Hi, I cleaned the screen of my HTC Diamond with a bit of alcohol and a pice of tissue and it seems that the alcohol got inside of the Power button. Now, every time I try to turn the screen on by touching the power button, it turns the screen on but it dispays a message that says: "Warning: Power will be turned off and you may lose data if you have not saved them. Do you want to continue?"
If I click YES, it reboots the phone, If I click NO, then its ok. That is fine, but the problem is when I want to turn the phone off. It's impossible. It will keep trying to reboot.
Does anybody know what can I do? I am really worried.
One solution could be to make some other button from the phone to act as the power button (like the Home button that is rarely used). How can I do that?
Please help!!!!
Thank you
Hi,
I have the same problem.
Did you already find an answer ?
No, I didnt find the solution. I tried to fix the hardware but didnt succeed. So, I created a dummy file to emulate the poweroffwarning.exe that pops up when you long press the power button.
Solution
Hello, I have one AT&T TITL 8925 that upgraded to Windows Mobile 6.5
After the new software was loaded I saw same behavior on my phone.
When the phone is ON and I pressed the power button sometimes it do not respond, and others I received the warning message "power will be turned off and you may lose data if you have not saved them..." My first tought was that it is because the processor is slow to this new software release, or maybe my phone is damaged. I was working perfectly with previous (light version) release so my final guess is that this sw requires more uses of the processos.
Anyways what I have been doing is before turing it off I press the red button or hang up button, and after this if I press the power button it works fine (No more warnings). I have some theories but I will keep doing the same
Hope this partial solution helps you as it does for me.
Regards
Jerry
this is not working for me :| the problem is i can't use my power button not even to open my display when it goes to sleep :|:| i don't know what to do guys please help me
You can use the Stylus to awake the phone, instead of using the power button. You can also use TouchLockPro, to suspend the device, so you do not need the power button for that too.
Also you can set the phone to awake on pressing any key (Windows Mobile Setting), but be sure to have a good locking tool, which makes sure you do not have bogus calls and it goes to sleep again fast enough, otherwise it will drain battery.
I have the same problem.
Anyone solved this one?
I have the same issue and this is not a hardware problem. Strange since even updates/changes of the rom do not correct the issue. Did anybody find a solution for this...?
Well.. ive had this problem just ones.. I was walking downtown with my diamond in the frontpocket of my jeans (face down), after about 3min. of walk, it started to rain (big drops), and my clothes got completely wet, i turned around emidietly, to walk back to home. When i got home after 3 more min. i layed the phone on the table, and then i could hear there were somethibg wrong.. The "turn off" sound came, and the notification kept on coming up, even though i pressed No, as if i were just holding the power button down.. Then i began to press the power button continuesly for about a 100 times, and to my surprise then it stopped and have functioned perfectly for about 2 month now.. Something tells me theres some serius promlem with the smallest kind of moisture near the power button on this phone..
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
[ElCondor] said:
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
Click to expand...
Click to collapse
Hi! on one of my diamond, the power button off from the board. So the black little board with the button itself is not part of the complete circuit anymore... if someone know the hw testpoint for that it would great please.... i see a few TP around, but if i just start sorting them i just going to kill it...I use to flash phones with TP so is not new for me , but i find nothing for diamond.
I have a similar issue. Mine seems like it is almost stuck on, so it wakes its self up all the time, meaning a full charge lasts an hour or two. Then when it runs out of battery it tries to switch itself back on, so goes through a continuous cycle of vibrating and beeping until the battery is removed. The gf finds it very annoying at 3am lol.
Don't recall mine getting wet, but it's possible it could have got damp at some point, but it's been doing this now for about 3 weeks.
Tried a hard reset with no luck.
[ElCondor] said:
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
Click to expand...
Click to collapse
I can see that how to remove the power button from the video showing how to replace the screen. Any idea if once removed the button can be fixed, if not can you get replacements?
2004mark said:
I can see that how to remove the power button from the video showing how to replace the screen. Any idea if once removed the button can be fixed, if not can you get replacements?
Click to expand...
Click to collapse
I think I should send it to HTC, and ask them to do it. Or go to a repair centre. But I should not try it myself, because it can be dangerous for the diamond.
Also try searching on ebay, there might be the parts you could use.
Good luck!
is there a way to remap the power button?
my diamond face same problem since this afternoon, arrrrgghhhh!!!
- blocking hwbutton1, hwbutton2, hwbutton3, hwbutton4, hwbutton5, hwbutton6, hwbutton7 >>>> NO LUCK
- hard reset >>> NO LUCK
guys, any of you solved the problem yet
youtube.com/watch?v=Q4SEQ6AUFOI
My Sony X1 have some strange problems with the power button. When it goes into sleep mode, I can not wake it up with the power button, all I can do is to soft reset. Sometimes it does not go into sleep mode either , it just "wake up" all the time. I don't know what's wrong with it, tried Hard reset but no use .
ANyone had this problems before?
@
The only way to solve this is to leave the phone near your laptop heat vent ( fan) . hot air from it might help you to get the power button up and running. But if that to doesn't work then i'm afraid thats bad.
Current sol :
1. download SU2U ( search threads )
2. go to the settings and make the " lock when stylus inserted" option ON
3. Change the screen turn off time to 5 secs..
So , to unlock , remove stylus , to lock -> insert it back ( its turns off the back light within 5 sec )
Less annoying
elektros said:
youtube.com/watch?v=Q4SEQ6AUFOI
Click to expand...
Click to collapse
thanks for this link, i accidentally tear off my power button flex. now i could turn it on again. Thanks elektros
hi,
yesterday I disassembled my phone to fix a microp error that had occured when i had dropped my phone. i disconnected two cables (one for the keyboard, the other for the lcd screen). then i reconnected them both and then went about reassembling the phone. however I accidently ruined the power button of the phone when i was doing so. a little part of the power button came off (a black button with the black sticky tape).
when i connect my phone to a charger and the enter button shows a pulsing light indicating it is charging.
so i was wondering does anyone know how to fix the power button for the htc diamond, does it require any minor soldering? or is it possible to turn my phone on any other way so that i can assign a different key to act as the power button.
cheers.
You can turn the phone on by using the soft reset hole on the bottom with the stylus.
dwizzy130
did it fix the microp error? if so how?!
Hi guys,
i cant switch on my phone at all. 3 combo button cant work too. my phones dead except for charging.
history of my phone:
replaced screen.
power button ribbon was damaged while replacing screen.
so i bought a new ribbon to solder it on.
i was using the phone without the power button while waiting for the power button ribbon to arrive.
one day my phone just went to a black screen and thats that. i cant even power on my phone now.
just soldered the power button ribbon back. still not working.
any help guys???
Just read this....CLICK ME
Maybe it can help identify whether there is something else wrong with your phone or if your power button is still not working
Also there was a thread i believe in Q&A a while back where someone had broken his/her power button. So try the search again... GL
Hello guys,
so I woke up this morning and found my phone lying on the floor still connected to the charger. When I tried to unlock the screen everything was phone, but when I tried to relock the screen it kept popping up the power menu. Also I noticed that the powerbutton had moved a bit more to the inside of the phone. Sometimes it turns off the screen but immediately after turns it on again. I can turn the phone off but it will instantly reboot.
Any solution? It's kinda a pain in the *** that I can't switch off the phone...
Thanks in advance
fix
The same thing happened to me last week i was very pissed of. Then i tryed the safetypin and itr worked. So what you do is remove the button but making the safety pin go in the small gaps of the powerbutton and then pull it out. If it is not damaged to much just put according to your need so all the functions work. Another fix is get a new power button and put it in the power button hole it should work now. If this helped please hit the thanks button
Hello,
My name is Adrian and i have a problem with my HTC One Mini.
Two weeks ago i dropped the phone on the ground and the part where the power button is situated broke so i had the "smartest" idea to stick it back with super glue. When i did that i managed to glue my power button at is now was not working so i thought that i should try and separate the button from the sensors and i kinda broke it worse, now i brooked the sensors it's torn and i cannot power up the phone. Since then i managed to keep my phone charged so it could not lock, so that i should have not been forced to use the power button but yesterday my battery drained out so now the phone is dead. I managed to charger it and now it's says 100% .. but the cable is not recognized by the PC and i am not able to perform the actions that i have read above "volume down + home + USB cable in", etc... What do you recommend me to do please?
Thank you in advance!
Please someone, can help me????? Thank you!
Adrian1206 said:
Hello,
My name is Adrian and i have a problem with my HTC One Mini.
Two weeks ago i dropped the phone on the ground and the part where the power button is situated broke so i had the "smartest" idea to stick it back with super glue. When i did that i managed to glue my power button at is now was not working so i thought that i should try and separate the button from the sensors and i kinda broke it worse, now i brooked the sensors it's torn and i cannot power up the phone. Since then i managed to keep my phone charged so it could not lock, so that i should have not been forced to use the power button but yesterday my battery drained out so now the phone is dead. I managed to charger it and now it's says 100% .. but the cable is not recognized by the PC and i am not able to perform the actions that i have read above "volume down + home + USB cable in", etc... What do you recommend me to do please?
Thank you in advance!
Click to expand...
Click to collapse