Database Develop

[Resolved] Stuck in Download Mode after failed flash attempt.

Okay, so I finally decided to ditch AT&T and go full Paranoid (This is not my first flashing attempt with Android devices). Got the latest version, etc. Load into BootStrap and wipe everything. Go to install PA and for some reason I had neglected to tell my build.prop (ro.product.device/name) is supposed to be "jactivelteatt"/"jactivelteuc" and not "SN-M9009". So when I started the flash process, immediate error and now I'm stuck with a phone with no OS or bootloader and can not, for the life of me, find a ROM to flash with .MD5 or .TAR that will work with ODIN. I did find "Oneclick_I537UCUAMF1" that gets all the way to the end and fails. Tried multiple times with multiple cables.
Please if anyone has any idea's, please help.

timmytron said:
Okay, so I finally decided to ditch AT&T and go full Paranoid (This is not my first flashing attempt with Android devices). Got the latest version, etc. Load into BootStrap and wipe everything. Go to install PA and for some reason I had neglected to tell my build.prop (ro.product.device/name) is supposed to be "jactivelteatt"/"jactivelteuc" and not "SN-M9009". So when I started the flash process, immediate error and now I'm stuck with a phone with no OS or bootloader and can not, for the life of me, find a ROM to flash with .MD5 or .TAR that will work with ODIN. I did find "Oneclick_I537UCUAMF1" that gets all the way to the end and fails. Tried multiple times with multiple cables.
Please if anyone has any idea's, please help.
Click to expand...
Click to collapse
Oh god are you on the US version (SGH-I537)? If you're on the international version (I9295) ignore this post but otherwise, you need to read and take in my short rant. Trust me I wish this weren't the case, but it is, and it's important:
The Galaxy S4 Active i537 has a locked bootloader. There is no way around this, no ifs ands or buts. You simply cannot flash custom ROMs or recoveries. That's it, end of story as far as CM, CWM, AOSP and such things are concerned. That being said there is a sort of recovery called SafeStrap which you can use to make nandroid backups, flash mods and STOCK-BASED roms, but it's not a true custom recovery in the sense that we had been used to, because of this locked bootloader nightmare.
OK so I think you're gonna want to check out this thread. It's all about how to install any firmware from download mode, I think you're gonna have to go with NE3 or NH3.
Let me reiterate. NO CUSTOM ROMS. NO CWM. No Paranoid, no cyanogenmod, no AOSP, no crossing go before going directly to jail. Sorry for the stupid joke but seriously, you have got to keep your phone on stock-based roms (of which there are unfortunately few).
Firmware download links

timmytron said:
Okay, so I finally decided to ditch AT&T and go full Paranoid (This is not my first flashing attempt with Android devices). Got the latest version, etc. Load into BootStrap and wipe everything. Go to install PA and for some reason I had neglected to tell my build.prop (ro.product.device/name) is supposed to be "jactivelteatt"/"jactivelteuc" and not "SN-M9009". So when I started the flash process, immediate error and now I'm stuck with a phone with no OS or bootloader and can not, for the life of me, find a ROM to flash with .MD5 or .TAR that will work with ODIN. I did find "Oneclick_I537UCUAMF1" that gets all the way to the end and fails. Tried multiple times with multiple cables.
Please if anyone has any idea's, please help.
Click to expand...
Click to collapse
What phone do you have (i537 or i9295) and what version of firmware were you on?

Devo7v said:
What phone do you have (i537 or i9295) and what version of firmware were you on?
Click to expand...
Click to collapse
i537 and second to last, I537UCUCNE3

Okay, :laugh: I'm back. FINALLY found some MD5 files that loaded. In the process of updating and putting things back they way they were. Thank you to all who viewed/helped!
Is there a way to mark this as "Resolved"?

Web browser login, edit, advanced.
Add "solved" to title?

same problem with my i537, need help
timmytron said:
Okay, :laugh: I'm back. FINALLY found some MD5 files that loaded. In the process of updating and putting things back they way they were. Thank you to all who viewed/helped!
Is there a way to mark this as "Resolved"?
Click to expand...
Click to collapse
Need help, having the same problem

baddhabbitz88 said:
Need help, having the same problem
Click to expand...
Click to collapse
Have you used ODIN before?

i537 Stuck in download mode
timmytron said:
Have you used ODIN before?
Click to expand...
Click to collapse
yes I have use odin but I think I have the same issue you did, need to know where to get the files .

baddhabbitz88 said:
yes I have use odin but I think I have the same issue you did, need to know where to get the files .
Click to expand...
Click to collapse
Okay. Well I'm not sure where I got the files either. What I'm going to do is upload them (please do keep in mind that it's a huge file) to my Drive account and I will link it here when complete. You are on the AT&T i537 version?

baddhabbitz88 said:
yes I have use odin but I think I have the same issue you did, need to know where to get the files .
Click to expand...
Click to collapse
Did you get my PM?

timmytron said:
Okay. Well I'm not sure where I got the files either. What I'm going to do is upload them (please do keep in mind that it's a huge file) to my Drive account and I will link it here when complete. You are on the AT&T i537 version?
Click to expand...
Click to collapse
Yes, the at&t version i537 is the one I'm. Found some files this morning and run them in Odin but now back at bootloop. I'll check your files and see whats up on that end. It sucks because have not done anything to this phone unlike my other ones and this crap starts with this one on its own.

baddhabbitz88 said:
Yes, the at&t version i537 is the one I'm. Found some files this morning and run them in Odin but now back at bootloop. I'll check your files and see whats up on that end. It sucks because have not done anything to this phone unlike my other ones and this crap starts with this one on its own.
Click to expand...
Click to collapse
Well AT&T decided to completely lock us out on this particular version on this particular phone. At least we have *ROOT*.

baddhabbitz88 said:
Yes, the at&t version i537 is the one I'm. Found some files this morning and run them in Odin but now back at bootloop. I'll check your files and see whats up on that end. It sucks because have not done anything to this phone unlike my other ones and this crap starts with this one on its own.
Click to expand...
Click to collapse
You need to make sure you are flashing a version that is the same or more recent than the version you are currently on. You cannot downgrade your firmware or else you'll end up with a bootloop.

Devo7v said:
You need to make sure you are flashing a version that is the same or more recent than the version you are currently on. You cannot downgrade your firmware or else you'll end up with a bootloop.
Click to expand...
Click to collapse
k will try to find a more updated version but that is part of the problem is locating the firmware I need + this started doing it on its own and really never dug into it to no which firmware was on it other than rooted months ago with towelroot
---------- Post added at 09:36 PM ---------- Previous post was at 09:04 PM ----------
timmytron said:
Did you get my PM?
Click to expand...
Click to collapse
yeah I got it thanks but it didn't work still digging

baddhabbitz88 said:
k will try to find a more updated version but that is part of the problem is locating the firmware I need + this started doing it on its own and really never dug into it to no which firmware was on it other than rooted months ago with towelroot
---------- Post added at 09:36 PM ---------- Previous post was at 09:04 PM ----------
yeah I got it thanks but it didn't work still digging
Click to expand...
Click to collapse
Always check the stickies.
http://forum.xda-developers.com/showthread.php?t=2892445

Please help

Hi im having difficulty restoring my g900a back to stock. i think i found the stock firmware from zedomax and it works but im still having a problem. on his video he is extracting ONE file but when i download the att firmware there is 4 and im pretty sure i need all the fiels to be flashed. is there a way to do that? here is the file http://galaxys5root.com/galaxy-s5-stock-firmware/
when i unzip there is 4 tar files. i did the biggest one but i think im missing the bootloader, recovery ect. please help anyone ive tried different stock firmwares on xda and all of them just fail. thanks guys.

What method are you using to flash? Odin or safestrap? Do you have safestrap installed?

feelinfroggy23 said:
Hi im having difficulty restoring my g900a back to stock. i think i found the stock firmware from zedomax and it works but im still having a problem. on his video he is extracting ONE file but when i download the att firmware there is 4 and im pretty sure i need all the fiels to be flashed. is there a way to do that? here is the file http://galaxys5root.com/galaxy-s5-stock-firmware/
when i unzip there is 4 tar files. i did the biggest one but i think im missing the bootloader, recovery ect. please help anyone ive tried different stock firmwares on xda and all of them just fail. thanks guys.
Click to expand...
Click to collapse
It might be the actual stock ROM (I didn't check that particular file you mentioned) but in general the stock ROM for this phone comes in four files which begin with the following:
AP, CP, CSC, BL
You can load those in their corresponding spots in Odin (BL in bootloader, and so on)
Or you can head over to sammobile and download the stock firmware, which is a Samsung Kies dump file. This is one giant tar ball ( like the one in the video) which you'll just load into the PDA section of Odin 3.09 and flash away.

When you're clicking on ODIN are you running it as Admin? Also see the guy in the video using a USB 2 cable.

yes i am running as admin. it only works when i only use pda. when i put in the bl and csc and cp is keeps failing. after if flashed the pda file the phone reboots and freezes on the samsung screen. should i try doing it one by one?

it wont work still failing. should i flash one by one?

I did but i cant load it. i only get to the samesung logo and it freezes. only thing i can get into is download mode and the stock recovery. is there a way to boot into safestrap when phone is off? im running out of ideas and ive tried to do it on different computers and cords.

it seems like the bootloader file is the only one not working. do you have any idea? please please please help guys

feelinfroggy23 said:
it seems like the bootloader file is the only one not working. do you have any idea? please please please help guys
Click to expand...
Click to collapse
Don't flash the bootloader and you should be fine

I tried that and it still freezes on Samsung logo. Does anyone have a legit firemware I've tried the ones on here or does anyone know how to get the one from sammobile? Really appreciating the help
Sent from my RM-975_1005 using XDA Windows Phone 7 App

Download the G900A_Downgrade_to_NCE.tar from here:
https://www.androidfilehost.com/?fid=23622183712464416
Use Odin 3.09 and flash in AP slot. Once it is done then take the OTA for NG3 then OA1
Thanks to @muniz_ri
Sent from my SAMSUNG-SM-G900A

Waiting4MyAndroid said:
Download the G900A_Downgrade_to_NCE.tar from here:
https://www.androidfilehost.com/?fid=23622183712464416
Use Odin 3.09 and flash in AP slot. Once it is done then take the OTA for NG3 then OA1
Thanks to @muniz_ri
Sent from my SAMSUNG-SM-G900A
Click to expand...
Click to collapse
the download says thats for the gs4?

feelinfroggy23 said:
the download says thats for the gs4?
Click to expand...
Click to collapse
It is the right tar. I have used it many times to go back to stock after root.
Sent from my SAMSUNG-SM-G900A

Can you walk me through your process please?
Sent from my RM-975_1005 using XDA Windows Phone 7 App

feelinfroggy23 said:
I tried that and it still freezes on Samsung logo. Does anyone have a legit firemware I've tried the ones on here or does anyone know how to get the one from sammobile? Really appreciating the help
Sent from my RM-975_1005 using XDA Windows Phone 7 App
Click to expand...
Click to collapse
Use the G900A_DOwngrade_to_NCE.tar from this link http://forum.xda-developers.com/att-galaxy-s5/general/how-to-root-g900aucu2aoa1-4-4-4-2-3-2015-t3021120 and flash in the pda. that should fix your problem.

feelinfroggy23 said:
Can you walk me through your process please?
Sent from my RM-975_1005 using XDA Windows Phone 7 App
Click to expand...
Click to collapse
Download the G900A_Downgrade_to_NCE.rar. Unzip and you should get this file "G900A_Downgrade_to_NCE.tar.md5". Now Run Odin 3.09 as admin, and put your phone in download mode. In Odin click on the AP icon and point to the G900A_Downgrade_to_NCE.tar.md5. Wait until Odin finishes loading the file it takes some time. Plug usb cable to your phone while in download mode. Once Odin is ready click start. Wait until Odin is done. Your phone will reboot once the flash is done. Please Thank @muniz_ri for his hard work.

Yea. Prolly should have checked this forum before you went on the journey.
---------- Post added at 10:45 PM ---------- Previous post was at 09:56 PM ----------
Now, Instead of making sarcastic comments, I will provide some assistance. There is one thing left out of all of these tutes that took me a while to catch on to. As a result, my phone was doing the same thing.
When you follow the downgrade instructions, yes leave out the boot loader. Sometimes, the downgrade doesn't do the job properly, so you'll have to go to this thread, scroll to the very bottom post and you'll see a link for "G900A_NCE_Stock_Modem"
You will need to flash this along with the stock firmware. It should correct the boot issue. (Flash in PDA slot)
Furthermore, you will not be able to update via WiFi OTA. You'll have to download the official update files in .zip format.
Go to this thread for the " G900A_NCEtoNG3_OTA.zip" to update from NCE to NG3.
This next step is optional, but it won't hurt to try it. Go here and grab the stock NG3 modem and recovery. Flash each (one at a time) in the PDA slot.
My personal opinion of the 4.4.4 update is low. There are many issues with it. But if you're trying get the phone completely up to date then:
Go here for the final update.
You should now be set. Please thank @muniz_ri for his unrelenting dedication to helping others.
It is not my intention to be an ass, but you should begin with google, and then search entire AT&T forum before posting questions like this. Chances are, others have had the same problem, asked, and received a solution exactly like this.
Anyways, I hope I was able to guide you in the right direction...
Edit: It seems that both of the update zips are in the OA1 root guide thread.
P.S.
Your phone is from AT&T, right?

Note 4 SM-N910T that keeps getting stuck in a boot loop

So i purchased a Note 4 SM-N910T about a year ago. It worked fine but last month shortly after the 5.1.1 update I did it started randomly restarting for no reason. First i taught it was Snapchat because I red somewhere that there are camera problems, so I stopped using it. But it kept restarting even after that. From then I have made a factory and a master reset, rooted the phone and even installed CM 12. No mater what i do it keeps on restarting. The only way to get it out of the boot loop is to connect it to a charger that is not a fast charger. Then it starts charging and works normally and you can do everything normally. After you remove it from the charger it works as long as you do not use it. When you start using it and want to do something with it it starts restarting again. I hope somebody can help me fix this issue. I have noticed that connecting it to WIFI makes it 100% sure that it will restart any moment. If you leave it without WIFI as long as you do not do anything big it will not restart. For example I watched series on my phone I downloaded beforehand. I was able to go to the CM 12 file manager and change series for the duration of my bus drive and it has not reset yet and it has not been connected to a charger for around 12 hours already.
My last resort is to wait 3 hours for the stupid free 5.0.1 official firmware and flash it using the TWRP Recovery or Odin. If that does not work I would have t give it to a service. Any help will be greatly appreciated! Also a link to where I can download the 5.0.1 official firmware for free in normal speed will be of greatly appreciated as well!
Merry Christmas!

That's odd, I recommend odin flashing the stock ROM and everything. (Modem + bootloader) the latest one is DOK2 for T-Mobile

MisterCoolBeans said:
That's odd, I recommend odin flashing the stock ROM and everything. (Modem + bootloader) the latest one is DOK2 for T-Mobile
Click to expand...
Click to collapse
Do you have a link to where I could download that because all I found were sites where the free user speeds took 3 hours to download 1.5 GB?:crying:

Let me see if I can find one
---------- Post added at 04:41 PM ---------- Previous post was at 04:40 PM ----------
Here is the full untouched ROM that you can download from Sammobile but it was uploaded to mega instead.
http://forum.xda-developers.com/note-4-tmobile/development/mirror-stock-tw-t3260858
Make sure you click the first link!

MisterCoolBeans said:
Let me see if I can find one
---------- Post added at 04:41 PM ---------- Previous post was at 04:40 PM ----------
Here is the full untouched ROM that you can download from Sammobile but it was uploaded to mega instead.
http://forum.xda-developers.com/note-4-tmobile/development/mirror-stock-tw-t3260858
Make sure you click the first link!
Click to expand...
Click to collapse
Thank you very much! I put it for download and it has a reasonable speed. After its done I will try and flash it! I hope the problem does not occur anymore!

Lazarov987 said:
Thank you very much! I put it for download and it has a reasonable speed. After its done I will try and flash it! I hope the problem does not occur anymore!
Click to expand...
Click to collapse
So since the phone restarts when I connect it to the WIFI should i also flash the stock modem or just try first without it?

Lazarov987 said:
So since the phone restarts when I connect it to the WIFI should i also flash the stock modem or just try first without it?
Click to expand...
Click to collapse
If you flash the stock firmware it includes the baseband and modem

ShrekOpher said:
If you flash the stock firmware it includes the baseband and modem
Click to expand...
Click to collapse
To revive the thread I tried flashing the N910TUVU2DOK2_N910TTMB2DOK2_N910TUVU2DOK2_HOME.tar via Odin. It all went fine and after starting the phone it went on to the step where its optimizing apps. It got stuck there and it went back to the boot loop. I had reflash the CM 12 and TWRP Recovery and now I am back at 0. So my question is how should I flash the stock rom. Go to TWRP do a factory reset than turn the phone off and flash the stock rom via Odin? Should I also flash TWRP ans SuperSu after flashing the stock rom?
Thank you for your help!

I've been having the same problem for about a week and a half; it's super annoying. I was running Dynamic Pop on COG2 then yesterday I updated to DOK2 and flashed Maximum Overdrive... no improvement. It rarely even fully boots before freezing or rebooting.
My best guess as to what the problem is that it may be overheating because it tends to actually boot if I put it in the freezer while booting, but then it freezes soon after taking it out. I suppose it could also be internal memory corruption.
Either way, I'm getting ready to do a warranty exchange.

Lazarov987 said:
To revive the thread I tried flashing the N910TUVU2DOK2_N910TTMB2DOK2_N910TUVU2DOK2_HOME.tar via Odin. It all went fine and after starting the phone it went on to the step where its optimizing apps. It got stuck there and it went back to the boot loop. I had reflash the CM 12 and TWRP Recovery and now I am back at 0. So my question is how should I flash the stock rom. Go to TWRP do a factory reset than turn the phone off and flash the stock rom via Odin? Should I also flash TWRP ans SuperSu after flashing the stock rom?
Thank you for your help!
Click to expand...
Click to collapse
First focus on getting a clean stock firmware booted. Do what you mentioned above but don't flash TWRP or superSu until the stock ROM is stable. We need to narrow down the issues so do as few modifications as possible.
---------- Post added at 06:02 AM ---------- Previous post was at 06:01 AM ----------
jazzmachine said:
I've been having the same problem for about a week and a half; it's super annoying. I was running Dynamic Pop on COG2 then yesterday I updated to DOK2 and flashed Maximum Overdrive... no improvement. It rarely even fully boots before freezing or rebooting.
My best guess as to what the problem is that it may be overheating because it tends to actually boot if I put it in the freezer while booting, but then it freezes soon after taking it out. I suppose it could also be internal memory corruption.
Either way, I'm getting ready to do a warranty exchange.
Click to expand...
Click to collapse
You may have messed up the partitions. There is a thread about the pit file you should check out.

ShrekOpher said:
First focus on getting a clean stock firmware booted. Do what you mentioned above but don't flash TWRP or superSu until the stock ROM is stable. We need to narrow down the issues so do as few modifications as possible.
---------- Post added at 06:02 AM ---------- Previous post was at 06:01 AM ----------
You may have messed up the partitions. There is a thread about the pit file you should check out.
Click to expand...
Click to collapse
What thread is that and how do I find it? I mean I always checked that in Odin i never had Re-partition on.

ShrekOpher said:
First focus on getting a clean stock firmware booted. Do what you mentioned above but don't flash TWRP or superSu until the stock ROM is stable. We need to narrow down the issues so do as few modifications as possible.
---------- Post added at 06:02 AM ---------- Previous post was at 06:01 AM ----------
You may have messed up the partitions. There is a thread about the pit file you should check out.
Click to expand...
Click to collapse
I actually downloaded 2 stock roms for my Note 4. One was the COG2 and the other one was the completely stock firmware. I tried flashing them but Odin failed (Auth) whatever that means. The only stock rom I was able to flash was 5.1.1 but it wouldn't boot up so I had to install CM 12 again! I have no idea how to fix the phone. All I want is to return to 5.0.1 and delete any changes. The phone has no apps on it so i have nothing to loose but I do not know how to do it..

Lazarov987 said:
I actually downloaded 2 stock roms for my Note 4. One was the COG2 and the other one was the completely stock firmware. I tried flashing them but Odin failed (Auth) whatever that means. The only stock rom I was able to flash was 5.1.1 but it wouldn't boot up so I had to install CM 12 again! I have no idea how to fix the phone. All I want is to return to 5.0.1 and delete any changes. The phone has no apps on it so i have nothing to loose but I do not know how to do it..
Click to expand...
Click to collapse
You cannot use 5.0.1 ROMs on DOK2 they will never boot and no down grading. You have to use 5.1.1 ROMs for now on.

ShrekOpher said:
You cannot use 5.0.1 ROMs on DOK2 they will never boot and no down grading. You have to use 5.1.1 ROMs for now on.
Click to expand...
Click to collapse
check this out
http://forum.xda-developers.com/not...-solution-to-emmcread-write-problems-t3281179

Ashwin Prabhunerurkar said:
check this out
http://forum.xda-developers.com/not...-solution-to-emmcread-write-problems-t3281179
Click to expand...
Click to collapse
This is exactly what is happening to my T-Mobile Note 4 (SM-N910T) and the thing that you did to your Canadian Note 4 is exactly what I want to do. But can I use the firmware you provided at: http://forum.xda-developers.com/note-4/general/ref-stock-firmware-kernel-modem-recovery-t2920452
or must I use the T-Mobile ones and if I have to use the N910T firmware where can I get it so I can do what you did? A link or a thread would be amazing cause I really miss using my phone as normal!

Lazarov987 said:
This is exactly what is happening to my T-Mobile Note 4 (SM-N910T) and the thing that you did to your Canadian Note 4 is exactly what I want to do. But can I use the firmware you provided at: http://forum.xda-developers.com/note-4/general/ref-stock-firmware-kernel-modem-recovery-t2920452
or must I use the T-Mobile ones and if I have to use the N910T firmware where can I get it so I can do what you did? A link or a thread would be amazing cause I really miss using my phone as normal!
Click to expand...
Click to collapse
Don't flash Canadian tar files
We are searching for the answer
Hope to come back to you with a solution

Try Odin flash back to stock.
@dannygoround

dannygoround said:
Try Odin flash back to stock.
@dannygoround
Click to expand...
Click to collapse
Doesnt work. Wont flash the stock rom. It says Fail(Auth)

Epg2 firmware

Anybody get it yet? Supposedly went official yesterday. About 300MB.
I unlocked your mum's bootloader.

It just arrived, and it was about 300MB. IT rebooted into TWRP, which just sat there. I rebooted, and then Andorid complained that the update didn't work. Well, duh!
That said, now I would like to know what I should have done or should do in the future. Any thoughts?

Mine just arrived
What's new?

Just found a story about it here - it is indeed the July update:
http://www.tmonews.com/2016/08/t-mobile-galaxy-note-4-note-edge-july-security-update/
Links in that article will eventually point you to here, where the update can be downloaded manually and installed via Samsung Smart Switch.
https://support.t-mobile.com/docs/DOC-16486#update_download
Since I am rooted I am actually not sure what to do, and would appreciate some advice.

300 mb is a big update. If you are rooted you will need to flash the new firmware in Odin. But you may want to hold off. I am note sure it adds any new features and will probably make your device incompatible with any ROMs that are currently available.

ShrekOpher said:
300 mb is a big update. If you are rooted you will need to flash the new firmware in Odin. But you may want to hold off. I am note sure it adds any new features and will probably make your device incompatible with any ROMs that are currently available.
Click to expand...
Click to collapse
Thanks - sound advice.
So, where should I be looking on my Note 4 for the 300 MB download that happened earlier this morning, so I can delete it or copy/move it off for later?

I just got it but waiting to see if there are any bugs or negative effects. I'm not rooted so there's no way to go back.
Sent from my SM-N910T3 using Tapatalk

Still looking and haven't found any clues for changelog, not even security update. Anybody?
I unlocked your mum's bootloader.

Yep...trying to figure out how to avoid the update too.
I'm stick rooted with XPosed, Beastmode kernel, and a few other mods.

I just did the update, and I can confirm that TWRP, root, and xposed all work.
I don't know about compatibility with custom roms though.

ninjanick999 said:
I just did the update, and I can confirm that TWRP, root, and xposed all work.
I don't know about compatibility with custom toms though.
Click to expand...
Click to collapse
OK, so how did you install it?
To shut the System Update tool up, I had to freeze it in Titanium Backup.

wernst said:
OK, so how did you install it?
To shut the System Update tool up, I had to freeze it in Titanium Backup.
Click to expand...
Click to collapse
You can flash it with odin. The file is the all in one home odin file The file is floading around somewhere....Might look in Overdrives OP That might be where i saw it...

KennyLG123 said:
You can flash it with odin. The file is the all in one home odin file The file is floading around somewhere....Might look in Overdrives OP That might be where i saw it...
Click to expand...
Click to collapse
Yeah, if you can't find the update. You can just install the latest firmware you can find with odin, then update from settings.

Hi Folks,
I have no idea what "update from settings" means. Also, no idea where to start looking for the update - heck, I don't even know what to Google to find it. Thoughts?

wernst said:
Hi Folks,
I have no idea what "update from settings" means. Also, no idea where to start looking for the update - heck, I don't even know what to Google to find it. Thoughts?
Click to expand...
Click to collapse
From your device click settings look for about device click then at the top you will see (download updates manually) If you are rooted or removed any system apps dont go that route, the update will fail.. You then would just need the update file to flash with odin.. Might look in overdrives op.

What is overdrives op?

wernst said:
What is overdrives op?
Click to expand...
Click to collapse
http://forum.xda-developers.com/not...-maximum-ovrdrive-6-0-1-mm-beta-4-13-t3358326 Here.. you will see the link it a all in one (home) odin file just flash in ap or pda slot depending on which odin you use..

I believe this is the AFH Linky for the new firmware also fwiw: https://www.androidfilehost.com/?fid=24588212152306227

So just to be clear, Overdrive is a MM-based T-Mobile ROM, basically just debloated and with some minor tweaks.
As a convenience, he has linked to "N910T Stock Odin Full EPG2 Firmware File," which we can flash using TWRP onto an otherwise stock+rooted MM 6.0.1.
I got this right?

wernst said:
So just to be clear, Overdrive is a MM-based T-Mobile ROM, basically just debloated and with some minor tweaks.
As a convenience, he has linked to "N910T Stock Odin Full EPG2 Firmware File," which we can flash using TWRP onto an otherwise stock+rooted MM 6.0.1.
I got this right?
Click to expand...
Click to collapse
The PG2 file he has a link to is stock. That thread is for his pe3 custom though. I haven't made my rounds through note 4 thread yet. I maintain another android site and all the devices in my sig are active. I'm never on the same thread everyday....lol
---------- Post added at 02:35 PM ---------- Previous post was at 02:31 PM ----------
glensta said:
I believe this is the AFH Linky for the new firmware also fwiw: https://www.androidfilehost.com/?fid=24588212152306227
Click to expand...
Click to collapse
I'm starting to see more links pop up now. Thanks I 'm not even going to try this one out i'm staying on pe3 for awhile...

FW-8.0.0] S7 EDGE SNAPDRAGON - UNIVERSAL OREO G935UUES4CRG3 July 1/2018 sec

I Downloaded The Fw From Sammobile, Yes Its Was Very Slow, Thats Why I Re-upped It Untouched To Androidfilehost, Much Faster To Dl For Others.
Only For Snapdragon Variants, Its The Universal Firmware, Its Free Of Carrier Bloat But Has Some Samsung Useless Apps.
Not For Exynos Variants Like The Sm-g935f, Etc.
MORE ABOUT UNIVERSAL FW READ THIS
The Zip Has The Att Extension But All Universal Snapdragon Fw Are The Same Afaik, It Does Not Install Anything Specific For Att,
Im On Telus/koodo Using The Sm-g935a Without Issues, Shows Lte Signal When On Data Mode.
Idk If Auto Updates Work, Although Update Options Are Available From The System Menu
Instructions:
Dl Zip, Extract Zip, Put Phone In Dl/odin Mode. Run Odin As Admin, And Load Each Cp, Ap, Bl And Csc(Dont Use The Home Csc As I Read Its Fracks Things Up), Just Use "Csc_oym" File In Odin
Fyi. I Used Princes Odin But Failed, Used Untouched Odin And It Flashed Successfully. Was On Nougat 7.0 Sim Unlocked SM-G935A At&t Branded Stock Fw. I Included Both For Your Pleasure.
Afaik It Will Wipe Your Phone, Do A Backup As Needed
make a backup by using adb, search for this method, and a twrp nandroid
always make a backup, and never just one, and save them somewhere safe in multiple locations and clouds, hard drives die all the time
Disclaimer, Im Not Responsible For What You Do To Your Phones
G935UUES4CRG3_G935UOYM4CRG3_ATT.zip - 2.9GB
Odin3_v3.13.1.zip
Odin3+v3.12+(PrinceComsy).zip - not working with this fw

does wifi calling work this way or no bc its the unlocked version primarily?

Hi , can you confirm if this has no issue? im planning to flash my rom into oreo as well. thanks for sharing this.

Misslys9 said:
does wifi calling work this way or no bc its the unlocked version primarily?
Click to expand...
Click to collapse
rhayann77 said:
Hi , can you confirm if this has no issue? im planning to flash my rom into oreo as well. thanks for sharing this.
Click to expand...
Click to collapse
most answers to questions are linked in the op
MORE ABOUT UNIVERSAL FW READ THIS

vincom said:
answers, if any, are linked in the op
MORE ABOUT UNIVERSAL FW READ THIS
Click to expand...
Click to collapse
Hi Vincom, yes i have already read the article. the main reason im flashing the rom is because of the hidden DATA icon in the toggle screen. and also i want my phone to have the OREO update as well. this is my first samsung phone. i have experience in flashing ROMs in my xiaomi redmi 1s phone. so im a bit skeptical if i can do this on my own. this odin process is very new to me. so what is the worst thing that can happen it i brick my phone? can i do a hard reset and will it default to the stock AT&T ROM if ever?

rhayann77 said:
Hi Vincom, yes i have already read the article. the main reason im flashing the rom is because of the hidden DATA icon in the toggle screen. and also i want my phone to have the OREO update as well. this is my first samsung phone. i have experience in flashing ROMs in my xiaomi redmi 1s phone. so im a bit skeptical if i can do this on my own. this odin process is very new to me. so what is the worst thing that can happen it i brick my phone? can i do a hard reset and will it default to the stock AT&T ROM if ever?
Click to expand...
Click to collapse
odin is as easy as it gets, its made for samsung phones.
safe is to do nothing if ur happy as is.
NEVER EVER USE THE "PIT" OPTION UNLESS DIRECTIONS SAY SO IN XDA FORUM ONLY
read/watch vids on using odin
make a backup by using adb, search for this method, and a twrp nandroid
always make a backup, and never just one, and save them somewhere safe in multiple locations and clouds, hard drives die all the time

vincom said:
odin is as easy as it gets, its made for samsung phones.
safe is to do nothing if ur happy as is.
read/watch vids on using odin
make a backup by using adb, search for this method, and a twrp nandroid
always make a backup, and never just one, and save them somewhere safe in multiple locations and clouds, hard drives die all the time
Click to expand...
Click to collapse
Thanks again, ill watch some youtube videos first and if i feel confident enough then i will go thru with this. will keep you posted.
---------- Post added at 09:58 AM ---------- Previous post was at 09:36 AM ----------
rhayann77 said:
Thanks again, ill watch some youtube videos first and if i feel confident enough then i will go thru with this. will keep you posted.
Click to expand...
Click to collapse
Vincom, by the way this Oreo update has nothing to do with my CSC right? i just check its G935AATT4BQK2. my device model is SM-935A

rhayann77 said:
Vincom, by the way this Oreo update has nothing to do with my CSC right? i just check its G935AATT4BQK2. my device model is SM-935A
Click to expand...
Click to collapse
yes and no, csc controls what bloatware and which settings are setup by default dependant on carrier and country, hence why this is a universal fw and not dependant on original csc files.
if u truly have the att s7edge g935a, which is what i had, then yes.

vincom said:
yes and no, csc controls what bloatware and which settings are setup by default dependant on carrier and country, hence why this is a universal fw and not dependant on original csc files.
if u truly have the att s7edge g935a, which is what i had, then yes.
Click to expand...
Click to collapse
Thanks for the clarification. the download path keeps on failing on me for some reason. i already downloaded 1.8G or maybe its my internet speed perhaps?

rhayann77 said:
Thanks for the clarification. the download path keeps on failing on me for some reason. i already downloaded 1.8G or maybe its my internet speed perhaps?
Click to expand...
Click to collapse
could be android file host is having issues today
or u can try ur luck with sammobile.com which is where i initially got the file
edit. ya, i just tried, issues on their end

vincom said:
could be android file host is having issues today
or u can try ur luck with sammobile.com which is where i initially got the file
edit. ya, i just tried, issues on their end
Click to expand...
Click to collapse
i finally finished downloading the zip file earlier. i will flash it later after i go home from work. and one other thing i need to make sure. with this Oreo rom, the DATA connection icon will be available in the toggle screen right?

@vincom, this Oreo rom has already the DATA icon to be toggled on/off right? this is one of the reason i want to flash the att rom as well.

vincom said:
most answers to questions are linked in the op
MORE ABOUT UNIVERSAL FW READ THIS
Click to expand...
Click to collapse
I did read all of it but your description was vague on the att part so I didnt know if you modified it which it sounds like its just the 935u firmware and Im not a newb n00b

@vincom, initially got an error sha256 when i started to flash it. and my phone started to boot loop after i use a different odin, the prince odin. but after some searching. i fount out i just need to use the newer patch version of odin - Odin3 v3.13.1_3B_PatcheD and now im running Oreo on my s7 edge. hopefully this can help others too.

rhayann77 said:
@vincom, initially got an error sha256 when i started to flash it. and my phone started to boot loop after i use a different odin, the prince odin. but after some searching. i fount out i just need to use the newer patch version of odin - Odin3 v3.13.1_3B_PatcheD and now im running Oreo on my s7 edge. hopefully this can help others too.
Click to expand...
Click to collapse
did u try the one i have in the op, Odin3_v3.13.1.zip

vincom said:
did u try the one i have in the op, Odin3_v3.13.1.zip
Click to expand...
Click to collapse
yup i tried that one the first time. thats when it gave me the error message sha256. then i tried the prince odin that gave me the error mmc something.

The author claims performance and battery improvements but has anyone that switched over really noticed that big of a improvement?
I mean i already disabled all the carrier bloat with adhell isn't that basically the same as installing this rom? Does the universal maybe have a different kernal/different system level tweaks?

Bro , what will happen if my unlocked at&t s7edge installing this ? Is there sim will be locked again or not ? Thanks in advance and sorry for my bad english...

Rifuki18 said:
Bro , what will happen if my unlocked at&t s7edge installing this ? Is there sim will be locked again or not ? Thanks in advance and sorry for my bad english...
Click to expand...
Click to collapse
will not change your current sim lock status, no fw exists that would change it

Thanks
Thanks a lot, this firmware works for me with the 3b patched odin on the first try.