Note 5 (SM-N920C) Odin failed !! - Galaxy Note5 Q&A, Help & Troubleshooting

Hi there.
My galaxy note 5 (unlocked) was working very well until yesterday
Some apps start crashing and start to slow down
And after it suddenly restarted and stuck in a restart boot
I tried a lot of ways to fix it began of:
- Boot it in safe mode (the apps still crashing)
- Wipe the cache partition
- Wide data factory
- And after that i treid to install stock firmware with odin i followed all the instruction. But Odin still showing FAILED
and this message :
-----------------------------------------------------------
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> cm.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
---------------------------------------------------------------------
I activated the USB debugging and OEM unlocking btw.
Your help will be highly a appreciated
And thanks

Related

Samsung SM-G870A ATT Stuck in Downloading Mode - need help please

Issues began when I installed Lollipop on rooted phone. When flashing a custom rom it will not boot up. I cannot get to a recovery screen but can put it in download mode (Odin). I have downloaded the stock ATT rom and attempted to flash with odin but it fails everytime. I get the following on the screen.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
I have updated the samsung drivers and do not know where to go from here. any help is appreciated.
Gdogius

Need help to Unbrick my Tab S2 T710

After a failed root attempt, the screen would randomly go black and unresponsive. So, i decided to flash CM12 using TWRP. However, I accidently wiped the entire storage without backups and now it's stuck on bootup (Samsung Tab S2 powered by Android) and refuse to shutdown nor go to recovery. I tried using Odin to flash a stock ROM -T710XAR1BOH7- but Odin failed and the tablet shows -SW REV. CHECK FAIL. DEVICE: 2, Binary 1-
I got this from Odin.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T710XXU1BOH7_T710XAR1BOH7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas?
I ran into the same issue about a month ago, but I was able to restore using Samsung Smart Switch's restore function. Just download and run it with your tablet in download mode.
Xiang0428 said:
After a failed root attempt, the screen would randomly go black and unresponsive. So, i decided to flash CM12 using TWRP. However, I accidently wiped the entire storage without backups and now it's stuck on bootup (Samsung Tab S2 powered by Android) and refuse to shutdown nor go to recovery. I tried using Odin to flash a stock ROM -T710XAR1BOH7- but Odin failed and the tablet shows -SW REV. CHECK FAIL. DEVICE: 2, Binary 1-
I got this from Odin.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T710XXU1BOH7_T710XAR1BOH7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas?
Click to expand...
Click to collapse
You're trying to flash a revision 1 firmware on a revision 2 device.
ashyx said:
You're trying to flash a revision 1 firmware on a revision 2 device.
Click to expand...
Click to collapse
I flashed the newest build and that did the trick. (BPB1) Thanks.

Help can't flash anything to TMobile Note 5

I'm trying to go back to stock and i've tried every which way. When I try to do it through Odin it fails. I've tried on every USB port I have.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Then I tried through Smart Switch and it says its a Galaxy Edge 7 so it doesn't let me do the emergency restore.
Then I tried to flash any other room though TWRP and it just says failed and give Error 7.
Any help will be appreciated.
You need to download the correct firmware for your device

Attempting to flash stock firmware to unroot my Note 5 SM-N920T

I have a Note 5 SM-N920T and I had it rooted with Magisk. It was working great until I needed to remove the root. I tried to flash a stock firmware I found online and it failed giving me the error "sw rev. check fail. device 4 binary 2". I then forced my phone to reboot (power + vol down) and got back in download mode. I downloaded a newer version of the Note 5 firmware from Updato and flashed it. This time it passed in Odin but would never boot into android, instead, it would get stuck on the T-Mobile splash screen. Another weird thing I noticed is that the blue led will not shut off no matter what. Even when the phone is completely off and unplugged the led remains on. I need to get back to the original ROM/firmware but I can't do it. All help would be greatly appreciated as I have been unable to find anything so far after countless hours of scouring the internet. Until this issue is resolved I am without a phone so as mentioned above any and all help is greatly appreciated.
Odin Log when the error occurs:
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1101)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!

Rooting galexy S5 AT&T

is [this](https://forum.xda-developers.com/t/guide-root-roms-and-other-cool-stuff.3516196/) the most current method.
And I realize current is going to be old, as its an old device.
I have a G900A, I got an unlock code from AT&T and entered it. I don't have an active sim in the device (wifi only), and I'm trying to root, both kingroot/towelroot say something about make sure you have internet. Internet works fine I googled random things to verify.
Trying the guide above I can't get passed the first step of flashing the tar.md5 with the error below, anyone have any advice or guidance?
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbll.mbn
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
For anyone that finds themselves here, I solved my issue, by booting to recovery mode (vol up + home + power), then selecting to go to bootloader, it was the same screen as vol down, but it worked from that screen .

Categories

Resources