Related
so for the past month my screen has been dead when it is in portrait mode. it would only turn on if i open my keyboard in landscape mode. if i close the keyboard the screen will freeze. the screen is still responsive in portrait mode though, for example, i can still slide to unlock even though the screen is off. i also can't turn on the phone unless it's the keyboard is on til i get to the lock screen.
also my phone has been restarting itself a lot this past month. usually i notice it does it when i walk and it's in my pocket. but it also happens even when i'm just using the phone, it'll randomly restart itself.
is there any solution to my problems or is it a lost cause?
This sounds like a ROM/overclocking issue. If you're overclocking, turn your levels down a little bit. Flash a different ROM if that's not the case. And if neither of those work, rip her open and check and make sure everything is in their proper place. There are guides online that you can google.
Hi. my UK note (baseband N7000XXKK5, 2.6.35.7.N7000XXKKA, CF-root, stock ROM) has recently stopped turning the screen back on after a call (or during a call when I take the phone away from my ear to use the dial pad, go on speaker, etc.).
Normally the only way I can get the screen back is to hold the power key in until the phone reboots (though I've randomly managed to get it back sometimes, possibly when the other party hangs up and/or I'm pressing the power or home keys to try and get it back).
I've turned off the proximity sensor in settings meantime, and calls are fine in that state - but I don't want to waste battery and/or risk pressing stuff on screen with my head/cheek so I'm looking for a fix. Anyone else got this problem or suggestions for a solution?
I used the *#0*# test menu and chose "sensor". This gives a value of 0.0 for proximity until I put my hand within a few cm's of the sensor, at which point the screen goes green, the phone vibrates constantly and the reading changes to 1.0. Once in that state it stays that way when I remove my hand and doesn't change until I hit the back key.
Is the proximity sensor test intended to be a one-shot affair, or should it register 0.0 once I remove my hand?
My galaxy note is having a similar issue, however when I run the sensor test from *#0*#, I observed a different behaviour, where the proximity output says "1.0" and constantly vibrates all the time (which would explain the screen went black when a call comes in even if I put it on the table, as the phone constantly detects something)
sounds like yours is likely a hardware fault then. I ended up just leaving the proximity sensor disabled for calls and I don't really miss it. The only other thought I had was that my front cam has a load of dust built up under the display glass and it's adjacent to the sensor. I wonder if a layer of dust could trigger it?
actually I just re-ran the sensor test and it now toggles between 0.0 and 1.0 each time I move my hand over the sensor - so looks like in my case I have an intermittant problem. At least now I know how that test is designed to work. I will run it periodically to see whether anything specific is triggering my sensor to stop working.
OK, the following steps resolved my problem:
1. Remove microSD card and turn on the unit
2. Goto *#0*#, sensor test and verify that the issue is resolved
3. Put back in the microSD card
4. Repeat step to and now everything should be back to normal
Just rebooting the unit does not help (as I tried this before), but the above steps have fixed my problem.
I haven't seen this posted anywhere so I figured I would post for anyone having a similar issue with their One.
Recently my phones backlight stopped working. It would not work at boot or in the ROM. I tried flashing to stock and tried optimizing the proximity sensor, but no luck. It was clearly a hardware problem.
Not seeing any solution to this issue other than people saying it is the screen or the motherboard I decided to order a new screen.
Well installed the new screen, still no backlight. I was about to give up on it and just buy another phone, but I got the feeling that the light sensor may still be my issue. The backlight on the capacitive buttons would not turn on unless I helded down the power button to force shutdown. This meant the backlights for the buttons at least worked and something else in the phone was preventing them from turning on.
I decided to remove the light sensor from the daughterboard (opposite the power button connector). Booted it back up, and the screen came right on. The phone works great without it, other than auto brightness. The screen still turns off when against face during calls.
So long story short if your LCD and button backlights aren't working don't order an LCD or rule your phone dead right away. Open it up and take out the light sensor, it could be the culprit.
I'm going to order a new sensor and can update with results after installing if anyone is interested. In the meantime I'm using the phone without it, no hiccups so far.
htc one screen backlight issue
nsodmordex said:
I haven't seen this posted anywhere so I figured I would post for anyone having a similar issue with their One.
Recently my phones backlight stopped working. It would not work at boot or in the ROM. I tried flashing to stock and tried optimizing the proximity sensor, but no luck. It was clearly a hardware problem.
Not seeing any solution to this issue other than people saying it is the screen or the motherboard I decided to order a new screen.
Well installed the new screen, still no backlight. I was about to give up on it and just buy another phone, but I got the feeling that the light sensor may still be my issue. The backlight on the capacitive buttons would not turn on unless I helded down the power button to force shutdown. This meant the backlights for the buttons at least worked and something else in the phone was preventing them from turning on.
I decided to remove the light sensor from the daughterboard (opposite the power button connector). Booted it back up, and the screen came right on. The phone works great without it, other than auto brightness. The screen still turns off when against face during calls.
So long story short if your LCD and button backlights aren't working don't order an LCD or rule your phone dead right away. Open it up and take out the light sensor, it could be the culprit.
I'm going to order a new sensor and can update with results after installing if anyone is interested. In the meantime I'm using the phone without it, no hiccups so far.
Click to expand...
Click to collapse
hey
i'm having the same problem are you sure that it is a hardware issue and not the software issue my h/w buttons doesn't light at all and my screen stays black for some time after unlocking the phone it comes back but the brightness is too low
any suggestions would be appriciated
Mine was a hardware issue, the backlight did not turn on at all, even on the htc start screen. The capacitive buttons would only flash when holding down the power button. If ypurs is intermittent and your phone is rooted you cantry insralling an app fhat alows you to change the proximity settings, sorry, cant remember the name of the app i tried. If the app can't detect the sensor it is likely broken like mine was. If that doesnt work try a different rom.
If neither of those help it is likely a hardware issue.
i used the app both light senor and proximity sensor are working fine
any other tips that i can try
kingkri said:
i used the app both light senor and proximity sensor are working fine
any other tips that i can try
Click to expand...
Click to collapse
Sorry for taking so long to respond, just noticed your reply.
Did you ever get it working? If a different rom did not solve your issue maybe your sensor is just dirty. You could try cleaning it with a can of compressed air. Not sure how effective it would be, but it may help.
Hi @nsodmordex, my HTC One M7 is in the same situation as you describe, no backlight, but working. I'm going to try your suggestion of removing the light sensor, but I'm unable to find it, I'm not sure where the light sensor is.
Please, can you tell me which component is the light sensor? This is a photo of the daughter board:
htt ps://d3nevzfk7ii3be.cloudfront.net/igi/ALPJIMWqGsLwul5Y.huge
Thanks!
Found it... it's located behind the daughter board, at the two little holes of the front cover of the phone. I have removed it but no luck, the screen continues black, but the mobile is working good.
it seems a screen related problem, I'm going to try to change the screen and see if it comes to life again.
Drain battery
Hi all,
I also have this problem and found out that if I drain the battery completely and wait about 1 hour, it turns back on when I put the charger in the phone, if the screen doesn't turn on, drain and wait longer, if it does turn back on then power the phone. Do not wait till it has a little bit power because than it fails again and you must drain and wait again.
It works for me and I will make a video of it and post a link later.
Hope it works for you all!
Tip: use a led flashlight to see what's on the display
Ps. Stock m7
Whats the definitive solution for no backlight screen?
jvpag said:
Whats the definitive solution for no backlight screen?
Click to expand...
Click to collapse
Clean / replace the lightsensor
Dippie83 said:
Clean / replace the lightsensor
Click to expand...
Click to collapse
I had removed it and the backlight isn,t working
jvpag said:
I had removed it and the backlight isn,t working
Click to expand...
Click to collapse
Than the lightsensor is broken, are the contacts on the back of the sensor 100% clean, in my case it was dust that created the error.
Is the display not broken?
Dippie83 said:
Than the lightsensor is broken, are the contacts on the back of the sensor 100% clean, in my case it was dust that created the error.
Is the display not broken?
Click to expand...
Click to collapse
The display is ok because I can see what is on the phone with the LED flash of a Galaxy S2 so I think that the display is not broken.
The backlight doesn´t turn on with the light sensor and without it either. But i can remember that the last time that it worked the Autobrightness was fine
Edit: I tried rebooting on fastboot and recovery via ADB and the screen is without backlight too
PD: Sorry for my English
jvpag said:
The display is ok because I can see what is on the phone with the LED flash of a Galaxy S2 so I think that the display is not broken.
The backlight doesn´t turn on with the light sensor and without it either. But i can remember that the last time that it worked the Autobrightness was fine
Edit: I tried rebooting on fastboot and recovery via ADB and the screen is without backlight too
PD: Sorry for my English
Click to expand...
Click to collapse
In my case, if it worked it was ok also the autobrightness.
I think the sensor is broken and if you replace it the backlight comes back on (sensor is +- 10€ in holland)
Just give it shot
Have you tried the battery drain?
Hehe my english is also not very good
Dippie83 said:
In my case, if it worked it was ok also the autobrightness.
I think the sensor is broken and if you replace it the backlight comes back on (sensor is +- 10€ in holland)
Just give it shot
Have you tried the battery drain?
Hehe my english is also not very good
Click to expand...
Click to collapse
But as I read, if I remove the sensor and turn on the phone without it, will it work?
In this moment the phone has 0% battery and if I plug the charger i can see the red light and if i use a flashlight, i can see "the battery with the lightning" on the screen
jvpag said:
But as I read, if I remove the sensor and turn on the phone without it, will it work?
In this moment the phone has 0% battery and if I plug the charger i can see the red light and if i use a flashlight, i can see "the battery with the lightning" on the screen
Click to expand...
Click to collapse
No i dont think thats gonna work, push the power button (whitout charger) every time till the battery is really empty, than wait an hour.
If you connect the charger and the screen will not turn on, wait longer. a night is even better.
If the screens comes on then turn direct the phone on dont let it dim itself or else you can wait again.
This worked in my case but my lightsensor was dirty and after a cleanup it worked normal and it stil works.
Dippie83 said:
No i dont think thats gonna work, push the power button (whitout charger) every time till the battery is really empty, than wait an hour.
If you connect the charger and the screen will not turn on, wait longer. a night is even better.
If the screens comes on then turn direct the phone on dont let it dim itself or else you can wait again.
This worked in my case but my lightsensor was dirty and after a cleanup it worked normal and it stil works.
Click to expand...
Click to collapse
Okay, thanks, it worked once, but with the phone turned on and the backlight working, if the screen turns off, the backlight runs away again.
can you repeat point by point what i need to do?
when you say "drain" the battery, you mean leaving the phone on till it turns off? then what should i do? wait an hour and plug the charger to see if it works right? okay, and later if the phone turns on what i need to do?
jvpag said:
Okay, thanks, it worked once, but with the phone turned on and the backlight working, if the screen turns off, the backlight runs away again.
can you repeat point by point what i need to do?
when you say "drain" the battery, you mean leaving the phone on till it turns off? then what should i do? wait an hour and plug the charger to see if it works right? okay, and later if the phone turns on what i need to do?
Click to expand...
Click to collapse
By 'drain the battery' i mean continuously turning the phone on with a empty battery till it does nothing, not even vibrate.
It must be so empty that the phone not knows its a phone.
And yes if the screen comes on just power it on, thats it.
1 drain
2 wait
3 plug in charger
4 screen comes on
5 turn phone on
6 done
1 drain
2 wait
3 plug in charger
4 screen stays off
5 drain and wait longer
that are the steps that worked for me
Thanks @Dippie83 , it "worked" draining the battery and waiting forma a night to turn it on but when i turn on and i push the power button yo lock the screen, the backlight stops working
Any idea?
I can't get the New Gear VR to keep the orientation straight even when calibrating it in settings. Everything to see straight I have to put my head a little sideways. Even the darn Samsung Settings Menu is always crooked. Any advice? Thanks
Which phone are you using? Try using it with/without locking your phone orientation. If the phone's gyro is not calibrated, google for calibrating it for your phone. One way is to turn it off, lay it on a flat horizontal surface and then turn it on and let it boot completely as it lays there. Pick it up after 1-2 mins and check again.
Non rooted, T mobile branded 3 month old note 8. No water damange, no drops etc.
Using chrome one miniute, set the phone down to watch a movie on my tablet, picked up the phone to check messages and boom. Screen is off. The phone works, I can even answer calls because I know where the answer button is on the screen, haptic feedback works, all indicator lights work. The phone screen remains off.
Tried a soft reset (tried hard reset too the best I could being I cant see the screen) and the phone seems to reset based on the vibration and indicator light patters but the screen remains off. It's as if a physical connection between the screen and the brains of the phone has been severed. Literaraly the weirdest thing that has happened to me in a decade of Android phone ownership.
Googled all the black screen issues with these phones and most of them are resolved with just a soft reset... some said that the phone is in it's lowest dimmed state and go to a dark room and i'll see it faintly and then can increase brightness... no luck...
Has anyone experienced this?
I would say it's a warranty job, just tried turning my brightness to zero and you can still see the screen.
I did have a similar problem on an old note that had root and custom rom though but I had somehow set the volume rocker to control brightness and it had lowered itself to minimum in my pocket
KEVIN88GT said:
Non rooted, T mobile branded 3 month old note 8. No water damange, no drops etc.
Using chrome one miniute, set the phone down to watch a movie on my tablet, picked up the phone to check messages and boom. Screen is off. The phone works, I can even answer calls because I know where the answer button is on the screen, haptic feedback works, all indicator lights work. The phone screen remains off.
Tried a soft reset (tried hard reset too the best I could being I cant see the screen) and the phone seems to reset based on the vibration and indicator light patters but the screen remains off. It's as if a physical connection between the screen and the brains of the phone has been severed. Literaraly the weirdest thing that has happened to me in a decade of Android phone ownership.
Googled all the black screen issues with these phones and most of them are resolved with just a soft reset... some said that the phone is in it's lowest dimmed state and go to a dark room and i'll see it faintly and then can increase brightness... no luck...
Has anyone experienced this?
Click to expand...
Click to collapse
Try pressing and holding Volume down and power button for 5 to 7 seconds to force power off, then try to boot to download mode Volume Down + Bixby + Power button and see if the download mode screen shows......if not then probably a bad screen.
Sent from my God Mode 8
Tried it......nothing.....warranty job it is.... Bummed to have some refurnished phone in exchange for a Brand new 900 dollar phone just a few months back?
KEVIN88GT said:
Tried it......nothing.....warranty job it is.... Bummed to have some refurnished phone in exchange for a Brand new 900 dollar phone just a few months back?
Click to expand...
Click to collapse
Yeah that sucks, i can imagine..... i too hate the idea of refurbished units being swapped for warranty....bs, should be brand new unit!
Sent from my God Mode 8
so I had it replaced under warranty through T mobile. Refurb phone will come in today. One quesion. Should I let the Tmobile techs do the data/settings transfer from old phone to new one or just do everything myself from scratch (which will obviously take longer).
This happened to my phone twice for the past month or so. (both in Nougat and Oreo - Non rooted) Black screen but phone seems to be responding -- I can receive calls and notifications etc -- And force reboot doesn't fix it. I've also tried drainging the phone when it first happened to me but doesn't work. HOWEVER, it gets okay so randomly. Like I just left it for couple of hours and it just worked when I hit the power button.
I did tried bringing the device to Samsung but what they did is to just manually upgrade/reset the software in their end which I could have done in my part but I just let them do it. They told me to come back if it happens again which is kinda BS.
I can conveniently say this is a Hardware issue. I will wait for it to happen again on my phone and request for a replacement. Phone is 4 months old when it first happened.
I have the same issue with blank screen but phone is working.
It started couple of weeks after i dropped my phone on the ground. There is black dot on my screen and broken glass but phone was working ok and was still pretty usable. But then it started:
Display works fine but when i switch display of, lock the phone or display switched because of its timer it didn come switch on... But phone works, i can use it with blank (black) screen.
I had to do force restart so the display will turn on with samsung logo and booting screen, and keep on till another switch of.
I was trying every setting (but no hard reset) and then i found a little hack:
When you turn on the "Always On Display" (AOD) function you can let the screen switch off or do it manually, wait for 1-2 sec and always on display will come up to the screen. Then when you press home button or lock button screen will swtich on normally. YOu can type pin and use phone witch screen working. But when you try to unlock from "AOD" with your finger or your eyes it unlock but with screen black.
So i was using it like this. everytime you need to wait second untill AOD comes up, but it was working fine.
Problem nu 2 is that now it stop working, AOD is working but when i want to switch screen on from AOD it shows black screen and phone is working on blind.
So everytime after my screen goes black or to AOD i have to unlock the phone blindly and "Force restart" it and have to keep waiting until boot, and then have to never let phone to screen of.
Its not usuable.
¨
Now what do you think? Is it hardware problem or software problem? Because screen is working but randomly. The black dot of dead pixels on the screen is getting slightly bigger in time (about 1 year) but its like 1.5cm round. Maybe this cause the problem? And why hack with AOD was working for half a year and then stoped working? There wasnt any updates right before, but i tried to install some apps (non display related) so ill try to uninstall them.
Hawe you got any idea if i can repair it on my own even if i loose the waterproofability?
Or can it be replaced for free if i have a warranty? (I dont have insurance)
Thanks for your tips guys.
Reprocrastinator said:
I have the same issue with blank screen but phone is working.
It started couple of weeks after i dropped my phone on the ground. There is black dot on my screen and broken glass but phone was working ok and was still pretty usable. But then it started:
Display works fine but when i switch display of, lock the phone or display switched because of its timer it didn come switch on... But phone works, i can use it with blank (black) screen.
I had to do force restart so the display will turn on with samsung logo and booting screen, and keep on till another switch of.
I was trying every setting (but no hard reset) and then i found a little hack:
When you turn on the "Always On Display" (AOD) function you can let the screen switch off or do it manually, wait for 1-2 sec and always on display will come up to the screen. Then when you press home button or lock button screen will swtich on normally. YOu can type pin and use phone witch screen working. But when you try to unlock from "AOD" with your finger or your eyes it unlock but with screen black.
So i was using it like this. everytime you need to wait second untill AOD comes up, but it was working fine.
Problem nu 2 is that now it stop working, AOD is working but when i want to switch screen on from AOD it shows black screen and phone is working on blind.
So everytime after my screen goes black or to AOD i have to unlock the phone blindly and "Force restart" it and have to keep waiting until boot, and then have to never let phone to screen of.
Its not usuable.
¨
Now what do you think? Is it hardware problem or software problem? Because screen is working but randomly. The black dot of dead pixels on the screen is getting slightly bigger in time (about 1 year) but its like 1.5cm round. Maybe this cause the problem? And why hack with AOD was working for half a year and then stoped working? There wasnt any updates right before, but i tried to install some apps (non display related) so ill try to uninstall them.
Hawe you got any idea if i can repair it on my own even if i loose the waterproofability?
Or can it be replaced for free if i have a warranty? (I dont have insurance)
Thanks for your tips guys.
Click to expand...
Click to collapse
If you're under warranty it will likely be a free repair, unless they find other damage. Like moisture damage.
As far as fixing it yourself, it's just about as cheap to have Samsung do it than it is to buy the parts yourself. It's $229 for Samsung to do it, and you'll maintain the water resistance rating.
same has happened to me
KEVIN88GT said:
Non rooted, T mobile branded 3 month old note 8. No water damange, no drops etc.
Using chrome one miniute, set the phone down to watch a movie on my tablet, picked up the phone to check messages and boom. Screen is off. The phone works, I can even answer calls because I know where the answer button is on the screen, haptic feedback works, all indicator lights work. The phone screen remains off.
Tried a soft reset (tried hard reset too the best I could being I cant see the screen) and the phone seems to reset based on the vibration and indicator light patters but the screen remains off. It's as if a physical connection between the screen and the brains of the phone has been severed. Literaraly the weirdest thing that has happened to me in a decade of Android phone ownership.
Googled all the black screen issues with these phones and most of them are resolved with just a soft reset... some said that the phone is in it's lowest dimmed state and go to a dark room and i'll see it faintly and then can increase brightness... no luck...
Has anyone experienced this?
Click to expand...
Click to collapse
This has just happened to my note 8 too. I was about to update it and had started it. set my phone down and picked it up and phone screen is black but can hear the haptic feedback.
I can only see the lock screen and the notifications. Everytime I try to unlock my phone I only get to see a glimpse of the notescreen and then the screen turns black. Even when I try to go to camera through the lock screen the screen goes black too. When I charge my phone it heats up so I haven't really charged it as well. Has this also happened to anyone? It seems as if the phone's sensitivity still works in all places but when I unlock it the screen just goes black.
I also have problem of freezings and always rebooting. Tried soft and hard resets/factory reset. Still same problem. This phone has hardware issue. Do not buy.
I realize this thread is quite old but I have this exact same issue now. I have managed to discover some other information by playing around with various settings which are noted below. To begin with, I was able to used the AOD hack posted above for a while but it no longer works. The only way I can get my screen to come back is with a soft reset - but as soon as the screen times out or i turn it off, it goes black, with or without AOD enable. All the on screen buttons still work as well as the haptic feedback - I just can't see anything.
Now on to what I have found:
One thing I have found is if I turn off adaptive screen brightness and crank the brightness slider to the right, when it goes black I can faintly see some of the buttons - enough that I can turn the phone off or restart it from the power menu (If I switch the default setting to night that also helps to see the buttons a bit better). Also, if I enable night mode I can also see the brightness slider faintly but when I slide it left, it just makes the screen completely black and when I slide it right, it only returns it to the very faint brightness level.
So at this point I am stuck. To summarize the issue:
1. When the screen either times out or turns off, it is still "alive" but goes black. It will not return to normal brightness.
2. Turning off adaptive brightness and cranking brightness slider to right allows you to see faint buttons after screen times out but won't return to normal brightness.
3. Enabling night mode helps to see the faint buttons, in particular the brightness slider a bit better. However the screen still cannot return to normal brightness.
4. The only way to get the screen back to full brightness (albeit temporarily until the next timeout) is to turn off the phone or reset from the power menu; or soft reset holding volume down + power simultaneously.
Hopefully someone else has figured out a way to recover this. I am on Android 9 with Samsung UI 1.0
Phone is completely stock, never rooted and completely out of warranty.