the right direction so i can finally rescue this phone?
EDIT:
PRA-LX1C432
Sorry cant link to these files since i don't got 10 posts. Maybe PM ?
Copied the Mega TWRP backup (B100) to SD card
Flashed TWRP via fastboot
Disconnected the USB cable
Boot into TWRP
Restored TWRP backup
Restarted phone into fastboot
OEM unlocked it
Got booted into TWRP since no stock recovery there
Booted into fastboot again
flashed stock recovery
Android started to work!
Tried to update to B164 and failed
Reboot
Now it offered B110 and I tried to update to B110. Success.
Iocere said:
Flashing to a completely empty phone via DC phoenix or manual via fastboot still didnt got my device started. Sometimes I end up in the eRecovery and sometimes its just stuck at boot.
I tried different version from the hicloud but none so far did the trick. Maybe someone can point me into the right direction so i can finally rescue this phone?
EDIT:
PRA-LX1C432
Sorry cant link to these files since i don't got 10 posts. Maybe PM ?
Copied the Mega TWRP backup (B100) to SD card
Flashed TWRP via fastboot
Disconnected the USB cable
Boot into TWRP
Restored TWRP backup
Restarted phone into fastboot
OEM unlocked it
Got booted into TWRP since no stock recovery there
Booted into fastboot again
flashed stock recovery
Android started to work!
Tried to update to B164 and failed
Reboot
Now it offered B110 and I tried to update to B110. Success.
Click to expand...
Click to collapse
Yeah, that's the way! It worked for me too!
juanmemo said:
Yeah, that's the way! It worked for me too!
Click to expand...
Click to collapse
Also i noticed everytime a OTA fails you get the full version offered on next boot. So you should get a full B164 aswell after it failed
JStrel said:
Yes I had the exact same problem, but once I did what I described, by rebooting into recovery (without twrp), I finally had the option to restore factory settings.
I believe the issue is in the fact you don't have access to the stock ROM for your model.
Click to expand...
Click to collapse
how can you boot into recovery ? i can only boot into twrp or fastboot & rescue or if i plug the huawei to the pc erecovery ???
---------- Post added at 12:16 AM ---------- Previous post was at 12:13 AM ----------
i have an huawei pra-lx1 c530 it used to boot into pra-lx1c530b111 rooted and twrp but now it doens't boot anymore, i'd like to flash to c530b160 but i can't find the firmware images
tiagoggama said:
Hello did you already test ???
Click to expand...
Click to collapse
Thanks men
I CONFIRM IT WORK PERFECTLY
For the second part go to this link for more detail :
https://boycracked.com/2016/03/14/h...-unbrick-firmware-any-huawei-android-devices/

bricked device with oreo, old unbrick doesnt work

hi guys,
yesterday i installed the oreo beta on my VTR-L29 but then i brickedd it *cry*. unfortunateley the unbrick methods found here in the forum don't work because the oreo update made some changes in the system file structure...
has anyone an idea what to do?
maybe someone can provide me a recovery image for twrp? (one for oreo, otherwise it wont work) so i can give this a try...
after over 10 hours of fiddeling around a found a really easy solution:
most of you know HWOTA helps with this, but the "normal" version wont work after flashing oreo. but this version is flashed via twrp and is still working!
but you will need a oreo compatible twrp, which you can find here
i know the links are to mate 9 software, but since the p10 and mate 9 are nearly identical, it works on the p10 as well
can you post the step by step guide?
i am on oreo 8.0.0.046 and want to flash another version, or downgrade to nougat because few things don't work on this version
i dont know if downgrading works, i just reflashed the latest oreo.
accordingly to the first link it should work, just flash the TWRP from the second link and then follow the instructions from the first link.
johdost said:
i dont know if downgrading works, i just reflashed the latest oreo.
accordingly to the first link it should work, just flash the TWRP from the second link and then follow the instructions from the first link.
Click to expand...
Click to collapse
failed install twrp- error find twrp 3.0.3, and i replaced to oero mate 9 recovery....
EDIT: success - problem was on the computer
johdost said:
i dont know if downgrading works, i just reflashed the latest oreo.
accordingly to the first link it should work, just flash the TWRP from the second link and then follow the instructions from the first link.
Click to expand...
Click to collapse
i did sucsses to install twrp but on the second step, when i press on install on twrp, the phone restart to erocovey and failed to find the files. what am i doing wrong?
i think that i am stuck with that version forever....
if you reboot to erecovery, you have not successfully installed twrp. you have to install it with "fastboot flash recovery_ramdisk <path to twrp>"
johdost said:
if you reboot to erecovery, you have not successfully installed twrp. you have to install it with "fastboot flash recovery_ramdisk <path to twrp>"
Click to expand...
Click to collapse
you misunderstood me.
i do have twrp, i created HWOTA8 folder on sd card, copied hwota8 update zip, MHA_RECOVERY8 No check and the 3 files that i renamed as it said. after that, from twrp i clicked on hwota8 update zip and begin flash, the phone reboot to stock recovery and failed to install - "files don't found".
please help me fegure out what's the problem.
thanks
t.h.i said:
you misunderstood me.
i do have twrp, i created HWOTA8 folder on sd card, copied hwota8 update zip, MHA_RECOVERY8 No check and the 3 files that i renamed as it said. after that, from twrp i clicked on hwota8 update zip and begin flash, the phone reboot to stock recovery and failed to install - "files don't found".
please help me fegure out what's the problem.
thanks
Click to expand...
Click to collapse
EDIT : the process is sucsses, but its the same version.... 8.0.0.046
Bricked, no TWRP access, any ideas?
Hi.
I know this about a P10, I have a P10 Plus (VKY-L29C605), but the process should be similar, I think.
I bricked my phone after succesfully upgrading from B174 to B321 using HWOTA. After which I decided, since I was at it, to flash the Hyperplus Kernel. This led to a bootloop. To fix it I decided to just go ahead and HWOTA B321 all over again and get over it, and would have probably gone just fine, except I decided to rebrand (C605 > C432) while I was doing that, silly (no, stupid) mistake. This led to the brick I am currently expriencing, I have no recovery access, erecovery or TWRP.
So now I am left trying to unbrick the phone. I extracted the UPDATE.APP for both update_all_hw.zip and update.zip using the Huawei Extractor Tool with no difficulty, except unbricking methods ask for boot.img, which I could not find, so I went along without it and flashed: cust.img, recovery_ramdisk.img (using fastboot recovery_ramdisk command for Oreo), and system.img. All of the commands completed succesfully, but no shebang, still bricked and no recovery access. I figure this has to do with the rebrand as the result after executing the command "fastboot getvar vendorcountry" shows the rebrand pulled through (hw/eu 432).
I am currently downloading HWOTA8.zip (3GB worth of download) to see if I can do something it. I am also downloading the L29C432B360 OTA-FULL, since I believe I am not getting any progress becuase I used the updates for L29C605B321.
The kind people at funkyhuawei told me they could fix it with their tool, but I don't have the money for that right now.
I will post updates, but any ideas would be greatly appreciated.
Many of us have posted over this in the last couple of days. Seems like Funky Huawei unbrick tool was the mehtod to get it work for me. You could try that!
or use dc-phoenix for me it worked (= in the moment i try to capture the usb ports kommunikation so i have the tool with the aktual firmware longer for 3 days :silly:
would first give dc a try 20 bucks for 3 days is ok i think (=
johdost said:
hi guys,
yesterday i installed the oreo beta on my VTR-L29 but then i brickedd it *cry*. unfortunateley the unbrick methods found here in the forum don't work because the oreo update made some changes in the system file structure...
has anyone an idea what to do?
maybe someone can provide me a recovery image for twrp? (one for oreo, otherwise it wont work) so i can give this a try...
Click to expand...
Click to collapse
Must download some software for your phone, unzip update.zip, decompile UPDATE.APP to .iso files, (like recovery.iso, system, iso, vendor iso, boot iso) use fastboot and 10 minuts job, I brik my device over 10 thimes, and repair it.
So I was able to get the C432B360 firmware and I flashed it, but no I can't enter recovery mode because the battery is low (red lightning bolt/red led flash). Anybody know how to charge or force recovery mode boot from fastboot?
If anyone needs, can use my DC-Phoenix account, I don`t need it anymore.
Your username is: cesedy
Your password is: dnL4eHEm
Greting
ure3808 said:
Must download some software for your phone, unzip update.zip, decompile UPDATE.APP to .iso files, (like recovery.iso, system, iso, vendor iso, boot iso) use fastboot and 10 minuts job, I brik my device over 10 thimes, and repair it.
Click to expand...
Click to collapse
Greeting,
Can you explain the procedure of how to do it?
Thank you

How many people bricked their phone while Rebranding/OTA and what solutions used ?

How many people bricked specifically hardbricked their phone after 2018-04-16 updates,while OTA or rebranding using any tool and choose which methods you tried to solve.
we need to show how many people we are,and seek for solution or encourage BOX groups to do something for this matter.
Even huawei may help us if they see we are bunch of people.
Edit: Just comment only if you solved the issue with this tool or any other tool that is not mentioned,here we are seeking help.
reza6d said:
How many people bricked specifically hardbricked their phone after 2018-04-16 noxloader updates,while OTA or rebranding using any tool and choose which methods you tried to solve.
we need to show how many people we are,and seek for solution or encourage BOX groups to do something for this matter.
Even huawei may help us if the ysee we are bunch of people.
Click to expand...
Click to collapse
The only versions that will brick (so far anyway) are BLA-L29C636B137 and ALP-L29C636B134 from 16/4, neither is a noxloader version.
Bricks occur when you update/downgrade/rebrand FROM those 2 firmwares.
ante0 said:
The only versions that will brick (so far anyway) are BLA-L29C636B137 and ALP-L29C636B134 from 16/4, neither is a noxloader version.
Bricks occur when you update/downgrade/rebrand FROM those 2 firmwares.
Click to expand...
Click to collapse
maybe i recall wrong but after first time seeing these noxloaders,somethings changed,anyway i edited the post.thanks.
My BLA-L29 is still on the black screen and I can not even revert to DC-Phoenix. After upgrading to 138.
Used funky
mikaole said:
Used funky
Click to expand...
Click to collapse
i think your phone was in fastboot or bootloop,we are talking about hardbrick bro,black screen not even charge led in our devices.
I bricked my Huawei Mate 10 too
Please help.. I also bricked my Huawei Mate 10 ALP-L29C636...
I installed the EMUI 9.0 on my device using the HWOTA8_Mate10 method which was successful. The EMUI 9.0 ROM was from FirmwareFinder: ROM version ALP-L29C636E2R1P8B108-log (9.0.0.108). I didn't have any issues at all but since Huawei Mate 10's EMUI 9.0 is still in Beta, I decided to switch back to the stable EMUI 8.0.
Here's where the problem started... Since I want to downgrade, I went ahead and downloaded the 3 needed files (update.zip, update_all_hw, update_data_public) from FirmwareFinder: ROM version ALP-L29C636B143 (8.0.0.143). I fired up HWOTA8_Mate10 and started the installation process. The first step was to boot to fast boot and then plug the device, after that, the software asked me to unplug the device and press volume+ and power button but the device won't boot to recovery anymore. The device is now stuck at "Your device is booting now..." I tried rebooting the device but it won't work. Tried to go to eRevovery to wipe cache/factory reset but it will go back to "Your device is booting now..." page. I tried reinstalling the recovery.img via fastboot and tried to boot to recovery mode again but it won't work anymore. I believe my device is now soft bricked . I can still boot to fastboot, I even tried fastboot flash system system.img which was successful but the device still won't boot. Please help how to recover my device. I think I went too far and now I don't know how to fix this issue.
Carnage! said:
Please help.. I also bricked my Huawei Mate 10 ALP-L29C636...
I installed the EMUI 9.0 on my device using the HWOTA8_Mate10 method which was successful. The EMUI 9.0 ROM was from FirmwareFinder: ROM version ALP-L29C636E2R1P8B108-log (9.0.0.108). I didn't have any issues at all but since Huawei Mate 10's EMUI 9.0 is still in Beta, I decided to switch back to the stable EMUI 8.0.
Here's where the problem started... Since I want to downgrade, I went ahead and downloaded the 3 needed files (update.zip, update_all_hw, update_data_public) from FirmwareFinder: ROM version ALP-L29C636B143 (8.0.0.143). I fired up HWOTA8_Mate10 and started the installation process. The first step was to boot to fast boot and then plug the device, after that, the software asked me to unplug the device and press volume+ and power button but the device won't boot to recovery anymore. The device is now stuck at "Your device is booting now..." I tried rebooting the device but it won't work. Tried to go to eRevovery to wipe cache/factory reset but it will go back to "Your device is booting now..." page. I tried reinstalling the recovery.img via fastboot and tried to boot to recovery mode again but it won't work anymore. I believe my device is now soft bricked . I can still boot to fastboot, I even tried fastboot flash system system.img which was successful but the device still won't boot. Please help how to recover my device. I think I went too far and now I don't know how to fix this issue.
Click to expand...
Click to collapse
did you tried huawei pc app (hisuite)?
your problem maybe is because magisk, try to install in twrp "magisk uninstaller". or try to install via twrp, recovery_ramdisk.img, kernel.img and ramdisk.img from the last rom of android 8 (extract with huaweiupdateextractor), then install via twrp with hrupdater 0,4 the same update.zip that you extract the kernel.img, recovery and the other img that I told you.
look at the guides of the preocesses that I told you, if you have any question let me know
durc12 said:
did you tried huawei pc app (hisuite)?
your problem maybe is because magisk, try to install in twrp "magisk uninstaller". or try to install via twrp, recovery_ramdisk.img, kernel.img and ramdisk.img from the last rom of android 8 (extract with huaweiupdateextractor), then install via twrp with hrupdater 0,4 the same update.zip that you extract the kernel.img, recovery and the other img that I told you.
look at the guides of the preocesses that I told you, if you have any question let me know
Click to expand...
Click to collapse
Yes, I tried hisuite but it says my device isn't supported. I will try your suggestion and will get back to you if I have questions
Carnage! said:
Yes, I tried hisuite but it says my device isn't supported. I will try your suggestion and will get back to you if I have questions
Click to expand...
Click to collapse
If the update process didn't even started, you need to flash stock Pie kernel, recovery_ramdisk and system, using fastboot.
This should get you back to a working OS.
Pretoriano80 said:
If the update process didn't even started, you need to flash stock Pie kernel, recovery_ramdisk and system, using fastboot.
This should get you back to a working OS.
Click to expand...
Click to collapse
I see. I only tried flashing the recovery_ramdisk and system.img. I will try it later and I will let you know if it worked.
Pretoriano80 said:
If the update process didn't even started, you need to flash stock Pie kernel, recovery_ramdisk and system, using fastboot.
This should get you back to a working OS.
Click to expand...
Click to collapse
as far as I can read, I think he wants to come back to OREO, so he has to install first recovery_ramdisk.img, kernel.img and ramdisk.img from 8.0.0.143 (extracting those files with huaweiextractorupdate) and then flashing those files via fastboot or your twrp version. Then, he has to use hrupdater 0.4 to install 8.0.0.143
Am I right Pretoriano80?
please, fell free to correct me if i have commited any mistake
PD: MANDATORY TO HAVE UNLOCKED BOOTLOADER FOR THE PROCESS
durc12 said:
as far as I can read, I think he wants to come back to OREO, so he has to install first recovery_ramdisk.img, kernel.img and ramdisk.img from 8.0.0.143 (extracting those files with huaweiextractorupdate) and then flashing those files via fastboot or your twrp version. Then, he has to use hrupdater 0.4 to install 8.0.0.143
Am I right Pretoriano80?
please, fell free to correct me if i have commited any mistake
PD: MANDATORY TO HAVE UNLOCKED BOOTLOADER FOR THE PROCESS
Click to expand...
Click to collapse
No, first he has to recover the current OS, and my advise was only for that.
Then he will need to use a TWRP + NoCheck combo, to get back to Oreo.
HuRUpdater can't get you back to Oreo so you guys should stop using that with Pie.
Mate 10 Pro BLA-L09
I also installed the EMUI 9.0 on my device using the HWOTA8 method which was successful. The EMUI 9.0 (9.0.0.108). I didn't have any issues too. After a while I decided to switch back to EMUI 8.0. using also HWOTA8 I put three zip files with EMUI8 (update.zip .....). Update ended with error. That's it.
I only have fastboot working but I am able to flash only few partitions System.img, Recovery_ramdisk.img, Kernel.img. I tried to flash them many times - nothing.
Couple months ago I messed up with my phone and I had to buy and use DC-Phoenix. It worked for me then. This time did not because DC-Phoenix only support EMUI 8. They refunded me money I paid for - that's good thing but my phone is still bricked.
Then I've found MultiTool for Huawei
https://forum.xda-developers.com/honor-8/development/tool-huawei-multi-tool-team-mt-t3523923
It shows that
https://gyazo.com/70820957c6638e27bfe79418dfb07e3e
(Firmware 9.0.0.108,device bla-l09,no serial number, no IMEI and battery status 0)
HiSuite says device is not supported.
Is there any way to force HiSuite to recover not supported device?
Anyone knows the solution?
I booked my phone for repair with Huawei Service.
diowil4 said:
I also installed the EMUI 9.0 on my device using the HWOTA8 method which was successful. The EMUI 9.0 (9.0.0.108). I didn't have any issues too. After a while I decided to switch back to EMUI 8.0. using also HWOTA8 I put three zip files with EMUI8 (update.zip .....). Update ended with error. That's it.
I only have fastboot working but I am able to flash only few partitions System.img, Recovery_ramdisk.img, Kernel.img. I tried to flash them many times - nothing.
Couple months ago I messed up with my phone and I had to buy and use DC-Phoenix. It worked for me then. This time did not because DC-Phoenix only support EMUI 8. They refunded me money I paid for - that's good thing but my phone is still bricked.
Then I've found MultiTool for Huawei
https://forum.xda-developers.com/honor-8/development/tool-huawei-multi-tool-team-mt-t3523923
It shows that
https://gyazo.com/70820957c6638e27bfe79418dfb07e3e
(Firmware 9.0.0.108,device bla-l09,no serial number, no IMEI and battery status 0)
HiSuite says device is not supported.
Is there any way to force HiSuite to recover not supported device?
Anyone knows the solution?
I booked my phone for repair with Huawei Service.
Click to expand...
Click to collapse
It should be possible to recover your phone.Tried to flash Pie B108 recovery_ramdisk, kernel and system with fastboot?
Pretoriano80 said:
It should be possible to recover your phone.Tried to flash Pie B108 recovery_ramdisk, kernel and system with fastboot?
Click to expand...
Click to collapse
I have tried. I flashed Pie 9.0.0.108 - nothing, 9.0.0.112 (chinese ver) - nothing. I tried BLA-L09 8.0.0.148(SP1C432) - nothing.
After flashing recovery_ramdisk, kernel and system of all above firmware there is no change only fastboot is working.
The problem is that downgrade process from Pie to Oreo went to 95% ( I thing - I don't remember exactly but for sure it was 90 something). It could have changed most of partitions to Oreo but left one or few unchanged (like verlist.img, xloadr.img, vendor.img, product.img).
From fastboot I am able to change (flash) only few partitions.
Do you gays know any other tools like dc-phoenix to force to flash all partitions. (Couple months ago when I used DC Phoenix with Emui 8 it used backdoor to flash difficult partitions.)
Example:
Writing XLOADER partition with file X:\Install\Telefony\Huawei_Mate_10_pro\DC_Phoenix_v50\XLOADER.img
XLOADER partition UPDATE ...FAILED
Cannot get FBlock info from device
Activating backdoor: DONE
Writing XLOADER partition with file X:\Install\Telefony\Huawei_Mate_10_pro\DC_Phoenix_v50\XLOADER.img
XLOADER partition UPDATE ...OK
diowil4 said:
I have tried. I flashed Pie 9.0.0.108 - nothing, 9.0.0.112 (chinese ver) - nothing. I tried BLA-L09 8.0.0.148(SP1C432) - nothing.
After flashing recovery_ramdisk, kernel and system of all above firmware there is no change only fastboot is working.
The problem is that downgrade process from Pie to Oreo went to 95% ( I thing - I don't remember exactly but for sure it was 90 something). It could have changed most of partitions to Oreo but left one or few unchanged (like verlist.img, xloadr.img, vendor.img, product.img).
From fastboot I am able to change (flash) only few partitions.
Do you gays know any other tools like dc-phoenix to force to flash all partitions. (Couple months ago when I used DC Phoenix with Emui 8 it used backdoor to flash difficult partitions.)
Example:
Writing XLOADER partition with file X:\Install\Telefony\Huawei_Mate_10_pro\DC_Phoenix_v50\XLOADER.img
XLOADER partition UPDATE ...FAILED
Cannot get FBlock info from device
Activating backdoor: DONE
Writing XLOADER partition with file X:\Install\Telefony\Huawei_Mate_10_pro\DC_Phoenix_v50\XLOADER.img
XLOADER partition UPDATE ...OK
Click to expand...
Click to collapse
I think you should use my TWRP + NoCheck recovery and try to flash the Pie beta again.
Pretoriano80 said:
I think you should use my TWRP + NoCheck recovery and try to flash the Pie beta again.
Click to expand...
Click to collapse
After flashing It cannot boot to recovery.
diowil4 said:
After flashing It cannot boot to recovery.
Click to expand...
Click to collapse
So you can only boot to fastboot, no matter what?
Pretoriano80 said:
So you can only boot to fastboot, no matter what?
Click to expand...
Click to collapse
Yes.

flashing rom via TWRP with frp lock?

Hi, I'm in a bad situation. My honor 9 lite (Europe) has no OS, frp lock. But it does have TWRP installed.
My question would be, since I can't flash an OS (given the frp lock) via fastboot, would it work via TWRP? Or should I just give up and buy a new phone?
Thanks a lot.
Best
Since you have TWRP, try using HURUpdater tool. It is compatible with H9L.
https://forum.xda-developers.com/honor-9/development/tool-flash-official-firmware-recovery-t3769279
BS4388 said:
Since you have TWRP, try using HURUpdater tool. It is compatible with H9L.
https://forum.xda-developers.com/honor-9/development/tool-flash-official-firmware-recovery-t3769279
Click to expand...
Click to collapse
Hi,
thanks a lot for the tip. Unfortunately, I keep getting an error when flashing following the instructions.
I discovered that nonetheless I can flash roms with TWRP. There is one particular rom, this one https://forum.xda-developers.com/honor-view-10/development/rom-t3753555 that works particularly.
However, my device with that rom keeps giving me an error "bluetooth keeps stopping". Any way to solve that?
I really don't know a solution.
Can't you enable OEM unlock in settings/developer options? so that to make frp unlocked?
Yes.
After that, I was able to finally flash stock rom
However, there's a new issue: wifi doesn't work. It actually seems like whatever rom I flash, wifi won't work the slider turns off as soon as I turn it on
Did you wipe data/factory reset through eRecovery after flashing? That is important in most cases!
BS4388 said:
Did you wipe data/factory reset through eRecovery after flashing? That is important in most cases!
Click to expand...
Click to collapse
No I did not. I think I used TWRP to do that. Will do with eRecovery next time and update you
I am still without WiFi.
I think the problem lies in the fact that my stock ROM comes from here: https://forum.xda-developers.com/9-lite/how-to/guide-unbrick-device-recover-bootloop-t3772563
I had oreo 8.1 before brick, and the rim above that I flashed is 8.0 and Indian version (not european). That maybe could explain the issue.
Problem is, I would need a system.img stock ROM to file and I can't seems to find that. In Huawei firmware finder, I only get update.zip kind of files and TRWP returns error when flashing that or when I use the HuRUpdater tool.
Also, I've noticed it's not just the WiFi, but also security options and themes for some reason
you need a working frp image which in twrp can flashed via dd... so the frp lock is gone...
In telegram group you can find image.
gabfur01 said:
I am still without WiFi.
I think the problem lies in the fact that my stock ROM comes from here: https://forum.xda-developers.com/9-lite/how-to/guide-unbrick-device-recover-bootloop-t3772563
I had oreo 8.1 before brick, and the rim above that I flashed is 8.0 and Indian version (not european). That maybe could explain the issue.
Problem is, I would need a system.img stock ROM to file and I can't seems to find that. In Huawei firmware finder, I only get update.zip kind of files and TRWP returns error when flashing that or when I use the HuRUpdater tool.
Also, I've noticed it's not just the WiFi, but also security options and themes for some reason
Click to expand...
Click to collapse
The system.app file you search for is in the update.zip file you get and you cannot flash update.zip directly from twrp, you need HuRupdater for that and the dload method doesn't work for almost anyone including me.
And you need correct the firmware for your motherboard if you want your phone to work properly.
First tick oem unlocking in developer options. Then unlock fastboot and flash TWRP.
Since you are able to boot up check your varient, the complete one not just the LLD but the rest too. Search for it in Huawei firmware finder and download the latest firmware for your model. You'll get 3 links and you'll need all three.
Download HuRupdater 0.3 zip and then rename the 3 files you got as told in the HuRu instructions. get twrp image and rename it to recovery.img and put all files in the same folder.If you want to completely revert to stock you don't have to have recovery.img but keep it just in case.
Then flash HuRupdater using twrp. You should be up and running if you did everything right.
You can then remove the recovery.img and then flash again using HuRupdater and relock the fastboot too later if you wanna play things safe using fastboot relock bootloader 'your code' .
please help me, honor 9 lite last night my flash rom forgot the data format so now can not boot into the operating system, locked FRP, can not enter the TWRP.
Hello, I know it's been a long time. I put the issue aside for a few months as I had another phone to use in the meanwhile just wanted to let you know i Just did the procedure you described and it worked perfectly! The phone is back to life :laugh:

Categories

Resources