Hi, I have been using my HTC diamond toch for nearly 2 1/2 months. a few days ago, i did a rom update using Dutty's rom update. All went fine duing the update. used the phone for about 5 days nonstop, no issues at all.
But yesterday all of a sudden the phone has swtiched off by itself, now it doesn't switch on. Thought the battery might be dead so i tried charging but the enter buttton area doesnt glow and there is no sign of charging.
I switched batteries with a friend to see whether it was faulty but it is in good condition.
What do u think the issue will be ?
Thanks
Buddhi.
I have the same problem. I've just got my phone back from being repaired as the touch screen got all messed up and now it won't charge. I plug it in and the touch pad does the charge animation twice then stops. It'll randomly try to turn on but it doesn't even get to the point where the red writing apears before it turns off again.
Help?!
same problem here
Dudes.... Chill!!!!
Here's what you can all try ....
First you guys need to know that de HTC does not charge if the rom is inconplete/damaged .
And.....
If your batery is realy dead there is no initial power on the internal battery to manage the chargement.
So ... resolution.
Fist way .
If you know any one that may have an other HTC Diamond you need to swamp batteries so the good Diamond that has the internal bat ok and charge it there.
Second way . this one i did it my self .
Go to a Local ChinaMan store and buy a multimeter and a regular Universal Adapter.
Heres how it hoes ...
Use the Multimeter do figure out the polarity pin's on the battery ex: + and - .
remove / cut one of the plug's from the Universal transformer and also tag the polarity.
set the voltage to be close to 5 V - 1 Amp .
Can be 4,5v or 5.5v no sweat
Conect the cuted wire from the Univ. Adapter to the Diamond Battery respecting the polarity.
Leave it for a wile..... ( Probably up to 1 hour but chec from time to time tme battery temperature and if possible a reading on the bat voltage levels.)
Done!
Put the battery bat and boot your diamond or turn on to boot loader.
**** Attention if you don't have more than 50% of the bat charge compleated you wont be able to flash your phone****
Any questions Just reply back.
same problem...
its just...my battery was full before the upgrading...i was Unlocking my Diamond..and the upgrade didnt move more than 0% just when i looked on my mobile...there was black screnn...pluged it out..tried to power on..nothing..tried to charge...nothing again..i tried hard reset(vol down+power+back+reset)..it just wont turn on..please help me..im in panic
Help, I have the same problem and my battery was fully charged before this happened. Voltage reading is 4.2V on the battery.
I also tested the power button and there is nothing wrong with it, it conducts when pushed.
Usually pluging in the charger should start it up, but it will not start.
Anyone have any solutions?
I couldn't fix mine so phones 4 u replaced it with a touch hd
Mattmanico said:
I have the same problem. I've just got my phone back from being repaired as the touch screen got all messed up and now it won't charge. I plug it in and the touch pad does the charge animation twice then stops. It'll randomly try to turn on but it doesn't even get to the point where the red writing apears before it turns off again.
Help?!
Click to expand...
Click to collapse
I had the same exact problem two days ago.The phone was not charging while it was on,and when it was off it did that charging light animation twice and then third time the litght managed to get in the middle of the button and sudennly stopped. So here is my solution . I'v managed to charge the battery on another phone and turned my Diamond back on. While still attached to charger and power source i'v performed a soft reset (by pressing the reset button beneath the stilus) ...the phone reseted and now it's all ok.
bughiman99 said:
I had the same exact problem two days ago.The phone was not charging while it was on,and when it was off it did that charging light animation twice and then third time the litght managed to get in the middle of the button and sudennly stopped. So here is my solution . I'v managed to charge the battery on another phone and turned my Diamond back on. While still attached to charger and power source i'v performed a soft reset (by pressing the reset button beneath the stilus) ...the phone reseted and now it's all ok.
Click to expand...
Click to collapse
I had same problem , no solution yet.
When I had a Mpx220 I had fixed changing a fuse, but I can´t see nothing in internet guides or foruns.
If someone knows how to repair tell us, becouse htc service in our country isn´t good and my device is outdate warranty.
Regards,
Gus
Someone has fixed?
I have the same problem but on my samsung corby GT-i5500. I installed the clockworkmod on my mobile by rom manager and rebooted in recovery, I think i've installed a wrong version and now it does not turn on at all! what should I do? my parents will kill me if they discover that ive broke my phone
So the phone will not turn on until I remove the battery, reinsert the battery ( I get a white circle in the center of the display) then hurry and plug in a usb cable to get the battery icon to display. then the phone will power on.
When the phone is completely off and I insert a usb cable I never get a battery icon stating that the unit is charging. I have replaced the battery and the usb cable.
when the phone is completely off and I know I have a good charge on the battery, it will not power.
I recently flashed the phone to stock to see if any boot loaders, kernels, etc might be the - cause same issue. I am back to being rooted and running ics.
the phone will reboot without issue.
just once the phone is completely off is when I run into this issue.
today the phone shut off (with 95% on the battery) and the circle in the center of the display was flashing on and off - to me it seems that the battery was not securely seated - I went through my ritual and the phone powered on without issue.
The battery contacts are intact and move as they should when the battery is inserted so I know there is good contact.
I hope someone can point me into the right direction.
THanks!!
.....Nm. Sorry :/
Sent by XDA Premium App
Update - I can turn the unit on when the screen is facing the ground. lol.. i am at a loss
Hello:
I recently got a use Bionic with a cracked screen, no battery, and no sim card. I replaced the screen and bought a non-oem extended battery with cover. When I got everything and fixed it, the phone worked for 3 days. During this time I did a factory reset plus cache wipe then updated everything to latest software and firmware. I had it plugged into my computer to charge over night but on the third day after being plugged in to the computer to charge, I tried to turn on the phone and the white light started blinking at me. I had a wall charger that I use for my Samsung Galaxy Precedent (current using phone) to charge it over night again but all I would get is the Motorola M logo and a then the battery charge status. I search some forums and some one said that my battery was bad so I got an OEM extended battery and an OEM wall charger with dock station. So at this point, the only thing I can access is the recovery screen but that only happens when it is pugged into the wall charger but when I hit the power button I get the Motorola M logo and the battery status which say 5%. Once the screen goes dark again I hit the power button and the battery says 100%. But once I unplug it, I get nothing. Not even the recovery screen. When I plug it into my computer I get the white light again but this time it stays solid. It still will not power up, or even access the recovery screen while plugged into the computer as well. Any suggestion on what might be wrong and what I might do to fix it? Please help someone!
Hey, I dropped my atrix hd flat on its face on a rug and now it just won't turn on. When I plugged in the wall charger the green charge light comes on and then the Motorola duel core boot sign comes on and the it shuts off and repeats the same process. So it constantly repeats the reboot only as far as the Motorola sign. The phone was rooted and the bootloader and the sim carrier is unlocked. It's running kit kat Ron I think was CM. When I unplugged the phone it just shuts off like I removed the battery. I will order another battery but this one is only a few months old so how can it be that or how even is it possible to ruin my phone with a simple drop? It's dropped harder before but this is just weird. Please help.
Did you do the EB40 mod?
Have you tried to go into recovery and/or bootloader mode?
Fixed
So I ordered a new battery even though I just replaced this one and come to find out that the battery has a sticker to hold the battery in place for the HD models. I guess I forgot to do it the first time changing it and when I dropped it I guess it damaged the battery ribbon. With the new battery it works fine and I made sure it is stuck. Thanks for you replies.
I've replace my battery, volume keys ( board), charge port, front chassis with screen/digitizer and back chassis. At first the battery charge icon come on but then powers onto a htc one screen and reboots. It came on but battery was dead then i got it to work by rebooting from fastboot/bootloader and it worked but when i turned it off to charge it kept rebooting? i hope the parts are not incompatible they did cost a lot. I cant get into recovery so i'm wondering if i should reflash it?
bump
BUMP
When the phone is off and you connect a charger does it come on and attempts to boot or goes to the charging screen?
starboi4eva said:
When the phone is off and you connect a charger does it come on and attempts to boot or goes to the charging screen?
Click to expand...
Click to collapse
yes, charging is stuck and actually found the problem if i take out the flex ribbon it will charge but i can't turn on obviously cos power button will be disconnected but then if i connect it while charging and power on it works. That means something wrong with the daughter board, the supplier must have given me a wrong version than the original which is why it cannot communicate... thanks for replying.
No problem man.