Hi guys i need someone to upload latest official V20C rom (open euro ita or ger) because i cant download it from LG Firmware site and the one i have when i flash it auto brightness isnt working (i checked everything is ok with hardwer just software problem prob bad copy or whatever).Thanks
Please Check HERE
These are only .kdz
Direct download ITALY
(Please refresh direct link, If download does not start OR click on link and press Enter Key)
Salman Al-Badgail said:
Please Check HERE
These are only .kdz
Direct download ITALY
(Please refresh direct link, If download does not start OR click on link and press Enter Key)
Click to expand...
Click to collapse
Thank you trick with enter helped me
dimi89 said:
Thank you trick with enter helped me
Click to expand...
Click to collapse
great :good:
InterrtuptoR said:
Unfortunately u didnt tag me xD i made a mistake when i created my name so im not interruptor xD
Iam now on v20c and things didnt change much on cm11, ril droped and nfc is buggy, nfc isnt a problem that much after a couple of restarts it works it just freezes device for less then a minute and then works, but after one reboot it worked better, it switched on/of faster, but ril dropped... i need stable ril now so im back to stock where everything works fine...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my LG-P880 using Tapatalk
Click to expand...
Click to collapse
Phil_Smith said:
Oh, nevermind: Thanks @Salman Al-Badgail
Click to expand...
Click to collapse
Salman Al-Badgail said:
great :good:
Click to expand...
Click to collapse
OK..., take time to check : LGExtract.exe -kdz V20C_00.kdz
Then just open resulting cab for .dz_verification: "LGP880AT-00-V20c-EUR-XXX-OCT-07-2014+0.dz"
If needed I can upload it.
oF2pks said:
OK..., take time to check : LGExtract.exe -kdz V20C_00.kdz
Then just open resulting cab for .dz_verification: "LGP880AT-00-V20c-EUR-XXX-OCT-07-2014+0.dz"
If needed I can upload it.
Click to expand...
Click to collapse
So you think i dont have the right v20c?
Where can i find the lgextract.exe?
InterrtuptoR said:
So you think i dont have the right v20c?
Where can i find the lgextract.exe?
Click to expand...
Click to collapse
Check here for LGExtract.exe
I am not sure if this help you or not.
oF2pks said:
OK..., take time to check : LGExtract.exe -kdz V20C_00.kdz
Then just open resulting cab for .dz_verification: "LGP880AT-00-V20c-EUR-XXX-OCT-07-2014+0.dz"
If needed I can upload it.
Click to expand...
Click to collapse
I have the same dz...
@InterrtuptoR now your main problem is about ril and nfc ??? Please confirm. Please change firmware to v20A and give a shot and let us know, also try changing SIM so that we can come to conclusion
Salman Al-Badgail said:
@InterrtuptoR now your main problem is about ril and nfc ??? Please confirm
Click to expand...
Click to collapse
Mainly ril, i dont use nfc that much...
Im on stock now and everything is fine...
Sent from my LG-P880 using Tapatalk
@InterrtuptoR For RIL you can change firmware to either v20b or v20a and also try changing sim card and please check. For bad network some time sim card that too old might create a problem, anyway give a shot and please do report so that we can see what else we can do for you. For now I am sleeping its already late. will get back to you after next 12-14hr
Thanks
Salman Al-Badgail said:
@InterrtuptoR For RIL you can change firmware to either v20b or v20a and also try changing sim card and please check. For bad network some time sim card that too old might create a problem, anyway give a shot and please do report so that we can see what else we can do for you.
Thanks
Click to expand...
Click to collapse
I was on 20b, now on 20c, will try 20a and change sim, but i think its not the hardware cause all works on stock...
If it was the sim it wouldnt work on stock, right? I dont have time now to try all that, but will report when i try...
Sent from my LG-P880 using Tapatalk
@InterrtuptoR sure give a try, Thanks
@Phil_Smith @InterrtuptoR , after many readings:
http://forum.xda-developers.com/search/thread/2780274?query=02.1233
http://forum.xda-developers.com/showthread.php?t=2329768
it looks logical that your AboutPhone/screen indicates a v20c/01.1233 firmware different from last kdz flashed...; if not : it means you used a "tricky" method to upgrade to v20c_00.kdz...
FIRST (lucky? ) remove your battery for few and reboot back to check changes in AboutPhone/screen for KitKat minimum;
CHECK BEST: http://forum.xda-developers.com/optimus-4x-hd/general/lg-p880-firmware-flash-upgrade-t2919195
(I remember I used odd ref http://forum.xda-developers.com/showthread.php?t=2069723 with v20d/02.1216.01)
@dimi89 can you upgrade this thread/title with cleared ref V20c-EUR-XXX-OCT-07-2014
Download mirror for official LG2014 v20c_00.kdz (zipped) & P880-Flashtools.rar : https://www.androidfilehost.com/?w=files&flid=128886
@oF2pks Appreciate Man for uploading .kdz This might help many users. Also upload any v10xyz for ICS stock user like a complete package.
Thanks again
oF2pks said:
@Phil_Smith @InterrtuptoR , after many readings:
http://forum.xda-developers.com/search/thread/2780274?query=02.1233
http://forum.xda-developers.com/showthread.php?t=2329768
it looks logical that your AboutPhone/screen indicates a v20c/01.1233 firmware different from last kdz flashed...; if not : it means you used a "tricky" method to upgrade to v20c_00.kdz...
FIRST (lucky? ) remove your battery for few and reboot back to check changes in AboutPhone/screen for KitKat minimum;
CHECK BEST: http://forum.xda-developers.com/optimus-4x-hd/general/lg-p880-firmware-flash-upgrade-t2919195
(I remember I used odd ref http://forum.xda-developers.com/showthread.php?t=2069723 with v20d/02.1216.01)
@dimi89 can you upgrade this thread/title with cleared ref V20c-EUR-XXX-OCT-07-2014
Download mirror for official LG2014 v20c_00.kdz (zipped) & P880-Flashtools.rar : https://www.androidfilehost.com/?w=files&flid=128886
Click to expand...
Click to collapse
First of all thanks for all your research and help!
Sadly the LG Mobile Support Tool always stops saying "Upgrade stopped due to an error".
Anything I can do?
Edit: And thinking that it might have to do with Windows version (running Windows 10 x64), I tried using a virtual machine emulating Win 7 x64, but here it says "Cannot connect to server"...
(usual at your own risks...)
Phil_Smith said:
First of all thanks for all your research and help!
Sadly the LG Mobile Support Tool always stops saying "Upgrade stopped due to an error".
Anything I can do?
Edit: And thinking that it might have to do with Windows version (running Windows 10 x64), I tried using a virtual machine emulating Win 7 x64, but here it says "Cannot connect to server"...
Click to expand...
Click to collapse
( @InterrtuptoR )
Remember that .kdz is LG' file_support for upgrade/init firmware; the good is that the Win dll/flash is included in the .kdz (better option than tricky .dz flash): check whole thread http://forum.xda-developers.com/optimus-4x-hd/general/lg-p880-firmware-flash-upgrade-t2919195
- use CSE flash with custom rom
(- OR restore a JB nandroid and then use NORMAL flash for an upgrade on JB)
If trouble :
-FIRST (lucky ?) : try another usb cable
-HARD : format via cwm and proceed http://forum.xda-developers.com/showthread.php?t=2069723
I'm pretty sure @dimi89 just went threw this; he is an early p880' user and will help for steps or different way (?)
Once done, you need to flash cwm and a custom rom to check that AboutPhone/baseband is showing exact kdz :"LGP880AT-00-V20c-EUR-XXX-OCT-07-2014" and not the version firmware 02.1233, ie a different kdz origin.
(Under resulting LG JB, the AboutPhone/os firmware indication is always the rom in use, not the original kdz, so it always looks good even if not...like old 2013 V20C or remix... )
oF2pks said:
( @InterrtuptoR )
Remember that .kdz is LG' file_support for upgrade/init firmware; the good is that the Win dll/flash is included in the .kdz (better option than tricky .dz flash): check whole thread http://forum.xda-developers.com/optimus-4x-hd/general/lg-p880-firmware-flash-upgrade-t2919195
- use CSE flash with custom rom
(- OR restore a JB nandroid and then use NORMAL flash for an upgrade on JB)
If trouble :
-FIRST (lucky ?) : try another usb cable
-HARD : format via cwm and proceed http://forum.xda-developers.com/showthread.php?t=2069723
I'm pretty sure @dimi89 just went threw this; he is an early p880' user and will help for steps or different way (?)
Once done, you need to flash cwm and a custom rom to check that AboutPhone/baseband is showing exact kdz :"LGP880AT-00-V20c-EUR-XXX-OCT-07-2014" and not the version firmware 02.1233, ie a different kdz origin.
(Under resulting LG JB, the AboutPhone/os firmware indication is always the rom in use, not the original kdz, so it always looks good even if not...like old 2013 V20C or remix... )
Click to expand...
Click to collapse
Thanks for your response!
"-FIRST (lucky ?) : try another usb cable"
Tried another one, but the errors stay the same. I also know that the cable I use worked for data transfer before.
"-HARD : format via cwm and proceed http://forum.xda-developers.com/showthread.php?t=2069723"
I tried that, but the LG software update tool keeps saying "phone not found"... Tried an 2.0 usb port at the back of my PC and also here tried a different cable - the error persists.
Phil_Smith said:
Thanks for your response!
"-FIRST (lucky ?) : try another usb cable"
Tried another one, but the errors stay the same. I also know that the cable I use worked for data transfer before.
"-HARD : format via cwm and proceed http://forum.xda-developers.com/showthread.php?t=2069723"
I tried that, but the LG software update tool keeps saying "phone not found"... Tried an 2.0 usb port at the back of my PC and also here tried a different cable - the error persists.
Click to expand...
Click to collapse
Okay, I tried it on a PC that natively runs Windows 7 and of course again the Windows version caused the mess... On that 7 machine everything went smoothly (although the "Cannot connect to server" error persisted, I was able to ignore it, as the program proceeded in the background).
Really to all of you having issues with upgrading LG software and running Windows 8 or higher:
Do not waste hours and simply try on a Windows 7 machine!
I remember having had troubles likes that before on win 8.1 , where the only solution in the end had been the same... it can drive you mad, so just please skip that!
Now I'm on cm11 nightly and "about phone" still shows L6260_MODEM_SIC_02.1233.00 under Baseband-Verison ...
Phil_Smith said:
Okay, I tried it on a PC that natively runs Windows 7 and of course again the Windows version caused the mess... On that 7 machine everything went smoothly (although the "Cannot connect to server" error persisted, I was able to ignore it, as the program proceeded in the background).
Really to all of you having issues with upgrading LG software and running Windows 8 or higher:
Do not waste hours and simply try on a Windows 7 machine!
I remember having had troubles likes that before on win 8.1 , where the only solution in the end had been the same... it can drive you mad, so just please skip that!
Now I'm on cm11 nightly and "about phone" still shows L6260_MODEM_SIC_02.1233.00 under Baseband-Verison ...
Click to expand...
Click to collapse
I'm now on @csk1jw 's new 7.1 ROM where my baseband version now shows the correct "LGP880AT-00-V20c-EUR-XXX-OCT-07-2014" which seems to be good, right?
GetRIL though still says "unknown RIL", but I'm not sure if that's just normal.
Related
Here we go ( Read all instruction and comment before start flashing ) :
1 ) Download these 3 apps: http://www.4shared.com/rar/Re4VCOAS/kdz- udpate.htm (the original link is deleted, re-uploaded by RuedasLocas)
To get KDZ file you can find it here : http://lg-phone-firmware.com/index.php?id_mod=15
2 ) Once downloads complete Extract the file (ex.: C:\KDZ\) and u will get folder like this :-
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3) Install B2CTools LG ( B2CAppSetup.exe ) this file is located on the folder that yr extract before .
4) Run LGMobile update (must be on your desktop) and install the usb drivers .
5 ) Turn off yr device and remove the battery .
6 ) Now just hold down vol - key ( hold hold hold dont release !!!! ) and plug the USB cable until you get screen like this :-
7 ) Wait for while due to yr computer will install some driver . Once the install is complete find "Device Manager" > Modems > disable the LGE Mobile USB Modem on yr computer ( me using win 7 -----> start ---> computer ---> right click / and you can find device manager )
8) Run as administrator KDZ_FW_UPD.exe ( file located at step no 2 )
9) - Run as administrator Windows Enabler.exe ( file located at step no 2 ) . After run the app, an icon will appear on your tray, single-click on the icon util the "ON" text appears over the icon like this :-
10 ) Go back to KDZ, locate press on the yellow folder and locate the .kdz file that you want to flash
11) Click on "Launch Software Update"
12 ) Please see below picture !! Very important !!!! Now standby to put yr battery back !!!!!!
When the log start to run, put the battery back on. ( thanks to RuedasLocas ) im copy from u
13 ) - WAIT until your phone reboots automatically and unplug the cable , ( ALL IS DONE ) please check yr firmware on yr phone ....
- Dont care about the errorlog, it's normal
If you got only bootloop after flash .kdz, just do a hard reset:
- press and hold [vol -] and [power] until you got the "android recovery figure" and wait until they reboot again.
INFO !
When you tried to update yr LG Optimus 4x HD , the error comes " Your Device Is Not Registered Yet "
That because you're using different version than the original country and you wont receive OTA update .
The only way to get it back is by using LG software or KDZ method and install yr country's firmware.
I hope this will help for those want to update firmware via KDS
And thanks to RuedasLocas because always help if we in trouble .. Thanks bro ..............
Before start flashing please do backup first ( yr photos , Videos , music on yr SD card )
For clean install wipe yr data / factory reset !!!
Did you really need to make another thread but with pics? Honestly, I think reading is enough.
Sent from my LG-P880 using Tapatalk 2
Thanks very helpful even if it is there in another thread
Sent from my LG-P880 using xda premium
babymatteo said:
Did you really need to make another thread but with pics? Honestly, I think reading is enough.
Sent from my LG-P880 using Tapatalk 2
Click to expand...
Click to collapse
yup i think so .. because on pinned tutorial there some confusion step . If think this thread rubbish just delete it !:good:
Someone will use this thread to upgrade the firmware .. Reading + picture = :good::good::good::good:
esag21 said:
Here we go ( Read all instruction and comment before start flashing ) :
1 ) Download these 3 apps: http://www.4shared.com/rar/Re4VCOAS/kdz- udpate.htm (the original link is deleted, re-uploaded by RuedasLocas)
To get KDZ file you can find it here : http://lg-phone-firmware.com/index.php?id_mod=15
2 ) Once downloads complete Extract the file (ex.: C:\KDZ\) and u will get folder like this :-
3) Install B2CTools LG ( B2CAppSetup.exe ) this file is located on the folder that yr extract before .
4) Run LGMobile update (must be on your desktop) and install the usb drivers .
5 ) Turn off yr device and remove the battery .
6 ) Now just hold down vol - key ( hold hold hold dont release !!!! ) and plug the USB cable until you get screen like this :-
7 ) Wait for while due to yr computer will install some driver . Once the install is complete find "Device Manager" > Modems > disable the LGE Mobile USB Modem on yr computer ( me using win 7 -----> start ---> computer ---> right click / and you can find device manager )
8) Run as administrator KDZ_FW_UPD.exe ( file located at step no 2 )
9) - Run as administrator Windows Enabler.exe ( file located at step no 2 ) . After run the app, an icon will appear on your tray, single-click on the icon util the "ON" text appears over the icon like this :-
10 ) Go back to KDZ, locate press on the yellow folder and locate the .kdz file that you want to flash
11) Click on "Launch Software Update"
12 ) Please see below picture !! Very important !!!! Now standby to put yr battery back !!!!!!
When the log start to run, put the battery back on. ( thanks to RuedasLocas ) im copy from u
13 ) - WAIT until your phone reboots automatically and unplug the cable , ( ALL IS DONE ) please check yr firmware on yr phone ....
- Dont care about the errorlog, it's normal
If you got only bootloop after flash .kdz, just do a hard reset:
- press and hold [vol -] and [power] until you got the "android recovery figure" and wait until they reboot again.
INFO !
When you tried to update yr LG Optimus 4x HD , the error comes " Your Device Is Not Registered Yet "
That because you're using different version than the original country and you wont receive OTA update .
The only way to get it back is by using LG software or KDZ method and install yr country's firmware.
I hope this will help for those want to update firmware via KDS
And thanks to RuedasLocas because always help if we in trouble .. Thanks bro ..............
Before start flashing please do backup first ( yr photos , Videos , music on yr SD card )
For clean install wipe yr data / factory reset !!!
Click to expand...
Click to collapse
Thanks ，I think If this or any other articles have helped you in any way, please tell one (or many) people about us. It's good job
:thumbup: Thanks
Sent from my LG-P880 using xda premium
Thank u sooo muchh!
All tht i needed..step by step thnks a lot. now seems easier
---------- Post added at 03:28 PM ---------- Previous post was at 03:18 PM ----------
one doubt...In type> does 3GQCT matters? if so..then what do i select for Indian GSM/3G sim?
23anand23 said:
All tht i needed..step by step thnks a lot. now seems easier
---------- Post added at 03:28 PM ---------- Previous post was at 03:18 PM ----------
one doubt...In type> does 3GQCT matters? if so..then what do i select for Indian GSM/3G sim?
Click to expand...
Click to collapse
ur welcome .. enjoy with new firmware .....:highfive: just follow the instruction then everything is done smoothly ...
Hansey said:
Thanks ，I think If this or any other articles have helped you in any way, please tell one (or many) people about us. It's good job
:thumbup: Thanks
Sent from my LG-P880 using xda premium
Click to expand...
Click to collapse
Seriouslly? You realy had to quote the whole first post?
Nice tutorial thank you. :thumbup:
Gesendet von meinem LG-P880 mit Tapatalk 2
babymatteo said:
Did you really need to make another thread but with pics? Honestly, I think reading is enough.
Sent from my LG-P880 using Tapatalk 2
Click to expand...
Click to collapse
Even with pictures will appear someone with some problem...
Normal, even cause there are other settings available and required to specific kind of flashes.
The work is very good specially the intention.
Thanks @esag21 :good:
RuedasLocas said:
Even with pictures will appear someone with some problem...
Click to expand...
Click to collapse
+1. Exactly this.
I think no need to remove battery
Still work even skip step 5
I updated my firmware , just by downloading the update software and following the instructions on the screen. Didn't disable modem and didn't remove battery. As far as I can see everything works fine. Battery is a bit crazy sometimes. One night I left it 100% before I went to sleep and found it at 100% in the morning and the other night I lost around 4% which is still ok.
I do get tiny lags in some games sometimes, not sure if I'm imagining it or not, but it didn't happen before, now I'm not sure if it's bcs I didn't remove the battery or disabled modem as you described.
Also is it possible for me to reflash from v10h to v10h but now disabling modem and removing battery?
elfen.lied said:
I updated my firmware , just by downloading the update software and following the instructions on the screen. Didn't disable modem and didn't remove battery. As far as I can see everything works fine. Battery is a bit crazy sometimes. One night I left it 100% before I went to sleep and found it at 100% in the morning and the other night I lost around 4% which is still ok.
I do get tiny lags in some games sometimes, not sure if I'm imagining it or not, but it didn't happen before, now I'm not sure if it's bcs I didn't remove the battery or disabled modem as you described.
Also is it possible for me to reflash from v10h to v10h but now disabling modem and removing battery?
Click to expand...
Click to collapse
Elfen Lied, ftw!
and yeah, You can do it
reas0n said:
Elfen Lied, ftw!
and yeah, You can do it
Click to expand...
Click to collapse
and will I get anything by doing that. Since I don't seem to be having any issues right now as far as I understand android
Also why go through all that procedure of removing the battery and disabling the modem when the simple version plug and follow instructions works as well? At least it did for me.
Some program behavior depends on your own computer setting, programs and drivers. Don't mean that the tutorial is wrong cause it's not. Your all welcome to post helpful hints but please, don't flood with minor issues. Thanks
Sent from my LG-P880 using xda app-developers app
RuedasLocas said:
Some program behavior depends on your own computer setting, programs and drivers. Don't mean that the tutorial is wrong cause it's not. Your all welcome to post helpful hints but please, don't flood with minor issues. Thanks
Sent from my LG-P880 using xda app-developers app
Click to expand...
Click to collapse
Well in order to be helpful here's what I did:
1. Installed LGMobile Support Tool (I'm sure you can google it )
2. Run the program and click on Install USB Driver.
3. After the driver finished downloading and installing, close the LGMobile Support Tool and plug in your phone via USB cable.
4. Now run LGMobile Support Tool again and it will start checking your device. At this time I also changed my Country by going to Options & Help ----> Country and Language.
5. After that I clicked on START UPDATING and followed the instructions.
I'd describe instructions in detail, but since my phone is already updated, the START UPDATING button is greyed out.
After the process has finished phone reboots into a new firmware which you can confirm in settings and the Tool itself confirms it.
Hope this helps!
elfen.lied said:
Well in order to be helpful here's what I did:
1. Installed LGMobile Support Tool (I'm sure you can google it )
2. Run the program and click on Install USB Driver.
3. After the driver finished downloading and installing, close the LGMobile Support Tool and plug in your phone via USB cable.
4. Now run LGMobile Support Tool again and it will start checking your device. At this time I also changed my Country by going to Options & Help ----> Country and Language.
5. After that I clicked on START UPDATING and followed the instructions.
I'd describe instructions in detail, but since my phone is already updated, the START UPDATING button is greyed out.
After the process has finished phone reboots into a new firmware which you can confirm in settings and the Tool itself confirms it.
Hope this helps!
Click to expand...
Click to collapse
Thank you for your help but, in order to avoid another messed thread like all the others, lets get stick to the topic please.
"Update firmware through flashing the kdz files"
great tutorial
Great tutorial. Thanks a lot. I didn't get any error message.
finally an updated tutorial :good:
All credits of this solution go to user dcseek who brought us the solution for this incredible annoying bug on our phones. It's not a bug actually. I think we should blame ourselfs, because it went all wrong when flashing a baseband. Personally I think it goes wrong when flashing a baseband fails and you have to try it again (yup, smartflash) or when flashing a korean baseband.
I decided to make a thread in the Q&A section, BUT BE CAREFUL!!! this is serious business, but concerning how many noobs are facing this bug (like me), it's worth to fix it.
Before you continue, all data will be wiped! Make sure to backup anything you need!!! Including Internal SD!!!
I am NOT responsible for any damage you possible create. I don't think you can brick your phone because our phone seems to be unbrickable, but I do not want to be blamed for any damage. I just made a guide on which I spent some of my free time to make it easier. I saw a lot of questions regarding hyperterminal. All I can say is: it's quiet easy!
Q: What's the problem?
A: Data connection won't be established after let's say beïng 20 minutes or more on wifi. Airplane on/off or rebooting is the only way to fix... There are also other problems related tot this fix. No guarantee, but connection losses etc. can be fixed with this!
Q: What causes this problem?
Two possible reasons, both are beïng fixed with this procedure:
A1) imei is totally lost or reset to something like 356200000000000 Check your imei by calling *#06#
A2) Some old calibration data in the radio will cause an unknown network state, which is actually edge (the fastest GSM connection). Old radio calibration data needs to be cleared.
Q: Are there other concequences?
A1: Yes, edge won't work, so everytime edge is requested, you will get a signal drop. I'm not sure but it seems like signal loss is caused by this
A2: 3g battery drain! Radio is sending a lot of data to the provider, I logged it and I saw many old useless data passing.
How do you do it?
First you will need a stock based rom. I recommend Stefan's unbrick rom, because you can flash it over every setup. You don't have to think about what you have right now, wether you've ICS, GB, CM, Stock, it doesn't matter. It's also a very easy one-click installation.
Download here It's a customized stock rom with a lot of nice upgrades and features, but the most important thing for this tutorial is to have a rom which everyone can flash with a few clicks and also contains the hidden menu from LG.
How to install?
Unpack rom
- Unpack Stefan's 7z file with 7zip or your favourite unzipper.
- 7zip is free, click
Prepare Phone
-Power down phone
-Remove battery
-Hold VOL_DWN+VOL_UP & plug in USB connection from computer (note, your phone will not visibly respond but it will boot to APX mode quickly)
-Open Device Manager in Windows and you should see "APX Device" listed with an error, or not if you have used NVFlash before
-Right click on the APX device
-Select 'Update driver software'
-Select 'Browse my computer...'
-Select 'Let me pick...'
-Select 'Have disk'
-Browse to directory you extracted the *driver* software to above (It's included in Stefan's zip)
-Select 'NVIDIA USB Boot-recovery driver for mobile devices'
-Accept any warnings, including the big red alert (you may need to disable UAC)
-Now in Device Manager under 'USB Controllers' you should have an 'NVIDIA USB Boot-recovery driver for mobile devices'
If not, uninstall the driver, reboot, rinse and repeat
Install the rom:
- Go to the folder where you unpacked Stefans rom
- Run Windows installer and follow instructions on screen, should be peace of cake for everyone!
- DONE
Now you've got a stock rom, it's time to flash your favorite baseband. Thanks to TonyP, there is a special topic about basebands. Please do not discuss here which one to choose.
TonyP's baseband tread
Flash it like normal, except for checking Erase CAL data. This time you have to enable the checkbox:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you get an error near the end, please see TonyP's topic how to solve! Or try 10 times like me, then it works too.
Congratulations! If your imei wasn't lost yet, it is now Now we have to restore it.
Step one - download Hyperterminal:
Download free trial, works perfectly on win7 x64 and more: click
Step two - connect phone in the right way
Boot the stock rom, you can cancel setup wizzards if you want. It's not important. Go to phone and call 1809#*990# when you have an old stock rom and call 3845#*990# when you have an ICS stock rom. Thats the hidden menu. Go to port settings and select CP USB (which is Com Port USB). Just click OK without clicking the checkbox to set it on boot. Connect USB cable and wait for your PC to install the drivers.
If all goes well, go to device manager (right click computer > properties > device manager somewere over there)
Note that in my case, it's com6. In your case it could be different. Write down which com port says LGE mobile USB serial port.
Step three - configure the program:
It's easy. Start as admin. Just cancel all the phone and location setup's until you get a blank terminal screen.
Click cancel in this window:
Then click yes to continue cancelling in the popup. Then the following window will appear. Click cancel too:
Now you should see a blank window. Click in it somewhere. A new window appears where you can choose the right com port. Choose the right one, which we got from the previous step. Note that it's probably just 'com x' and NOT LGE xxx xxx (that one sounds more logic but that's another port).
Click properties and select the right options like these:
Click ok twice and you if you did it right, you see this window with the state 'connected' in the lower left corner:
Type 'AT' (without the quotes) and hit enter. Wait for response. If response is 'OK' then you did a good job! Continue to the next step. If you don't see OK try another com port until you see OK.
Now I don't have any screenshots left. But now it's peace of cake.
Type: at%imei [hit enter]
Result is your current imei. You can check it.
Now, you have to write your own imei back with the following command (imei is on a sticker under the battery):
Originally Posted by Raum1807
You should add that the IMEI number must be entered without dashes. It seems to be a common mistake.
For example if your IMEI on the sticker is 123456-78-901234-5 then the command must be at%imei=123456789012345
Just type that, like 'at%imei=123456789012345' (without quotes) and hit enter. You should get a message that your imei is written with succes. Close hyperterminal and reboot your phone.
Check your imei by calling *#06#
It should be the whole number without stripes and dashes.
After this procedure, just flash your own favourite rom back. You can do this as many times as you want. Don't be affraid to damage anything, allthough this procedure is at your own risk.
Gd job x_justin mate it will definitely benefit lots of ppl. Awesome!!:thumbup:
Tnx mate! If there are any things unclear, just tell me.
well done
thanks this seems to have done the trick, I thought it was an ics/jb on p990 problem
Aaaaaaand your thread has been added to my Baseband thread. :good:
I'm sure this will help some people to follow the procedure.
I'd love to see a couple logcat lines added which are typical for this problem.
tonyp said:
Aaaaaaand your thread has been added to my Baseband thread. :good:
I'm sure this will help some people to follow the procedure.
I'd love to see a couple logcat lines added which are typical for this problem.
Click to expand...
Click to collapse
Thanks, I updated the installation progress. Now Stefan's unbrick rom is recommended and installation instructions are included.
If someone plans to run this tutorial, please tell me if something is wrong with one of the steps.
Double post, never mind
ive often wondered about this you mentioned.
i have it go 3g for a split second then revert to H all the time. sometimes just unlocking my fone and watching it do it 3-4 times. with nothing active.. =/
hope this fix's my terrible battery life and radio drain.
thanks for your hard work.
I did this and it didn't work for my phone...
Every time it looses 3g it doesn't switch to edge, and if I ask it to go to edge it doesn't finds it. ..
I must reset my phone to get edge connection which I rarely lose...
Will my problem be related to something else?
I do have a p990 but done in Korea sold in Europe
Sent from my LG-P990 using xda app-developers app
emilic said:
I did this and it didn't work for my phone...
Every time it looses 3g it doesn't switch to edge, and if I ask it to go to edge it doesn't finds it. ..
I must reset my phone to get edge connection which I rarely lose...
Will my problem be related to something else?
I do have a p990 but done in Korea sold in Europe
Sent from my LG-P990 using xda app-developers app
Click to expand...
Click to collapse
it does say in the instructions you won't be able to get an edge connection after the fix. As the signal around here is always 3g or hspa it worked like a treat.
Re: Fixing Data > WiFi transition and other radio problems
Ok it is working now!!!!
I almost never loose signal and can paas from 3g to edge!!!
Basically I inactivated the 3g for 1 day and le my phone run on edge... then I turned on the 3g And magic!!!
Now my phone changes to edge automatically when I am in the metro, etc.
Mwahhahaha by the way I am on v30b for baseband and original Rom.
I also love my battery life
Sent from my LG-P990 using xda app-developers app
if i flash stefans rom
does that mean i'm on the new bootloader then?
and if so, how can i convert back to the old and cm10.1
i now encountered a problem during the process
i'm in hyperterminal
connected with correct settings
but i can't type anything
update:
really checked 15 times and the port was com6, then suddenly it changed to com4 and everything worked.
solved
thank you for the tutorial
Solved
Re: Fixing Data > WiFi transition and other radio problems
My Problem was not fixed by this.
When i set airplanemode and back i get no gsm connection until i restart my phone
Sent from my Nexus 7 using Tapatalk HD
Thank you, this is a very useful guide !
derEremit said:
if i flash stefans rom
does that mean i'm on the new bootloader then?
and if so, how can i convert back to the old and cm10.1
Click to expand...
Click to collapse
yes if u flash the "ICS" Stefan's ROM then you have now the NewBL "ICS Bootloader"
if you want to return to the old "GB BL"
Use this.
http://forum.xda-developers.com/showthread.php?t=2020737
i cant write AT into hyperterminal - so i dont know what to do - i did every step carefully and everything worked fine until now... pls HELP
If you use "xFSTK-SoC-Driver-Setup" and "unbrick.bat" to "Unbrick your phone, and you got the "Service code corrupt" error..., This method is untested but i think it is the problem...You need This:
Original ICS FIRMWARE that come with your phone.
xFSTK-SoC-Driver-Setup Installed (read How Install "xFSTK-SoC-Driver-Setup")
Unbrick.bat and respective folders.
Motorola Handset USB Drivers (x86 or x64).
ADB/ FASTBOOT or SDK.
Steps to revive:
Extract Unbrick.zip in "C:\atomSOC"
Go to unbrick folder. "C:\atomSOC\unbrick"
Go to your firmware folder and copy this files (dnx; ifwi)
Replace this files in "C:\atomSOC\unbrick".
Press CAMERA button and Plug in the USB to your phone (MEDFIELD FLASH)
Run unbrick.bat in "C:\atomSOC"
How Install "xFSTK-SoC-Driver-Setup":
Run Setup
When Say "Intel Soc Is about to begin" Click OK
When Say "In Order to Complete (...) Will a device be attached (...)" Press Yes.
When Say "Step 1 (...)" Plug In your USB Cable to the pc. and click ok
When Say "Step 2 (...)" Press CAMERA button and Plug in the USB to your phone (MEDFIELD FLASH)
¿How know if my phone go to the medfield flash method?
release the camera button, your phone will stay in a black screen with the green led.
And your pc says "New hardware recognized"
Name of hardware: MEDFIELD
Before the driver install:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Downloads:
Unbrick.bat + xFSTK-SoC-Driver-Setup Download
If it works.. please, let me know
Nope.
I just tried it, and it starts the download says a few numbers then carries on downloading.
Then the phone reboots and goes to the service required code corrupt screen
1994deano said:
I just tried it, and it starts the download says a few numbers then carries on downloading.
Then the phone reboots and goes to the service required code corrupt screen
Click to expand...
Click to collapse
Try again, your phone is not going to medfield flash mode correctly
I did not get the part - Go to your firmware folder and copy this files (dnx; ifwi)
How to go to firmware folder?,
I do not understand how to copy
i just re tried it and its got rid of the service required screen but now the screen is just black with the green led on
Me too samething, any sugestion?
gmpdri said:
Me too samething, any sugestion?
Click to expand...
Click to collapse
csn you boot to bootloader?? (power+vol.down)?
Nope
pangyaaaaaa said:
csn you boot to bootloader?? (power+vol.down)?
Click to expand...
Click to collapse
no that is why we are trying to use the medfield flash, as the bootloader is screwed up
1994deano said:
no that is why we are trying to use the medfield flash, as the bootloader is screwed up
Click to expand...
Click to collapse
I found some tools for intel lenovo pad, im trying to found how work, im think i can use it on razr i...
Boss442 said:
I found some tools for intel lenovo pad, im trying to found how work, im think i can use it on razr i...
Click to expand...
Click to collapse
ooh nice, let us know how you get on with it
S***, REALLY GOOD NEWS.....
RDS recognizes your phone on Medfield Mode...
Someone try to flash a firmware
Flashing Firmware dont work... ¿Maybe a custom XML Work?
HELP
For that ADB / Fastboot or SDK.?
Copying pro firmware?
saiko.sensei said:
For that ADB / Fastboot or SDK.?
Copying pro firmware?
Click to expand...
Click to collapse
if i found a way for bypass the "service required" error.. maybe you need fastboot... I am working with a lenovo pad (Intel SoC) maybe can use his flash tool to work (need fastboot). But dont recognize my phone, ¿Maybe need a custom driver? i am working in that
Yes, RSD lite recognises bricked phones, but it tries to enter fastboot mode to flash anything, so we're stuck...
Good luck!
Bricked while flashing JB Radio to ICS
hy,
i did the stupid error of flashing a jb radio fw to a ics phone, now also with this tool i only get the message "service required / code corrupt"
anny idea?
btw.: i found a gui tool that does the same thing, there you can not only upload the firmware but also an operating system (you need a fw dnx and ifwi file and a os dnx and image file) anny idea where we could get the os files? i suppose flashing both (fw and dns) would unbrick the phone in all bricking cases.
i know it has already been said, but turn off your phone and keep the camera button pressed while connecting it (if you get the service required error). if the screen stays black just run the tool.
in my case flashing an ics fw dnx leads to the device corrupt message, and flashing a jb fw dnx leads to the black screen.
Boss, you are a good man for trying to help other people. Getting something like this working in the community would be brilliant, as I've tried to communicate to others. The most help I got was from outside the RAZR i forum, most here just don't give a sh1t in helping others. I have created 2 help threads to guide people - information to help prevent further cases.
I have concluded the same - that 'unbrick.bat' fixes some problems and creates a far bigger one - the service required, code corrupt problem. I wasn't sure if I could say that directly but I've a lot of messages in my inbox about this and almost everyone arrived at that after using that unbrick. How that is still available is incredible, since it's the biggest brick-creator on here that I know.
mercurio. said:
hy,
i did the stupid error of flashing a jb radio fw to a ics phone, now also with this tool i only get the message "service required / code corrupt"
anny idea?
btw.: i found a gui tool that does the same thing, there you can not only upload the firmware but also an operating system (you need a fw dnx and ifwi file and a os dnx and image file) anny idea where we could get the os files? i suppose flashing both (fw and dns) would unbrick the phone in all bricking cases.
i know it has already been said, but turn off your phone and keep the camera button pressed while connecting it (if you get the service required error). if the screen stays black just run the tool.
in my case flashing an ics fw dnx leads to the device corrupt message, and flashing a jb fw dnx leads to the black screen.
Click to expand...
Click to collapse
You can found Ifwi and dnx in your firmware folder... download a rds firmware and you found the two files. Upload and send me the gui-tool please!
So.. You cannot downgrading ifwi and dnx, but if you use ifwi and dnx (JB) with a ICS system, you got the black screen... so the black screen brick and "service required"brick are the same brick
SharpnShiny said:
Boss, you are a good man for trying to help other people. Getting something like this working in the community would be brilliant, as I've tried to communicate to others. The most help I got was from outside the RAZR i forum, most here just don't give a sh1t in helping others. I have created 2 help threads to guide people - information to help prevent further cases.
I have concluded the same - that 'unbrick.bat' fixes some problems and creates a far bigger one - the service required, code corrupt problem. I wasn't sure if I could say that directly but I've a lot of messages in my inbox about this and almost everyone arrived at that after using that unbrick. How that is still available is incredible, since it's the biggest brick-creator on here that I know.
Is your phone bricked in this condition right now? If it is, feel free to PM me.
Click to expand...
Click to collapse
My phone isn't bricked, i know people that unbrick.bat work right, but some people brick your phone, so i know this is a "Most devices problem" (Firmware problem, work for people that IFWI and dnx are extracted from the same firmware that are using)
Unbrick.bat provides a tool can flash some files (IFWI & DNX) to the phone (These files are responsible for the brick) and i only im working with the same tool that can solve the problem, unbrick.bat (or xFSTK-Downloader) is a good tool, but the use brick the phone, example: if i solve my downgrading brick , and i upload my files (Unbrick.bat with ifwi and dnx) this work only for people with use my firmware (example: Orange ICS), for other people that uses other firmware (Claro Argentina) the phone bricks and show "Service required blah blah blah" im trying to go back to the original "ifwi and dnx" files, some people on other forums says that the phone dont show anymore the "service required" error... but the phone only shows a green led (same thing that downgrading brick).
xFSTK-Downloader is used to update the Orange sandiego (First Intel Atom android, dont use fastboot) and Ienovo pad (Use xFSTK-Downloader-GUI, and a "Flashtool").
xFSTK-Downloader is like a Odin for intel phones. sorry for my english but if you know spanish pm me and can explain more
I read 80 pages in modaco for intel san diego and 40 for Ienovo pad, and they uses xFSTK-Downloader to update the phones.
Boss442 said:
You can found Ifwi and dnx in your firmware folder... download a rds firmware and you found the two files. Upload and send me the gui-tool please!
So.. You cannot downgrading ifwi and dnx, but if you use ifwi and dnx (JB) with a ICS system, you got the black screen... so the black screen brick and "service required"brick are the same brick
My phone isn't bricked, i know people that unbrick.bat work right, but some people brick your phone, so i know this is a "Most devices problem" (Firmware problem, work for people that IFWI and dnx are extracted from the same firmware that are using)
Unbrick.bat provides a tool can flash some files (IFWI & DNX) to the phone (These files are responsible for the brick) and i only im working with the same tool that can solve the problem, unbrick.bat (or xFSTK-Downloader) is a good tool, but the use brick the phone, example: if i solve my downgrading brick , and i upload my files (Unbrick.bat with ifwi and dnx) this work only for people with use my firmware (example: Orange ICS), for other people that uses other firmware (Claro Argentina) the phone bricks and show "Service required blah blah blah" im trying to go back to the original "ifwi and dnx" files, some people on other forums says that the phone dont show anymore the "service required" error... but the phone only shows a green led (same thing that downgrading brick).
xFSTK-Downloader is used to update the Orange sandiego (First Intel Atom android, dont use fastboot) and Ienovo pad (Use xFSTK-Downloader-GUI, and a "Flashtool").
xFSTK-Downloader is like a Odin for intel phones. sorry for my english but if you know spanish pm me and can explain more
I read 80 pages in modaco for intel san diego and 40 for Ienovo pad, and they uses xFSTK-Downloader to update the phones.
Click to expand...
Click to collapse
I found out that the tool I ment is the xFSTK-Downloader ( rghost.net/44421368 ) that was alreaddy linked here at xda by U1138 in: http://forum.xda-developers.com/showthread.php?t=2184877
And yes, i suppose the black screen only and the service required brick are the same. they probably are due to a not working combination of firmware (ifwi & dnx) and flashed OS (i suppose the fastboot, no idea how where to get the dnx file needed for flashing it). you can try different ifwi and dnx files and get different results (so far i think there are only two types, the ones for JB fw and the others for ICS).
If you flash your rom with RSD going from JB to ICS you also flash the ifwi & dnx files, but not the bootloader. Therefore you end up with a non working combination of firmware (ifwi) and OS (fastboot) => nothing starts at all.
This problem was easy to fix for me flashing the appropriate JB firmware.
Then I did the mistake of flashing the JB radio before flashing a JB rom. This lead to a situation where neither the JB (leads to service required warning) nor the ICS (black screen, green led on) firmware works anymore and I have no idea how i could change the situation.
Anyone has some ideas how to flash the fastboot with the xFSTK-Downloader?
mercurio. said:
Anyone has some ideas how to flash the fastboot with the xFSTK-Downloader?
Click to expand...
Click to collapse
+ 1
Everything else I was try with U 1138`s help - without result
St.Noigel said:
+ 1
Everything else I was try with U 1138`s help - without result
Click to expand...
Click to collapse
I read more than 120 pages in forums, and... NOTHING!
But i'm triyng to port a "flash tool" from lenovo pad... :silly:
Hello, i was given a blu R1 HD prime phone that was bricked by one of my relatives, according to him, he tried to do a format all + download on this phone, which as far as im aware, is a death flag, so i have here this bricked phone, i installed mrmazak's prime 6.1 no nv.zip file on this phone, but it still gives me the TOOL DL IMAGE FAIL, error i've heard a lot about, i also saw him saying "THIS IS NOT THE PACKAGE YOU NEED" in which case i can do nothing but ask, whats the correct package to get this bad boy up and running again? thanks beforehand.
PS: The phone is 8gb/1gb ram ver. was on ver 6.1, amazon before the brick, no OTA's.
Shinnazuka0411 said:
Hello, i was given a blu R1 HD prime phone that was bricked by one of my relatives, according to him, he tried to do a format all + download on this phone, which as far as im aware, is a death flag, so i have here this bricked phone, i installed mrmazak's prime 6.1 no nv.zip file on this phone, but it still gives me the TOOL DL IMAGE FAIL, error i've heard a lot about, i also saw him saying "THIS IS NOT THE PACKAGE YOU NEED" in which case i can do nothing but ask, whats the correct package to get this bad boy up and running again? thanks beforehand.
PS: The phone is 8gb/1gb ram ver. was on ver 6.1, amazon before the brick, no OTA's.
Click to expand...
Click to collapse
For a device that was format all. Will need more partitions than are in that package you tried. Also I have tried to work with someone else who had the 8gb size device, we could not get past that error.
I do recall that the last last person got a new board for his phone and pulled the images from it to share. There is a link in the main thread somewhere. But , well even when he tried to restore his own backup from good device to the one with do error, it did not work.
NVM
I remembered it wrong. He tried to pull it, but could not do it.
Look through this thread. Maybe you can try to follow the advice I gave him, and it may work for you.
https://forum.xda-developers.com/r1...-blu-r1-hd-t3440261/post76482224#post76482224
Well, from this mess in english, i can kind of attempt to understand that he tried to install v17 backup, and it didnt work due to the PMT CHANGED FOR THIS ROM, then he somewhere got a .bin backup for miracle?, and then silence, i dont know what else you tried suggesting to him since his english was so bad, i cant follow the steps, on another note, got that .bin backup? maybe ill try flashing it with miracle tool and praying that it'll work. Also, which V17 should i use, NVRAM or NONV
Shinnazuka0411 said:
Well, from this mess in english, i can kind of attempt to understand that he tried to install v17 backup, and it didnt work due to the PMT CHANGED FOR THIS ROM, then he somewhere got a .bin backup for miracle?, and then silence, i dont know what else you tried suggesting to him since his english was so bad, i cant follow the steps, on another note, got that .bin backup? maybe ill try flashing it with miracle tool and praying that it'll work. Also, which V17 should i use, NVRAM or NONV
Click to expand...
Click to collapse
There is now a "repair rom" listed in an mtk support group I try to follow. I have not checked it out yet, but maybe it will help. Let me open this on PC to search for the link
this one was labled v6.4 firmware http://www.mediafire.com/file/6kys9896445l5sm/SP_Flash_Tool_BLU_R0010UU_V6.4_Firmware.zip/file
this is labled as a repair firmware http://www.mediafire.com/file/il54pxuvpkargtr/BLU_R1_HD_R0030UU_REPAIR_MT6735.rar/file
I would have you look at those , first i suppose.
if it does not work I do have backups made from miricle-box, but they are not uploaded anywhere right now.
Real appreciated, will keep you updated, if anything works ill post it here.
Alright, i tried the 6.4 rom, it didnt work, i had it already, i also tried to install the "repair firmware" but in the v5.1628.00.000 version of my SPFT it shows me "SP FLASH TOOL ERROR: (8417) THE LOAD SCATTER FILE IS INVALID", then i try on another version (v5.1744 & v5.1804), then tells me STATUS_SCATTER_FILE_INVALID (0xC00300001), i tried the fix copypasting the hashtags and general settings on top for both cases but that didnt work, i noticed the scatter file looks really weird, not like most of the ones posted here or elsewhere, its just a bunch of rows and not organized in the slightest, maybe i need to try using the scatter for my 8gb/1gb ram? since R0030UU is the 16gb/2gb ram's model code
---------------------------------------------------------------------------------------------------------------------------------------------------------------EDIT: Tried mixed and matching the every file from the MT6735 repair firmware with the ones it didnt have from the prime 6.1 rom whilist using said 6.1 scatter, still on TOOL DL IMAGE FAIL
Shinnazuka0411 said:
Alright, i tried the 6.4 rom, it didnt work, i had it already, i also tried to install the "repair firmware" but in the v5.1628.00.000 version of my SPFT it shows me "SP FLASH TOOL ERROR: (8417) THE LOAD SCATTER FILE IS INVALID", then i try on another version (v5.1744 & v5.1804), then tells me STATUS_SCATTER_FILE_INVALID (0xC00300001), i tried the fix copypasting the hashtags and general settings on top for both cases but that didnt work, i noticed the scatter file looks really weird, not like most of the ones posted here or elsewhere, its just a bunch of rows and not organized in the slightest, maybe i need to try using the scatter for my 8gb/1gb ram? since R0030UU is the 16gb/2gb ram's model code
---------------------------------------------------------------------------------------------------------------------------------------------------------------EDIT: Tried mixed and matching the every file from the MT6735 repair firmware with the ones it didnt have from the prime 6.1 rom whilist using said 6.1 scatter, still on TOOL DL IMAGE FAIL
Click to expand...
Click to collapse
all I can do is share the backup from miricle-box that I have.
https://www.androidfilehost.com/?fid=5862345805528042536
Just trying to catch up, so bricked phone that wont format correct? Do you have twrp on it?
mrmazak said:
all I can do is share the backup from miricle-box that I have.
androidfilehost/?fid=5862345805528042536
Click to expand...
Click to collapse
Hi, this work on BLU R0030UU 2GB/16GB or R0010UU??
TavoStyle said:
Hi, this work on BLU R0030UU 2GB/16GB or R0010UU??
Click to expand...
Click to collapse
This is from 16gb so the R0030uu
mrmazak said:
This is from 16gb so the R0030uu
Click to expand...
Click to collapse
Hi!, I am from Venezuela, I apologize for my English, I am using the Google translator ...
I tried to put the software but the following error appears
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
TavoStyle said:
Hi!, I am from Venezuela, I apologize for my English, I am using the Google translator ...
I tried to put the software but the following error appears
Click to expand...
Click to collapse
Hello,
two issues.
first, the backup has scatter file formatted for use in miracle box, not sp flash tool.
next, The preloader on any updated phone has been changed and does not work to flash anymore.
So, what is / was version on your phone , so I can know if it should be able to work or not?
\
mrmazak said:
Hello,
two issues.
first, the backup has scatter file formatted for use in miracle box, not sp flash tool.
next, The preloader on any updated phone has been changed and does not work to flash anymore.
So, what is / was version on your phone , so I can know if it should be able to work or not?
\
Click to expand...
Click to collapse
First: If I use Miracle Box Crack 2.27A, can it work? (Would I have to disconnect and connect the battery to start the phone again?)
Next: I unchecked the Preloader because once I leave a brick as a phone to leave marked that option
Version: (Screen OLD, Now is in BLU Screen) (Ohhh I never UPDATE the software, I never use ROOT, I never use debloat...)
TavoStyle said:
First: If I use Miracle Box Crack 2.27A, can it work? (Would I have to disconnect and connect the battery to start the phone again?)
Next: I unchecked the Preloader because once I leave a brick as a phone to leave marked that option
Version: (Screen OLD, Now is in BLU Screen) (Ohhh I never UPDATE the software, I never use ROOT, I never use debloat...)
Click to expand...
Click to collapse
Most important part (custom build number) is missing from screen shot.
mrmazak said:
Most important part (custom build number) is missing from screen shot.
Click to expand...
Click to collapse
I just discovered something very crazy, I do not understand anything
In the recovery logs...
https://youtu.be/-sMubZoduig
TavoStyle said:
I just discovered something very crazy, I do not understand anything
In the recovery logs...
https://youtu.be/-sMubZoduig
Click to expand...
Click to collapse
so your build number is 6.6
you may be able to unlock.
But is phone still alive?
mrmazak said:
so your build number is 6.6
you may be able to unlock.
But is phone still alive?
Click to expand...
Click to collapse
My phone is stuck in the BLU logo
TavoStyle said:
My phone is stuck in the BLU logo
Click to expand...
Click to collapse
if it is still locked bootloader, and stock recovery fails to wipe data and / or cache. I do not have idea how to fix.\
Bricked BLU R1 HD
mrmazak said:
if it is still locked bootloader, and stock recovery fails to wipe data and / or cache. I do not have idea how to fix.\
Click to expand...
Click to collapse
Hi Mr Mazak
I had purchased non prime version of BLU R1 HD. I updated to the latest version via OTA. I had my phone rooted with super su and now wanted to try Magisk. After the reboot I had reinstalled the twrp recovery and did a format of all data on my phone. I am trying to install twrp but when I power on my device it is stuck on the boot loading screen. I have tried hold power button and volume down simultaneously and it reboots but gets stuck on the logo.
I tried using the sp flash tool to restore my phone to stock but it did not work. Get error S_BROM_DOWNLOAD_FAIL. 7d
My bootloader is unlocked.
Tried using adb commands but when I connect to the phone and run adb commands it says no authorisation.
If I can install twrp on the device then I will be able to install the rom from rootjunky, not sure if you require more info.
Awaiting your ananlys
Kind Regards
ismailf007 said:
Hi Mr Mazak
I had purchased non prime version of BLU R1 HD. I updated to the latest version via OTA.
Click to expand...
Click to collapse
The latest ota blocks the use of sp flash tool. And the kernel exploit used previouls. But now there is new exploit. But you cannot boot so that is mutt point now
ismailf007 said:
I had my phone rooted with super su and now wanted to try Magisk. After the reboot I had reinstalled the twrp recovery and did a format of all data on my phone.
Click to expand...
Click to collapse
Did you only format the data partition or whole device.?
ismailf007 said:
I am trying to install twrp but when I power on my device it is stuck on the boot loading screen.
Click to expand...
Click to collapse
This confuses me. You just said you had twrp already. Now you have trouble to I stall it.
ismailf007 said:
I have tried hold power button and volume down simultaneously and it reboots but gets stuck on the logo.
Click to expand...
Click to collapse
Did you use / try volume up?
ismailf007 said:
I tried using the sp flash tool to restore my phone to stock but it did not work. Get error S_BROM_DOWNLOAD_FAIL. 7d
My bootloader is unlocked.
Click to expand...
Click to collapse
From what you say.
1. You had working phone with SU root.
2. You have twrp installed
3. You wiped / formated with twrp
4. You now only boot to a logo screen. No recovery, or bootloader?
Here is a collection of files for the BTV-W09, BTV-DL09 and BTV-L0j. They are somewhat organized and contain firmware, board software, roll back packages with instructions and a poor quality un-edited video of how to flash with IDT successfully. The image for test point location is good for w09 and dl09. I don't know if they are the same on the l0j from Japan or not. Should you truly need a file for the BTV variants of the M3, leave a reply to let me know what it is and I'll see what I can do.
DISCLAMER:
There are other Huawei firmware and board software within this thread. Any use of them is at your own risk, although if you're here you've already screwed something up, whether you believe yourself to be at fault or not.
Flashing board software is a last resort and should not be done unless all other methods have been exhausted. Only flash board software when there are no other alternatives.
https://www.mediafire.com/folder/43cwcl8hih2u2/MediaPad_M3_(BTV-W09,L0J,DL09)
BTV-W09 Stock Firmware
https://drive.google.com/file/d/16UhYMILV83C6MwdVqmwYKDf0JA6LOAV5/view?usp=sharing
https://drive.google.com/file/d/1g7-rNMGzIRCpKelj2GNdPvhORAmC3z8R/view?usp=sharing
https://drive.google.com/file/d/1oAwRv3F08SnAhpkBXw4m_elVhmtg3ie2/view?usp=sharing
https://drive.google.com/file/d/17Ck8zaKlqfP4FmJSRUuM8fNUETY-2-sU/view?usp=sharing
Hi! There's any chance something like this for CPN-L09 version? I would be very happy for this, but I think not just me.
Beren
Barahir's son Beren said:
Hi! There's any chance something like this for CPN-L09 version? I would be very happy for this, but I think not just me.
Beren
Click to expand...
Click to collapse
What are you needing ? Board Software I do have for CPN-L09 and can get others.
Barahir's son Beren said:
Hi! There's any chance something like this for CPN-L09 version? I would be very happy for this, but I think not just me.
Beren
Click to expand...
Click to collapse
Here's board software for CPN-L09
CPN-L09C500B028_Board Software_general_7.0.0_r1_EMUI5.1_05022FWM
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
tek3195 said:
Here's board software for CPN-L09
CPN-L09C500B028_Board Software_general_7.0.0_r1_EMUI5.1_05022FWM
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
Click to expand...
Click to collapse
Please, do you have the same files for BAH-AL00/BAH-L09 ?
I have been struggling for a few months to repair my tablet but I didn't find anywhere the right file ( prog_emmc_firehose_8937_ddr.mbn ) for my tablet .
Or I can use the files from CPN-L09 ?
Thank you very very much in advanced !
tek3195, I already tried with CPN files but I have always error with :" Sahara protocol error" , "Uploading Image using Sahara protocol failed" ... I'm using QFIL as administrator with Antivirus disabled & Airplane mode enabled on my laptop and nothing changed about Sahara protocol error, and even I used "emmcdl.exe -p COM5 -f prog_emmc_firehose_8937_ddr.mbn -x rawprogram0.xml" - also without success !
Anyway, I think the battery is close to 0 and there are very poor chances to repair it.
tek3195 said:
What are you needing ? Board Software I do have for CPN-L09 and can get others.
Click to expand...
Click to collapse
Hi!
Thanks for your quick reply. I need a working solution to take back to factory firmware. I tried it many times, but I haven't succeeded, I always got a recovery screen or bootloop. Is it possible with your files and method?
Beren
Barahir's son Beren said:
Hi!
Thanks for your quick reply. I need a working solution to take back to factory firmware. I tried it many times, but I haven't succeeded, I always got a recovery screen or bootloop. Is it possible with your files and method?
Beren
Click to expand...
Click to collapse
Sure, you have all what you need there, just use Qualcomm Flash Image Loader ( QFIL Tool )
surdu_petru said:
Please, do you have the same files for BAH-AL00/BAH-L09 ?
I have been struggling for a few months to repair my tablet but I didn't find anywhere the right file ( prog_emmc_firehose_8937_ddr.mbn ) for my tablet .
Or I can use the files from CPN-L09 ?
Thank you very very much in advanced !
Click to expand...
Click to collapse
I wouldn't try cpn on bah, even with same firehose loader it shouldnt work.If it did flash it may make a hard to recover brick.
I can get BAH2-AL00 or BAH-L09. Which one would you like ? I can't find one for BAH-AL00
surdu_petru said:
tek3195, I already tried with CPN files but I have always error with :" Sahara protocol error" , "Uploading Image using Sahara protocol failed" ... I'm using QFIL as administrator with Antivirus disabled & Airplane mode enabled on my laptop and nothing changed about Sahara protocol error, and even I used "emmcdl.exe -p COM5 -f prog_emmc_firehose_8937_ddr.mbn -x rawprogram0.xml" - also without success !
Anyway, I think the battery is close to 0 and there are very poor chances to repair it.
Click to expand...
Click to collapse
I haven't flashed qualcomm in a while but the error may be from wrong software if using CPN on a BAH. Anyway, I can get BAH-L09 and Iwill have to dig around and find another tool for flashing Huawei/Qualcomm. I hve it but can't remember the name of it right now. It's a lot simpler than QFIL.
tek3195 said:
I wouldn't try cpn on bah, even with same firehose loader it shouldnt work.If it did flash it may make a hard to recover brick.
I can get BAH2-AL00 or BAH-L09. Which one would you like ? I can't find one for BAH-AL00
Click to expand...
Click to collapse
On the back side of my tablet it has a label and it says BTV-AL00, but on the settings the menu it says BTV-L09 !
Anyway, I guess I can't recover my device as battery seems to be almost empty and when the QFIL start to make some operations, the device seems to turn off frequently ( at least the drivers keep disconnecting and reconnecting itself )
Thank you very much in advanced !
EDIT:
I managed to brick my device by flashed a wrong TZ.img via TWRP !
I know it was stupid of me, but now I have nothing to do with it!
surdu_petru said:
On the back side of my tablet it has a label and it says BTV-AL00, but on the settings the menu it says BTV-L09 !
Anyway, I guess I can't recover my device as battery seems to be almost empty and when the QFIL start to make some operations, the device seems to turn off frequently ( at least the drivers keep disconnecting and reconnecting itself )
Thank you very much in advanced !
EDIT:
I managed to brick my device by flashed a wrong TZ.img via TWRP !
I know it was stupid of me, but now I have nothing to do with it!
Click to expand...
Click to collapse
Is it BAH-L09 or BTV-L09 ? I have bah-l09 uploading now, it has board software and a rollback update.app in it along with other release documentation. I can't remember if the Huawei tool I'm looking for needs battery or not. Seems like it flashes without it.
I really don't know if it's Al00 or L09 .... as I said on the back it has a label with BAH-AL00 and something written in Chinese but the getprop it say : BAH-L09 !
Also it's working with kernel compiled from Huawei BAH-L09 source code ... but this it's not so relevant as also CPN devices are working with BAH-L09 source code !
EDIT :
Yes, we talk about Huawei MediaPad M3 Lite 10 / BAH-L09 !
@surdu_petru here is folder with board software and tools for BAH-L09. Still haven't found the other tool I was looking for.
Ok, I'll try right now, Thanks !
tek3195
Thank you very much for your help! Unfortunately, for unknown reasons my device can't stay connected on edl mode - so there is no way to flash something via edl mode !
Tthe device seems to communicate successfully only immediately after it has been connected via usb - in edl mode ... unfortunately, a few seconds later the device can no longer be detected !
Tested with : "emmcdl -p COM15 -info'' - and working only one time ( as soon as the device has been connected ) - and if I tried the same command for the second time, there is no device detected like into the picture !
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
surdu_petru said:
tek3195
Thank you very much for your help! Unfortunately, for unknown reasons my device can't stay connected on edl mode - so there is no way to flash something via edl mode !
Tthe device seems to communicate successfully only immediately after it has been connected via usb - in edl mode ... unfortunately, a few seconds later the device can no longer be detected !
Tested with : "emmcdl -p COM15 -info'' - and working only one time ( as soon as the device has been connected ) - and if I tried the same command for the second time, there is no device detected like into the picture !
Click to expand...
Click to collapse
It looks like it is still connected and recognized in 9008 mode even after invalid handle status. Different software to flash it with would be my thought. I am not very well versed in Windows and have a Sigma Key Huawei Edition that takes the hard work out of most issues like this one. However, there are free software that will fix it I believe, it's just a matter of finding the right one and then a version of it thst supports msm8937. QPST or QFIL that I see in background I have never had any luck with other than one Lenovo tablet. I will look for the one tool that I have had good luck with in the past. I can't remember the name but I will know it when I see it.
tek3195 said:
It looks like it is still connected and recognized in 9008 mode even after invalid handle status. Different software to flash it with would be my thought. I am not very well versed in Windows and have a Sigma Key Huawei Edition that takes the hard work out of most issues like this one. However, there are free software that will fix it I believe, it's just a matter of finding the right one and then a version of it thst supports msm8937. QPST or QFIL that I see in background I have never had any luck with other than one Lenovo tablet. I will look for the one tool that I have had good luck with in the past. I can't remember the name but I will know it when I see it.
Click to expand...
Click to collapse
It will be awesome if you can get me the right tool for flash, as I already tried a lot of tools and non working, thanks !
@surdu_petru here is the one that I have had best luck with. There should be a "how to use" file with it.
https://www.mediafire.com/file/w8ql6u0ue2usb7e/Huiye_Download_Tool_v2.2.zip/file
tek3195 said:
@surdu_petru here is the one that I have had best luck with. There should be a "how to use" file with it.
https://www.mediafire.com/file/w8ql6u0ue2usb7e/Huiye_Download_Tool_v2.2.zip/file
Click to expand...
Click to collapse
Thank you very much for your help.
I guess that I have the same connectivity issues also with this Tool :