Hardware broken flap of touchscreen connector - Nexus 6 Q&A, Help & Troubleshooting

hi there i just manage to broke that part that kept the ribbon from the digitizer connected, and i cant find it anywhere, is there any beloved soul that could help me out? the board is fully functional, is such a waste to trash it just cause of a digitizer clap part thanks a lot

Maybe a piece of duct tape to hold it in. Lengthwise onto the cable, connect the cable, and pull on the tape a bit before sticking to the board.

Thin piece of cardboard to wedge in to hold the ribbon cable tight
Sent from my Nexus 6 using XDA-Developers mobile app

Related

DIY Docking Station with USB 2.0 lighted hub

I picked up this color changing USB hub from Radio Shack for $5 and it has a storage area that fits an HD2 perfectly.
I can't post a link so just google "Radio shack color changing 4 port hub" and you'll find it.
After looking at the nice fit I thought it would be easy to put a usb cable in the bottom of the compartment, so I could use it as a docking/charging station.
It's only held together by one screw in the storage compartment and then a couple pieces of double stick tape, so it was easy to open up. After taking it apart I held the phone next to it and marked where the USB port on the phone was using the dry marker that came with it. It had to be placed in the front corner of the storage compartment because of the circuit board directly underneath that storage compartment.
After marking it out I used a dremel rotary tool to put a hole in it, but I think a drill bit would have worked just as well. Then I put the USB jack in the hole so that it stood about a half inch off the bottom of the storage compartment. I took a sharp knife and trimmed those ring like pieces of plastic on the back of the usb jack off so that it was possible to put a 90 degree bend in the cable to fit it in the hub. Then I also put a small hole in the back edge and ran the cable out and plugged it into the hub.
It fits well with the stock rubber cover on the phone, or no cover on your phone, but I don't think it would fit very well if your case was much bigger than the stock case.
The dry marker that comes with the hub doesn't fit in the hole any longer, and you can't reach the buttons on your phone, but the button problem could be fixed by having the jack stand 1" off the bottom instead of the 1/2" I used.
Great job!!
Cool! Could you please measure the opening dimensions? I'm wondering if my HD2 in Otterbox Defender might fit inside?
Nice, if only we could get them in Australia.
Thx outstanding mod/hack. On my way to rat shack today thanks to your brilliant idea
Sent from tin can with string.

USB Port Fix

Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
KillerbawX said:
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
Click to expand...
Click to collapse
You could probably buy two new Raiders for $250! Replacement might be the best bet, as you can likely find one on Kijiji for $100 or so. If you have a local cell repair joint, give them a call, and see if they offer the replacement. It might be tricky since the USB on the Raider (as other HTC phones) is actually a special type of HDMI jack that also has USB (known as MHL).
If you're adventurous, you might track down a broken Raider and attempt a part swap yourself. I've not seen the inside of the unit, so I can't say how easy or hard that would be at any skill level...
Hope you get it fixed up!
The part is on eBay you can always try to do it yourself should be a few small solder points
Sent from my HTC PH39100 using xda premium
KillerbawX said:
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
Click to expand...
Click to collapse
A friend needed this. We ordered one off ebay ( http://www.ebay.com/itm/OEM-USB-Pow...328529?pt=PDA_Accessories&hash=item27c422a1d1 ) and although it required opening the phone up and voiding the warranty, it required no soldering. He doesn't open electronics up very often, and said it wasn't very hard to do.
i was babbling abt this in a thread in the dev forum, thot i'd best do it also here in the proper forum for it:
i changed the USB port in my Raider, was very simple. Six little screws, two different lengths so keep track of them. One screw also holds down the teeny cover under which is where the tiny connector resides that connects the port to the fone circuit board. Once the fone is back together that's where you make the final connection between port and fone.
Slip off the battery cover, undo the six screws, take off that tiny little cover. Carefully work off the entire back housing. There's no front housing, just the screen glass and the fone circuitry bundled together.
Micro-USB port and ribbon connector is fastened to the housing with two more of those little screws. Change out the port with the new one. New part may not be an exact duplicate of the old part: that's ok. Reassemble the fone. Under that hole left by the tiny cover, press home the miniscule plug that connects up the port to the fone.
Put back the tiny cover, fasten back all the screws, and you're done. Port cost me $9 USD plus shipping on ebay.
lowfatmilk said:
i was babbling abt this in a thread in the dev forum, thot i'd best do it also here in the proper forum for it:
i changed the USB port in my Raider, was very simple. Six little screws, two different lengths so keep track of them. One screw also holds down the teeny cover under which is where the tiny connector resides that connects the port to the fone circuit board. Once the fone is back together that's where you make the final connection between port and fone.
Slip off the battery cover, undo the six screws, take off that tiny little cover. Carefully work off the entire back housing. There's no front housing, just the screen glass and the fone circuitry bundled together.
Micro-USB port and ribbon connector is fastened to the housing with two more of those little screws. Change out the port with the new one. New part may not be an exact duplicate of the old part: that's ok. Reassemble the fone. Under that hole left by the tiny cover, press home the miniscule plug that connects up the port to the fone.
Put back the tiny cover, fasten back all the screws, and you're done. Port cost me $9 USD plus shipping on ebay.
Click to expand...
Click to collapse
Hey, dude, I know this thread is a little old, but can you PM me the link to where you bought your USB port? I think I need to replace my port (issues connecting to PC and charging requires wire wiggling), but I've read about certain ports not working with data transfer and only charging, and I don't want to make that kind of mistake.
projectisaac said:
Hey, dude, I know this thread is a little old, but can you PM me the link to where you bought your USB port? I think I need to replace my port (issues connecting to PC and charging requires wire wiggling), but I've read about certain ports not working with data transfer and only charging, and I don't want to make that kind of mistake.
Click to expand...
Click to collapse
Try this? Says OEM so I imagine you wont lose functionality.
http://www.globaldirectparts.com/product-p/htc747235-qs.htm
Thank you! And only $8 too
Sent from my Vivid 4G using xda app-developers app

Parting out Nexus 7

Hey guys, I'm considering parting out my nexus 7 because its digitizer is partially broken. I was just wondering if you guys have a need for any of the parts, and what you would pay for them. I'm not selling the parts yet, just getting an idea of if its worth my time to do so. Thanks!
I'll take the back cover for $10 shipped to Miami.
Sent from my Nexus 7 using xda premium
lamboboy732 said:
Hey guys, I'm considering parting out my nexus 7 because its digitizer is partially broken. I was just wondering if you guys have a need for any of the parts, and what you would pay for them. I'm not selling the parts yet, just getting an idea of if its worth my time to do so. Thanks!
Click to expand...
Click to collapse
I'll buy the LCD flex cable (photo below). I'll offer $10 incl mailing it to St Louis.
It's the little short cable that pops off the main board - it's located in a small gap between the battery and the main board.
You have to be very careful with this cable as the LCD end is damaged very easily. Do not pull on it at all.
To remove it, you have to
-remove the battery,
-remove all the small screws holding in the sub chassis - unscrew the speaker
-pop off the upper connector - it just pops straight up - do not pull on the cable though
-remove the digitizer cables - flip up the white cable clamps at the rear of the 2 connectors
-remove the subchassis - you'll have to remove the copper heatsink that is taped to the back of the LCD
- flip up the black cable clamp on the rear of the LCD flex connector and carefully slide the connector straight out without bending it up at all.
Let me know if you're interested.
Thanks
Thanks for the replies. Ill let you guys know it I'm going to sell the parts.

[Q] Damaged a ribbon cable plug when replacing screen, now what?!

Hi all,
I almost perfectly repaired my HTC One M7 but whilst taking it apart some tape snagged on one of the connectors and ripped the cable out of the snap/pop connector. I have some high res pics here, best I could do...
http://imgur.com/a/VVCrR
I think all but one ofthe pins are there, but some are pushed down so the cable can't split them to fit inbetween. I can't find a magnifying glass to try and part them carefully at the mo but will look tomorrow.
If I can get them apart and get the cable to fit I imagine I could solder a wire or somehow get the missing pin to connect?
Any ideas?

Magnetic charging port broken - pins fell out [Solved]

I bought a DK48 dock to charge my Z3 Compact as I did not want to faff around with the usb port cover.
After docking and undocking about 5 times the charging pins fell out. They were held on with doubled sided tape which clearly is not up to the task.
After reading an old thread and poll I do not want to send it to Sony as it should be an easy fix and not worth the time and money for them to stick it back on with some more tape.
Does anyone know how the internal pins should look? They do not appear to be symmetrical on my phone and I am concerned that they are damaged. If I hold the pins into the phone with a magnetic charging cable the phone does start to charge but If I go ahead and superglue/araldite the pins back in I might not get a good contact and then theres no going back.
What do you guys think would be the best way to fix the charging port?
Thanks in advance.
As a follow-up, I used Loctite Hybrid Glue to glue the pins back into the phone.
1. Prepare the surfaces by cleaning them with a cotton bud.
2. Apply a small amount of water to the surfaces to active the glue.
3. Apply a small amount of glue to the back of the pins being careful to not coat the contact blades.
4. Inserted the pins into the phone whilst connected to a charging cable and held it in place with an thick elastic band.
5. Waited a full 24 hours for the glue to set and now the charging port is solid.
Thanks to polar_bay for recommending the glue and method.
When I tested for a hermetic seal using GPS Status or Barometer+ to check the pressure reading I got a much more positive result (+0.4hPa) than I did before the pins came out. So that suggests the phone is now more waterproof than it was before.

Categories

Resources