Help Please my nexus 6 stuck on fastboot - Nexus 6 Q&A, Help & Troubleshooting

help pls
i have nexus 6 and it just stuck on fastboot icant unlock bootloader and cant boot recovery i cant flash it even with rsd its not show as motorola device
just adb reinstalled the windows and just put driver for motorola and its read android again
tested the driver with moto e and its work
so how i can recover my device if i cant flash it :crying::crying::crying::crying:
​

Slow down...
Give some (as much as possible really) details as to what you've done to end up where you are.
Preferably in a normal non-centered text because what you've done there is hard on the eyes (read: annoying) and almost put me off answering...

Prince_Eugen said:
help pls
i have nexus 6 and it just stuck on fastboot icant unlock bootloader and cant boot recovery i cant flash it even with rsd its not show as motorola device
just adb reinstalled the windows and just put driver for motorola and its read android again
tested the driver with moto e and its work
so how i can recover my device if i cant flash it :crying::crying::crying::crying:
​
Click to expand...
Click to collapse
Well as you get the info ready, I will give you some advise. RSD is useless on the nexus 6. It is moto software for moto software and the nexus is is moto in name only.
Also the drivers for the moto E and nexus 6 might not be the same thing. Just because it is a moto doesnt mean anything.

zelendel said:
Well as you get the info ready, I will give you some advise. RSD is useless on the nexus 6. It is moto software for moto software and the nexus is is moto in name only.
Also the drivers for the moto E and nexus 6 might not be the same thing. Just because it is a moto doesnt mean anything.
Click to expand...
Click to collapse
ok thaks but what should i do now ?

Provide details. LOTS of them.
Basically, we need to know what you're attempting to do here.

Strephon Alkhalikoi said:
Provide details. LOTS of them.
Basically, we need to know what you're attempting to do here.
Click to expand...
Click to collapse
wake up found it stuck in bootloader i didnt do anything
i cant flash rom or do any thing

If you have no ROM, cannot enter recovery, and did nothing to bring this state of affairs about, your phone most likely has a dead EMMC storage chip. You can verify this by trying to flash a stock ROM using the fastboot command, but be aware that attempting to use that Lenovorola program you mentioned could have done significant damage to the device, as that program is not intended for this device.
Should we be able to confirm a dead EMMC chip, there's not that many options available. If you are still under manufacturer warranty you can send the device to Lenovorola for repair at no cost. Otherwise, you'd have to pay for the repair. You could instead purchase a replacement, or purchase a device with a broken screen and swap motherboards (and SIM trays).

Related

I failed on root. My brand new Moto X has been hardbricked.

[Solved] Yesterday I tried to root my phone but after do all the steps that were on the sites, I couldn't turn it on anymore. Everytime I try it makes the bootloader but when it ends, the moto x turns off again. I don't know what happened someone told me that it names hardbrick so, can anyone tell me how to fix it? Or if it's possible.
If you need some information to help me, just ask. [Solved]
If you can get to the bootloader is not bricked.
Look up how to use fastboot to flash the system and boot img.
Go to soltrans' thread and you should be fine
Sent from my victara
fastercon said:
Go to soltrans' thread and you should be fine
Sent from my victara
Click to expand...
Click to collapse
http://forum.xda-developers.com/moto-x-2014/general/guide-update-xt1095-pure-edition-to-t2937074
Start with step "0".

How to unbrick hard bricked MOTO G 2nd Gen (xt1068)

My phone is totally bricked not even opening in bootloader. It's only recognized by pc as "qhsusb_bulk". so I signed my phone with "Riff BOX JTAG drivers Driver Signature Enforcement Overrider". after this my phone is recognized as "Qualcomm HS-USB QLoader 9008" under Ports (COM & LPT). Then I extract Motorola qboot utility and then run blank-flash.bat file after that this is showing (flashing singleimageFAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet).
maybe that singleimage.bin file is problematic.
So I need correct blank-flash file for my phone.
Help me guys. thanks in advance.
deleted. Reason : OP edited.
sagar846 said:
Have you tried giving it CPR? (jk)
Just reflash stock firmware.
Link : Click Here
Click to expand...
Click to collapse
edit..
zman01 said:
Very useful post.. Did you read the OP or you're just guessing here?
Click to expand...
Click to collapse
Op edited post. Before there was only hard brick problem given (when I posted).
Well, there is a good chance that you can't do anything about it. But, give as some info about what you did to it, what was the last version of Android or Rom on it, and so on.
Addy K said:
My phone is totally bricked not even opening in bootloader. It's only recognized by pc as "qhsusb_bulk". so I signed my phone with "Riff BOX JTAG drivers Driver Signature Enforcement Overrider". after this my phone is recognized as "Qualcomm HS-USB QLoader 9008" under Ports (COM & LPT). Then I extract Motorola qboot utility and then run blank-flash.bat file after that this is showing (flashing singleimageFAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet).
maybe that singleimage.bin file is problematic.
So I need correct blank-flash file for my phone.
Help me guys. thanks in advance.
Click to expand...
Click to collapse
I get the same place in my moto g 2014 xt1069. Do i have any chance to create a blackflash from original lollipop ROM?
EDIT: blankflash*
marcoslucianops said:
I get the same place in my moto g 2014 xt1069. Do i have any chance to create a blackflash from original lollipop ROM?
Click to expand...
Click to collapse
Nope, you don't have any
Addy K said:
...
Click to expand...
Click to collapse
Can you give me the files you used?
Well this guide might work for you guys. Its for the moto g1 but everything used in the guide is kind of the same for all moto devices except the firmware. Don't forget to download the correct firmware for your phone :
Click Here
sagar846 said:
Well this guide might work for you guys. Its for the moto g1 but everything used in the guide is kind of the same for all moto devices except the firmware. Don't forget to download the correct firmware for your phone :
Click Here
Click to expand...
Click to collapse
This won't work, ^^ the "blank flash" in the tutorial you've sent us, is only for the Moto G 1st gen, i've already tried it ^^ this is not compatible :/
This is why we need the blank flash for the Moto G 2014, then this tuto will work ^^
Miiick3y said:
This won't work, ^^ the "blank flash" in the tutorial you've sent us, is only for the Moto G 1st gen, i've already tried it ^^ this is not compatible :/
This is why we need the blank flash for the Moto G 2014, then this tuto will work ^^
Click to expand...
Click to collapse
Check the firmware download link again (file factory). There are 5+ pages. Find the right firmware for your phone (Itll be labelled TITAN CFL blah blah)
Flash it.
Direct link : Click Here
sagar846 said:
Check the firmware download link again (file factory). There are 5+ pages. Find the right firmware for your phone (Itll be labelled TITAN CFL blah blah)
Flash it.
Direct link : Click Here
Click to expand...
Click to collapse
Thanks for help, but i can't flash anything, my phone is only recognized on my pc as a qualcomm communication port ^^
Addy K said:
My phone is totally bricked not even opening in bootloader. It's only recognized by pc as "qhsusb_bulk". so I signed my phone with "Riff BOX JTAG drivers Driver Signature Enforcement Overrider". after this my phone is recognized as "Qualcomm HS-USB QLoader 9008" under Ports (COM & LPT). Then I extract Motorola qboot utility and then run blank-flash.bat file after that this is showing (flashing singleimageFAILED (blank-flash:sdl-transfer-image:sdl-hello:error sending packet).
maybe that singleimage.bin file is problematic.
So I need correct blank-flash file for my phone.
Help me guys. thanks in advance.
Click to expand...
Click to collapse
@Andy K
Found the reason why it didn't work. That is because that method is used to rescue Qualcomm Snapdragon devices. Our device is Qualcomm based so yeah. Here's a kinda detailed explanation
Owners of Qualcomm based LG’s, HTC’s, Samsung’s, Sony’s and Motorola’s, im afraid this tool is not suitable for you, because those liers mostly have chosen not to use default options of this platform, they dont (cant) want us to rescue our phones so easly, what would have happened to their service centers all around the world then ? They need to change “The Motherboard” in spite of the ability to fix this problem so easly to earn more and more and more money.
Site Link : Click Here
I was on stock Marshmallow 6.0 rom. Then I flashed stock Lollipop 5.0.2 rom in my phone and then I was updating my phone to new stagefright patch but after switch off my phone didn't turn on again.
My last android version was Marshmallow 6.0. I downgraded my phone to Lollipop 5.0.2 and tried to update latest stagefright patch from system update. But after switched off my phone never turn on again. Whenever I connect my phone to the charger it's shows nothing but white led light for 10 seconds. And my phone recognised by my PC as "qshusb_bulk".
Need Moto G 2nd Gen "blankflash image" to flash new bootloader.
As the bootloader of my phone has been collapsed so I need to flash a new bootloader to my phone to relive. But I don't have the right file. And I don't think there is any blankflash image of my phone (XT1068) is available on the net. So I just need to know that is there any way to extract these file from Stock ROM?
Addy K said:
As the bootloader of my phone has been collapsed so I need to flash a new bootloader to my phone to relive. But I don't have the right file. And I don't think there is any blankflash image of my phone (XT1068) is available on the net. So I just need to know that is there any way to extract these file from Stock ROM?
Click to expand...
Click to collapse
No there is no way. I think they already got 5.0 singleimage, but the problem is with programmer.mbn. Without motorola signature it won't flash the bootloader..
still no hope...
Do you have 5.0 or 6.0 singleimage file?
am stuck in the same position. the company has to come up with the new bootloader file. or upload the xt1068 bootloader. one method is throught riff jtag . but very few repair guys have that box. in mumbai they charge 1000-1500rs to repair such phones

Bootloader bricked.

Due to att for 6.0 moto G does not turn over any way
resulting in a hard brick or better one bricked bootloader
because I can not access it.
Anyway, I install the Qualcomm drivers but when I use the blankflash.bat simply will not
I've tried other methods and also all the blank says only "<waiting for device>"
and I'm currently without mobile phone and hope the fastest possible response, thanks.
First of all. Why you changed your Thea/XT107X's bootloader, if it's fine for running all 5.X/6.X ROMs? A bad OTA is a possibility. Also there is no blankflash for 6.0 AFAIK. Give me more info and I might find a solution.

Moto G 2nd Gen ( XT1068) hard bricked: neither turning on, nor opened by blankflash

One morning i restarted my phone( Moto G 2nd gen.) with Android Marshmallow because it went slow, but after that it restarted in fastboot mode when i pressed the power on button. Normal startup or recovery were also not working.
I checked this forum, then unlocked the bootloader and downgraded to Android 4.4.4 . My phone operated well, then at night it started asking for lollipop update again and again, i allowed for OTA update (that was my biggest mistake), and after downloading the data and during update, my phone went off and didn't start again.
Although the indicator light glows solid for sometime when connected to wall charger or to PC via USB cable.
I have tried blankflash, ADB and fastboot utility, Volume down + Power combination, pressing power button for over 120 seconds, but all in vain.....
Please suggest me a way to solve this problems, i have important data in my phone and i want to save those too.
Welcome to the hardbrick club ^^
They all did the same mistake like you did. When you go throught the motoG Threads you will see all did the same.
The only solution is a clean flash what is not given from motorola for moto g2. The only existing is for moto g what did not work for our phones
Feel blessed, you don't have to use moto g anymore.
Anniepoo said:
Welcome to the hardbrick club ^^
They all did the same mistake like you did. When you go throught the motoG Threads you will see all did the same.
The only solution is a clean flash what is not given from motorola for moto g2. The only existing is for moto g what did not work for our phones
Click to expand...
Click to collapse
I tried with blankflash which supports android 4.4 but not 5.0, so it must be a requiring MBM-CI 5.0 ? is it available or any expected month of arrival?
aninishu said:
I tried with blankflash which supports android 4.4 but not 5.0, so it must be a requiring MBM-CI 5.0 ? is it available or any expected month of arrival?
Click to expand...
Click to collapse
. I wish I could say it was, but unfortunately Motorola won't release this file. There have been some serious attempts to solve this problem but none have succeeded.. As far as I know the only way to fix this problem is by getting a new motherboard..
Hellow
friend, do not know if motorola and released this file, or if there are already solution ?, I appreciate your answer
Diego799 said:
friend, do not know if motorola and released this file, or if there are already solution ?, I appreciate your answer
Click to expand...
Click to collapse
no blankflash.zip for our model available
if you are from india then you can try out this solution for xt1068 by an guy mobile unbrick something contact him but remember it will be paid not free
Code:
https://www.youtube.com/watch?v=WynBaVyW0oU
if you from another region then need to wait for blank flash zip
There are some methods to extract the partition layouts...one can be using dd cloning & extracting img files...another can be through B2bSupportLg Tool, also calleld BoardDiag. It does have MSM8226 chipset option, but that device is W7 G2MDS. Take a working Moto G 2014 from someone, ask them to use this tool to extract the partition schemes, then you'll get .mbn files, especially prog_emmc_filehorse_msm8226.mbn . Use that to dump into the bricked device using either QFIL Tool or use this blankflash tool, replace it's singleimage files with the one you got, then execute blank-flash.bat.
Also I had some emmc prog firehorse files, all 4 related to 8x26...You can try those & confirm me if they work or not

Need help

Hey guys n girls,
I'm going to root my phone. First off the why? I recently discovered PlayStation remote play and use it on my computer. I was excited to use it on my phone but then found out only Sony phones work I guess... So I read somewhere don't remember, that if I root my phone, I can add Sony files to rooted phone to allow it to use PlayStation remote.
1st phone is moto x 2nd
2nd phone zte maven 2
First phone I use for an actually phone 2nd one is brand new never used.
So I heard I need to use adb and something else I believe. Can someone help me? Once again main reason PlayStation remote play
mike543210 said:
Hey guys n girls,
I'm going to root my phone. First off the why? I recently discovered PlayStation remote play and use it on my computer. I was excited to use it on my phone but then found out only Sony phones work I guess... So I read somewhere don't remember, that if I root my phone, I can add Sony files to rooted phone to allow it to use PlayStation remote.
1st phone is moto x 2nd
2nd phone zte maven 2
First phone I use for an actually phone 2nd one is brand new never used.
So I heard I need to use adb and something else I believe. Can someone help me? Once again main reason PlayStation remote play
Click to expand...
Click to collapse
First you must unlock bootloader from official motorola site.
Google unlock moto x 2014 and do it.
Second you must download adb and fastboot to your pc.
Third with adb flash twrp.
And last flash supersu with tuttorial from xda .
Keep walking.
Thanks. Any chance you can attach links for downloads for PC and also files. If u can add tutorials I can follow those too. I have rooted couple times before but if I do the moto that's my actual phone and I don't want to mess it up. Will it mess with my plan or screw me over in any way? I've only done phones I don't use.
Thanks again for any help
So Ive been reading and need a little help.
1. I have moto x2014 (is it pure edition?)supposedly. (It's at&t white front wooden back 8gb. Believe 5.1.1) I need to know so I can do the first step.
2.downloads to adb and fastboot for PC? I was hoping someone had a link so I know I don't download anything bad.
*Edit* I used this
https://forum.xda-developers.com/showthread.php?p=48915118
3. How to flash? And need the zip packs/files for twrp and SuperSU? (Which I put on root of SD card?)
*Edit*
Also by doing this will my phone operate the same?(no extra step to put kernal/os on?) I just want to know how to root and add Sony software to use the app. Thanks again for anyone's knowledge
*Edit*
I'm having a tough time navigating the forum, thank for the help people
mike543210 said:
So Ive been reading and need a little help.
1. I have moto x2014 (is it pure edition?)supposedly. (It's at&t white front wooden back 8gb. Believe 5.1.1) I need to know so I can do the first step.
2.downloads to adb and fastboot for PC? I was hoping someone had a link so I know I don't download anything bad.
*Edit* I used this
https://forum.xda-developers.com/showthread.php?p=48915118
3. How to flash? And need the zip packs/files for twrp and SuperSU? (Which I put on root of SD card?)
*Edit*
Also by doing this will my phone operate the same?(no extra step to put kernal/os on?) I just want to know how to root and add Sony software to use the app. Thanks again for anyone's knowledge
*Edit*
I'm having a tough time navigating the forum, thank for the help people
Click to expand...
Click to collapse
Here is my help....
Twrp
https://dl.twrp.me/victara/twrp-3.1.1-0-victara.img.html
Moto drivers
https://mobilesupport.lenovo.com/us/en/solution/MS88481
Unloack bootloader
https://motorola-global-portal.custhelp.com/app/standalone/bootloader/unlock-your-device-a
Minimal fastboot an adb
https://androidfilehost.com/?fid=745425885120698566
Here toutorial for the root.
https://forum.xda-developers.com/moto-x-2014/development/root-root-moto-x-2014-android-t3249105
Thank you I will read and try. And as far as if I root the zte maven 2 I would just get the drivers for zte and switch the product name in command lines correct?
First off thanks for your help and anybody else who may contribute.
ive been trying to listen and follow lol. anything with (...) is stuff
i added
First you must unlock bootloader from official motorola site.
Google unlock moto x 2014 and do it.
(the link you added brought my to a page i click next and tryed to sign up
it said i had an account so i signed in with the email on my phone an then it
brought me to a page that wasnt available. So do you have another link or is
there something im missing. im having trouble unlocking it)
Second you must download adb and fastboot to your pc.
(i downloaded
*minimal_adb_fastboot_v1.4.2_setup application
*motoroladevicemanager_2.5.4 application)
Third with adb flash twrp.
(few things.
*adb is just command prompt right?
*flash? i know means install sorta of. do you have command line?
*the link had three things to click on
1.this was on white screen
58337e4962e12d37f740a417601db4e3 twrp-3.1.1-0-victara.img
2. twrp-3.1.1-0-victara disc /image file
3. twrp-3.1.1-0-victara.img.asc /asc file)
And last flash supersu with tuttorial from xda .
(once again, flash? im assuming i just need command line like,
adb install supersu.apk.
*also files i downloaded were
1. update-supersu-v2.76-20160630161323 /compressed zip
2. root-boot-6.0-xt1097-mpes24.49-18-7 /compressed zip)
***So is there any files im missing to root?
How do i unlock my bootloader or whatever it is? (link didnt work for me)
What is flash?(i think install)
it says my device does not qualify to unlock bootloader. so yea I don't want to give up but that killed my hopes. I can get into fasboot flash mode and have boot mode selection menu and it says device is still locked. I got the link to work and used fastboot oem get_unlock_data used their program to have same layout for unlock code and it says your device does not qualify for bootloader unlocking. if anyone can help thanks
mike543210 said:
it says my device does not qualify to unlock bootloader. so yea I don't want to give up but that killed my hopes. I can get into fasboot flash mode and have boot mode selection menu and it says device is still locked. I got the link to work and used fastboot oem get_unlock_data used their program to have same layout for unlock code and it says your device does not qualify for bootloader unlocking. if anyone can help thanks
Click to expand...
Click to collapse
Some variants of the Moto X 2014 cannot be unlocked. Put the phone in Bootloader Mode and:
fastboot getvar all
Copy and save all the info into a Notepad file, then go to the Moto/Lenovo Forums here:
https://forums.lenovo.com/t5/MOTORO...ock-Problems/m-p/3222809/highlight/true#M2654
mike543210 said:
it says my device does not qualify to unlock bootloader. so yea I don't want to give up but that killed my hopes. I can get into fasboot flash mode and have boot mode selection menu and it says device is still locked. I got the link to work and used fastboot oem get_unlock_data used their program to have same layout for unlock code and it says your device does not qualify for bootloader unlocking. if anyone can help thanks
Click to expand...
Click to collapse
What model do you have my friend?
Fot the tutorial ...
First unlock bootloader and install twrp.
All other you can flash them from the twrp recovery and i mean supersu and many more.
From adb can flash stock rom clean.
hey gus I did that command and made a save file in notepad. so just post it?
and pap I believe xt1097
according to ur link gus my phone is not unlockable becaue my cid was 0x001. so yea I guess im giving up thanks guys for your time. im really bummed because I modded and rooted things in the pass and this by far has been the hardest. I figured I could do it manually or a custom firmware would help. if I install twrp somehow as a recovery is there a way to root of that? I just don't get y I cant unlock bootloader. I understand that I cant, but don't get how there isn't a way around it. once again thanks people. this is a bummer...........................
is there any way to get unique_key for the command line?
fastboot oem unlock UNIQUE_KEY
im so annoyed right now that i cant unlock this phone. its ridiculous that i cant unlock it, like seriously please help from anyone. i dont know y i cand get the unique key to unlock my phone. can i call motorola to ask for it? or at&t? i just dont get y i cant unlock it with any method. i know there is someone out there who can help, please spare me some time and help me i beg of u.
u think this will work?
https://forum.xda-developers.com/moto-x-2014/general/root-bootloader-unlock-att-xt1097-5-1-t3309889
or is there a way to make my bootloader unsigned?
if i unlock my phone from at&t would that help?

Categories

Resources