Database Develop

Unbrick lg lte 2 f160 lsk qhsusb_dload no recovery no download mode

I brick my lg f160k while flashing wrong kdz on it. It was in no download no recovery mode. Pc was showing qhsusb_dloade 9008. I searched alot over the internet to unbrick it but found nothing except a thread on veitnam site by a veitnamis developer. Thanks to him for this useful thread. With the help of this i unbrick my cell. It was very difficult to understand the thread while in Vietnam's language but i managed to do so with the help of google translator. I thought i should must share it on xda to English community for easy umderstading. Hit thanks if you get your phone back. And many thanks to veitnamis developer too....
1. Download the qualcom drivers and install it from given link.
https://app.box.com/s/5n42md550n4oxne04xttfz788cp0i4i3
Open device manager and ensure that you have correctly installed qualcom 9008 drivers. Remember the com port
2. Download and unzip this folder
https://app.box.com/s/zvvj2v87csuwmv93k7ztzevuiytyd0fi
You shall have a tool Boar Diag v3.99c folder and two folder named S and L.
3.IMPORTANT. You will have to choose folder S For F160K and S and for F160L and LV choose Folder L.
4. Now run the tool.
Check the 2 points on tool
1.Ap check
2.Emmc Test
In Ap chipset choose board
For F160s and F160k
D1L(MSM8960 SKDA)
FOR 160L
D1L(MSM8960 LV)
Select Com Port shown in device manager of your computer.
In TARGET DIR Choose the Folder of Named S or L according to your modal, As i told you earlier in step 3
Rest all should be unchecked
PRESS START
https://app.box.com/s/hr8y0cmzcond0jciemprl5jzr4rllggn
Now test will start and will take 10 seconds to complete
If this test run successfully AP and EMMC should show pass on tool window
5. In this step Now only uncheck
Emmc Test and then check the
Boot Image Restore and select ABOOT from drop down menu.
Only w points Checked.
Ap Check
Boot Img Restor
Rest all should be uncheck the same as in previous step.
PRESS START
https://app.box.com/s/w1r560py2bm2wwlbtch9bn7kh1bski2u
Now it will Test the AP CHECK and will write Boot image to your mobile.
It will take 10 to 15 seconds.
After successfully completion of this test you ll see download mode on your mobile. Or you may see an LG logo with a secure boot massege.
Important...
STEP 6 was not mentioned in orignal thread. I did this at my own and got my result.
6. If you dont see download mode or LG logo after completing step 5 even successfully completion shown ion tool, As in mine case on F160k. Then try step 5 with AP CHIPSET with D1L(MSM8960 RR&G)
rest same selection.
AND PRESS START.
I hope this will resolve your issue. As i did.
7. NOW ITS TIME TO FLASH LATEST KDZ FIRMWARE ACCORDING TO YOUR MoBILE Phone.
.
THATS ALL WHAT I HAVE FOR MY FRIENDS.
IF I HELPED YOU THEN PLZ PRAY FOR ME. THANKS ALOT

Thank you for providing the files! I have a bricked LG LTE2 F160K, which mode should I put the phone be?
My phone can still access download mode, and when I try to start up the tool, it just says "Failed during loading flash programmer"

bro if your download mode is working then you will have to flash kdz of your modal for f160k I think its 20k. you can find the latest kdz many sites. google it lg firmware you can find it on vietnam site lgviet.com

this programe is only for qhsusb_delod mode. no download no recovery state. if you have download mode then kdz is the way to unbrick

Help! "device was not found in dload trying flash programmer" i get this error

What kind of brick you have? Its qhsusb bulk mode. Then this guide will help you

what is "ion took"??
there are no "D1L(MSM8960 RR&G)" in the selection

muzammil457 said:
What kind of brick you have? Its qhsusb bulk mode. Then this guide will help you
Click to expand...
Click to collapse
test completed but my phone didn't enter to download mode
the driver name when i connect my LG is"QHSUSB_QLOAD"

why yu no reply??

Have you installed qualcm drivers first? If no then do it if yes then in board ap choose msm8960 it will work. But if doesnt then there is 1 more 8960 selection try that

Does this method works for a sony xperia ion which has the same problem????

ahamedlaheer said:
Does this method works for a sony xperia ion which has the same problem????
Click to expand...
Click to collapse
This programe is for qualcom devices. If your experia is qualcom based then it will work. But u need to find the files to flash doe your modalm I have loaded only f160 system files.

muzammil457 said:
Have you installed qualcm drivers first? If no then do it if yes then in board ap choose msm8960 it will work. But if doesnt then there is 1 more 8960 selection try that
Click to expand...
Click to collapse
yes i install it, i tried the other msm8960 but it doesn't work

Test point to force qhsusb-dload in LG F160s
mcycharles said:
Thank you for providing the files! I have a bricked LG LTE2 F160K, which mode should I put the phone be?
My phone can still access download mode, and when I try to start up the tool, it just says "Failed during loading flash programmer"
Click to expand...
Click to collapse
Dear all,
Can some one provide me the details of test points for LG F160s i want to force it, as m phone in dead alsmost,,,
i will b very thankful
Rizwan

Why u need to do that if u r not in hard brick state?

muzammil457 said:
I brick my lg f160k while flashing wrong kdz on it. It was in no download no recovery mode. Pc was showing qhsusb_dloade 9008. I searched alot over the internet to unbrick it but found nothing except a thread on veitnam site by a veitnamis developer. Thanks to him for this useful thread. With the help of this i unbrick my cell. It was very difficult to understand the thread while in Vietnam's language but i managed to do so with the help of google translator. I thought i should must share it on xda to English community for easy umderstading. Hit thanks if you get your phone back. And many thanks to veitnamis developer too....
1. Download the qualcom drivers and install it from given link.
https://app.box.com/s/5n42md550n4oxne04xttfz788cp0i4i3
Open device manager and ensure that you have correctly installed qualcom 9008 drivers. Remember the com port
2. Download and unzip this folder
https://app.box.com/s/zvvj2v87csuwmv93k7ztzevuiytyd0fi
You shall have a tool Boar Diag v3.99c folder and two folder named S and L.
3.IMPORTANT. You will have to choose folder S For F160K and S and for F160L and LV choose Folder L.
4. Now run the tool.
Check the 2 points on tool
1.Ap check
2.Emmc Test
In Ap chipset choose board
For F160s and F160k
D1L(MSM8960 SKDA)
FOR 160L
D1L(MSM8960 LV)
Select Com Port shown in device manager of your computer.
In TARGET DIR Choose the Folder of Named S or L according to your modal, As i told you earlier in step 3
Rest all should be unchecked
PRESS START
https://app.box.com/s/hr8y0cmzcond0jciemprl5jzr4rllggn
Now test will start and will take 10 seconds to complete
If this test run successfully AP and EMMC should show pass on tool window
5. In this step Now only uncheck
Emmc Test and then check the
Boot Image Restore and select ABOOT from drop down menu.
Only w points Checked.
Ap Check
Boot Img Restor
Rest all should be uncheck the same as in previous step.
PRESS START
https://app.box.com/s/w1r560py2bm2wwlbtch9bn7kh1bski2u
Now it will Test the AP CHECK and will write Boot image to your mobile.
It will take 10 to 15 seconds.
After successfully completion of this test you ll see download mode on your mobile. Or you may see an LG logo with a secure boot massege.
Important...
STEP 6 was not mentioned in orignal thread. I did this at my own and got my result.
6. If you dont see download mode or LG logo after completing step 5 even successfully completion shown ion tool, As in mine case on F160k. Then try step 5 with AP CHIPSET with D1L(MSM8960 RR&G)
rest same selection.
AND PRESS START.
I hope this will resolve your issue. As i did.
7. NOW ITS TIME TO FLASH LATEST KDZ FIRMWARE ACCORDING TO YOUR MoBILE Phone.
. THATS ALL WHAT I HAVE FOR MY FRIENDS.
I have F160L.i tried same as u mention,All proceger complete but no download mode no fastboot mode no LG logo.What to do now?still on qualcomm 9008
Click to expand...
Click to collapse

Hello all
If after restore aboot phone not power on
Need restore all this file: about, Backupgpt, boot, dbi, laf, Primarygpt, recovery, rpm, tz, sdl1, sdl2, sdl3 (one by one, not MIX!!!) and after restore last sdl3 power turn on!

muzammil457 said:
I brick my lg f160k while flashing wrong kdz on it. It was in no download no recovery mode. Pc was showing qhsusb_dloade 9008. I searched alot over the internet to unbrick it but found nothing except a thread on veitnam site by a veitnamis developer. Thanks to him for this useful thread. With the help of this i unbrick my cell. It was very difficult to understand the thread while in Vietnam's language but i managed to do so with the help of google translator. I thought i should must share it on xda to English community for easy umderstading. Hit thanks if you get your phone back. And many thanks to veitnamis developer too....
1. Download the qualcom drivers and install it from given link.
https://app.box.com/s/5n42md550n4oxne04xttfz788cp0i4i3
Open device manager and ensure that you have correctly installed qualcom 9008 drivers. Remember the com port
2. Download and unzip this folder
https://app.box.com/s/zvvj2v87csuwmv93k7ztzevuiytyd0fi
You shall have a tool Boar Diag v3.99c folder and two folder named S and L.
3.IMPORTANT. You will have to choose folder S For F160K and S and for F160L and LV choose Folder L.
4. Now run the tool.
Check the 2 points on tool
1.Ap check
2.Emmc Test
In Ap chipset choose board
For F160s and F160k
D1L(MSM8960 SKDA)
FOR 160L
D1L(MSM8960 LV)
Select Com Port shown in device manager of your computer.
In TARGET DIR Choose the Folder of Named S or L according to your modal, As i told you earlier in step 3
Rest all should be unchecked
PRESS START
https://app.box.com/s/hr8y0cmzcond0jciemprl5jzr4rllggn
Now test will start and will take 10 seconds to complete
If this test run successfully AP and EMMC should show pass on tool window
5. In this step Now only uncheck
Emmc Test and then check the
Boot Image Restore and select ABOOT from drop down menu.
Only w points Checked.
Ap Check
Boot Img Restor
Rest all should be uncheck the same as in previous step.
PRESS START
https://app.box.com/s/w1r560py2bm2wwlbtch9bn7kh1bski2u
Now it will Test the AP CHECK and will write Boot image to your mobile.
It will take 10 to 15 seconds.
After successfully completion of this test you ll see download mode on your mobile. Or you may see an LG logo with a secure boot massege.
Important...
STEP 6 was not mentioned in orignal thread. I did this at my own and got my result.
6. If you dont see download mode or LG logo after completing step 5 even successfully completion shown ion tool, As in mine case on F160k. Then try step 5 with AP CHIPSET with D1L(MSM8960 RR&G)
rest same selection.
AND PRESS START.
I hope this will resolve your issue. As i did.
7. NOW ITS TIME TO FLASH LATEST KDZ FIRMWARE ACCORDING TO YOUR MoBILE Phone.
.
THATS ALL WHAT I HAVE FOR MY FRIENDS.
IF I HELPED YOU THEN PLZ PRAY FOR ME. THANKS ALOT
Click to expand...
Click to collapse
any other link for qualcomm drivers?

Link is fine. U can download it from google.

Need some Help
My phone goes to Service Mode but not in Download mode.
Should i try this method?
And how i can find out my phone is S OR K OR L originally hardware based
Waiting for your answer .
My phone is dead since 1 month

Micromax canvas A1 bricked, pls help!!!

hi,
my micromax a1 was runnning marshmallow 6.0.1 when during a security patch update installation got stuck and failed to boot again. now just booting into "dead android with exclamation mark". upon pressing power button and volume up and going into recovery(Android stock recovery) menu , cant wipe partition or data as it throws error "E: failed to mount/ cache" errors..
upon trying to install with any SD card also throws same error.
then i tried to install through ADB, while connecting to PC , PC not detecting mobile in recovery mode but detecting in bootloader mode. with fastboot flash command (for installing TWRP/CWM) in bootloader mode, error coming as "sending recovery failed(unknown status code)" .
Kindly help...

same happened to me yesterday . do you find any solution ??

Hi there !
STEP 1: DOWNLOAD the FLASH TOOL from this this link :LINK TO DOWNLOAD FILE
It is almost 30 MB in Size. And EXTRACT / UNZIP it to Desktop ( OR SOMEWHERE ) of your computer.
STEP 2: DOWNLOAD LOLLIPOP FLASH FILE
DOWNLOAD LINK FOR LOLLIPOP: HERE
After downloading this flash file EXTRACT / UNZIP it to Desktop ( OR SOMEWHERE ) on your computer.
STEP 3: NOW INSTALL DRIVERS:
YOU NEED TO BE ON WINDOWS 7 TO INSTALL DRIVERS (WINDOWS 8 DOESN'T SUPPORT THIS DRIVER / PHONE IS NOT DETECTED)
DOWNLOAD DRIVERS from this link : HERE
EXTRACT AND INSTALL THE DRIVERS : Next next next and finish If you see an security warning ( a red coloured pop up ) choose INSTALL IT ANYWAY
IT IS RECOMMENDED YOU TO RESTART YOUR PC.
STEP 4:
Now we have Extrated /unziped 2 files. One is FLASHTOOLS and other is FLASH FILE and Extracted it or unziped it to Desktop or Somewhere.
One of it having the name SP_Flash_Tool_exe_windows_v5.1424.00 or open both folders then one of it having the flashing tool. OPEN THE FOLDER NAMED SP_Flash_Tool_exe_windows_v5.1424.00
it contains an application named fashtool.exe OPEN IT
NOW THE APPLICATION IS ASKING FOR SCATTER LOADING FILE
its a txt file which is on the extracted flash file folder
BROWSE it by clicking Button named Scatter Loading
click OPEN
STEP 5:
HERE IN THE DROPDOWN BOX, IT SAYS DOWNLOAD ONLY, CLICK ON IT AND SELECT FIRMWARE UPDATE ONLY.
IF YOU SELECT FORMAT + DOWNLOAD, THEN YOU WILL LOOSE IMEI NUMBER.
NOW CLICK DOWNLOAD BUTTON ( GREEN ARROWED BUTTON NAMED DOWNLOAD )
IN CASE YOU LOOSE IMEI NUMBER, THEN REFER HERE
STEP 6:
Now SWITCH OFF your PHONE and REMOVE BATTERY
STEP 7:
CONNECT your PC via USB CABLE
wait for the driver Detection.
THE FLASHING PROCESS WILL START AUTOMATICALLY you can See the progress in progress bar which is on bottom of flashing tool Application.
WHEN IT IS FINISHED DISCONNECT USB AND RESTART YOUR PHONE.
NOW YOU WILL GET LOLLIPOP UPDATE IMMEDIATELY.
NOW REFER HERE TO ROOT MARSHMALLOW
HIT THANKS IF HELPED
if link do not work here properly then just google 'canvas a1 stuck on startup' ... and follow link in associated with xda

Device is dead
My phone is neither switching on, nor charging.
I flashed the stock ROM due to some problem with the rooted device through SP Flash tools. It completed successfully, but the device is not switching on or charging.
KIndly help

Unlock Bootloader, Convert L23 to L21 and upgrade to Android 6 Official & Custom

Huawei P8 Lite - Unlock Bootloader, Convert L23 to L21 and upgrade to Android 6 Official & Custom - (October 30, 2016).
IMPORTANT!
This tutorial describes the steps and necessary order to update the Huawei P8 Lite L23 or L21 to a newer version of Android. All in one tutorial to walk not looking separately each step is explained as much as I practice possible, if still do not achieve good for Re-Lean and try it as many times as necessary or ask if flat can not, if no then go for a beer and tacos, relax and try again later.
If you do not feel ready or deplano have not the foggiest idea of ​​what arises in this best Tutorial leave your cell like this, if you also have your phone you used to what is necessary as well leave it, dedicate to research terms you do not understand Moreover, do not try to "run without first learning to walk," you're not coming back Millionnaire, or you're going back more handsome, strong, and you will be the most intelligent or interesting, or you will become immortal only by Update your phone to Android in June , so be patient, be aware and do not hasten. At the precise moment you decide to continue with this tutorial, you become absolutely responsible for what happens to your phone and your actions. Please proceed with caution and do not play the chingon.
ODYSSEY BEGINS HERE!
UNLOCK BOOTLOADER
You can get the code to unlock the Bootloader in the following ways:
Following in the footsteps of EloyGomez Video Tutorial:
PD: Add a "w" to download.
https://ww.youtube.com/watch?v=AVmAEQjOnNQ
Following the Steps of taking screenshots and a previous orientation with EloyGomez Video:
https://plus.google.com/u/0/photos/+JohnMillerDev7/albums/6305181114976401569
Using "Huawei Product ID Generator" and following the instructions (I recommend you go copying data from a notebook and save them, you never know when you can return to need):
Download "Huawei Product ID Generator" extract it where they like and run. (It is a very simple little program).
Product Model: HUAWEI Y300-0000 (selecionan that model).
Product IMEI / MEID: "Here put your IMEI / MEID".
Product ID: "Here Product ID generates them automatically according to product model & product IMEI / MEID previously placed, and which must wear on the page"
Enter the page to Unlock Bootloader Huawei, Whether the version in English or Chinese, the only thing that changes is the language. They can try with 2 pages.
Create an account so that they can log in, they can also log in with Facebook, it is very simple.
Once you have created your account and logged in, we see the page for the unlock code.
Fill the fields with the data that we requested and put the following:
Product type: Smartphone
Product model: HUAWEI Y300-0000 (If you do not work with this, try with all models that are in the generator) (Also try with CAPITALS & lowercase).
Product Serial number: They get in Settings> About phone> Status> Serial Number.
Product IMEI: They get in Settings> About phone> Status> IMEI.
Product ID: They get the "Huawei Product ID Generator" (The program that generated them a while ago).
Captcha place the page requesting them and pressed Send or Submit, you must give the unlock code for Bootloader, copy it into the notebook (which I suppose must carry).
Now Turn to Settings> About Phone and Pulsen several times on "Compilation" until muentre them the message "now are a developer" Returning to Settings and you will see the option "Developer" tab, go there, if they are not active options because the activated developer, now a little move down and activate "USB debugging".
Download the "UNLOCK HUAWEI BOOTLOADER" extract it where they like, then connect your phone to the PC and run "UNLOCK BOOTLOADER.bat" program.
And the rest is a cinch, just follow the instructions anger us indicating the program, Drivers ADB & HiSuite (At most only have to accept the terms, click next and finish) were installed, the phone will restart a few sometimes they do not worry or despair pANIC not normal will reboot.
When they unlocked the Bootloader can disconnect your phone from the PC on and off.
Now let's check that everything went well, keep pressed "Vol-" while we connect to the PC, you will see a white screen with some letters (that's the Fastboot mode), and if they see the text "PHONE UNLOCKED" because Congratulations, Make unlocked the bootloader correctly.
Hechate a beer, a soft drink, Pau-Pau or commits a loaf to celebrate, but do not get too excited because it only been the beginning, we still some way to go, but certainly this is the most important step of all, because without having the unlocked Bootloader is not at all advisable to make root the phone, install a recovery or install a custom ROM, those using KingRoot arise after them so rare mistakes and to get them to damage the phone.
OFFICIAL FOR HUAWEI UNLOCK CODE BOOTLOADER:
https://emui.huawei.com/en/plugin.php?id=unlock&mod=detail
HUAWEI OFFICIAL VERSION IN CHINA FOR UNLOCK CODE BOOTLOADER:
PD: Add a "w" to see the website.
https://ww.emui.com/plugin.php?id=unlock&mod=detail
TOOLS YOU NEED TO DOWNLOAD:
Bootloader unlock huawei:
https://mega.nz/#!uRkC2DQS!R2IMpEpUAtrDH4-Gi4VLi8Mcz5_h98jtKsBATpMBQYg
Huawei Generator Product ID:
https://mega.nz/#!eE81BbrT!_JBTy1ZCdFuYd7JwFLnaQe06I47ua__hEa4GHx6PZvM
If the PC does not recognize them the phone even after the program to automatically install the ADB drivers, then download, extract and install these, is not all that complicated should only connect your phone to the PC.
Run programs just follow the instructions and go. May need to click on Next, Finish, "Y" or "ENTER".
https://mega.nz/#F!SZM21JKa!gE1IWif0EJH6-UwrJWQBAg
CONVERT L21 To L23
(If you reached this step means that are already Pros .... hahaha Wes is not true, it is believed!, Read on!)
At this point what we will do first is to install the TWRP Recovery and make full Wipes in order to erase the system and leave the phone in white to make a much cleaner installation without errors. So we follow the following instructions:
PD: You can install the TWRP who like V2 or V3, the procedures are the same, just change a bit the interface.
Instructions for both versions:
Download TWRP INSTALL RECOVERY (V2 or V3) P8 HUAWEI LITE.rar
Download adb-setup-1.4.3.rar
Unzip adb-setup-1.4.3.rar and run the program. (This is for adb drivers and pc can detect the terminal is installed.)
We will see a blue screen console Type "and" or "accept" in everything and close the window. If you ask them to restart the pc, do it and go.
Begin your phone in Fastboot mode; Turn off the phone and press the "VOL" key and without releasing conectenlo to the PC until Fastboot screen appears.
Unzip "INSTALL RECOVERY TWRP (V2 or V3) HUAWEI LITE.rar P8" and execute the file "INSTALL RECOVERY TWRP (V2 or V3) HUAWEI LITE.bat P8" and follow the steps.
Do not take more than 5 minutes is just a matter of going press ENTER.
Turn off the phone and Start TWRP Recovery Mode (Vol + & Power) Click on WIPE, Advanced Wipe and make full wipes:
Should be marked:
Dalvik
Cache
Data
Internal storage
System
IMPORTANT !: not marques "micro sdcard".
Return to Menu, press Reboot, and then Bootloader.
Files:
TWRP V2:
https://mega.nz/#!SZkzlQCb!iKBl1-6arjT6_9exrp9sc2aVzp7NnuKxECz6MVJ_Oms
TWRP V3:
https://mega.nz/#!CZ91RQSA!B_kl3YPn7H38nbyG-5bVk2yt6qGDSsu3A2cnGysj7u4
ADB:
https://mega.nz/#!eY1giTYD!cPs8mlBxgVP8DLHgWhCmf6Ay9hi56aTOEps55CVwiHU
After you have successfully done this, we continue to spend our L23 to L21 P8 Lite, I recommend removing your SD card and SIM Card precaution. We follow the instructions:
Downloading "FlashRom C432B052 (Lollipop 5.0, 3.1 EMUI) Dual Sim Transition" extract it where they like, Begin your phone in Fastboot mode, connect it to PC, execute the "FLASH-ALL.bat" file (not execute permissions administrator), and follow the instructions that tells the program.
You complete the process when the phone is started with the new system, if you are targeting "About phone" say "Balong". To remove that must be installed Step2.
Downloading "Step2", extract it, look for the "UPDATE.APP" file and copy it to the "DLOAD" your SD card folder if you do not have then created. (Clearly it must first insert the SD on the phone).
Then head to Settings> Updater> Menu> Update Local and selecionan the UPDATE.APP (Step2). The phone will reboot, start the installation and wait for it to finish. When you start the system and check the "About phone" no longer tell Balong but L21.
After this I recommend doing a factory reset, first remove your SD card, then go to "Settings> Security> Backup and Restore" or type in the search bar settings "Backup and Restore" click "Factory Data Reset "mark" Delete memory ", press" Reset "and wait to finish the process. If for some reason out "Failed" do not worry just restart, anyway there will reset the cel, also do not worry if you have no signal or you will not detect the SIM, that is fixed by installing the following update.
Congratulations you get past your cel L21!
Files:
FlashRom C432B052:
https://mega.nz/#!LQNimCgQ!oq2C_Gwvwv7zoigo8GR2kstPdHDO5ESJ9Qglv_2UERs
Step2:
https://mega.nz/#!vdsDEZSb!3FIgh6WNgP4NWRfnGoDxisd1wAQk3CBPKdKl8_If-v0
UPDATED ANDROID 6 Official
The update command is as follows: "B052> B170> B560> B564" or "B052> B170> B550> B560> B564"
(Compiling B560 is the most stable so far).
Being in the B052 just have to download the following Compilaciones and be updated locally via:
"B170> B560> B564" or "B170> B550> B560> B564". I recommend that for every update they make, do a factory reset to eivtar errors, this is optional in the end, I just do them the recommendation from experience.
The B170 downloaded, extract the files, copy the DLOAD UPDATE.APP folder on your SD, head to Settings> Updater> Menu> Update Local and selecionan the UPDATE.APP, the phone restarts, start the installation and wait end.
Now being in the B170, repeat the previous step to install the B550 or B560 Compilation. (Depending on the order above mentioned update, they work better or decide to take)
Now when they are on the B560 turn to the B564 but no longer appear the option "Update Local", so there are 2 options to perform the update: (and must have the UPDATE: APP previously copied to the DLOAD, the update.app always be copied to Dload no other):
Option 1:
Type the following code in the app called "* # * # 2846579 # * # *" ​​(without quotes obviously).
Appear the famous hidden menu, click "Software Upgrade"> "SDCard Upgrade"> will leave them a message "Are you Sure" (are you sure?), Pressed OK, start the update and wait for it to finish.
Option 2:
Cel being off or on, press the (Vol-, Vol +, Power) aperezca keys until the update screen and wait to finish the process.
And that would be all, Congratulations and cell habras updated to Android in June!
If you get here it means you're half Pro.
Official Roms (Installation Via Local):
PD: Add "http:" extension links to download.
B170:
//download-c.huawei.com/download/downloadCenter?downloadId=57325&version=181091&siteCode=fi
B550:
//download-c.huawei.com/download/downloadCenter?downloadId=78426&version=312720&siteCode=es
B560:
//download-c.huawei.com/download/downloadCenter?downloadId=80469&version=319382&siteCode=pl
https://mega.nz/#!uRNRDRaA!zavgQtBakqdg_lbXmgoKwB7qotPoXOJvJofvnPlM1CI
B564:
https://mega.nz/#!aAVhkbgI!1cGtLB0HxQN0x-KeyB2MqQ3JWeGEnvD2aKll7vsCa60
UPDATED CUSTOM ROM ANDROID 6
Just click on the link, read the post and go following the instructions that you indicate. Patience and Success!
PD: Add "http" "://" "w" to see the website.
[TUTORIAL] Install Android B560 & B564 6 (Dual Sim) Custom Rom V2 - Sokkoban - (Updated July 18, 2016)
ww.htcmania.com/showthread.php?t=1188059
Rom ROM Spectre - Android 6 B560 (Dual Sim) - POST UPDATED (26 AUGUST 2016)
ww.htcmania.com/showthread.php?t=1200900
Rom ROM Phenom - Android 6 B564 (Dual Sim) - POST UPDATED (26 August 2016)
ww.htcmania.com/showthread.php?t=1220243
Rom ROM Opteron - Android 6 B574 (Dual Sim) - POST UPDATED (26 AUGUST 2016)
ww.htcmania.com/showthread.php?t=1218158
Nautilus Android ROM Rom 6 B564 (Dual Sim) - October 13, 2016
ww.htcmania.com/showthread.php?t=1241126
Rom ROM Helios - 6 B890 EMUI Android 4.1 (Dual Sim) - October 25, 2016.
ww.htcmania.com/showthread.php?t=1245909
DRIVERS EXTRAS
Here I leave some Drivers Extras to troubleshoot issues fastboot, adb, if the PC does not detect the Cell, the installation of each is very simple, just keep connected your cel to the PC, run programs, you must give "next" and then restart the PC if necessary.
Files:
https://mega.nz/#F!SZM21JKa!gE1IWif0EJH6-UwrJWQBAg
And that's all I hope I have been clear and supported with this Tutorial.
Greetings from Coatzacoalcos, Veracruz, Mexico! :fingers-crossed:

Huawei P8 Lite Unlock Bootloader, Convert L23 In L21, Upgrade To Android 6 Official +

# SUPPORT HUAWEI P8 LITE
Huawei P8 Lite Unlock Bootloader, Convert L23 In L21, Upgrade To Android 6 Official + Install Custom Roms, Recoverys, Rootear, And Many Many Things - April 27, 2017 Updated.
IMPORTANT! This Tutorial describes the steps and order needed to Update the Huawei P8 Lite L23 or L21 to a newer version of Android. Everything in a single tutorial so that they are not looking for each step separately, It is explained as practical as possible, even if they do not do it well. Re-read and try it as many times as necessary or ask if they can not, if not As they go for a beer and tacos, they relax and try again later.
If you do not feel ready or deplaned you do not have the slightest idea of ​​what is posed in this tutorial better leave your cell phone like this, if you have your cell phone you use for the necessary so leave it, dedicate yourself to investigate terms that you do not understand Even, do not try to "run without first learning to walk", you are not going to return Millionaire, nor are you going to become more handsome, strong, nor will you be the most intelligent or interesting, nor will you return immortal solo by Update your phone to Android 6 , So be patient, be aware and do not accelerate. At the moment you decide to continue with this Tutorial, you become absolutely responsible for what happens with your Mobile and your actions. Please proceed with caution and do not play chingon.
HERE THE ODYSEA BEGINS!
<<< UNLOCK BOOTLOADER >>>
IMPORTANT:
To know the Model Number & IMEI:
Enter Settings> About Phone.
To Know the Serial Number:
Enter Settings> About Phone> Status
To Know Product ID:
Enter this code: "* # * # 1357946 # * # *" ​​on the telephone dial (without quotes), the number that appears, is the PRODUCT ID.
You can Obtain the Code to unlock the Bootloader in the following ways:
Following in the footsteps of EloyGomez Video Tutorial:
Https://www.youtube.com/watch?v=AVmAEQjOnNQ
---------------------------------------------------------------------------------------------------------
Following the Steps of the Screenshots having already a previous orientation with the Video of EloyGomez:
Https://plus.google.com/u/0/photos/+JohnMillerDev7/albums/6305181114976401569
Using "Huawei Product ID Generator", and following the instructions (I recommend copying the data obtained in a notebook and saving them, you never know when you may need them again):
Download "Huawei Product ID Generator", extract it wherever you like and run it. (It's a very simple program).
Product Model: HUAWEI Y300-0000 (select that model).
Product IMEI / MEID: "Here they place their IMEI / MEID".
Product ID: "Here you generate the Product ID automatically according to the Product model & product IMEI / MEID that they placed above, and it is the one they should use on the page"
Go to the Huawei page to unlock Bootloader, either the English version or the Chinese version, the only thing that changes is the language. You can try with all 2 pages.
They create an account so they can log in, they can also log in with Facebook, it's very simple.
Once you have created your account and logged in, we will see the page to obtain the unlock code.
Fill in the fields with the data that we are requested and we will put the following:
Product type: Smartphone
Product model: HUAWEI Y300-0000 (If it does not work for them, try all the models that are in the generator) (Also try with CAPITAL & lowercase).
Product Serial number: You get it in Settings> About Phone> Status> Serial Number.
Product IMEI: You get it in Settings> About Phone> Status> IMEI.
Product ID: They get it with the "Huawei Product ID Generator" (the one that generated the program a while ago).
They place the Captcha that asks them for the page and they press Submit or Submit, they must give them the Code of Unlock for the Bootloader, they copy it in the scrapbook (that I suppose they must take).
Now go to Settings> About Phone and click on "Compilation" several times until the message "now you are a developer" is muted, you return to Settings and you will see the "Developer Options" tab, enter there, if the options are not active Of developer because they activate them, now they move a little down and activate "Depuracion USB".
Download the program "UNLOCK BOOTLOADER HUAWEI", Extract where you like, then connect your phone to the PC and run "UNLOCK THE BOOTLOADER.bat".
Already the rest is eaten, just follow the instructions that will indicate the program, the ADB & HiSuite Drivers will be installed (At most, they will only have to accept the terms, press next and finish), the Telephone will restart a few Sometimes do not worry or despair do not panic, it will be normal to restart.
When they have unlocked the Bootloader they can disconnect the Phone from the PC and turn it off.
Now let's check that everything went well, we kept pressing "Vol-" and at the same time we connected it to the PC, they will see a white screen with some letters (that is the Fastboot mode), and if they see the text "PHONE UNLOCKED" Congratulations, you have unlocked the bootloader correctly.
Make a beer, a soda, a Pau-Pau or Commit a Bread to celebrate, but do not get so excited because this is only the beginning, we still have a way to go, but certainly This is the most important step of all, Since without having the Bootloader unlocked it is not at all advisable to make Root to the phone, to install a recovery or to install a custom Rom, Those that use KingRoot for that after that they appear rare errors to them and even it damages them the telephone.
---------------------------------------------------------------------------------------------------------
OFFICIAL HUAWEI PAGE TO OBTAIN THE BOOTLOADER UNLOCK CODE:
Https://emui.huawei.com/en/plugin.php?id=unlock&mod=detail
OFFICIAL PAGE OF HUAWEI IN CHINESE VERSION TO OBTAIN THE BOOTLOADER UNLOCK CODE:
Https://www.emui.com/plugin.php?id=unlock&mod=detail
TOOLS YOU SHOULD DOWNLOAD:
Unlock bootloader huawei: https://mega.nz/#!uRkC2DQS!R2IMpEpUAtrDH4-Gi4VLi8Mcz5_h98jtKsBATpMBQYg
Huawei Product ID Generator: https://mega.nz/#!eE81BbrT!_JBTy1ZCdFuYd7JwFLnaQe06I47ua__hEa4GHx6PZvM
If the PC does not recognize the phone even after the program installs the ADB Drivers automatically, then download, extract and install these, it is not at all complicated just connect your phone to the pc.
Run the programs just follow the instructions and you're done. You may have to press Next, Finish, "Y" or "ENTER".
Https://mega.nz/#F!SZM21JKa!gE1IWif0EJH6-UwrJWQBAg
---------------------------------------------------------------------------------------------------------
<<< CONVERT L23 IN L21 >>>
(If they already reached this step means that they are already Pros .... hahahaha not true, they believed it!, Keep reading!)
At this point what we will do first is to install the Recovery TWRP and make the Wipes Complete with the purpose of Erase the system and leave the Phone blank to make a Installation much Cleaner and without possible errors. To do this we follow the following instructions:
PS: They can install the Twrp that like V2 or V3, the procedures are the same, only slightly changes the interface.
Instructions for both versions:
Download INSTALAR RECOVERY TWRP (V2 or V3) HUAWEI P8 LITE.rar
Download adb-setup-1.4.3.rar
Unzip adb-setup-1.4.3.rar and run the program. (This is to install adb drivers and the pc can detect the terminal.)
You will see a blue console screen, type "and" or "accept" at all and close the window. If you ask them to restart the pc, do it and that's it.
Start your Phone in Fastboot mode; Switch off the phone and press the "vol-" key and without releasing it connect it to the PC until the Fastboot screen appears.
Unzip "INSTALL RECOVERY TWRP (V2 or V3) HUAWEI P8 LITE.rar" and execute the file "INSTALL RECOVERY TWRP (V2 or V3) HUAWEI P8 LITE.bat" and follow the steps.
It will not take more than 5 minutes just to press ENTER.
Turn off Cell Phone and Start in Recovery Mode TWRP (Vol + & Power), Press WIPE, Advanced Wipe and make the complete wipes:
You must dial:
Dalvik
Cache
Data
Internal storage
System
IMPORTANT !: Do not check "micro sdcard".
Go back to Menu, press Reboot, and then Bootloader.
Files:
TWRP V2:
Https://mega.nz/#!SZkzlQCb!iKBl1-6arjT6_9exrp9sc2aVzp7NnuKxECz6MVJ_Oms
TWRP V3:
Https://mega.nz/#!CZ91RQSA!B_kl3YPn7H38nbyG-5bVk2yt6qGDSsu3A2cnGysj7u4
ADB:
Https://mega.nz/#!eY1giTYD!cPs8mlBxgVP8DLHgWhCmf6Ay9hi56aTOEps55CVwiHU
Once the above is done correctly, we continue to move our P8 Lite L23 to L21, I recommend you remove your SD Card and SIM Card as a precaution. Follow the instructions:
Download "FlashRom C432B052 (Lollipop 5.0, EMUI 3.1) Dual Sim Transition", extract it wherever you like, start your phone in Fastboot mode, connect it to the PC, execute the file "FLASH-ALL.bat" (do not execute it with permissions Administrator), and follow the instructions given to you by the program.
When the process ends, the phone will start with the new system, if you go to "About the phone" it will say "Balong". To remove that you must install Step2.
Download "Step2", extract it, look for the file "UPDATE.APP" and copy it to the "DLOAD" folder of your SD Card, if you do not have it then create it. (It is clear that you must first insert the SD into the phone).
Then go to Settings> Updater> Menu> Local Update and select the UPDATE.APP (Step2). The phone will restart, the installation will begin and wait for it to finish. When you start the system and check in "About the phone" you will no longer say Balong, but L21.
After this it is recommended to do a factory reset, first remove your SD card, then go to "Settings> Security> Backup and Restore" or type in the search bar of "Backup and Restore" settings, press "Reset factory data "Check" Clear internal memory ", click on" Reset "and wait for the process to finish. If for some reason "Failed" does not worry, it only restarts, the cell will have been reset anyway, do not worry if you do not have a signal or it does not detect the SIM, that is fixed by installing the next update.
Congratulations, you've already passed your cel to L21!
Files:
FlashRom C432B052: https://mega.nz/#!LQNimCgQ!oq2C_Gwvwv7zoigo8GR2kstPdHDO5ESJ9Qglv_2UERs
Step2: https://mega.nz/#!vdsDEZSb!3FIgh6WNgP4NWRfnGoDxisd1wAQk3CBPKdKl8_If-v0
---------------------------------------------------------------------------------------------------------
<<< UPDATE ANDROID 6 OFFICIAL >>>
The update order is as follows: "B052> B560> B564> B574> B584> B594> B596> B598> or" B552> B570> B560> B560> B564> B574> B584> B594> B596> B598 ".
Being already in the B052 we only have to download the following Compilations and go updating via local:
"B552> B570> B560> B564> B594> B594> B594> B596> B598 'or' B552> B570> B560> I recommend that for every update they make, make a factory reset to avoid possible errors, this is optional after all, I only make the recommendation from their own experience.
Download the B170, extract the files, Copy the UPDATE.APP to the DLOAD folder of your SD, go to Settings> Updater> Menu> Local Update and select the UPDATE.APP, the phone will restart, the installation will begin and wait for To finish.
Now on the B170, Repeat the previous step to install the B550 or B560 Compilation. (Depending on the order of updating mentioned above, that works best for them or decide to take)
Now when they are in the B560 we go to the B564 but the option of "Local Update" will no longer appear, so we have 2 options to carry out the update: (they should already have the UPDATE: APP previously copied in the DLOAD, The update.app is always due to copying to Dload there is no other):
Option 1:
Write the following code in the calls app "* # * # 2846579 # * # *" ​​(without quotes obviously).
The famous hidden menu will appear, click on "Software Upgrade"> "SDCard Upgrade"> you will receive an "Are you Sure" message, press OK, start the update and wait for it to finish.
Option 2:
While the Cel is off or on, press the keys (Vol-, Vol +, Power) until you see the update screen and wait for the process to finish.
And that would be Todo, Felicidades ya habras updated Your phone to Android 6!
If you've already come up here means you're half Pro.
Official Roms (Local Via Installation):
ALE-L21C432B170
Https://mega.nz/#!eYUgxbrb!yccoxiIsXjIHdiGxdP6AU05S1fYQGNNMRba427BxEgs
ALE-L21C432B550
Http://download-c.huawei.com/download/downloadCenter?downloadId=78426&version=312720&siteCode=en
ALE-L21C432B560
Http://download-c.huawei.com/download/downloadCenter?downloadId=80469&version=319382&sit eCode=pl
Https://mega.nz/#!uRNRDRaA!zavgQtBakqdg_lbXmgoKwB7qotPoXOJvJofvnPlM1CI
ALE-L21C432B564
Https://mega.nz/#!kJkESTKT!1cGtLB0HxQN0x-KeyB2MqQ3JWeGEnvD2aKll7vsCa60
ALE-L21C432B574 - 2016.07.19
Http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v56678/f1/full/update.zip
ALE-L21C432B580
Https://mega.nz/#!2RUgxKiI!c-RX4wJsilZuxEDFwWJ2lcO-tpC4J5Q3uGbHUo4c1Vw
ALE-L21C432B584 - 2016.11.21
Http://update.hicloud.com:8180/TDS/data/files/p3/s15/G753/g104/v67128/f1/full/update.zip
ALE-L21C432B586 - 2016.12.13
Http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1084/g104/v69882/f1/full/update.zip
ALE-L21C432B588 - 2016.12.26
Http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1084/g104/v72428/f1/full/update.zip
ALE-L21C432B594 - 2017.02.28
Http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1084/g104/v77344/f1/full/update.zip
ALE-L21C432B596 - 2017.03.28
Http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1084/g104/v80333/f1/full/update.zip
ALE-L21C432B598 - 2017.04.20
Http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1084/g104/v83472/f1/full/update.zip
---------------------------------------------------------------------------------------------------------
<<< INSTALL CUSTOM ROMS, RECOVERYS, ROOTEAR, AND MANY MORE THINGS >>>
I have compiled a collection of various interesting contributions to facilitate your search, so check it out!
Http://www.htcmania.com/showthread.php?t=1310020
*
<< DRIVERS EXTRAS >>
Here I leave some extra drivers to solve problems with issues of fastboot, adb, in case the PC does not detect the mobile, the installation of each is very simple, just keep your cell connected to the pc, run the programs, you have to Give it to "next" and restart the PC if necessary.
Files:
Https://mega.nz/F!SZM21JKa!gE1IWif0EJH6-UwrJWQBAg#F!SZM21JKa!gE1IWif0EJH6-UwrJWQBAg
And that's it, I hope I was clear and supported with this Tutorial,
Greetings from Mordor!
---------------------------------------------------------------------------------------------------------

Empty

Im trying to use huawei product id generator but I always get this message in unlock page
I tried with c8812 and Y300-000 and all have the same results.
ALE-L21
Please make sure the verification code and model number are correct. If your device has multiple IMEIs or MEIDs, please try another IMEI or MEID.

[GUIDE] How to return to Stock/Flash Images with QFIL

Here is a step by step guide on how to flash the stock rom with QFIL and by extension any image.
Download and install the Qualcomm drivers from here
Download either of the firmware from here
Download the support files (Firehose/rawprogram0.xml/patch0.xml) here
Extract the firmware and support files to the same folder so you can easily access them like your desktop
Download and install QPST from here
Open the QFIL application (Find it in your start menu)
In the "Select Build Type" field select Flat Build
In the "Select Programmer" field navigate to the folder you extracted the firmware and support files to and select the prog_emmc_firehose_8909.mbn file
Select the "Load XML" button and navigate to the folder you extracted the firmware and support files to and select the rawprogram0.xml and then the patch0.xml when prompted.
Plug in your tablet
Run the following adb command "adb reboot edl" (Now the screen should be blank but the led light should be red)
If the text at the top of the QFIL application says "No Port Available" click the "Select Port..." option and pick your device. If your device isn't showing up there you didn't install the drivers properly.
Click the Download Button to begin flashing your device
So the above explains how to flash everything if you want to flash individual partitions you can edit your rawprogram0.xml to only include the ones you want. (patch0.xml stays the same) I have linked below 2 examples, one of them flashes just a boot.img and one that just flashes the recovery.img. But you aren't limited to those.
Recovery
Boot

Mine just in case

Awesome, thanks for this post! it will really help us in upcoming projects!

Managed to revive my phone using the B12 files but it crashes after completing system.img, I think the problem is userdata.img, my phone boots but I lost the imei and I don't know how to get it back, I'm still trying.

ZTE 971 not recognized by either QPST or QFIL
Thanks for all the detailed instructions. But my ZTE 971 is not visible to either qpst or qfil eventhough the phone shows in windows 8.1. In the Developer Options menu, I noticed Select USB Configuration, RNDIS (USB ethernet) option cannot be enabled. I wonder if this has anything to do with it. OEM unlocking, USB debbugging are already selected. Any suggestions, please? Thanks.
ps. I live in Turkey. I got this phone last year from AT&T and have unlocked the sim.

My PC is not detecting my ZTE MAVEN 3
I have installed all drives but still facing the issue. I am using it on Windows 10.

I flashed the B13 (ZPST tool shows my device as B13) with the QFIL like your guide says and it says all completed successfully and finishes, but now my phone went from only being able to boot EDL + FTM + Recovery, to now booting directly to EDL mode, which obviously means this guide completely screwed up my phone... Thanks.

Mega says that link for the driver is invalid, but the driver is included in your QPST download anyway.

000Nick said:
I flashed the B13 (ZPST tool shows my device as B13) with the QFIL like your guide says and it says all completed successfully and finishes, but now my phone went from only being able to boot EDL + FTM + Recovery, to now booting directly to EDL mode, which obviously means this guide completely screwed up my phone... Thanks.
Click to expand...
Click to collapse
solucionaste hermano
Mod edit:
you solved brother
Click to expand...
Click to collapse

it says qhsusb_bulk when I connect the the software is not working in the mobile and it is stuck at bootloader screen but I used the press both buttons to go to edl mode method and it said in the device manager a device connected with name : qhsusb_bulk
help pls

Hello All.
I am not able to get the following files
rawprogram.xml and patch.xml for LG G8x​Please help me to get this files ASAP as i have hard bricked the mobile, all partitions deleted