Database Develop

Nexus S and ICS a little problem

Hi all
I did not receive the OTA so I decided to manually update my nexus s (I9020XXK1)
Unfortunately the navigation works only on wi-fi. Although the data navigation is turned on the mobile does not download email etc.
I thought it was a problem with widgetsoid and I disinstalled it but the problem is still there.
I also tried to update the APN via "APN Italiani" but the programs shows the generic message that "he encountered an error"
My question: do you have any idea how to work it out? and also: is there a program similar to widgetsoid for a dummy (me)?
thanks a lot

paperaino said:
Hi all
I did not receive the OTA so I decided to manually update my nexus s (I9020XXK1)
Unfortunately the navigation works only on wi-fi. Although the data navigation is turned on the mobile does not download email etc.
I thought it was a problem with widgetsoid and I disinstalled it but the problem is still there.
I also tried to update the APN via "APN Italiani" but the programs shows the generic message that "he encountered an error"
My question: do you have any idea how to work it out? and also: is there a program similar to widgetsoid for a dummy (me)?
thanks a lot
Click to expand...
Click to collapse
just flash a customer rom like aosp + (http://forum.xda-developers.com/showthread.php?t=1397358) -> all works

it would be even worst! I already tried but I'm a dummy and couldn't do it
at home I have a mac and could not get a propor procedure. now (at work) I have a pc but no administrator rights.
if there is an easy way to do it then I will give it a try but I would need a "guide for dummies"

paperaino said:
it would be even worst! I already tried but I'm a dummy and couldn't do it
at home I have a mac and could not get a propor procedure. now (at work) I have a pc but no administrator rights.
if there is an easy way to do it then I will give it a try but I would need a "guide for dummies"
Click to expand...
Click to collapse
go to market and install rom manager start it and install clockworkmod recovery (the first thing) download a customer rom and put it to your sd card bzw internal storage shutdown your phone then press vol down button start your phone now you are in clockworkmod recovery then wipe data factory reset then format cache and choose flash form zip choose your rom and flash it restart your phone thats it

try looking at this post
http://forum.xda-developers.com/showthread.php?t=878446
and this http://forum.xda-developers.com/showthread.php?t=1007782

Crespo_Fir3start3r said:
go to market and install rom manager start it and install clockworkmod recovery (the first thing) download a customer rom and put it to your sd card bzw internal storage shutdown your phone then press vol down button start your phone now you are in clockworkmod recovery then wipe data factory reset then format cache and choose flash form zip choose your rom and flash it restart your phone thats it
Click to expand...
Click to collapse
I downloaded "rom manager"
WhenI tried to install clockworkmode recovery he told me some problems occurred while executing provileged commands...

paperaino said:
I downloaded "rom manager"
WhenI tried to install clockworkmode recovery he told me some problems occurred while executing provileged commands...
Click to expand...
Click to collapse
fuu sri i forgot that you need root to install cmw
http://forum.xda-developers.com/showthread.php?t=1321582 download this and root your phone step by step with this one click tool very easy then follow the guide again

Crespo_Fir3start3r said:
fuu sri i forgot that you need root to install cmw
http://forum.xda-developers.com/showthread.php?t=1321582 download this and root your phone step by step with this one click tool very easy then follow the guide again
Click to expand...
Click to collapse
Ok I downloaded it and run the .bat file
checked everything and plugged the cable
clicked on "enter" the dos says:
*daemon not running. starting it now*
*daemon started successfully*
then?

paperaino said:
Ok I downloaded it and run the .bat file
checked everything and plugged the cable
clicked on "enter" the dos says:
*daemon not running. starting it now*
*daemon started successfully*
then?
Click to expand...
Click to collapse
click enter again and follow the guide in this tool erverything is explained

Crespo_Fir3start3r said:
click enter again and follow the guide in this tool erverything is explained
Click to expand...
Click to collapse
unfortunately "enter" brings noway
the dos prompt keeps there with no reaction..

paperaino said:
unfortunately "enter" brings noway
the dos prompt keeps there with no reaction..
Click to expand...
Click to collapse
that´s strange it should work :/
have you done all these things ?
[*] Before u begin:
(1) make sure u have installed adb drivers for ur device
(2) enable "USB DEBUGGING"
from (Menu\Settings\Applications\Development)
(3) enable "UNKNOWN SOURCES"
from (Menu\Settings\Applications)
(4) [OPTIONAL] increase screen timeout to 10 minutes
(5) connect USB cable to PHONE and then connect to PC
restart it maybe this help

Crespo_Fir3start3r said:
that´s strange it should work :/
Click to expand...
Click to collapse
the mobile is turned on. I have unplugged it, closed the prompt and re-launched the bat
now it only says:
---Starting
---Waiting for device

paperaino said:
the mobile is turned on. I have unplugged it, closed the prompt and re-launched the bat
now it only says:
---Starting
---Waiting for device
Click to expand...
Click to collapse
if you enabled usb debugging you have to connect your device with your pc

Crespo_Fir3start3r said:
that´s strange it should work :/
have you done all these things ?
[*] Before u begin:
(1) make sure u have installed adb drivers for ur device
(2) enable "USB DEBUGGING"
from (Menu\Settings\Applications\Development)
(3) enable "UNKNOWN SOURCES"
from (Menu\Settings\Applications)
(4) [OPTIONAL] increase screen timeout to 10 minutes
(5) connect USB cable to PHONE and then connect to PC
restart it maybe this help
Click to expand...
Click to collapse
(1) how do I install them?
(2) OK
(3) OK
(4) no it was optional...
(5) of course

paperaino said:
(1) how do I install them?
(2) OK
(3) OK
(4) no it was optional...
(5) of course
Click to expand...
Click to collapse
http://developer.android.com/sdk/win-usb.html a google tutorial how to install the drivers needed
beside I am at school so I am not able to answer everytime if I could I answer you sri for this

Crespo_Fir3start3r said:
http://developer.android.com/sdk/win-usb.html a google tutorial how to install the drivers needed
beside I am at school so I am not able to answer everytime if I could I answer you sri for this
Click to expand...
Click to collapse
I'm trying this way (hopefully it will work considering that I do not have administrator rights)
Would be great if there was a program to install directly on the nexus ...
beside I'm in the office
unfortunately it doesn't work
I don't have the provileges to update drivers on this pc. I will try later at home with my wife pc or something different

paperaino said:
I'm trying this way (hopefully it will work considering that I do not have administrator rights)
Would be great if there was a program to install directly on the nexus ...
beside I'm in the office
unfortunately it doesn't work
I don't have the provileges to update drivers on this pc. I will try later at home with my wife pc or something different
Click to expand...
Click to collapse
ohh ok xD and yes you need admin rights for this :/
Would be great if there was a program to install directly on the nexus ... ? do you mean the driver when yes they are for windows xD or what do you mean ?

Crespo_Fir3start3r said:
ohh ok xD and yes you need admin rights for this :/
Would be great if there was a program to install directly on the nexus ... ? do you mean the driver when yes they are for windows xD or what do you mean ?
Click to expand...
Click to collapse
we are trying all this just to root the nexus s (from my understanding)
would be great there was an easy way to get root access straight from the nexus without connecting it to a pc or mac

paperaino said:
we are trying all this just to root the nexus s (from my understanding)
would be great there was an easy way to get root access straight from the nexus without connecting it to a pc or mac
Click to expand...
Click to collapse
I do not know anything like that :S

Error: Kies does not support Mini 2

I'm receiving the below error when connecting my Mini 2 to my PC:
'This device is not supported by Kies 2.0.'
This is obviously not the case. I have tried to re-install Kies many times. Not a driver error as I can use it like an external drive in Windows Explorer.
mobile: Galaxy Mini 2 (S6500D), stock rom, usb debugging enabled (tried with disabled as well)
pc: Windows 8 Enterprise (does not need Media Feature Pack)
Kies: v2.5.2.13021_10
I have already checked tonns of forums but no solution found so far.
Thank you in advance for your ideas.

fishmong3r said:
I'm receiving the below error when connecting my Mini 2 to my PC:
'This device is not supported by Kies 2.0.'
This is obviously not the case. I have tried to re-install Kies many times. Not a driver error as I can use it like an external drive in Windows Explorer.
mobile: Galaxy Mini 2 (S6500D), stock rom, usb debugging enabled (tried with disabled as well)
pc: Windows 8 Enterprise (does not need Media Feature Pack)
Kies: v2.5.2.13021_10
I have already checked tonns of forums but no solution found so far.
Thank you in advance for your ideas.
Click to expand...
Click to collapse
Kies isn't supported in Windows 8 maybe ?

F4uzan said:
Kies isn't supported in Windows 8 maybe ?
Click to expand...
Click to collapse
It is.
Windows XP, Windows Vista, Windows 7, Windows 8**
** Windows 8 includes Windows Media Player.
If using Kies with Windows 8 operating systems, please be advised that currently only Samsung Android OS and BADA OS based mobile devices are supported
http://www.samsung.com/ca/support/usefulsoftware/KIES/JSP

Never used Kies before. Or it's because USB Cable ?

F4uzan said:
Never used Kies before. Or it's because USB Cable ?
Click to expand...
Click to collapse
Have you read the original post?
"Not a driver error as I can use it like an external drive in Windows Explorer."
Anyway I tried with Kies WiFi as well, but same error.

fishmong3r said:
Have you read the original post?
"Not a driver error as I can use it like an external drive in Windows Explorer."
Anyway I tried with Kies WiFi as well, but same error.
Click to expand...
Click to collapse
USB isn't the same like driver.... Try use different cable
Odesláno z mého GT-S5570 pomocí Tapatalk 2

david19au said:
USB isn't the same like driver.... Try use different cable
Click to expand...
Click to collapse
Tried. Same issue.

it's because CSC. i don't know a english post of how to solve this, but here i put a spanish tutorial translated:
Megatutorial: Change CSC (Country Specific Code)
Hello friends, I bring you good news, is on the CSC. It is very important because Megatutorial.
The first thing I have to say is, when the Stock Rom flashearon and went to Kies, noted that they came this message: "The device does not support software upgrade of Kies travez" I asked Samsung about it and they said it is a program error, but they were wrong.
Navigating today, I discovered that when you leave that message, you can never upgrade by Kies, but today, I found the solution. The just try, and I have regained the ability to upgrade by Kies.
What is CSC?
The CSC, for its acronym in English (Country Specific Code) refers to code each terminal, belongs to this region, to have one that does not correspond to our phone, it automatically stops inactualizable.
Navigating discovered how to change it, I'll put it in red to make it attractive.
procedure:
1. - First dial * # 272 * (not dial anything else, not pressed the call button)
2. - Following this put your IMEI (You can see it by dialing * # 06 #) and finally I put #
3. - I stay like this: * # 272 * 53259623505748 #
4. - Once done will get a menu with several CSC choosing whichever of Spain or location. You can search the Internet for the CSC. (Mine was PHE), this can also be seen when viewing the Stock ROM file includes code.
5. - They give the Install button, and the phone will restart, but when that happens, it automatically makes a Wipe will erase all applications.
NOTE: We agree that to flash the Stock Rom, starts in another language, then change it in-law, beginning in SPANISH. So if it works and check Kies, and I no longer went out that Messaging

1. - First dial * # 272 * (not dial anything else, not pressed the call button)
Click to expand...
Click to collapse
this code does not work on my device
i have S6500D
ROM:CM10(TheWhisp)

My mini 2 also doesn't work with kies, although my galaxy tab 2 7.0 works with it.

manu19thebest said:
...
Click to expand...
Click to collapse
Thank you, but unfortuantely it's not working my device.

[Q&A] [ROM] HUAWEI Ascend W1-U00 | v1.00

Q&A for [ROM] HUAWEI Ascend W1-U00 | v1.00
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer. Thanks for understanding and for helping to keep XDA neat and tidy! :smile:

DerSchorsch1 said:
It seems that in this video it's described, how the sdcard-problem can be permanently solved, so that we don't have to put the card out and in after a shutdown. Is this right?
Can this be implemented in the rom?
I don't understand the steps to do in the video. I can only recognize that i has something to do with visual studio. Can someone describe it more detailed?
---------- Post added at 07:25 PM ---------- Previous post was at 07:22 PM ----------
Everyone please donate, so he can buy a new gorilla glas display!
Click to expand...
Click to collapse
You did notice that this is an emulated device I hope? Rules for an emulator and for a live device are usually different.. just because a fix works in the emulator it doesn't have to work with the device.. and as far as I'm aware it doesn't.

Carrier Lock
Hi there,
Thanks for the ROM dev work!
I have a W1 which was O2 branded, after the procedure of installing the ROM, my phone has become carrier locked..
Is there an option I missed during install?
Regards,
Ed

I need help
Hello, I also use the HUAWEI Ascend W1 I come from China, I would like to know about the method of making the rom, and I open the app file will get a mbn file and do not know how to proceed, and I'm very interested in this, you can explain under it? (My English is not very good, but please forgive me use google) If you teach me, would be extremely grateful!

Hello,
thanks WojtasXda for the effort!
---------- Post added at 08:19 AM ---------- Previous post was at 08:13 AM ----------
It will be possible to install the rom from Osx or linux?

Registry tweaks from russian forum (4pda)
Here, guys, tweaks for our HUAWEI W1.
Go to \Windows\Packages\RegistryFiles and place OEMSettings.reg here.
First bootup will be ~2 minites.
Tweak list:
-Camera sound on/off in sound settings;
-Wi-Fi connection sound on/off;
-3g/Wi-Fi arrows in status bar switched on;
-Activated PfD (don't install program);
-Jailbreak(interop unlock,capabilities unlock)
-Can be installed hacked appx's from wp-seven
-SDK registered
-Search button opens google
-Any app can be placed to camera's button (e.g. OneShot)
-Now you have Nokia Lumia 920 (doesn't really work).
To make your phone 'NL920', you must mount in regedit 'SYSTEM' and install 2nd (zip). After that, you can easily install all Nokia Exclusives via SysApp Pusher (also, more apps in store!).

I think you've got a typo in the OEMSettings.reg file (inside the same-named archive), on one of the tweaks that's supposed to give file system via USB:
Code:
[HKEY_LOCAL_MACHINE\SYSTEM\controlset001\services\MtpSvn]
should be
Code:
[HKEY_LOCAL_MACHINE\SYSTEM\controlset001\services\MtpSvc]
unless it's supposed to control the Media Transfer Protocol Subversion

Will this work with Huawei Ascend W1-U00 from Globe PH plan?
Hi.
My phone was given to me by my mother who received it with her Globe (a Philippine mobile network service provider) postpaid plan (which unusually uses prepaid services). I've been frustrated with this phone's storage becoming full very easily even though I only have very few apps (except for Spider-Man Unlimited which downloaded a 200-MB DLC) installed and I don't put any files in the phone storage. Since Huawei seemingly abandoned their Windows phones, there's no hope of us getting any update so we're stuck with the stock WP8 update 1. Will this custom ROM work with this particular W1-U00? Does anyone know where I can get a stock ROM for this particular phone?
Name: Windows Phone
Model: HUAWEI W1-U00
Software: Windows Phone 8.0
Screen Resolution: 480x800
OS version: 8.0.10211.204
Firmware revision number: 1030.5614.29400.20500
Hardware revision number: HD1U8835M Ver.B
Chip SOC version: 8230

WojtasXda said:
Hello everyone !
I have new W1, but this is U34 version. Anyone tried flashign this model? Acctually QPST shows error "Cookie (if present) not received.
Click to expand...
Click to collapse
I have the U34 and I've not been able to flash it. I always get the same cookie error in QPST, and handshake failure error in WP8 Flash Tool.
I hope you will be able to find the way to flash the U34.

You need install Windows 7, Use Qemu or Vmware. Drivers from package with QPST doesnt works in W8.
Click to expand...
Click to collapse
That's not true at all. QPST works perfectly fine on Windows 8. The only issue is if you're running a x64 OS, in which case you need to run the QPST programs as admin.

Is this ROM only in English language?

Problems with Flashing
Hello!
At First thanks for the good work. I will donate it, if i getting it work for me.
I got some Problems with flashing.
1) With Flash Tool:
Diag Setting is on, Phone is resetted and with the Flashtool i get the "Firmware Handshake Fail"-Error.
2) With QPST i can get into Download Mode (Qualcomm ... 9008) but then it shows me a "Cookie not received"-Error.
I tried the Flashtool in Downloadmode but that doesnt recognize my device.
My PC-Config:
Windows 7 Ultimate 64-Bit
Intel i5 Notebook
My Handy-FW:
Huawei W1-U00 Simlock Free
OS Version: 8.10.14203.306 Developer Preview
Thank you very much!
Edit:
I got the Problem. It only works for me without Diag Settings and only with QPST.
The folder from the Repair Bootloader was: W1-U00 Repair bootloader/flashing/
and i only copied the "flashing" folder. Now no "Cookie"-Error.
Hope this helps someone....

Step 2 error
I finish step 1. Flash custom ROM with QPST (Windows 8.1 x64).
Phone in mass-storage mode (all disk available).
Qualcomm MMC Storage USB Device present in Device manager.
When run WP8CRUU get error: Cannot open device "Qualcomm MMC Storage USB Device" Error 5 .
Whats wrong?
Problem solved:
With phone connected as mass storage reinstall Qualcomm USB drivers!

Lag issue on the scroll
Hi @WojtasXda, I installed this wonderful ROM yesterday and everything is working perfectly THANK YOU SO MUCH <3
but when I scroll something with the finger always placed in the screen it lags a bit.
Huawei Ascend W1-U00
If you could help me to find a fix I thank

Error 109 on WP8CRUU.exe
Does v1.10 require v1.00 flashed first? I'm getting an error 109 (Cannot open device Qualcomm MMC Storage USB Device) when I run WP8CRUU.exe. My phone's (W1-U00) already in mass storage mode.
Now, I'm getting an error 5 (Cannot open device Qualcomm MMC Storage USB Device).
Can anyone please help me with this? I was able to flash the ROM with mass storage mode capability and set my phone to mass storage mode. Now, I can't flash the custom ROM because of this error. I don't think I missed anything. I'm running this on a Windows 7 Ultimate 64-bit. I didn't install MS Visual Studio 2013 since it requires Windows 8.1. I did install the Qualcomm USB drivers, simpleio, and QPST. I have MS Visual C++ 2005, 2008, and 2012 (all 32-bit) installed.
Arhy's workaround didn't work for me, by the way.

personal settings/data
Hi everybody,
is there a possibility to flash the rom and still keeping the wp8 personal settings (like contacts, certificates, calendar arrangements,...)
Or is it possible to do a "backup" of personal data in wp8 and do restore in wp8.1 ?
Any hints welcome.
BTW
Thanks for the rom and the hard work...

blonder_andi said:
Hi everybody,
is there a possibility to flash the rom and still keeping the wp8 personal settings (like contacts, certificates, calendar arrangements,...)
Or is it possible to do a "backup" of personal data in wp8 and do restore in wp8.1 ?
Any hints welcome.
BTW
Thanks for the rom and the hard work...
Click to expand...
Click to collapse
Try going to Settings -> backup.

tempname said:
Try going to Settings -> backup.
Click to expand...
Click to collapse
Thanks for the reply...
As far as is can see you just can backup fotos, messages, and IE-settings.
(no contacts, calender-information, certificates,...)
Is there another way to get at least my contacts from WP8 to WP8.1?
An additional question:
Is it possible to get back to WP8 after flashing the WP8.1 rom?
Any hints welcome
best regards
andi

install HUAWEI Ascend W1-U00 | v1.10
Hi, i try to install these rom.
To install that i do this steps:
1) Enter Qualcomm emergency mode
2) Click Start>All Application>QPST>QPST Configuration and configure phone
3) Start>All Application>QPST>eMMC Software Download，Click “Load Build Contents…” Select contents.xml in unrared W1-U00(C00)Repair bootloader.rar，Check "Program Boot Loaders",UnCheck "Program MMC device", Click Download
4) After complete, the port will change into Qualcomm HS-USB Diagnostics 9006
5) UnCheck Program boot loaders，Check Program MMC device，Select Qualcomm MMC port，Click Download again.
6) Wait for it to complete, disconnect phone.
7) Press and hold "vol -" then also press and hold Power button and connect the phone to the computer, now the device manager will display WP8 UEFI USB SimpleI/O Port.
8) Run Flash Tool , select ROM file / Config XML and click "Scan && Download".
9) When phone displays 100%, and the inscription OK. The process of flashing rom is complete. Now you need Reset the phone (press power button on 15 sec or remove battery). Flash tool displays information about the bad file FFU, just ignore it
10) Run device in mass storage mode
11) Run WP8CRUU.exe... BUT
No instrunction, only black console. when i close the console the copy begin.. but stop at 45% with "Error: cannot write 5 file. Error 5"
Suggestion?
SOLVED: must be waiting on the black console

I can not find Data\\PROGRAMS\\WINDOWSAPP directory，how can I get full FS access ？

[GUIDE] Enable VoLTE/VoWiFi on LineageOS 17.1 for EU carriers Oneplus 6T

[GUIDE] Enable VoLTE + VoWiFi for German and other EU carriers on the Oneplus 6T running LineageOS 17.1
Requirements:
- Phone must be rooted
- A computer running Windows to connect your phone with (Also tested Windows 7 running in Virtualbox)
- Qualcomm USB Driver (Downloadlink)
- Qualcomm PST Tool (Downloadlink)
- ADB
IMPORTANT: This can break your phone! Make a backup of your EFS Partition! This can be done with TRWP.
1)
Download and install Qualcomm USB Driver and PST Tool on your computer. Make sure, you have the adb tool as well.
2)
On your phone activate the hidden developer settings:
Settings -> About -> Build-Number (press it multiple times)
then
Settings -> System -> Devloperoptions
Activate:
Android-Debugging
Local Shell
Connect your phone to your computer.
3)
Open a shell on your computer and type:
Code:
adb shell
Watch your phone to accept the incoming connection from your computer.
Type:
Code:
su
and watch your phone again to accept root access.
Activate the Diagnostic Mode by typing:
Code:
setprop sys.usb.config diag,serial_cdev,serial_tty,rmnet_ipa,mass_storage,adb
Your phone will disconnect from adb, but thats ok.
4)
On your computer open "PDC" from the installed QPST application as admin.
In the device list, select your phone.
In the upcoming list look for "Oversea-Commercial_DS", right click it and deactivate Sub0 and Sub1
Click "Oversea-Commercial_DS" again and press the Remove button.
Close the PDC Tool and open it again.
Select your phone again
Look for Telefonica_UK_Commercial, right click and SetSelectedConfig for both Sub0 and Sub1
Click on Telefonica_UK_Commercial again and click the Activate button
Close the application
5)
Unplug your phone and reboot it.
Make sure you have activated VoLTE/VoWiFI in your settings.
6)
No VoLTE/VoWIFI icon is shown in the status bar. You can check the IMS status as followed:
Open the dialer and enter the code: *#*#4636#*#*
This will open the Testing menu. Select the first entry "Phone information".
In the option "Select phone index" you can choose your sim card you want to get information about.
Then, press the three dotted menu in the upper right and select "IMS Service Status"
If it says "IMS Registration: Registered" everything is working fine. Depending on whether you are on WiFi or LTE, "Voice over LTE" or "Voice over WiFi" will be shown as "Available as well.
Enjoy!

Great work. I'm on Linux. What is this qpst and psd tools for exactly and is there a way to do the changes from Linux?

Termehansen said:
Great work. I'm on Linux. What is this qpst and psd tools for exactly and is there a way to do the changes from Linux?
Click to expand...
Click to collapse
I'm on Linux too. Qpst is a USB Modem driver and PSD is a Tool to access and alter the modem firmware on the phone.
Unfortunately these will only run on Windows. I used VirtualBox and run Windows 7 (I bought a cheap license key some time ago) on it.

So none of these tools could be helpful?
https://github.com/openpst

Termehansen said:
So none of these tools could be helpful?
https://github.com/openpst
Click to expand...
Click to collapse
Interesting, I didn't know these tools. Maybe it could work.

Thank you for the guide. Still, I think you have a typo:
Sayonara123 said:
Code:
setprop sys.usb.config diag,serial_cdev,serial_tty,rmnet_ipa,mass_storage ,adb
Click to expand...
Click to collapse
There's a space preceding ',adb', and with blindly using this command something went wrong on my Windows PC. Had to restart. 'setprop' also supports only 2 arguments.
Another thing:
Sayonara123 said:
Remark:
I did not test it, yet. But you may have to repeat the procedure after every LineageOS update.
Click to expand...
Click to collapse
You should put that on top, maybe make it bold and set a bigger font. It looked like a tested and working method, I just blindly followed the instructions without questioning (also a mistake on my part).
Anyway, I followed the steps successfully but cannot see if VoLTE/VoWifi is functional as there is not indicator in LineageOS 17.1. If anyone knows a way, feel free to tell.
Thanks again.

Thank you for your reply.
martin.42 said:
Thank you for the guide. Still, I think you have a typo:
Click to expand...
Click to collapse
You are right, It's a typo, I didn't notice. Fixed it.
Another thing:
Click to expand...
Click to collapse
The whole procedure was tested on my own phone. There was just one unclear thing, whether these changes survive an update of the LineageOS system. It does! So I removed this obsolet remark.
Anyway, I followed the steps successfully but cannot see if VoLTE/VoWifi is functional as there is not indicator in LineageOS 17.1. .
Click to expand...
Click to collapse
Yes, it's a pitty there's no indicator in the status bar. I've found another way to check functionality and added it to the guide.
Hope this make things more clearly.
Thx

Tried it on stock oos 10.3.6, and windows 10. Have swedish carrier Tre (Hallon).
Works great! Thanks for your guide! ?

Procedure fails on OP6 with LineageOS20, phone is not visible in PDC.

How to add 5G configurations to your Pixel 5 (solved)

Hi all
Similarly to the Oneplus 8 series, Pixel 5 does not support 5G in countries that it is not sold in. For Oneplus, configurations could be changed using the Qualcomm QPST file manager.
https://mt-tech.fi/en/modify-oneplus-7-pro-5g-8-and-8-pro-nr-lte-a-band-combos/
However, using those instructions doen't work as I cant trigger engeneeringmode/factorymode.
Any idea how this could be triggered on Pixel 5 devices?

I'm also looking for advice on this, especially about adding VoLTE support aswell. Hopefully someone with more knowledge could provide some more information!

I'm even willing to contribute to a bounty

Is there anyone that understands how to get into engineering mode?

deepsync said:
Is there anyone that understands how to get into engineering mode?
Click to expand...
Click to collapse
AFAIK there is no engineering mode on Pixels. Apparently there is a Qualcomm tool that allows you to modify your EFS partitions to change your bands.
https://forum.xda-developers.com/pixel-5/help/t-mobile-5g-compatibility-t4171145/post83841425

There must be an engineering or factory mode - its a qualcomm chip isn't it?

I think I managed to activate engineering mode as QPST now regognizes my phone. I followed the steps by @cstark27 written here: https://forum.xda-developers.com/showpost.php?p=83499679&postcount=75
However, if I understood correctly, PDC tool is the one used to get VoLTE working on devices which are not certified between Google and a carrier by applying a vertified carrier's policy profily to your phone. Unfortunally, PDC does not regognize my phone for some reason. I really don't know what I should modify in EFS tool to enable 5G, VoLTE and more CA combos.
This has been an interesting but challenging project as I have combined steps from many tutorials designed for pixel and oneplus devices. But now I'm stuck and would love to hear comments from others who have tinkered around with these tools.

Is root a mandatory step? Wasn't for oneplus.

deepsync said:
Is root a mandatory step? Wasn't for oneplus.
Click to expand...
Click to collapse
At least in my experience, definatelly yes. I have no idea how the diagnosing mode could be activated without it.

Lemon200 said:
I think I managed to activate engineering mode as QPST now regognizes my phone. I followed the steps by @cstark27 written here: https://forum.xda-developers.com/showpost.php?p=83499679&postcount=75
However, if I understood correctly, PDC tool is the one used to get VoLTE working on devices which are not certified between Google and a carrier by applying a vertified carrier's policy profily to your phone. Unfortunally, PDC does not regognize my phone for some reason. I really don't know what I should modify in EFS tool to enable 5G, VoLTE and more CA combos.
This has been an interesting but challenging project as I have combined steps from many tutorials designed for pixel and oneplus devices. But now I'm stuck and would love to hear comments from others who have tinkered around with these tools.
Click to expand...
Click to collapse
I don't have the Pixel 5 anymore, but looking at the carrier_policy.xml noted in the MT-Tech article (https://mt-tech.fi/en/modify-oneplus-7-pro-5g-8-and-8-pro-nr-lte-a-band-combos/), then there is a section that explicitly enables 5G for the PLMN's given. (<!-- START RULE: Add carriers require to enable 5G -->) So you should try adding your carrier to that area, copying the file back (make a backup!!) and rebooting. You can reference the PLMN name from the list at the beginning of this file...look at the MCC-MNC combos and find yours. The linked article is a little more detailed about how to do this. Proceed at your own risk. Make sure you have backed up the original files, and have the stock images to reflash if necessary.
@Lemon200 if you don't have the GD1YQ Pixel 5, this website (run by Mt-Tech admin) would appreciate the CA combos info. You can get that info using the Qualcomm Diag instructions, then upload the file to his uploader below: https://cacombos.com/contribute
I don't know about PDC. Can't get it to recognize a device.

cstark27 said:
I don't have the Pixel 5 anymore, but looking at the carrier_policy.xml noted in the MT-Tech article (https://mt-tech.fi/en/modify-oneplus-7-pro-5g-8-and-8-pro-nr-lte-a-band-combos/), then there is a section that explicitly enables 5G for the PLMN's given. (<!-- START RULE: Add carriers require to enable 5G -->) So you should try adding your carrier to that area, copying the file back (make a backup!!) and rebooting. You can reference the PLMN name from the list at the beginning of this file...look at the MCC-MNC combos and find yours. The linked article is a little more detailed about how to do this. Proceed at your own risk. Make sure you have backed up the original files, and have the stock images to reflash if necessary.
@Lemon200 if you don't have the GD1YQ Pixel 5, this website (run by Mt-Tech admin) would appreciate the CA combos info. You can get that info using the Qualcomm Diag instructions, then upload the file to his uploader below: https://cacombos.com/contribute
I don't know about PDC. Can't get it to recognize a device.
Click to expand...
Click to collapse
What made you get rid of the pixel 5 @cstark27 ?

juandhi said:
What made you get rid of the pixel 5 @cstark27 ?
Click to expand...
Click to collapse
Pros/cons vs the 4 XL I already have But I'm gonna do the trade-in deal with T-Mobile to get half off a 4a 5G. Will just need to get it sim unlocked so I can root it.

cstark27 said:
I don't have the Pixel 5 anymore, but looking at the carrier_policy.xml noted in the MT-Tech article (https://mt-tech.fi/en/modify-oneplus-7-pro-5g-8-and-8-pro-nr-lte-a-band-combos/), then there is a section that explicitly enables 5G for the PLMN's given. (<!-- START RULE: Add carriers require to enable 5G -->) So you should try adding your carrier to that area, copying the file back (make a backup!!) and rebooting. You can reference the PLMN name from the list at the beginning of this file...look at the MCC-MNC combos and find yours. The linked article is a little more detailed about how to do this. Proceed at your own risk. Make sure you have backed up the original files, and have the stock images to reflash if necessary.
@Lemon200 if you don't have the GD1YQ Pixel 5, this website (run by Mt-Tech admin) would appreciate the CA combos info. You can get that info using the Qualcomm Diag instructions, then upload the file to his uploader below: https://cacombos.com/contribute
I don't know about PDC. Can't get it to recognize a device.
Click to expand...
Click to collapse
Thanks! I'll try enabling 5G when I have more time to mess around with QPST and upload the CA info aswell.

Could you please give an answer when you try it? I can't use in Spain the 5G network...

Good news everyone! I managed to enable 5G connectivity for my Pixel 5 in Finland. Thanks again to @cstark27 for hinting me to the right direction.
1. First you need to get your phone to show up in QPST. This is done similarly to Pixel 4 XL and you can find the the steps to do so here: https://forum.xda-developers.com/showpost.php?p=83499679&postcount=75
2. Once you have installed QPST open EFS tool. If you have followed the steps in the previous step and have the right drivers installed your phone shows up here. Now you need to navigate to the carrier policy file. More details here: https://mt-tech.fi/en/modify-oneplus-7-pro-5g-8-and-8-pro-nr-lte-a-band-combos/
3. PLEASE remember to backup the original file! Pixel 5's file is different from the OnePlus example linked above. I simply added 5G to every rat_capability field, saved the file and then replaced the original file with the modified one. As usual, you have all the responsibility of your device and its modifications.​
Now that 5G is working, all that's left is to find a way to enable VoLTE. Replacing MBN files has worked in other devices so perhaps it could be the solution here as well.

Lemon200 said:
Good news everyone! I managed to enable 5G connectivity for my Pixel 5 in Finland. Thanks again to @cstark27 for hinting me to the right direction.
1. First you need to get your phone to show up in QPST. This is done similarly to Pixel 4 XL and you can find the the steps to do so here: https://forum.xda-developers.com/showpost.php?p=83499679&postcount=75​
Click to expand...
Click to collapse
For some reason it is not working for me , i cant see my device qpst.. idk why i did it over 10 times now and still the same.
Is there anyway this is happening due to me using the method to bypass the safety net ? because for some reason my device shows as pixel 3a or something.
If you have the time can you give us the exact steps ? im pretty sure im missing something i just dont know what am i doing wrong.
Is there a way that i need specific drivers for QPST ?​

alawii_shark said:
For some reason it is not working for me , i cant see my device qpst.. idk why i did it over 10 times now and still the same.
Is there anyway this is happening due to me using the method to bypass the safety net ? because for some reason my device shows as pixel 3a or something.
If you have the time can you give us the exact steps ? im pretty sure im missing something i just dont know what am i doing wrong.
Is there a way that i need specific drivers for QPST ?
Click to expand...
Click to collapse
If you want to mess with QPST:
Code:
adb shell
su
resetprop ro.bootmode usbradio
resetprop ro.build.type userdebug
setprop sys.usb.config diag,diag_mdm,adb
diag_mdlog
cancel (ctrl+c) once it starts to "hang" at failed to open diag socket
change usb config (file transfer, no file transfer)
wait

mordof said:
If you want to mess with QPST:
Code:
adb shell
su
resetprop ro.bootmode usbradio
resetprop ro.build.type userdebug
setprop sys.usb.config diag,diag_mdm,adb
diag_mdlog
cancel (ctrl+c) once it starts to "hang" at failed to open diag socket
change usb config (file transfer, no file transfer)
wait
Click to expand...
Click to collapse
It actually worked bro ! Im so happy and sad now. I tried replacing the file but 5g still not working.
you mind sharing the carrier file you edited ? if it doesnt include any private info for sure.
when i open 4634
it shows
NR Available: False
NR State: NONE
NR Frequency: UNKNOWN ?
When I try to restrict it to NR ONLY the singal dies and shows no service..
can you confirm if this is normal or it should show available for NR ?

Lemon200 said:
Good news everyone! I managed to enable 5G connectivity for my Pixel 5 in Finland. Thanks again to @cstark27 for hinting me to the right direction.
1. First you need to get your phone to show up in QPST. This is done similarly to Pixel 4 XL and you can find the the steps to do so here: https://forum.xda-developers.com/showpost.php?p=83499679&postcount=75
2. Once you have installed QPST open EFS tool. If you have followed the steps in the previous step and have the right drivers installed your phone shows up here. Now you need to navigate to the carrier policy file. More details here: https://mt-tech.fi/en/modify-oneplus-7-pro-5g-8-and-8-pro-nr-lte-a-band-combos/
3. PLEASE remember to backup the original file! Pixel 5's file is different from the OnePlus example linked above. I simply added 5G to every rat_capability field, saved the file and then replaced the original file with the modified one. As usual, you have all the responsibility of your device and its modifications.​
Now that 5G is working, all that's left is to find a way to enable VoLTE. Replacing MBN files has worked in other devices so perhaps it could be the solution here as well.
Click to expand...
Click to collapse
Hi, can you please explain how can i add QPST to my phone?

alawii_shark said:
It actually worked bro ! Im so happy and sad now. I tried replacing the file but 5g still not working.
you mind sharing the carrier file you edited ? if it doesnt include any private info for sure.
when i open 4634
it shows
NR Available: False
NR State: NONE
NR Frequency: UNKNOWN ?
When I try to restrict it to NR ONLY the singal dies and shows no service..
can you confirm if this is normal or it should show available for NR ?
Click to expand...
Click to collapse
Are you sure you added 5G to every field possible? There are four rat_capability fields in the file so add 5g to every one of them to be sure, although I would guess that the last one is the one which matters. After uploading the modified file to your phone a restart is required. Also I think these configs are reset when sim card is changed.
EDIT: Also NR only won't work, as current 5G NSA networks still rely on 4G in many ways.
mordof said:
Hi, can you please explain how can i add QPST to my phone?
Click to expand...
Click to collapse
If by this you mean how to get your phone to show up in QPST, follow the original instructions here: https://mt-tech.fi/en/modify-oneplus-7-pro-5g-8-and-8-pro-nr-lte-a-band-combos/
You need to install the diag drivers and then use the adb shell commands you mentioned in your earlier post. Please read the articles linked in my original post. The diag mode on Pixel 5 is essentially enabled with the adb shell commands in order to use qpst.