So I got my Xperia Z like a week ago and just bought the Roxfit bumber with scratch resistant protectors.
The shatterproof protector already has quite a lot of scratches in front and rear.
I was wondering if its better to remove the shatterproof protector and apply the scratch resistant ones?
Also if I apply them on top of the shatterproof protector, is it possible to cover/fix the scratches that are visible on the screen?
I applied a scratch resistant protector on top of the shatter proof one, because the pre applied shatter proofing layer is very prone to scratches. Then I have a soft touch slim case all over it. No problems.
Hey there. Just wondering if anyone using Tempered glass screen protector and Defender case? any fitment issues?
thanx
I did have an issue with with Nilkin Tempered glass + defender, but i am quite certain that was because of the adhesive left behind after removing their inbuilt screen protector.
So in short, any 0.3mm thickness tempered glass will do as long as you properly remove the adhesive that's left behind after removing their built in screen protecter.
thanx
Wondering if anyone knows of a rear glass plastic film protector. I prefer no case, but the slipperiness and the fingerprint magnet that is the back glass has me wanting a back film but still clear to keep the design. I notice the front glass has an exceptional oleophobic coating to resist fingerprints, but I was hoping for something that was clear and a little more grippy, but not like a skin where it covers the back design.
Not available since the large curve... Your best bet is a skin or a film protector
Sent from my SM-N920T using Tapatalk
I have bough one of these
http://m.ebay.de/itm/111780429237
Please consider using a clear decal from SKINOMI.
Also Dbrand and Slickwraps have great designer decals.
Samsung told me the back is NOT gorilla glass.
So. I have a tempered glass screen protector on my phone right now that is not full coverage. I was thinking about buying some Kristall liquid screen protector to cover the edges that are not covered by my tempered glass protector. Thoughts from everybody? Do you think the liquid screen protector will bond with the tempered glass right?
I now have a dot matrix glass screen protector fits well sensitivity is good.
However it's highly reflective and shows every finger print yes it's easy to clean. But it's Really taking the enjoyment out of this phone.. I've tried film and plastic all have pros and cons..
I would luv to take it off but I live near a beach and I understand 1 grain of sand could ruin the screen... Any suggestions would be appreciated thanks
I think you will find it's all down to the quality of the protector, and the amount of TLC you give it. Many of the cheap protectors have little or no oleophobic coating, with the more premium protectors having the customary "slick" feel to them. This can be protected/topped-up by using various polishes and cleaners that are available.
Be careful about sand and dust getting under your for matrix tempered glass screen protector (TGSP). I bought my Note 8 used, and the previous owner had a TGSP on it since day one. Dust had began to leak in, including a piece of dust in the very center. When I took that TGSP off to install a wet install soft screen protector, I noticed that piece of dust in the middle had actually etched a spot into the glass on the screen. It's very small, and not really noticeable, but it's there. And it was caused by the one thing that was supposed to protect my screen.
whitestone is awesome, slick and doesnt leave fingerprints unless sweaty or greasy hands
My whitestone has a pretty good coating to prevent smudges and fingerprints. I have other qualms about it like bubbling and whatnot, but the coating and smoothness is better than the other tempered glass protectors I've used.
Using nilkin 3d cp+ tempered glass. Its been a month and bo glue issues.. Perfect sensitvity..and also it has very nice oleophobic coating..finaly a erfect glass protector...
---------- Post added at 02:22 AM ---------- Previous post was at 02:19 AM ----------
Nilkin cp max is also prrfectly compatible with my spigen thinfit..case
This is what I'm currently using and I love it. Full adhesive and oleophobic. Fits perfectly with a Ringke Air case.
Mr. Orange 645 said:
This is what I'm currently using and I love it. Full adhesive and oleophobic. Fits perfectly with a Ringke Air case.
Click to expand...
Click to collapse
Sorry bro which protector are you using?
Enviado desde mi SM-N950F mediante Tapatalk
fedez said:
Sorry bro which protector are you using?
Enviado desde mi SM-N950F mediante Tapatalk
Click to expand...
Click to collapse
Sorry, I could have sworn I put a link in my post. LOL
Galaxy Note 8 Screen Protector, Singularity Products Galaxy Note 8 Full AB Glue Tempered Glass Screen Protector Easy Installation Tray [Case Friendly] 3D Curved Glass Protector Film for Galaxy Note8 https://www.amazon.com/dp/B077GSJ55T/ref=cm_sw_r_cp_apa_3bbrAbD22EFEG
Eventually the oleophobic coating wears off the screen protector it will start attracting fingerprints like a magnet.
Yes ice, all oleopfobic coatings, including the one on the screen itself wears off with time, no matter what
I am using Nano Optics Tempered Glass Screen Guard with UV Light, Glue.
It is way better. 3D bend at edges and good touch sensitivity.
Good oleophophic coating.
U can try this
https://www.amazon.in/dp/B07KWCGWH6...olid=216AT1UAAULJI&psc=0&ref_=lv_ov_lig_dp_it
White stone dome glass is a good solution !