HTC Power button broken + USB Cable not detected by the PC - One (M7) Q&A, Help & Troubleshooting

Hello,
My name is Adrian and i have a problem with my HTC One Mini.
Two weeks ago i dropped the phone on the ground and the part where the power button is situated broke so i had the "smartest" idea to stick it back with super glue. When i did that i managed to glue my power button at is now was not working so i thought that i should try and separate the button from the sensors and i kinda broke it worse, now i brooked the sensors it's torn and i cannot power up the phone. Since then i managed to keep my phone charged so it could not lock, so that i should have not been forced to use the power button but yesterday my battery drained out so now the phone is dead. I managed to charger it and now it's says 100% .. but the cable is not recognized by the PC and i am not able to perform the actions that i have read above "volume down + home + USB cable in", etc... What do you recommend me to do please?
Thank you in advance!

Please someone, can help me????? Thank you!
Adrian1206 said:
Hello,
My name is Adrian and i have a problem with my HTC One Mini.
Two weeks ago i dropped the phone on the ground and the part where the power button is situated broke so i had the "smartest" idea to stick it back with super glue. When i did that i managed to glue my power button at is now was not working so i thought that i should try and separate the button from the sensors and i kinda broke it worse, now i brooked the sensors it's torn and i cannot power up the phone. Since then i managed to keep my phone charged so it could not lock, so that i should have not been forced to use the power button but yesterday my battery drained out so now the phone is dead. I managed to charger it and now it's says 100% .. but the cable is not recognized by the PC and i am not able to perform the actions that i have read above "volume down + home + USB cable in", etc... What do you recommend me to do please?
Thank you in advance!
Click to expand...
Click to collapse

Related

Broken Power Button

Hello!
I accidentaly dropped my S730 on the ground, from ~2 meters, the power button broke, but the phone was still on!
But the battery lost charge and I was nowhere near a wall outlet.
I can't start the phone!!
Is there any key combination or someway to start the phone WITHOUT using the powerbutton?
Maybe some USB stuff or something?
The phone is chargine fine.
I tried sticking something else in the power "hole" but the phone refuses to start.
Please xda, help me!
http://yfrog.com/0rimg1528lj <- Picture of the severe damage.
EDIT!!
HAHA!! YEEES!
I found out a way to start it!
Press both "soft buttons" and insert a USB cable!
Then press everything else than "SEND", because that will manufacture reset the device!

Is my Kaiser dead?

Hi, recently my extUSB broke down, so I was unable to coonect anything. My friend changed the connector in proffesional way with IR gun. But now Kaiser won´t even boot up, no vibration on startup, only green LED is lit up.
I bought D2, but I am curious if there is any way to fix it.
Thanks in advance
What does your friend say?
What happens if, while holding down the camera button (on the same side as the power button but further down), you press the power button to power it on - do you get a stripy screen? If you do, you can poke the stylus into the reset hole to reset the device out of the bootloader screen. What did the friend have to say about it - personally I'd much rather have a TyTN II which boots and works fine except for a broken USB port (I presume it was working fine before the 'repair'), than one with a shiny new port that won't work at all.
Nothing happens it looks like it is absoluttely dead.
The USB port was faulty, that was reason, why I let it change.
Well, it is strange, but actually I am very satisfied with with D2, even more than with Kaiser...
Well I suppose you could always get an expert to look at it but if its motherboard is damaged (or there's other hardware damage), it may be more expensive to repair than it's worth. You could see what your local HTC people have to say about it.
Flying Kiwi said:
Well I suppose you could always get an expert to look at it but if its motherboard is damaged (or there's other hardware damage), it may be more expensive to repair than it's worth. You could see what your local HTC people have to say about it.
Click to expand...
Click to collapse
Or you could sell it in the market section, plenty of people that would like to get a crack at fixing it or use it for parts.
Hi, I just encountered the very same issue. I know I'm ressurecting a very old thread, but I rather do this than creating a new one
I flashed my Kaiser with Android about two months back. Everything was quite stable, no hardware issues. Suddenly, it won't turn on.
When I plug a charger in the extUSB, the orange LED won't show up. And if I try to turn on the phone, the green LED shows up and stays solid. However, the short familiar vibration isn't there and also the screen remains black. Nothing was wrong with the USB port. I tried multiple chargers...
janys said:
Hi, I just encountered the very same issue. I know I'm ressurecting a very old thread, but I rather do this than creating a new one
I flashed my Kaiser with Android about two months back. Everything was quite stable, no hardware issues. Suddenly, it won't turn on.
When I plug a charger in the extUSB, the orange LED won't show up. And if I try to turn on the phone, the green LED shows up and stays solid. However, the short familiar vibration isn't there and also the screen remains black. Nothing was wrong with the USB port. I tried multiple chargers...
Click to expand...
Click to collapse
Have you tried to reflash or hard reset?. Also maybe your battery is gone..try another one.
Some things to try
janys said:
When I plug a charger in the extUSB, the orange LED won't show up. And if I try to turn on the phone, the green LED shows up and stays solid. However, the short familiar vibration isn't there and also the screen remains black.
Click to expand...
Click to collapse
I realise you cant flash if it's not booting but if your battery has sufficient charge remaining (won't work if it's flat) it'd be worth trying a hard reset using the D pad key + stylus in the hole method (can be done at switch on time without needing a full boot).
Nothing was wrong with the USB port. I tried multiple chargers...
Click to expand...
Click to collapse
How do you know that a fault hasn't now developed with it - I wouldn't rule that out at this stage. Have you tried a known good battery that is fully charged in the phone also is it the original charger you are trying (not all chargers with the same plug are compatible)? Are you able to get the bootloader screen to show and if so, what does it display?
Flying Kiwi said:
I realise you cant flash if it's not booting but if your battery has sufficient charge remaining (won't work if it's flat) it'd be worth trying a hard reset using the D pad key + stylus in the hole method (can be done at switch on time without needing a full boot).
How do you know that a fault hasn't now developed with it - I wouldn't rule that out at this stage. Have you tried a known good battery that is fully charged in the phone also is it the original charger you are trying (not all chargers with the same plug are compatible)? Are you able to get the bootloader screen to show and if so, what does it display?
Click to expand...
Click to collapse
No bootloader, no nothing - just black screen (there's not even a hint of backlight). I'll try a different battery today.
I tried using my old AC charger, my colleague's AC charger (for TouchPRO2), USB cable... the orange LED still doesn't come up.
What's the hardreset using Dpad key? I tried holding the power button + camera and also holding the two "context" keys (above explorer and messages buttons) and touching the reset button with the stylus.
I'll see whether a different battery will do the trick.
Thanks a lot for all your suggestions, guys! Much appreciated!
janys said:
No bootloader, no nothing - just black screen (there's not even a hint of backlight).
Click to expand...
Click to collapse
What's the hardreset using Dpad key? I tried holding the power button + camera and also holding the two "context" keys (above explorer and messages buttons) and touching the reset button with the stylus.
I'll see whether a different battery will do the trick.
Click to expand...
Click to collapse
The context key one you mentioned is what I refer to as a D Pad hard reset. The one where you press the power button while already holding down the camera button is how to get into the boot loader - it's all explained in the Kaiser wiki. Sounds like another battery is definitely worth a shot - especially if you only have one (I have 3 for my Kaiser and on some days with heavy GPS use, I need all of them). What happened between it working and not working - what were you installing or doing with it?
Flying Kiwi said:
The context key one you mentioned is what I refer to as a D Pad hard reset. The one where you press the power button while already holding down the camera button is how to get into the boot loader - it's all explained in the Kaiser wiki. Sounds like another battery is definitely worth a shot - especially if you only have one (I have 3 for my Kaiser and on some days with heavy GPS use, I need all of them). What happened between it working and not working - what were you installing or doing with it?
Click to expand...
Click to collapse
I tried another (fully charged) battery from my gf's Kaiser today. No change. When I press the power button, the green LED shows up and stays solid (no blinking/flashing). Screen is black, no short vibration. I tried all sorts of hardresets and also tried to get into the bootloader. No luck.
Also, I took my multimeter and measured voltages on the charger, the battery and the pins in the phone where battery resides. Everything seemed to give a correct voltage. So it's really not a power issue
Thanks for all your help, but I'm afraid I have a total brick in my hand.
My Kaiser
Hi I have a HTC Kaiser I bought the first week it came out and it was f=ine for quite a while but 6 months ago it stopped working. It'll go to bootloader but won't flash. When trying to turn it on it'll go and just get stuck on the splash screen. I figured it was a battery because I'm very hard on my phones but I just got a replacement battery last week and all 3 of my batteries act the same way. I may have been trying to flsh went it went down it was a few months ago so I can't remember.
--- Other things to note
My Kaiser got wet and I had to have the usb port replaced and the dpad replaced. The usb acts fine but the middle dpad button does not work
The charging light will stay orange or green after I unplug the charger
After reading for the last week I think its either bricked or maybe has a bad hardspl on it?!?
Thanks in Advance for any help you guys may give.
jaygriggs said:
My Kaiser got wet and I had to have the usb port replaced and the dpad replaced. The usb acts fine but the middle dpad button does not work
The charging light will stay orange or green after I unplug the charger
After reading for the last week I think its either bricked or maybe has a bad hardspl on it?!?
Click to expand...
Click to collapse
Time for it to visit the same phone repair shop (or HTC) again for an assesment/possible repair if economically viable. If it's only recently got wet, you may be able to catch it before corrosion sets in and causes any damage but if it's not dryed out/cleaned quickly, the damage (from the resulting corrosion) will eventually show up (possibly in all the ways you've described).

[Q] i9000 bricked?

Hi guys,
i cant switch on my phone at all. 3 combo button cant work too. my phones dead except for charging.
history of my phone:
replaced screen.
power button ribbon was damaged while replacing screen.
so i bought a new ribbon to solder it on.
i was using the phone without the power button while waiting for the power button ribbon to arrive.
one day my phone just went to a black screen and thats that. i cant even power on my phone now.
just soldered the power button ribbon back. still not working.
any help guys???
Just read this....CLICK ME
Maybe it can help identify whether there is something else wrong with your phone or if your power button is still not working
Also there was a thread i believe in Q&A a while back where someone had broken his/her power button. So try the search again... GL

[Q] Power button broken

HI there!
Im now on XDA (as you can tell)
My SXL has a broken power button and i was wondering how can i turn it on?
Thanks
repair,,,
alexfadhili2 said:
HI there!
Im now on XDA (as you can tell)
My SXL has a broken power button and i was wondering how can i turn it on?
Thanks
Click to expand...
Click to collapse
I have the same issue with my SXL and here is what I do ..
1. Use CWM Recovery (Search the forums) - it will switch on your phone on connecting it to with a charger/USB cable. This comes in handy if I remove the battery and since the power button does not work at all, I cannot power on the phone in any other way. Once I plug in my switched off SXL, CWM Recovery starts up the phone and I get to reboot it from Recovery.
2. USe a custom ROM (I would recommend CodeFireX from Anders if you like 4.2.2 or RunnyKitKat from Onejay for 4.4.2) and under settings get the volume to wake feature turned on. Now you can wake the phone screen using the volume buttons.
3. Get an app from the Play Store - "Reboot Menu widget", which becomes a soft menu button to reboot or shutdown, or take a screen shot or to simply close down the screen...
I couldn't get my power button fixed as the device was out of warranty and I did not want to spend the exorbitant prices these guys were asking. So that's what anyone with a broken power button can do.. Hope this helps
jib_intelli said:
I have the same issue with my SXL and here is what I do ..
1. Use CWM Recovery (Search the forums) - it will switch on your phone on connecting it to with a charger/USB cable. This comes in handy if I remove the battery and since the power button does not work at all, I cannot power on the phone in any other way. Once I plug in my switched off SXL, CWM Recovery starts up the phone and I get to reboot it from Recovery.
2. USe a custom ROM (I would recommend CodeFireX from Anders if you like 4.2.2 or RunnyKitKat from Onejay for 4.4.2) and under settings get the volume to wake feature turned on. Now you can wake the phone screen using the volume buttons.
3. Get an app from the Play Store - "Reboot Menu widget", which becomes a soft menu button to reboot or shutdown, or take a screen shot or to simply close down the screen...
I couldn't get my power button fixed as the device was out of warranty and I did not want to spend the exorbitant prices these guys were asking. So that's what anyone with a broken power button can do.. Hope this helps
Click to expand...
Click to collapse
Thank You very much that solved my problem!
Didnt want to get it fixed they charge to much
Thank You Again:victory::victory:
Hi
Power button and volume buttons are identical with buttons used for HD2.
HD2 buttons are attachable, there is 5 of them and they are very cheap.
Get them and find someone with soldering gun with thin tip (for smd) who could solder them for you.
jjaagg said:
Hi
Power button and volume buttons are identical with buttons used for HD2.
HD2 buttons are attachable, there is 5 of them and they are very cheap.
Get them and find someone with soldering gun with thin tip (for smd) who could solder them for you.
Click to expand...
Click to collapse
Cool thanks for telling that, now i just got to find someone with an HD2 LOL.
90% of people i know have iphones, so thats going to be hard :fingers-crossed:
Search for some combination of these words on ebay and replace the main board. It's usually the little micro-switch that's gone so replacing the plastic button doesn't do anything.
HTC Sensation XL Main Ribbon Board Flex Mute Button Power Volume Cable G21 X315
gnscon said:
Search for some combination of these words on ebay and replace the main board. It's usually the little micro-switch that's gone so replacing the plastic button doesn't do anything.
HTC Sensation XL Main Ribbon Board Flex Mute Button Power Volume Cable G21 X315
Click to expand...
Click to collapse
Button is located (soldered) on the board and is covered with protective tape.
When broken usually only plastic body stays on board. Transparent cover (with black dot) and micro disk comes off and for that reason button does not work. Whole plastic button needs to be unsoldered and replaced.
I attached picture of HD2 buttons which you can buy i.e on ebay.
I did it twice (first time with volume then with power button) and it costs nothing.
Replacing whole board is quite expensive and unnecessary - in my opinion.

Broken power button.

Hi! I'm having problems with my GT-I8190L the "power" button stop working some days ago. The cellphone was working ok but yesterday the battery discharged to zero and the cellphone was turned off.
After that I cant't turn on the cellphone. The battery is full charge now.
- I tried with this video youtube (dot) com watch ? v=l402ljcmPu4
- Also I disambled the phone following this guide formymobile (dot) co (dot) uk /i8190disassembly.php and I cleaned the phone with isopropyl alcohol.
- I also plug the cellphone to my computer an adb is not seeing it.
Nothing worked....
- The button is not stuck. Y can press it and fell the feedback.
- When I plug the power charger I can see the "battery logo" and the baterry is charged.
Any hint on how to turn it on?
Is possible to replace the power button?
Thanks to all!
PS: I was using cyanogenmod 11 by NovaFusion team.
URGENT!! Same to me!!
Hi, I'm having the same problem with the Power Button! I can feel it pressing, but no response.
Does anyone know how to solve it?
I'll appreciate the help!
gilgamezh said:
Hi! I'm having problems with my GT-I8190L the "power" button stop working some days ago. The cellphone was working ok but yesterday the battery discharged to zero and the cellphone was turned off.
After that I cant't turn on the cellphone. The battery is full charge now.
- I tried with this video youtube (dot) com watch ? v=l402ljcmPu4
- Also I disambled the phone following this guide formymobile (dot) co (dot) uk /i8190disassembly.php and I cleaned the phone with isopropyl alcohol.
- I also plug the cellphone to my computer an adb is not seeing it.
Nothing worked....
- The button is not stuck. Y can press it and fell the feedback.
- When I plug the power charger I can see the "battery logo" and the baterry is charged.
Any hint on how to turn it on?
Is possible to replace the power button?
Thanks to all!
PS: I was using cyanogenmod 11 by NovaFusion team.
Click to expand...
Click to collapse
I have an idea that may or may not work but give it a try:
1. Press and hold volume up and home button.
2. While holding these buttons (step 1), plug your phone into a charger and make sure that it is connected to an outlet
3. Keep holding the buttons until the logo appears
From there you can either install TWRP via ODIN which will allow you to navigate without buttons or alternatively choose not to go into recovery and the phone should reboot
I'm assuming that you know what I'm referring to as you already had a custom ROM installed
Never tried italics before but I've just done it on my S3 mini running TWRP
Good luck

Categories

Resources