Database Develop

Magnetic Mini(malist) Mount

Do I get the award for the simplest mount?
Basically what I've done here is take the self-adhesive metal plate tomtom supply for securing their gps 'mice' to the car. It holds my Advantage just beautifully. I thought it might swing around a bit on its axis because the plate is so small but if you sit the end of the advantage that has two magnets (either side of the keyboard connector) it seems to hold in place pretty rigidly. I've tried a few twists and turns as well as emergency stops and not lost it yet. It might be the case that the screen would flop off the keyboard at a very rapid deceleration but it hasn't happened yet. I leave the cover on for convenience and to cushion its fall if that does happen.
So far it seems pretty secure but use at your own risk.
Cost approx GBP£5 (USD$10) plus tax, postage etc and ultimate convenience. No sucker bases, swing arms etc and it sits right where its needed for power etc.
I had mine left over from a previous tomtom installation but similar plates are apparently still available as spares e.g. from here.
I'm not sure mine is magnetic, by the way, it may just be metal.

The same I thought...but I sold TomTom gps years ago...

inframan said:
Do I get the award for the simplest mount?
Basically what I've done here is take the self-adhesive metal plate tomtom supply for securing their gps 'mice' to the car. It holds my Advantage just beautifully. I thought it might swing around a bit on its axis because the plate is so small but if you sit the end of the advantage that has two magnets (either side of the keyboard connector) it seems to hold in place pretty rigidly. I've tried a few twists and turns as well as emergency stops and not lost it yet. It might be the case that the screen would flop off the keyboard at a very rapid deceleration but it hasn't happened yet. I leave the cover on for convenience and to cushion its fall if that does happen.
So far it seems pretty secure but use at your own risk.
Cost approx GBP£5 (USD$10) plus tax, postage etc and ultimate convenience. No sucker bases, swing arms etc and it sits right where its needed for power etc.
I had mine left over from a previous tomtom installation but similar plates are apparently still available as spares e.g. from here.
I'm not sure mine is magnetic, by the way, it may just be metal.
Click to expand...
Click to collapse
Great idea. So in theory, any magnetic adhesive strip should serve in the car. Hmmm....
Maybe these
http://cgi.ebay.co.uk/Magnetic-Stri...yZ123866QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
Or cheaper ones!

inframan said:
Do I get the award for the simplest mount?
Basically what I've done here is take the self-adhesive metal plate tomtom supply for securing their gps 'mice' to the car. It holds my Advantage just beautifully. I thought it might swing around a bit on its axis because the plate is so small but if you sit the end of the advantage that has two magnets (either side of the keyboard connector) it seems to hold in place pretty rigidly. I've tried a few twists and turns as well as emergency stops and not lost it yet. It might be the case that the screen would flop off the keyboard at a very rapid deceleration but it hasn't happened yet. I leave the cover on for convenience and to cushion its fall if that does happen.
So far it seems pretty secure but use at your own risk.
Cost approx GBP£5 (USD$10) plus tax, postage etc and ultimate convenience. No sucker bases, swing arms etc and it sits right where its needed for power etc.
I had mine left over from a previous tomtom installation but similar plates are apparently still available as spares e.g. from here.
I'm not sure mine is magnetic, by the way, it may just be metal.
Click to expand...
Click to collapse
This is great! Can't believe I didn't think of it. DUH! Great job on reporting this.
I'm thinking of going to the hardware store and getting a small L shaped metal "plate" and put velcro on the back of it. Should hold things nicely.
Like the way you kept the case on it. I would have done exactly the same thing. Not only does it help but I would be too lazy to remove it all the time when I got into my vehicle.

magnetic adhesive strip
Actually I tried magnetic adhesive strip, but it is quite weak ... Found out a normal metal ruler is better magnetic adhesive, as the keyboard is quite a strong magnet

@topic
Its really a good idea... I might try it...

Im using this one
it's fantastic and very solid

Aluminum case and signal issues?

Hey guys, I was just about to purchase this case but then started wondering if it would adversely affect my signal strength so I thought I would jump on here and see if any of you have used an aluminum case and what the results were...
Thanks for any info, you guys rock!

It has a very good possibility of affecting the signal since the antenna will have a clunk of metal around it. But I dont have any first hand knowledge. Why not just get a plastic case. They effect it less.

I really want a case that has a door with a window on it..do you know of any plastic one?
Anyone else have any experience with aluminum cases?

Perhaps I am a pioneer in the area of aluminum cases and the HTC Mogul...or perhaps no one is paying attention to this thread because it's posted in the wrong area. I don't suppose an admin could move this over to the accessories sub forum could they.
Aside from this, where is the antenna located in the mogul? I'm thinking that if I do end up with signal issues I will cut slits the length of the antenna in the case.
Any info on this would be greatly appreciated!

conradcliff said:
Perhaps I am a pioneer in the area of aluminum cases and the HTC Mogul...or perhaps no one is paying attention to this thread because it's posted in the wrong area. I don't suppose an admin could move this over to the accessories sub forum could they.
Aside from this, where is the antenna located in the mogul? I'm thinking that if I do end up with signal issues I will cut slits the length of the antenna in the case.
Any info on this would be greatly appreciated!
Click to expand...
Click to collapse
Sounds pretty cool, can you link us to the particular case mentioned? Other than that I have no experience with metal (aluminum is considered a metal for the banterers) cases either. Personally I would stick to plastic, but sounds neat.

There's a link to it in the first post, but here it is again.
I've been walking around with an ipaq 2215 for the last 5 years with an aluminum case and that thing has saved my life on many occasions.
The plastic would be ok too I think, but only if I could find one that had a door that closed over the screen..
Who do you think I should talk to to get this moved over into accessories? I didn't even realize there was an accessories category when I posted this..

conradcliff said:
There's a link to it in the first post, but here it is again.
I've been walking around with an ipaq 2215 for the last 5 years with an aluminum case and that thing has saved my life on many occasions.
The plastic would be ok too I think, but only if I could find one that had a door that closed over the screen..
Who do you think I should talk to to get this moved over into accessories? I didn't even realize there was an accessories category when I posted this..
Click to expand...
Click to collapse
That case is awesome. I really like it. Interested to see if it ruins the signal quality, or possibly enhance it lol I dont know.. It looks properly designed, I am sure the manufacturer took the antenna location into consideration. I would go for it. Let me know how it works out, hopefully by then one is still available. I can grab one myself.
I will have this moved for you.

Thanks for getting this moved for me Ryan..yeah, I think I'm going to purchase the case within the next few days unless someone pipes in with a negative review.
In the meantime, does anyone know where the antenna is located in the 6800?
Thanks for any help!

So, I came in here to bump the thread up one more time before I bought the case, but it was still at the top...doesn't seem like people are too concerned about Titan accessories any longer
I guess 150 views is enough though, I think I'm just going to bite the bullet and buy.
Will update once I've tested in the low signal areas that I frequent.

I had the exact same case for my xv6700 and never had any signal issues. The case worked well and kept my 6700 looking brand new!
I really liked the lexan screen cover.
I tried the seidio rubberized case for my titan. it worked awesome for about 10 months until the little tiny tabs that held it on broke off. Only a 90 day warrenty so SOL. Now I use a cudora pouch.
So let me know how the aircraft aluminum one fits!!

That's great to hear! I'm going to order it tonight and maybe upload some pics when I get it..

hi conradcliff
dont forget test review the case (how about the look, size etc) and upload the pict, i want to buy also, but it seems need 2 week to deliver it to my country

Oh I most certainly will..I'll also post the coupon code they gave me for 10% off, hopefully it will work for anyone.

Initial Review: Monaco Aluminum Case for Mogul/6800
Short answer: A well designed, sturdy case well worth the ~ $20 price. I'll add some photos soon. Sorry if I stepped on anyone's toes who intended to write one of these up, but hey, two opinions are better than one!
I've had three of these cases for three separate Sprint 6800's. Two black, one silver. For those familiar with Monaco Aluminum Cases (they made/make these for other phones, such as the 6700), this embodiment is just as good.
Pros:
Very solid design - this case can easily outlast the life of your phone. Aside from slight exterior discoloration, dings, and scratches, this case should easily withstand all normal, day-to-day use.
Inner liner - this case includes an inner liner made of neoprene that protects the phone from minor scratch/abrasion marks; that provides a very snug fit for the phone; and provides *minimal* fall protection. Two-story drops and projectile usage by angry girlfriends are not protected.
Access - the case provides access to all buttons, dials, interfaces (except for touch screen & slide-out KB). Luckily, almost all functionality of this phone can be effectuated without the touch screen (not the TP, grrrr), so you will not have to open the case too often, which is very nice. When you do open the case, the keyboard slides over the open top of the case nicely.
Vents (Air/Signal) - there are vents on the top, back, and right side of the case for air and/or signal paths. I've experienced no signal difference, or even heat difference, with this case. I'm sure it does insulate the phone to some degree, but it's minimal.
Belt Clip - the case comes with a belt clip and swivel that are relatively secure and convenient. I've had one belt clip split (the plunger portion), but it is still very usable. You don't have to use them, but I do. The round swivel that screws into the back of the case provides a nicer grip of the phone, IMHO. If you don't like either, you don't have to use them.
Cons:
Weight - it does add weight to your phone. It's not extreme, but holding the phone for extended periods of time may prove annoying by some with this extra weight. I don't mind it at all, and I have a headset and use speakerphone anyhow.
User Adjustment Required - Out of the box, this case is NOT ready to use! You absolutely must gauge how well the metal clip engages the main body of the case. Every case I've received required me to slightly bend the clip inwards to provide a stronger hold. If the hold is too weak, brushing against the side of the case (by your arm when walking with the case attached to your waist side, or by anything you may brush against) can result in your phone falling out to the ground. So, adjust the clip right away, and ALWAYS, periodically check it, as repeated opening may loosen the hold over time. Also, when wearing this case attached to the side of your hip, attach it to your left side so the metal clip and catch of the case are facing behind you. This way, brushing against something while you're walking will not accidentally open your case allowing your phone to drop out.
Plastic Cover - this cover can scratch. I tried placing a screen protectors over it, but they would never stay. The oil from your face/hands/etc, along with the lack of a frame protecting the edges of a protector from friction are mostly to blame. However I've learned that with a little care, the plastic screen can survive everyday use quite nicely.
So, I highly recommend this case!!
10% off coupon code -> EIWQC1257830
"Simply insert the coupon code during our checkout process and instantly save 10% off the merchandise.
You can use the coupon up to 5 times. This code will expire after 60 days [from 10/7/09]."

There's more to know though so don't buy until you get my review..hopefully tomorrow.

I've become one of the Angry Birds because of the poor quality of NC's USB Cables.

I know this post is quite useless. I just wanted to vent out my frustration.
I just got off the phone with a B&N rep after 20 minutes of talking--because the rep kept beating around the bush and kept placing me on hold--and was told that I needed to callback on Monday to get the tracking no. for my 2nd--yup, this happened twice before--USB cable replacement. Yup, it broke again like the first one I got included with the NC--SIMPLY BECAUSE OF IT'S POOR QUALITY.
In generic micro USB cables, you would notice that most of them are made of rubber material, especially the one covering the tiny metal tip that you insert on the device's USB port, which makes them quite durable. Even if you bend it intentionally multiple times, the metal tip will not be affected that much. Only downside is, it doesn't fast charge the NC. In my experience, it takes a day and a half (about 36 hours) to be able to charge the NC fully. And yup, my NC is now turned off for a week (and counting).
The NC's stock USB cable however is made out of a gloss plastic material, probably to give way to the LED? light indicator? Downside is, it gets cracked/chipped off easily whether it was done unintentionally or not, because of the plastic material not being 'hard' enough, and that's where most NC owners like me are getting pissed off.
You have to be very careful whenever you charge the NC--you need to make sure that it's on a flat surface, not on a surface where it can sink itself say for example, a foam bed, so that the cable will not 'sink' with it in and put pressure on the metal tip, finally chipping off the plastic coating.
Do you guys know of any alternative that can fast-charge the NC like it's stock USB cable? Does anyone have the ability to modify the NC's stock USB cable to coat it with rubber or something to make it more durable?
I'm sure there are others who are experiencing these things. Hope we can gather around and start a discussion about getting a permanent fix. Maybe rally at a local B&N store or something, I dunno.

Well, a cheap and quick bit would be to wrap it with electrical tape. If you have an electronics store or Radio shack carrying it, there is also something called shrink tubing. this is a rubberish tube that when carefully heated with a heat gun (not a blow dryer) or a lighter, will shrink down around wires, or plastic.
But, I am rather annoyed with this serious design flaw as well. Would be nice if B&N either recalled these cables with a properly designed one, or get a 3rd party available to handle that.

I was thinking of reinforcing the plug end of the cable by encasing it in a big wad of epoxy putty.

epoxy putty usually cures to something a bit too brittle for what this really needs. As the OP said, the plastic on the plugs are really way too brittle for what it's meant for. other than those things, the other option I can think of is some of that latex dip sold in some hardware stores, or sex shops. wrap the metal bit in tape, then give it a few dips, let it cure, then carefully cut the tape off. instant rubberized plug. could even carefully cut an indicator window for the charge light.

heat shrink tubing sounds best. will try that. you can get it from home depot or lowes. get the multiple size package. it is really best to use a heat gun. if you dont know what your doing and use a lighter you will burn right through the heat shrink.

It sounds like you might be looking for Sugru. It hardens to a rubbery flexible consistency. There's also a how to floating around the web on making your own using caulk and ...baking soda? I think?
For that matter, a flexible clear caulk might do the trick.

I was thinking that RTV silicone (downside is long cure time) or maybe hot melt glue would be worth a try. Either one would be translucent enough to see the LED color. The Sugru looks interesting, although opaque like heat shrink tubing.

You could probably use something like Scotch Coat (more or less liquid electrical tape..) or plasti-dip perhaps?
*I'm still waiting on my NC to arrive. So, I'm not sure exactly which portion of the connector you're talking about. If it's the entire outside portion that is typically metal... this is normally a chasis ground which equalizes the chasis potential between the NC and whatever it's plugged into..., and really shouldn't be coated with anything

I ordered this off Amazon with the intent of fixing several things in my house. I was going to use the clear for the tip of the charger.
http://www.amazon.com/gp/product/B0027JIEPU

I think the shame of it is that all they had to do was use a strain relief sleeve like one of there:

Using the shrink tubing-
1. make sure you get a size large enough to get around the connection end.
2. Measure out a length. you want at least from the bottom of the N light to about 1/2 inch past the nub where the cord goes into the connector.
3. Slip the tube into place
4. Using a heat gun or lighter, carefully shrink the tube into place (NOTE: with a lighter, keep the flame moving, don't let it linger too long or you'll melt something)
5. If the resulting reinforcement doesn't seem enough, feel free to add another layer or 2.
WHAT DOES THIS ACCOMPLISH?
Well, most of the failure pictures I have seen, as well as the failed cord of my own, it seems the plastic is too friable (meaning it cracks really easy) to handle the stresses put on it at that end. Most of the cracks and fractures take place below the N, towards the cable side of the connection.
By adding this, it not only adds a semi flexible reinforcement around where it likes to crack up, it also stiffens and immobilizes a stretch of the cable, relieving a little of the stress that can happen in that part.
While other things might do the trick, and even electrical tape could do, this tubing is about the best option I've seen so far.

Srilania said:
While other things might do the trick, and even electrical tape could do, this tubing is about the best option I've seen so far.
Click to expand...
Click to collapse
Heat shrink tubing isn't a bad idea. I don't know how readily available it is in consumer stores and stuff... but I know I've used the Heat shrink tubing with the glue inside on quite a few connectors (higher end coaxial/heliax connectors tend to come with it). It's a bit thicker and more durable than typical heat shrink tubing, and the glue holds it solidly in place.

I used scotch tape. ugly, but it works.

Heat Shrink tubing shouldn't be too hard to find, most any electrical / hardware store should carry it, even Wal-mart will have it from time to time in the automotive section.

A better option may be plastidip. It gives a thick rubnery coating.
Sent from my NookColor using Tapatalk

After having a Nook Color for less than 6 months, mine just broke this morning! I would do without the LED indicator for a durable rubber casing.

Imbroglio said:
I was thinking of reinforcing the plug end of the cable by encasing it in a big wad of epoxy putty.
Click to expand...
Click to collapse
Epoxy works very well actually, but you need to put it on the inside, not the outside. Split open the plastic cover. Clean it up so it fits back together cleanly. Mix up a batch of translucent 5 Minute epoxy and completely fill the cavity with epoxy. Fit it back around the cable and secure it with a clip or clamp of your choice. A small binder clip works perfectly. After about 5 or ten minutes you can remove the clip and use an exacto knife to clean up the excess. Clamp it up again and
let it cure for 12 hours or so. Works well for me.

Triple wall heat shrink is just what you need. A heat gun (not a lighter, it won't work well) is the way to go. A hair dryer most likely won't have the heat needed.
I use the stuff in my home business and have tons of it...if you need some let me know!

I bent the male end that plugs into the nook unit... I Pressed the male end against a counter in my kitchen so it was bent back into place, put a few spots of super glue (the kind you get at the dollar store) and waited overnight for it to dry. good as new, no more wiggle or bend in my usb end.

Your thoughts on magnetic holsters

Im looking for a holster, i found some but most have a magnetic closure. Im not sure if its ok for our phones so i just wantes your thoughts or experience with it. I use samsung pay every day and i dont want any sensor to be off because of the magnets.
Maybe im a little paranoid over it because it probably takes an extremely powerful magnet to cause any harm but im not willing to test it out lol

None of the magnetic items for the phones will cause any harm to your phone.
You may notice that the stylus doesn't work where the magnet is, but it will work just fine when you move the magnet.

As a Samsung Experience Consultant, I do not recommend anything magnetic, I think they mess with the device internals.

kmarx said:
As a Samsung Experience Consultant, I do not recommend anything magnetic, I think they mess with the device internals.
Click to expand...
Click to collapse
You do know many manufacturers use magnets in their devices and accessories, including Samsung and Apple, right? Every Apple smart case / cover utilizes magnets and (as much as I love Android) I can honestly think of no more reliable tablet than the iPad.

kmarx said:
As a Samsung Experience Consultant, I do not recommend anything magnetic, I think they mess with the device internals.
Click to expand...
Click to collapse
You think or you know?
You should only be putting out info if you know. If you don't know, and it is clear you don't, then you should not speak on a subject.
Magnets will in no way harm the phone unless you are using super powerful magnets, what you use to hold the phone to a dock and things like that won't bother it in the least bit.

I do not recommend any of the Samsung Flip Cases to customers because I have seen them cause problems with devices before. I do not recommend magnetic closures because I have seen them cause problems with devices.
flyingwolf said:
You think or you know?
You should only be putting out info if you know. If you don't know, and it is clear you don't, then you should not speak on a subject.
Magnets will in no way harm the phone unless you are using super powerful magnets, what you use to hold the phone to a dock and things like that won't bother it in the least bit.
Click to expand...
Click to collapse

kmarx said:
I do not recommend any of the Samsung Flip Cases to customers because I have seen them cause problems with devices before. I do not recommend magnetic closures because I have seen them cause problems with devices.
Click to expand...
Click to collapse
What sort of issues have you seen?
It seems strange that Samsung would release a product that would interfere with one of its flagship products and sell it as an accessory.

Mayonesa said:
Im looking for a holster, i found some but most have a magnetic closure. Im not sure if its ok for our phones so i just wantes your thoughts or experience with it. I use samsung pay every day and i dont want any sensor to be off because of the magnets.
Maybe im a little paranoid over it because it probably takes an extremely powerful magnet to cause any harm but im not willing to test it out lol
Click to expand...
Click to collapse
I'm not sure if this is specifically what you're asking about, but I've been using a Scosche MagicMount (http://amzn.com/B00I608BJ8) for my car dash and love it! I lay the larger metal plate (it comes with two sizes) at the bottom of my case, oriented where the longer sides are parallel to the bottom of the phone (let me know if you need a picture). I don't stick the plate to my phone, but rather set it inside my case. It turns out to be the perfect length and height for the Note 5. Wireless charging and Samsung Pay still work great. I used that picture of the Note 5 where someone made the back of transparent to make sure the wireless charging coil inside the phone does not over lap with the metal plate that comes with the mount.

I bought a nice leatherette case for my Note 5 only to find that the S-Pen does not work on the right hand side where the magnet is. I took it off immediately and went back to my Body Glove case.

flyingwolf said:
You think or you know?
You should only be putting out info if you know. If you don't know, and it is clear you don't, then you should not speak on a subject.
Magnets will in no way harm the phone unless you are using super powerful magnets, what you use to hold the phone to a dock and things like that won't bother it in the least bit.
Click to expand...
Click to collapse
I purchased a wallet case on eBay. I noticed there were areas on the screen that wouldn't work. When I flipped the removable phone case there were 6 magnets...three on each side to hold the phone in the wallet. These magnets are small, but the impact was terrible! I I'm attaching pictures of me using the s pen to find the areas on the screen and the back of the phone case.

charlesrogers74 said:
I purchased a wallet case on eBay. I noticed there were areas on the screen that wouldn't work. When I flipped the removable phone case there were 6 magnets...three on each side to hold the phone in the wallet. These magnets are small, but the impact was terrible! I I'm attaching pictures of me using the s pen to find the areas on the screen and the back of the phone case.
Click to expand...
Click to collapse
-Sigh-
Like I said. "Magnets will in no way harm the phone"
This isn't harming your phone, it does do as you have seen which is a TEMPORARY issue and has already been discussed, it will cause no permanent harm to the phone.

I don't know about magnetic holsters but magnetic car mounts most definitely YES. I've used many holsters over the years, for all kinds of types of phones. I haven't really thought about it till I saw this post. My buddy has a good magnetic car mount for his s7 edge, but I don't really know anyone at the moment that's using a magnetic holster. Just my opinion though, the last time I used a holster was way back in January and it was actually pretty good. It was a best buy branded platinum, with kickstand holdster and case like a 3 in kind of deal but not magnetic. It fit could on my belt clips for my jeans and suit pants. Good luck

bought the Bracketron brand at best buy, the magnetic part is on the mount, it is a metal plate stick to your phone so no interference from the magnet, not owning a note 5 tho.

I put in some small tin paper cutouts INSIDE my note 5. I took the back cover off, peeled the sticker with the color/logo and spraypainted it a nice black then just glued the tin paper inside of that. Then I took a flat wireless charger and added neodymium magnets to it, modded it to be as small/thin as possible then covered it up with some black thin leather I bought from Michaels. I mounted it up to my car's console and now I just plop the phone onto it and it sticks tight and fast charges, no wires or case. Worked perfectly, but in hot weather the leather would become a bit slippery so it would slip off, but I fixed that with a couple of very small circular double sided gel tape on the bottom just to provide a bit of friction. I've ridden like this for the past 5 or 6 months and it doesn't slip or fall off at all, heavy bumps, hot weather, nothing dislodges it.
The only thing that doesn't work is the spen, and that's only directly over the magnets, but I wouldn't write on it anyway while it was mounted. Otherwise I've had zero difficulties with it. I'll post up pics if anyone is interested, but it's a bit frankenstein looking.

Case with charger dust cover

I know this is a longshot due to the relatively small number of accessories, but I'm looking for a case that somehow covers the charging port. After a lot of reading about how the phone is actually waterproof despite the lack of ip68 rating, I plan to take it surf fishing with me. I'm not going to dunk it in saltwater or unnecessarily expose it to waves and spray. I am worried about sand, which tends to get everywhere including all over the inside of my car. The salty air tends to make the sand stick to everything and I don't want to get it into the charging port and have it break something while plugging/unplugging the charger. So any suggestions would be greatly appreciated.

McLovin69 said:
I know this is a longshot due to the relatively small number of accessories, but I'm looking for a case that somehow covers the charging port. After a lot of reading about how the phone is actually waterproof despite the lack of ip68 rating, I plan to take it surf fishing with me. I'm not going to dunk it in saltwater or unnecessarily expose it to waves and spray. I am worried about sand, which tends to get everywhere including all over the inside of my car. The salty air tends to make the sand stick to everything and I don't want to get it into the charging port and have it break something while plugging/unplugging the charger. So any suggestions would be greatly appreciated.
Click to expand...
Click to collapse
I haven't seen one that covers all the ports. Like you said the selection is kind of limited for smaller "niche" types of phones such as the compact. The only thing I know of that will protect all the ports and also make the phone waterproof is the Armor X Soft Case. Doubt it's what your looking for but it might be something right up your alley. https://www.armor-x.com/ag-w1-z5-sony-xperia-waterproof-soft-case-cover-for-x-xa-performance-compact.html

Thanks. I have one of those already. The problem with those is all the fumbling around opening and closing the pouch.
Actually I'm highly confident that the xc is waterproof. But like I said I'm worried about grinding sand into the charging port and wrecking something. .

Nillkin has one that covers charging port. I bought mine on ebay for 5€. Check it