Related
i want to flash new firmware but i have little problem...now my tab is show exclamation point between a phone and a computer.
but Galaxy tab can not remove battery for reset this error...
Help me please....
water30 said:
i want to flash new firmware but i have little problem...now my tab is show exclamation point between a phone and a computer.
but Galaxy tab can not remove battery for reset this error...
Help me please....
Click to expand...
Click to collapse
what did you do to get to this screen? Is this after or before you upgraded firmware?
GANJDROID said:
what did you do to get to this screen? Is this after or before you upgraded firmware?
Click to expand...
Click to collapse
after upgrade firmware odin show reset but the my tab not reset then i just manual reset (i can take this method for my galaxys ) after that.....
Edit:
Had the exact same thing happen to me, but its just a bad flash.
Download the JM6 zip (in the development forum) and flash it via Odin. after the device has rebooted, if the previous apps havent been deleted, go into recovery and perform a factory reset and reboot again
i have the same problem, phone - exclamation point - computer ... but i can't get into recovery mode to do a wipe .
is i press VOLUME UP or DOWN + POWER i always end up with the same exclamation point screen ... any help?
primeroz said:
i have the same problem, phone - exclamation point - computer ... but i can't get into recovery mode to do a wipe .
is i press VOLUME UP or DOWN + POWER i always end up with the same exclamation point screen ... any help?
Click to expand...
Click to collapse
Read my above post. Go into download mode (volume down + home + power) you'll still have the same image but the phone WILL be in download mode. Then flash your previous firmware and you're sorted.
Sent from my GT-P1000
You probably got that by messing with the kernel. Fund the zImage from the firmware, extract it with a .tar extractor then use something like heimdall to flash the kernel and it should work.
Sent from my GT-P1000 using Tapatalk
Hi. I'm looking for solution for my problem but nothing has helped me. I cannot restart mu GTab or put it in download mode. I always land into Android system recovery <3e>.
My problem: I cannot restart my GTab anymore. It started when I wanted to do a backup with ROM Manager. Unfortunately EURO TAB isn't supported yet. Then I want to find out whether nandroid backup is possible. From ROM manager I booted into recovery. But there isn't nandroid backup. And now I cannot boot GTab anymore. Every time I restart it brings me back to Android system recovery <3e>. I would be grateful for every solution.
Help please
slaia said:
Hi. I'm looking for solution for my problem but nothing has helped me. I cannot restart mu GTab or put it in download mode. I always land into Android system recovery <3e>.
My problem: I cannot restart my GTab anymore. It started when I wanted to do a backup with ROM Manager. Unfortunately EURO TAB isn't supported yet. Then I want to find out whether nandroid backup is possible. From ROM manager I booted into recovery. But there isn't nandroid backup. And now I cannot boot GTab anymore. Every time I restart it brings me back to Android system recovery <3e>. I would be grateful for every solution.
Click to expand...
Click to collapse
Having the same problem too... anyone can help?
If you see Phone-!-Pc on the Tab screen it is the download mode.
You can reflash it using Odin, however, you will need to do full Rom flash. I had similar problem and solved it by replashing.
I followed the latest guide published in this forum and Roto-JME rom with reformatting of internal sd.
Phone ! PC error FML!!!
GANJDROID said:
Edit:
Had the exact same thing happen to me, but its just a bad flash.
Download the JM6 zip (in the development forum) and flash it via Odin. after the device has rebooted, if the previous apps havent been deleted, go into recovery and perform a factory reset and reboot again
Click to expand...
Click to collapse
Where can i download the JM6 zip??
Hey guys,
I tried to manually update my tab to Gingerbread today via Odin, but it kept hanging on select partition (I discovered I used the wrong PIT for the firmware I was going to flash, but as I didn't select the firmware yet that shouldn't be a problem). At last I decided to quit Odin (which might have been stupid...) and try it again. Then it kept haning even earlier, so I tried to restart the device in download mode. However, whatever I try it keeps giving the Phone ! PC sign. If I try to just boot, if I try to go into recovery mode or if I try to go into download mode. I saw a lot of possible ways to solve the problem, but my PC doesn't recognize the tab anymore. If I connect it, it does give the "usb device connected" sound, but there is a popup which sais "USB Device not recognized. One of the USB Devices attached to this computer has malfunctioned and Windows does not recognize it. For assistance in solving this problem, click this message". I already tried to reinstall the driver but it doesn't work. Also Odin and Heimdall don't detect any device.
Does anyone know a solution for this problem? Maybe taking the battery out? (for which I have to buy a new triangle screwdriver, so I need to know if it could possibly work first. It takes some weeks to order such a thing I think...)
EDIT: I played around a bit with the drivers again, and suddenly both Heimdall and Odin recognized it. However Odin stopped recognizing it again. Then I pressed "read PIT" in Heimdall, which worked. After that the device started booting up to the Samsung logo animation and then powered off again. Now it doesn't do anything anymore, not even showing the Phone ! PC screen. I'll charge it overnight (maybe it's gone empty during the process), so I hope that helps.....
In some strange way, the phone works again..... So never mind my post above.
Hi.
Basically , I Know NOTHING about all this 'flashing' roms and what not. I got this phone from a friend , and was aware that it had custom firmware or something on it. Due to the phone being severly slow , and constantly displaying errors along the lines of "the process com.android has stopped working" when I was trying to call or text somebody , I thought i'd have a play about with some settings in recovery mode thinking this was the way to restore back to custom out of the shop firmware (stupid i know). All I remember doing was clicking through a few menu's in the green text recovery mode screens and clicking "disable lagfix". I then got some form of error at the bottom , and the phone froze. I took out the battery , tried to re-boot it and it's getting no further than the very first screen with the "Galaxy S Samsung" etc etc.
I know this probably sounds stupid to some of you phone wizards on here , but i'd appreciate any help you could give in the simplest terms for somebody who has no clue about this whatsoever. If I was able to fix this , how would I also go about completely making the phone like it was brand new? No custom firmwares or Roms or anything along those lines?
Thanks very much in advance!
Ben.
well, if it kud b that the problem is caused coz u disabled lagfix. you could try re-enabling it and see whether you can get the phone to boot. to do that:
> shut-down the phone completely,
> hold down the VOLUME UP + HOME + POWER buttons simultaneously till the phone powers up and then let go,
> hopefully this will get you beyond the "galaxy S" screen and into recovery mode,
> from recovery mode re-enable the lagfix that you disabled earlier, then re-start the phone and see if it boots properly,
> if it does, shut-down the phone again, come back to recovery mode (as above) and perform a hard re-set (the options should be something like wipe data/factory reset in recovery mode) and restart phone - the general slowness and the errors u were getting were most probably from the apps that were installed in the phone. so, if u get rid of em all n re-install only the ones u r going to need, then this wus solve the issue,
Hope this helps,
Cheers,
HI thanks for your reply.
Im able to get into download and recovery mode. I though enabling the lagfix again would work , however , there is no option to enable it. Just to disable it again as though I never did it in the first place. Ive also tried wiping all cache's and factory restoring the phone , but it's still not going past the Samsung Galaxy S screen.
Any ideas?
how long are you letting it boot up for before switching it back off ? i have a few apps no more than 35. it takes the phone 10-15 mins to boot after disabling lagfix..
if your phone had lots more apps and music pics ... whatever. it could take even longer to convert all files back to rfs.. dont suppose you know what ROM is / was on the phone ?? do you / did you hear a robot voice when the phone boots ??
I've left it for hours. Still no luck getting past that screen. What can I do?
I have no idea what Rom it was , and there was no robot voice.
http://forum.xda-developers.com/showthread.php?t=818556
Via ODin go back to base rom .
jje
Oh wow , lengthy process!
Will try it all and report back to here to let you know how it goes.
Thanks!
Having a problem when I connect the phone to PC in download mode. Odin says "added" when the phone is on the Galaxy S screen , however if i then switch to download mode it says "removed" and wont detect the phone. Same if I have the phone in download mode before connecting.
Bumping for advice.
Benjiee said:
Having a problem when I connect the phone to PC in download mode. Odin says "added" when the phone is on the Galaxy S screen , however if i then switch to download mode it says "removed" and wont detect the phone. Same if I have the phone in download mode before connecting.
Click to expand...
Click to collapse
have you done a full factory reset in recovery mode ?? its strange whats happening to you. as if the phone can get into download mode then theoretically Odin should see the phone...
if you can get into recovery mode use every option to wipe the phone.. e.g full factory reset, wipe cache, wipe dalivk cache, then try again and post back
EDIT: also you could try format sd card (internal) this way there wont be a single thing left on the phone that could cause issues...
Odin wont recognise the phone when it's in download mode , only when it's on the boot screen.
I've factory reset it , wiped caches and formated the internal SD card. Still no luck getting past the Galaxy S Screen.
Open Odin select files .
Go to download mode on phone you should now have a big yellow icon
Connect usb cable
First block on Odin lights up press start Odin runs goes to blue phone reboots .
Is that your sequence of events ??
No.
The phone isn't recognized by Odin when it's in download mode , so i'm not even able to start the flash.
I open Odin ,
Select the Files ,
Put phone to Download mode and connect USB ,
Odin dosn't detect and block dosn't turn yellow.
However ,
It IS detected and turns yellow if the phone ISN'T in download mode. Soon as I switch to download mode , Odin says "Removed" and the yellow icon dissapears.
Can you get to download mode without connecting to Odin
heimdall might be an option
http://forum.xda-developers.com/showthread.php?t=755265&highlight=heimdall
jje
Unable to start the flash on Heimdall also , as it wont find phone.
I am lost wont find phone is usually a USB problem/USB drivers .
jje
The computer makes the usual Beep noise when plugging in a USB device , so it's obviously being detected. It just wont show up in ODIN when in download mode.
My next step would be to remove Kies and any Samsung Drivers .
Then reinstall Kies so you are 100% sure drivers are ok .
jje
All fixed now.
Used a USB port at the back of the computer , and it then worked fine with ODIN for some reason. Re-flashed original firmware and phone is now running much smoother than previously.
Thanks for all your help.
My phone is screwed up. I can't go into recovery mode. But I can go into Downloading Mode though. So I decided to flash a stock ROM but I can't cause my computer doesn't recognize my USB. Used to be able to. Restarted computer, re-installed drivers. used different computers but still nothing happened. USB NOT RECOGNIZED
how to get my phone back up
does the phone still work ?
No, it doesn't boot. Stuck in Galaxy S first screen before the boot animation.
Same thing happened to me not so long ago. Once it was in download mode I opened odin and it wouldn't recognise it so I then went straight into download mode again using 3 button combo and it writhed as far as I recall.
Hope this helps
Galaxy S - no point in writing rom or kernel constantly changing!
SOLVED: when having trouble with your computer not making a good connection to the phone, try your USB HUB on the mother board. it totally fixed my problem!
So here it is. I received a cappy from a buddy at work.
Basically, she is running cognition (FROYO BASED) rom, not sure of the kernal, and Cwm.
i can get the phone to reboot into RED CWM recovery, and even into DOWNload mode.
The phone was shut off during a factory reset. the battery died.
(IDK the girl was a dumbass and did it from settings on the phone not in CWM )
The phone will boot, ONLY after a factory reset from CWM but the setup google accs f/c's and the only thing i can get it to do is volume up/down pull the notification bar down and power off recovey dl mode...ect ect.
Task manager say's there are no APPS installed on the phone running? yet when i go LVL 2 RAM clear, the phone says 13 apps closed..
I think the Stock APK's have been deleted, since i cannot get into menu at all.
Since she factory reset the phone, and wiped the SD CARD, ALL CWM recoveries she created are GONE.
I have Cleared the cache, and wiped dalvik code, fixed permissions.....
I'm very familiar with the VIBRANTS, not the cappy's so this is a challenge to me.
my Vibrant has connected with all the usb drivers from samsung, but the cappy cannot. I've even downloaded the drivers for just the CAPPY, uninstalled all others, and Still not recognized, yet my vibrant does?
i've installed i think every driver on here for captivates, kies downloads, even went to the samsung website and Downloaded from there.
STILL NOT CONNECTING.
Even DL'd the AIO cappy toolbox (very nice to have for my VIBRANT)
Still no avail.
THE PHONE CANNOT MOUNT THE EX SD CARD. So that idea's out.
all my drivers are correct for the 32 bit vista OS. even tried on my GF's 64 Windows 7.
Still no avail.
I've installed the drivers with the phone in DOWNLOAD mode even, still not connecting.
Rebooted the computer after removing and also reinstalling drivers.
Changed between 3 diff cords, all work for my VIBRANT,
still no avail.
Any idea's would be greatly appreciated.
Thanks.
PelvicThunder said:
So here it is. I received a cappy from a buddy at work.
Basically, she is running cognition rom, not sure of the kernal, and Cwm.
i can get the phone to reboot into RED CWM recovery, and even into DOWNload mode.
The phone was shut off during a factory reset. the battery died.
(IDK the girl was a dumbass and did it from settings on the phone not in CWM )
The phone will boot, ONLY after a factory reset from CWM but the setup google accs f/c's and the only thing i can get it to do is volume up/down pull the notification bar down and power off recovey dl mode...ect ect.
Task manager say's there are no APPS installed on the phone running? yet when i go LVL 2 RAM clear, the phone says 13 apps closed..
I think the Stock APK's have been deleted, since i cannot get into menu at all.
Since she factory reset the phone, and wiped the SD CARD, ALL CWM recoveries she created are GONE.
I have Cleared the cache, and wiped dalvik code, fixed permissions.....
I'm very familiar with the VIBRANTS, not the cappy's so this is a challenge to me.
my Vibrant has connected with all the usb drivers from samsung, but the cappy cannot. I've even downloaded the drivers for just the CAPPY, uninstalled all others, and Still not recognized, yet my vibrant does?
i've installed i think every driver on here for captivates, kies downloads, even went to the samsung website and Downloaded from there.
STILL NOT CONNECTING.
Even DL'd the AIO cappy toolbox (very nice to have for my VIBRANT)
Still no avail.
all my drivers are correct for the 32 bit vista OS. even tried on my GF's 64 Windows 7.
Still no avail.
I've installed the drivers with the phone in DOWNLOAD mode even, still not connecting.
Rebooted the computer after removing and also reinstalling drivers.
Changed between 3 diff cords, all work for my VIBRANT,
still no avail.
Any idea's would be greatly appreciated.
Thanks.
Click to expand...
Click to collapse
First, see if you can find out which version of Cognition she was running (Gingerbread- or Froyo-based).
Once you have that information, I believe you should be able to download the appropriate ROM on you computer and copy it to the microSD card (adapter or whatever method you need to do to get it there). Since you can get into CWM recovery, you could try flashing the ROM from there. Assuming it's a full wipe rom (and you're not concerned about keeping apps installed on the phone), it should reset things to a more workable state. (If you are worried about apps remaining... I don't know what to say at this point, since you can't get to Tibu.)
If that doesn't work, you could try the one-click back to stock (realizing that you're having connectivity issues, I'll get to that in a second).
When you connect the phone in download mode to ODIN, does the yellow COM:# show up?
If you have tried ODIN on your Vista computer, try running ODIN as Administrator.
I've had some luck in the past getting the phone to be recognized (assuming Froyo) by doing this:
1. With nothing connected to computer, start ODIN (one-click to stock would be good).
2. Pull battery on phone.
3. Reinsert battery, but do not power on.
4. Hold Vol+/Vol-/, and insert USB cable.
5. Wait for it to kick into download mode, release buttons, and wait again.
6. See if ODIN recognizes it.
jmtheiss said:
First, see if you can find out which version of Cognition she was running (Gingerbread- or Froyo-based).
Once you have that information, I believe you should be able to download the appropriate ROM on you computer and copy it to the microSD card (adapter or whatever method you need to do to get it there). Since you can get into CWM recovery, you could try flashing the ROM from there. Assuming it's a full wipe rom (and you're not concerned about keeping apps installed on the phone), it should reset things to a more workable state. (If you are worried about apps remaining... I don't know what to say at this point, since you can't get to Tibu.)
If that doesn't work, you could try the one-click back to stock (realizing that you're having connectivity issues, I'll get to that in a second).
When you connect the phone in download mode to ODIN, does the yellow COM:# show up?
If you have tried ODIN on your Vista computer, try running ODIN as Administrator.
I've had some luck in the past getting the phone to be recognized (assuming Froyo) by doing this:
1. With nothing connected to computer, start ODIN (one-click to stock would be good).
2. Pull battery on phone.
3. Reinsert battery, but do not power on.
4. Hold Vol+/Vol-/, and insert USB cable.
5. Wait for it to kick into download mode, release buttons, and wait again.
6. See if ODIN recognizes it.
Click to expand...
Click to collapse
Thats my problem, the cappy does not see that there's an EX SD card there at all? says no files, but i've tried to push a cognition rom to the EX SD and use CWM to flash it to get it to boot, but the phone cannot see that there's an EX SD, but the SD card is fine, even my vibrant used it..
ODIN as ADMIN? tried that and nothing, still no yellow com port,
i know how to use odin, as my VIBE has been "Bricked" a few times lol
the vol up/down button combo does nothing, just shows up as a charging screen, the only way i can get the phone to download mode is through CWM.
the phone is running a FROYO based cognition ROM. or that's what her bf put on there.
This may sound stupid and simple but is the device set on mass storage from the settings menu? If you know.
Also have you tried mounting your sd cards in CWM?
Rhiannon224 said:
This may sound stupid and simple but is the device set on mass storage from the settings menu? If you know.
Also have you tried mounting your sd cards in CWM?
Click to expand...
Click to collapse
lol THATS MY PROBLEM> the phone thinks it boots normally, but i cannot get the settings menu. like the "SETTINGS APK" file was deleted when she formatted the SD!
but i was just playing around and i got google voice search to pop up!
then from there i used my WIFI and setup the google settings, then i went to the market grabbed CWM and used the cognition rom i've already downloaded, and used it!
then the GREEN CWM booted, and it still cannot MOUNT EX SD card. so the flash failed.. HMMMMMM
As of now i am gonna go into the rom i DLed (cognition) and try to DL Root explorer and hard push the Settings.apk file to the system. HOPEFULLY from there i can get my settings back to restore the phone.
Realizing that it's a long shot at best due to connectivity issues, have you tried using ADB?
If so, you could push the ROM you need to the internal SD.
so, used root explorer to move the NEW cognition froyo rom from the EXternal SD to the INTERNAL SD. from there i used CWM recovery to flash the rom, the rom flash was successful, but now the phone is stuck in bootloop on the AT&T world phone screen.
and CWM will not LOAD. FML
Looks like i'm gonna have to take this apart and get to the internal SD card. =/
Can you get to CWM with the Vol+/Vol-/Power combo - hold those past one AT&T screen and when you see the second one, let go?
Adb was not an option at that point, the phone couldn't recognize it even had a phone attached to it.
but now that i'm stuck in bootloop and with no CWM recovery OR DL MODE, yeah the jig isnt' workin... HAHA
i guess its just a paperweight now.. Owell, i tried.
i held it for about 3 mins... lol and the jig i got for my VIBRANT isn't workin either. I didnt know these phone's can lose the 3 button combo reset? i often flash I9000 roms to my vibe, thats why i have a jig, but i didnt think cappy's would do that unless i flashed an i9000 rom to it? lol
Just because I'm not sure if you tried it - have you tried plugging the cable into a different port on your computer? If it's not one directly connected to the motherboard, that can sometimes cause problems getting the phone to be recognized.
Also - does the phone show any signs of recognizing there is a cable inserted (like charging)?
tried every port. No the phone only acts as if it wants to display the batt charging symbol, but does not show, I cant believe it, i actually think i bricked a galaxy s.. haha
Another long shot, but you could try the One-click unbrick. Since it's Heimdall-based, there's always a chance.
Wow, didnt know that even existed. Definately gonna be useful for my Vibrant, haha i'll give it a shot.. THANKS, i'll report back after i try it.
I hope it does something. With the connectivity issues you're seeing it's starting to sound a little like hardware issues.
I'm going to throw out a checklist of stuff, knowing that you are already experienced with ODIN and ROM flashing, simply because I know I usually can use some sort of checklist to make sure I've caught everything.
- Redownloading/reinstalling drivers, rebooting before connecting phone
- Redownloading/reinstalling ODIN package
- Redownloading ROM to flash
- Hold V+/V-, inserting USB cable
- Remove battery, hold V+/V-, insert USB, insert battery
- Hold V+/V-/HOME softkey
- Hold V+/V-/HOME/Power
- If download mode reached, allowing phone to sit connected for long time
- If download mode reached, connecting phone after opening ODIN
- If download mode reached, connecting phone before opening ODIN
- If download mode reached, connecting phone after ODIN, disconnecting, reconnecting phone
That's all I can think of for a checklist of stuff to try/retry.
I appreciate the help but i've tried all of those options several times, The jig did work to get it into DL mode, but from there i'm still in the same **** position, my computer will not recognize that the phone is connected.
Is it possible that the phone somehow lost its drivers? what i mean by that is, the phone acts different with different USB ports, completely.
On one port it says unknown device, another USB android composite device.
Its as if the phone's changing as i change ports. Very FRUSTRATING!
i think it could be a hardware issue myself, but how could a corrupt drive work so well? To the T every time i've used the jig DL mode fired up, but my computer still cannot find the drivers to run it. Hell i've even tried using winusb drivers package to force install the phone, still no avail.
Like i said, I really appreciate the input, I figured if i couldnt figure it out, someone on here had some EXP in doing this lol i've just never had a driver problem give me so much trouble. IDK, bout ready to turn this paper weight into a pile of ash.
If you can get into cwm, have you tried doing another hard reset/factory wipe?
Thats the problem, earlier i COULD get into CWM, and hell i flashed the new rom perfectly!
now it is stuck bootlooping, therefore i just used the Jig, and first few times it didnt work, now its stuck bootlooping, download mode is attainable, and still NOT connecting to my pc via usb.
mrhaley30705 said:
If you can get into cwm, have you tried doing another hard reset/factory wipe?
Click to expand...
Click to collapse
Nvm, reread your post. Have you tried flashing a different rom?
PelvicThunder said:
Thats the problem, earlier i COULD get into CWM, and hell i flashed the new rom perfectly!
now it is stuck bootlooping, therefore i just used the Jig, and first few times it didnt work, now its stuck bootlooping, download mode is attainable, and still NOT connecting to my pc via usb.
Click to expand...
Click to collapse
Try a different computer? also, which version o of odin are you using? I've found 1.3 & 1.82 to work best.
Hello everyone I am sure that there is a lot of this thread going.
But I think mine is even worse.
the problem:
I rooted the device, everything worked fine ( did it with card reader - because my pc can not recognize the device had the problem a long time ago, somehow it worked then, but does not now, giving me the code 10 and 43
I think my USB port on the SAMSUNG might be damaged, because it does recharge but wont connect at all, tried kies, tried all the debugging modes, drivers, turning off the computer, rebooting all that stuff..)
The main problem is I flashed the cwm, rebooted, worked fine, then I clicked the do Backup thing and from then I can only go to yellow "downloading" or samsung logo, cannot even use that "Odin" because my USB is apparently damaged.. Any Ideas at all other than taking the phone and throwing it into the dumpster?
it is gt-s5830
my system is Win7-64bit
any help will be deeply appreciated ...
sincerely Fariel2012
Samsung logo freeze, cant recovery, can download mode (cant join to pc)
try with different usb cable
daniga74
Fariel2012 said:
Hello everyone I am sure that there is a lot of this thread going.
But I think mine is even worse.
the problem:
I rooted the device, everything worked fine ( did it with card reader - because my pc can not recognize the device had the problem a long time ago, somehow it worked then, but does not now, giving me the code 10 and 43
I think my USB port on the SAMSUNG might be damaged, because it does recharge but wont connect at all, tried kies, tried all the debugging modes, drivers, turning off the computer, rebooting all that stuff..)
The main problem is I flashed the cwm, rebooted, worked fine, then I clicked the do Backup thing and from then I can only go to yellow "downloading" or samsung logo, cannot even use that "Odin" because my USB is apparently damaged.. Any Ideas at all other than taking the phone and throwing it into the dumpster?
it is gt-s5830
my system is Win7-64bit
any help will be deeply appreciated ...
sincerely Fariel2012
Click to expand...
Click to collapse
Hi there
you will need to give a usb jigg service to your device and then flsah it back to stock using odin
SGA s5830 stuck @ boot logo
I follwed these steps before it stuck @ boot logo
1 rooted phone through root_S5830.zip file
2 then used 6.0.4.6-cooper_fix.zip cwm recovery
3 decided to flash Touchwiz-Resurrected_ROM_V1.0.zip rom
4 followed all steps to flash thrrough CWM recovery
phone reebots samsung.com logo>> samsung boot animation shows up>>samsung name appears again keeps glowing and phone restarts!!!
after it I tried 6-7 different roms then i tried to flash through odin but wasnt able to do so but failed the device showed up in odin but wasnt able to flash stock rom
then i decided to go for Phil touch recovery I installed Philtouch recovery and tried to flash a custom rom now I'm stuck again at boot name GALAXY ACE s5830 nothing goes further!!!
I searched over XDA and some guy quoted this problem is solvable by using odin and putting phone in downloading mode (vol- button+home button + Power on ) I am able to put my phone in downloading mode, but when i conncet it to PC it says USB device not recognized WTF!!!!!???? 10 mins ago i connected my Phone using same cable same port same odin now this ***** appears ???
I swapped PC's, Cables, ports everything nothings working , phone wont start stuck @ boot logo pls help ASAP :crying:
That's it.. You have hard bricked your phone that's dead recovery and dead download mode. Give your phone the usb jigg service which will force it to go to either the download mode or the recovery mode whatever you want.