Database Develop

Runnning the unlocker step-by-step

This excruciating step-by-step might help someone...
Wherever I mention establishing a WMDC/AS connection, make damn well sure that the connection is established... If you don't, you won't kill your device, but you won't unlock either.
-Establish a WMDC(Vista) or Activeysnc connection(XP)
-Confirm this!
-Start the unlocker program on your PC.
-Click "Flash SPL" (Step 1)
-Click "Yes"
-On the Treo you are prompted to allow the install of itsutils.dll and jumpspl.exe. Say YES to both.
*****The Treo will reboot. Don't click anything on the PC until the treo is back up and a WMDC/AS connection is re-established
-On your PC, you will see "Cheetah RUU". Click Next.
-Click Next again
-Click Next
-Click Update
-Click Next
-Click Next
******The Treo will reboot into bootloader mode and flashing begins. The device will reboot after the flash completes. Don't click anything on the PC until the Treo is back up and a WMDC/AS connection is re-established
-Click finish
-Click "Unlock Radio" (Step 2)
-Click Next
-Click Next
-Click next
-Click Update
-Click Next
-Click Next
******The Treo will reboot into bootloader mode and flashing begins. The device will reboot after the flash completes. Don't click anything on the PC until the Treo is back up and a WMDC/AS connection is re-established
-Click Finish
-On the PC is a notice "Read this through!". Confirm that you have a good WMDC/AS connection.
-Click OK
-On the Treo click "Yes" to allow athena unlock.exe
-On the Treo follow the instructions - check off SIM and CID unlock
-On the Treo click "Unlock" and wait for it to finish, then click OK on the athena unlocker on the Treo, and then click OK on the Treo to close the athena unlocker.
-On the PC, click OK
-Ensure you still have a WMDC/AS connection.
-On the PC, click "Flash normal radio" (Step 3)
proceed through the series of "Next", the device will go into bootloader mode and flash one more time. The device will reboot when done, and you should be all set.

Hey Summiter. Thanks for your tutorial. Got one question. I've done the whole process and now my SPL-says 1.40.01 OliNex. So I'am assumming that all went well. The only thing that gets me is that in you guide you state that this process will hard reset my device and all info. will be lost. My information as well as my programs all remained intacked. Is this OK. or am I missing something.
Thanks.

My bad..it won't do a hard reset. My device hard reset when I was running a different process, not the released unlocker. =) Sorry to cause concern.
As for the slow 3G speeds, Olipro is looking into it.
manfly9884 said:
Hey Summiter. Thanks for your tutorial. Got one question. I've done the whole process and now my SPL-says 1.40.01 OliNex. So I'am assumming that all went well. The only thing that gets me is that in you guide you state that this process will hard reset my device and all info. will be lost. My information as well as my programs all remained intacked. Is this OK. or am I missing something.
Thanks.
Click to expand...
Click to collapse

summiter said:
My bad..it won't do a hard reset. My device hard reset when I was running a different process, not the released unlocker. =) Sorry to cause concern.
As for the slow 3G speeds, Olipro is looking into it.
Click to expand...
Click to collapse
Thanks for your quick response.

Can anyone check Radio Ver after last step
Can someone verify the Radio Ver after 3rd step (Normal Radio Flashed Back to Device) , Olipro said to my post that by having Radio at 1.16 , i didnt complete last (3) step , but i defenatly did , and my Radio still 1.16 , where i had 1.52 before unlocking ???????????????????
Hitec

I called cingular tonight because i have been trying to get my 750 paired with my tom tom one 3rd edition for use of the weather updates and cameras and such. Through conversation with a support representative, and trying to troubleshoot why it couldn't use the wireless connection of the phone, the representative asked me to check a few things on my phone. While answering some questions, one of which was about device software and such and i told him i had windows mobile 6 installed.
From this point on he led into reasons why i should be using it with out it being released and such which is to be expected. He also stated that doing to much to the phone can possibly make the phone upgradable when the real WM6 update is released. This he mentioned were changing the boot loader, IPL and SPL software in the phone, that and using bogus releases of software. The reason being he said was that the soon to be released update probes the phone deeply because everything has been updated including the boot loader stuff.
Now i cant confirm or deny any truth to these statements but the only thing i had done with mine was a try a few new firmwares but after my conversation with them i quickly reverted back to WM5.

jhowle said:
From this point on he led into reasons why i should be using it with out it being released and such which is to be expected. He also stated that doing to much to the phone can possibly make the phone upgradable when the real WM6 update is released. This he mentioned were changing the boot loader, IPL and SPL software in the phone, that and using bogus releases of software. The reason being he said was that the soon to be released update probes the phone deeply because everything has been updated including the boot loader stuff.
Click to expand...
Click to collapse
F.U.D.
That's utter ****ing bull****, the RUU will do no such ****ing thing, and even if it does, there'll still be a base NBH to dump and flash... complete crap.
the bootloader might well have been updated, but the Hard-SPL one on there isnt going to let it overwrite it, mate.

jst passing on the info dude,, don't blame me.. they said it

mines unlocked anyway, but i did a remote unlock with GSM libeerty.com only cocts 39 bux and it does work. i figured if i spent 39 bux and avoided the potential of bricking my treo than it is worth it.

jhowle said:
mines unlocked anyway, but i did a remote unlock with GSM libeerty.com only cocts 39 bux and it does work. i figured if i spent 39 bux and avoided the potential of bricking my treo than it is worth it.
Click to expand...
Click to collapse
well not really, but you paid your money and took your choice

i guess i just see how the HARD SPL really does any different besides bypass the lock function. I have tried some very similar programz with my black berries and even after they said they were unlocked you could still goto the SIM CARD Screen under advanced options and hold ALT and press M - E - P - 2 and walla the code entry screen window would still come up.

after completing step 2, I don't even have the option to install athena unlock.exe ?
Also, it gives me an error after I click "Read this through"
What's going on?
Am I doing something wrong?
EDIT:
itsutils.dll didn't even install
During step 1, jumpspl and enterbootloader are installed, NOT ITSUTILS
Any help is appreciated

Why no flash?
I just tried running the unlocker. I have an AT&T branded and locked Treo 750 with Windows Mobile 6. When I run the unlocker, it installed itsutils.dll the first time, but the freeze that i am supposed to look for never occured. Then it installs the jumpspl.exe, and restarts. Then i wait until the ActiveSync is reconnected, and run the RUU. The RUU says that it fails flashing either radio (the patched one or the stock one) after 7%, and gives me an error. But then the unlocker application ran on the phone, and said it was successfully unlocked. I check the SPL version and there is nothing about 1.40 OliNex. Is there a step that I am obviously missing? I thought i had to CID unlock it first, but it gives me the option to CID unlock and it says it is unnecessary on the unlocker itself. Im sorry for being such a bonehead, but any suggestions? Thanks.

just goto www.gsmliberty.com it onlu cocts 39.99 for a remote unlock and there is no risk of bricking ur phone

unhandled exception error
Treo 750 with AT&T running WM5 trying to unlock to use on another GSM carrier. Downloaded the current treo 750 unlock software from this site. after step 2 I get unhandled exception error and cannot continue. Phone is synced properly and I have followed all steps to the "t".
I see this question asked many times throughout the site but never an answer. can someone let me know what causes it and how to fix it. I know lots of people would appreciate it.
Thanks in advance for your time.

JBoever said:
Treo 750 with AT&T running WM5 trying to unlock to use on another GSM carrier. Downloaded the current treo 750 unlock software from this site. after step 2 I get unhandled exception error and cannot continue. Phone is synced properly and I have followed all steps to the "t".
I see this question asked many times throughout the site but never an answer. can someone let me know what causes it and how to fix it. I know lots of people would appreciate it.
Thanks in advance for your time.
Click to expand...
Click to collapse
I think I manually copied the Athenaunlock.exe to the phone and ran it at that step. Note - this was after the special "unlock" radio had already been flashed. Finally, I did a hard reset and then installed a new OS - ROW 2.23 which previously would not load on phone (because it was locked).
I hope this helps.

unlock not working. unhandled exception
I get the following error after I finish the radio patch and it trys to run athen unlock.exe
Unhandled exception has occurred in your application. If you lcick continue, the application will ignore this erro and attempt to continue. If you click Quit. The appication will close immediately. (below are the details)
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.ComponentModel.Win32Exception: The system cannot find the file specified
at System.Diagnostics.Process.StartWithCreateProcess(ProcessStartInfo startInfo)
at System.Diagnostics.Process.Start()
at AthenaUnlocker.Form1.runExecutable(String path, String args, String wdir)
at AthenaUnlocker.Form1.button2_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/Microsoft.NET/Framework/v2.0.50727/mscorlib.dll
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System/2.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
zip
Assembly Version: 0.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System.Windows.Forms
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Windows.Forms/2.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Drawing/2.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.

Same issue
Am currently trying to run from the SD card after updating .NET. Keep you posted

Can't get past the .NET error despite reloading latest version of .NET
Suggestions anyone?

alerner1 said:
I get the following error after I finish the radio patch and it trys to run athen unlock.exe
Unhandled exception has occurred in your application. If you lcick continue, the application will ignore this erro and attempt to continue. If you click Quit. The appication will close immediately. (below are the details)
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.ComponentModel.Win32Exception: The system cannot find the file specified
at System.Diagnostics.Process.StartWithCreateProcess(ProcessStartInfo startInfo)
at System.Diagnostics.Process.Start()
at AthenaUnlocker.Form1.runExecutable(String path, String args, String wdir)
at AthenaUnlocker.Form1.button2_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/Microsoft.NET/Framework/v2.0.50727/mscorlib.dll
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System/2.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
zip
Assembly Version: 0.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System.Windows.Forms
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Windows.Forms/2.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Drawing/2.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.
Click to expand...
Click to collapse
And NOW?????????

How to backup Roms?

Hi all, I'm new to the rom modification, I just want to know is there any guild for rom backup/restore for my x1? Thanks!

Have a look at SPB Backup. Quite useful

Forgive me if you find these questions stupid, but I'm a beginner
Is it sure that SPB Backup can backup/restore "the complete" ROM? I mean, if I backup the Vodafone ROM and than flash the WWE ROM, will it be possible to restore the Vodafone ROM? And if so: a) will it be restored with Radio and SPL or b): will it be necessary to restore stock Radio and stock SPL afterwards? And if b), how can I backup the stock Radio and SPL?

No, SPB Backup does NOT backup your ROM, nor does any other backup app do it (Resco, Sprite, etc.)
Those apps only create a backup of the contents of your C: drive (files, apps, registry settings, etc.)
Search the forum for how to 'dump a ROM'.

myth.71 said:
No, SPB Backup does NOT backup your ROM, nor does any other backup app do it (Resco, Sprite, etc.)
Those apps only create a backup of the contents of your C: drive (files, apps, registry settings, etc.)
Search the forum for how to 'dump a ROM'.
Click to expand...
Click to collapse
If you do search the X1 forum for "dump a ROM" you only get your post.

grayme said:
If you do search the X1 forum for "dump a ROM" you only get your post.
Click to expand...
Click to collapse
I said 'the forum', not 'the X1 forum'..
Don't know, if it'll work on the X1, but he might have a look at the tutorials for other devices in order to get a rough idea of how this is being done.
Am I right ?
Thanks..

I'm doing just that myself, (searching the whole forum and indeed the whole internet).
I've given up asking for help from people on here...

There's been loads on here about dumping/rebuilding/cooking roms!
Right listen carefully I shallsaydisonlywunce I'm not going to give you links to everyfile as you need to learn to search properly.
So here's how to dump your own Xperia rom.
Get itsutils or XDA-tools (same thing) specifically pdocread, search for them in the main wiki
download the latest
extract it to a folder somewhere sensible on your computer
start up CMD window
inside the CMD window navigate to the folder you extracted the tools to
the following came from following the first result by typing "dump rom" into the search at the top of the forum
Courtesy of Pof
type
pdocread.exe -l
you'll get something like this
| 3.12M (0x31f000) Part00
| 3.50M (0x380000) Part01
| 69.38M (0x4560000) Part02
| 134.38M (0x8660000) Part03
the bits in brackets are the important ones as you need to use what it says on YOUR device in the following
Type one at a time
pdocread -w -d FLASHDR -b 0x800 -p Part00 0 0x31f000 Part00.raw
pdocread -w -d FLASHDR -b 0x800 -p Part01 0 0x380000 Part01.raw
pdocread -w -d FLASHDR -b 0x800 -p Part02 0 0x4560000 Part02.raw
pdocread -w -d FLASHDR -b 0x800 -p Part03 0 0x8660000 Part03.raw
substituting what it says on your CMD window into the bit before the Part0
Wait quite a long time, the last two are bit partitions.
If it works congratulations you now have 4 raw files, that's your rom that is.. ahh isn't it cute
----------------
Rebuild it
Download the Kovsky Kitchen.
Extract it to C:KovskyKitchen
open KovskyKitchen folder,
go into that folder, in Vista make sure that buildos+package_tools is able to run as administrator
copy your 4 raw files to baserom folder (you don't need all 4)
Download the stock UK rom, (there's one listed under the HardSPL thread that works fine) extract the RUU_signed.nbh to Baserom folder as well.
There are decent walkthroughs for cooking roms, this kitchen is built on the Kaiser Kitchen, guess what you find if you type Kaiser kitchen tutorial in the search at the top of the forum
However first you need to extract what youve done so far
Start the kovskykitchen.cmd
it'll start up a new CMD window with some options.
select (e) extract a rom
then (b)
and let it work through
when it's finshed it'll go back to the main menu
now select (c) cook a rom
then (b)
it'll start up buildos + Package tools prog
select the buildos tab
select load rom navigate to your kovskykitchen folder. press ok.
after a couple of seconds the green go arrow will light up press it.
it'll do lots and may come back with an imgfs error, but this doesn't seem to matter, I only saw this once and it didn't effect the rom I don't think.
when it's done close the window.
back in the CMD window it'll be waiting for a keypress
then it processes a lot of files.
finally it'll popup with some info for the HTC rom tool
click BUILD!
select Kovsky from the dropdown box
press the 3 little dots ... next to the box that says OS
select the OS-NEW.nb in the main kovsky kitchen folder
Press BUILD! at the bottom, and give the file a sensible name, RUU_signed.nbh if you want to flash it from windows, Kovsimg.nbh if you want to flash it from microSD card
Close the htc_rom_tool when it's done and it'll popup a hexeditor to change the Pagepool and an immediate error that it can't find the nbh file.
If you just want to back up the rom of your device then close this window
and that's it all done..
now wheres my nappy wipes..
***
If you don't know what a terminal or CMD window is then I would advise not bothering to try backing up your roms or cooking
I'm sure someone will be along soon to tell me it's all wrong, but that's what I've done and it worked.

Thanks, and I genuinely mean that.
Shame you had to use that tone, I for one was getting there (I was starting to compile) but there was no simple how to (which was why you searched a lot and it seemed to help that you knew what you were looking for).
However, I now have a backup of the ROM I purchased, and for that I am grateful to you.

grayme said:
Thanks, and I genuinely mean that.
Shame you had to use that tone, I for one was getting there (I was starting to compile) but there was no simple how to (which was why you searched a lot and it seemed to help that you knew what you were looking for).
However, I now have a backup of the ROM I purchased, and for that I am grateful to you.
Click to expand...
Click to collapse
That's cool, if you've learnt something then we all win

Solution below the text
IHi When I follow what you describe above, I get the follwing problem:
C:\x1img>pdocread.exe -l
Copying C:\x1img\itsutils.dll to WCE:\windows\itsutils.dll
Could not update itsutils.dll to the current version, maybe it is inuse?
try restarting your device, or restart activesync
or maybe your device is application-locked.
I tried restarting both progs but to no prevail. Any idea anyone what to do?
Thank you
H
Solution
Pls check my thread : http://forum.xda-developers.com/showthread.php?t=454799 I tried to be as detailed as I could

Yes you need a registry editor and have to change some in HKLM. if you search dump rom on the site there is a tutorial that explains how to dump the rom.
i need help making the 4 .raw files into a rom image!

Raxxx said:
Yes you need a registry editor and have to change some in HKLM. if you search dump rom on the site there is a tutorial that explains how to dump the rom.
i need help making the 4 .raw files into a rom image!
Click to expand...
Click to collapse
READ THIS THREAD look 2 posts above what you wrote!

Hey fards,
Great guide. Its spot on so congrats there....( for a newbie like me ) and the same for all others that have left helpful advise on this thread..)
If you dont mind, I'd like to ask a question?
With reference to the:
"Download the stock UK rom, (there's one listed under the HardSPL thread that works fine) extract the RUU_signed.nbh to Baserom folder as well."
Do you know what that file does? I assume it holds the config of whats required?
Anyhows..... I happened to already downloaded one that was floating about on the forums: VFUK-rebuilt_RUU_signed.zip
So I used that one. Not sure if it would be any different or make any difference from the stock UK rom?? being as the guy stated his RUU file was for anybody that needed a clean Vodaphone UK rom.
Do you know if theres a way to verify the RUU files? with regards to version? or anything like that? Or am I just barking up the wrong tree.
Just curious....
Anyway once again. Great guide. Its well appreciated especially for guys like me that like to mess about with stuff like this.
Kind Regards,
King

From what I understand the RUU file gives the kitchen the proforma to rebuild the dumped rom files, kind of like a Template.

... = open file.

Extracting Radio ROM
Hi Fards...
Thanks to your great instructions, I have finally extracted my ROM to a 172,422kb RUU_signed.nbh file.
Two things that crosses my mind now is
1) Is there a way I can confirm if the ROM is intact and error free?
2) How about the Radio ROM? How can I extract that too?
(tried at wiki to search "extracting radio rom" and "radio rom extraction" but no results?
Thanks

I am having the following error when I try to build os:
Code:
Could not find the file 'C:\KovskyKitchen\ROM\ON.NB'
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.IO.FileNotFoundException: Could not find file 'C:\KovskyKitchen\ROM\OS.NB'.
File name: 'C:\KovskyKitchen\ROM\OS.NB'
at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath)
at System.IO.FileStream.Init(String path, FileMode mode, FileAccess access, Int32 rights, Boolean useRights, FileShare share, Int32 bufferSize, FileOptions options, SECURITY_ATTRIBUTES secAttrs, String msgPath, Boolean bFromProxy)
at System.IO.FileStream..ctor(String path, FileMode mode, FileAccess access, FileShare share)
at System.IO.File.ReadAllBytes(String path)
at Azpo5w0NHIg1f.AGpHL1cdnU(.wonx5u9()
at Azpo5w0NHIg1f.AGpHL1cdnU(.uk5()
at Azpo5w0NHIg1f.AGpHL1cdnU(.p6cw5(Object , EventArgs )
at System.Windows.Forms.ToolStripItem.RaiseEvent(Object key, EventArgs e)
at System.Windows.Forms.ToolStripButton.OnClick(EventArgs e)
at System.Windows.Forms.ToolStripItem.HandleClick(EventArgs e)
at System.Windows.Forms.ToolStripItem.HandleMouseUp(MouseEventArgs e)
at System.Windows.Forms.ToolStripItem.FireEventInteractive(EventArgs e, ToolStripItemEventType met)
at System.Windows.Forms.ToolStripItem.FireEvent(EventArgs e, ToolStripItemEventType met)
at System.Windows.Forms.ToolStrip.OnMouseUp(MouseEventArgs mea)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ScrollableControl.WndProc(Message& m)
at System.Windows.Forms.ToolStrip.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/Microsoft.NET/Framework/v2.0.50727/mscorlib.dll
----------------------------------------
ezencryption_lib
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/assembly/GAC_32/mscorlib/2.0.0.0__b77a5c561934e089/mscorlib.dll
----------------------------------------
System.Windows.Forms
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Windows.Forms/2.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System/2.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
System.Drawing
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Drawing/2.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
License
Assembly Version: 1.0.0.0
Win32 Version: 2.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/assembly/GAC_32/mscorlib/2.0.0.0__b77a5c561934e089/mscorlib.dll
----------------------------------------
ziplib
Assembly Version: 1.0.0.0
Win32 Version: 2.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/assembly/GAC_32/mscorlib/2.0.0.0__b77a5c561934e089/mscorlib.dll
----------------------------------------
buildos+package_tools-2.7
Assembly Version: 1.0.0.0
Win32 Version: 2.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/assembly/GAC_32/mscorlib/2.0.0.0__b77a5c561934e089/mscorlib.dll
----------------------------------------
Microsoft.VisualBasic
Assembly Version: 8.0.0.0
Win32 Version: 8.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/Microsoft.VisualBasic/8.0.0.0__b03f5f7f11d50a3a/Microsoft.VisualBasic.dll
----------------------------------------
System.Runtime.Remoting
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Runtime.Remoting/2.0.0.0__b77a5c561934e089/System.Runtime.Remoting.dll
----------------------------------------
System.Xml
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.42 (RTM.050727-4200)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Xml/2.0.0.0__b77a5c561934e089/System.Xml.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.

I am also having this problem as well?
Could not find the file 'C:\KovskyKitchen\ROM\ON.NB'

kiwiandy said:
I am also having this problem as well?
Could not find the file 'C:\KovskyKitchen\ROM\ON.NB'
Click to expand...
Click to collapse
Do not post the same problem in more than one thread. This thread was over two weeks old and you already created your own.
I wish I could help you with this issue, but I think fards can tell you more.

HardSPL Crashes windows 7

Hi all,
My hardspl crashes in windows 7 ultimate 32bit.
Any thoughts what I'm doing wrong?
Application Version: 0.0.0.0
Application Timestamp: 21000000
Fault Module Name: Rhodium-HardSPL_V2_00R3.exe
Fault Module Version: 0.0.0.0
Fault Module Timestamp: 21000000
Exception Offset: 000000c4
Exception Code: c0000005
Exception Data: 00000008
OS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789

Htchanes said:
Hi all,
My hardspl crashes in windows 7 ultimate 32bit.
Any thoughts what I'm doing wrong?
Application Version: 0.0.0.0
Application Timestamp: 21000000
Fault Module Name: Rhodium-HardSPL_V2_00R3.exe
Fault Module Version: 0.0.0.0
Fault Module Timestamp: 21000000
Exception Offset: 000000c4
Exception Code: c0000005
Exception Data: 00000008
OS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789
Click to expand...
Click to collapse
Hi try running exe as administrator

Thanks for the speedy reply
New error
roblem Event Name: BEX
Application Name: Rhodium-HardSPL_V2_00R3.exe
Application Version: 0.0.0.0
Application Timestamp: 21000000
Fault Module Name: Rhodium-HardSPL_V2_00R3.exe
Fault Module Version: 0.0.0.0
Fault Module Timestamp: 21000000
Exception Offset: 000000c4
Exception Code: c0000005
Exception Data: 00000008
OS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789
Regards
hanes

re-download the HardSPL again. Right click and run as admin as stated above but under the compatibility tab select Windows XP. See if that works for you.

Thanks for the responses, but still no success
Set comp. to Windows XP Pack 2
Run as adim (I'm always in admin mode anyways, but set it there just incase)
and still same
stopped working error
Regards
Hanes

i had this once or twice.....i just disabled all antivirus\firewall n other security stuff....n it worked fine

try disabling the UAC

Great info everyone but....
I've disabled UAC (should have done that a long time ago) and still error.
Nuked all the virus and firewall... and still error
Any more?
Regards
Hanes

Htchanes said:
Great info everyone but....
I've disabled UAC (should have done that a long time ago) and still error.
Nuked all the virus and firewall... and still error
Any more?
Regards
Hanes
Click to expand...
Click to collapse
"format c:"

Sounds like it could be a problem with your PC/installation. HardSPL is usually fine on Win7.

ScooterG said:
"format c:"
Click to expand...
Click to collapse
hehehehe

Haha fun guyz.
Still no luck for the Hardspl and my pc.

When you have Windows7 Profession, Enterprise, or Ultimate you can try it in "Windows XP Mode" (Not to be Confused with Compatiblity Mode).
"microsoft.com/windows/virtual-pc/download.aspx"
(I cant post links now, so just Copy&Paste it in you Adress Bar)
Google a bit for "Windows XP Mode" if you want how to use it, i´m too tired now....

I have the same problem and tried everything mentioned here before, but it didn't work.
Then I ran the Rhodium-HardSPL_V2_00R3.exe in XP Mode and it works, but I seems to be impossible to install Active Sync 4.5 in XP Mode...

Shani Ace said:
I have the same problem and tried everything mentioned here before, but it didn't work.
Then I ran the Rhodium-HardSPL_V2_00R3.exe in XP Mode and it works, but I seems to be impossible to install Active Sync 4.5 in XP Mode...
Click to expand...
Click to collapse
If you put your phone in bootloader mode, as long as the drivers are loaded for the "device" you can do whatever needs to be done without activesync.
:OTHER OPTION:
Go buy a cheap xp computer

please post your questions/problems about hardspl in the appropriate thread, not start a new one.
thread closed, not rom development.

[Q] Rooting troubles

Hello,
I was looking for some help. I was using Perception 9.5 for several months, but decided it was time to change. I used Odin to wipe my Captivate. Now I'm trying to re-root so I can flash Serendipity. I've been running into some trouble getting my phone rooted again though. I've tried several different ways. Most recently, I tried the "One click root" format. When I get to the "root" click, it gives me back "Unhandled exception has occured in your application...
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.ComponentModel.Win32Exception (0x80004005): The system cannot find the file specified
at System.Diagnostics.Process.StartWithShellExecuteEx(ProcessStartInfo startInfo)
at System.Diagnostics.Process.Start()
at System.Diagnostics.Process.Start(ProcessStartInfo startInfo)
at WindowsApplication1.Form1.Button1_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 (RTMRel.030319-0100)
CodeBase: file:///C:/Windows/Microsoft.NET/Framework/v4.0.30319/mscorlib.dll
----------------------------------------
Galaxy One Click Root
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Users/Collin/One%20click%20root/Galaxy_One-Click_Root.exe
----------------------------------------
Microsoft.VisualBasic
Assembly Version: 10.0.0.0
Win32 Version: 10.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/Microsoft.VisualBasic/v4.0_10.0.0.0__b03f5f7f11d50a3a/Microsoft.VisualBasic.dll
----------------------------------------
System
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System/v4.0_4.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
System.Core
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Core/v4.0_4.0.0.0__b77a5c561934e089/System.Core.dll
----------------------------------------
System.Windows.Forms
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Windows.Forms/v4.0_4.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Drawing/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
System.Runtime.Remoting
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 (RTMRel.030319-0100)
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Runtime.Remoting/v4.0_4.0.0.0__b77a5c561934e089/System.Runtime.Remoting.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box."
I also decided to try "Chaos Central"'s Captivate root from Android forums. I renamed the files to update.zip, but can't figure out where to copy them to.
Any help would be appreciated. Thanks a lot.

xThaNaturalx said:
Hello,
I was looking for some help. I was using Perception 9.5 for several months, but decided it was time to change. I used Odin to wipe my Captivate. Now I'm trying to re-root so I can flash Serendipity. I've been running into some trouble getting my phone rooted again though. I've tried several different ways. Most recently, I tried the "One click root" format. When I get to the "root" click, it gives me back "Unhandled exception has occured in your application...
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.ComponentModel.Win32Exception (0x80004005): The system cannot find the file specified
at System.Diagnostics.Process.StartWithShellExecuteEx(ProcessStartInfo startInfo)
at System.Diagnostics.Process.Start()
at System.Diagnostics.Process.Start(ProcessStartInfo startInfo)
at WindowsApplication1.Form1.Button1_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 (RTMRel.030319-0100)
CodeBase: file:///C:/Windows/Microsoft.NET/Framework/v4.0.30319/mscorlib.dll
----------------------------------------
Galaxy One Click Root
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Users/Collin/One%20click%20root/Galaxy_One-Click_Root.exe
----------------------------------------
Microsoft.VisualBasic
Assembly Version: 10.0.0.0
Win32 Version: 10.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/Microsoft.VisualBasic/v4.0_10.0.0.0__b03f5f7f11d50a3a/Microsoft.VisualBasic.dll
----------------------------------------
System
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System/v4.0_4.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
System.Core
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Core/v4.0_4.0.0.0__b77a5c561934e089/System.Core.dll
----------------------------------------
System.Windows.Forms
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Windows.Forms/v4.0_4.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 built by: RTMRel
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Drawing/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
System.Runtime.Remoting
Assembly Version: 4.0.0.0
Win32 Version: 4.0.30319.1 (RTMRel.030319-0100)
CodeBase: file:///C:/Windows/Microsoft.Net/assembly/GAC_MSIL/System.Runtime.Remoting/v4.0_4.0.0.0__b77a5c561934e089/System.Runtime.Remoting.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box."
I also decided to try "Chaos Central"'s Captivate root from Android forums. I renamed the files to update.zip, but can't figure out where to copy them to.
Any help would be appreciated. Thanks a lot.
Click to expand...
Click to collapse
I guess the first questions are,
did you flash back to JF6? did you do a Master Clear? Which version of Odin did you use?
I use One Click all the time, and have no issues at all
Edit** Oh yeah, have you enabled debugging on your device?

why are you even bothering to go through the trouble of rooting?
there are literally thousands of copies of the update.zip floating around here that you need in order to boot straight into CWM....in fact, heres another one
you dont even need to boot into your stock 2.1 in order to begin flashing...

I already got through the master clear with Odin3, so that wasn't a problem. It's just getting the root files to read that I'm having trouble with.
I was rooting because I need a root for Titanium backup. I have all my apps saved to that, and I will need to re-install them all once I get a new ROM flashed. What does that zip file do?

xThaNaturalx said:
I already got through the master clear with Odin3, so that wasn't a problem. It's just getting the root files to read that I'm having trouble with.
I was rooting because I need a root for Titanium backup. I have all my apps saved to that, and I will need to re-install them all once I get a new ROM flashed. What does that zip file do?
Click to expand...
Click to collapse
that zip file is clockworkmod recovery
if you need to root to do a TiBu, have you tried SuperOneClick?
http://forum.xda-developers.com/showthread.php?t=803682
enable usb debugging

I'm sorry, that's what the error was from. The big one that I listed was the error that I received from SuperOneClick. I can't figure out where to go from there.

You do not need to root. Use the clockwork mod update.zip posted on this thread. Reinstall packages twice, install zip from SD, choose, flash rom. Done
Sent from my Captivate using XDA Premium App

Am I supposed to be copying the zip to the internal or external SD then?

Okay, I did install, choose, then it has "meta-inf", "res", or "sbin". Which do I choose?

xThaNaturalx said:
Okay, I did install, choose, then it has "meta-inf", "res", or "sbin". Which do I choose?
Click to expand...
Click to collapse
please step away from your captivate
you didnt 'install' anything. copy the .zip to your internal sdcard....reboot into recovery, reinstall packages, it will reboot back into recovery, reinstall packages again and you will be in clockworkmod recovery
THIS WILL NOT DO A TITANIUM BACKUP FOR YOU!
if you really need the TIBU, i suggest you fix your java problems on your computer

mcord11758 said:
You do not need to root. Use the clockwork mod update.zip posted on this thread. Reinstall packages twice, install zip from SD, choose, flash rom. Done
Sent from my Captivate using XDA Premium App
Click to expand...
Click to collapse
This is what I was doing. I reinstalled packages twice. Then i Did "install zip from sdcard", then "choose zip from sdcard", and then I don't know where to go from there.

xThaNaturalx said:
This is what I was doing. I reinstalled packages twice. Then i Did "install zip from sdcard", then "choose zip from sdcard", and then I don't know where to go from there.
Click to expand...
Click to collapse
when you select 'choose zip from sdcard' you point it to the rom you want to install.
i would highly suggest you read a little more before you break your phone....you dont sound too confident

That's what I've been trying to do. I'm not very confident at all about it. But I was following what he said in reply to your zip file.

xThaNaturalx said:
That's what I've been trying to do. I'm not very confident at all about it. But I was following what he said in reply to your zip file.
Click to expand...
Click to collapse
from what it sounds like, you unzipped the rom somewhere?
you dont unzip anything when it comes to flashing....you just point it to the actual ZIP file to flash

Pirateghost said:
from what it sounds like, you unzipped the rom somewhere?
you dont unzip anything when it comes to flashing....you just point it to the actual ZIP file to flash
Click to expand...
Click to collapse
I didn't end up unzipping it. I didn't finish the last step of his process because I couldn't figure out what the last one was and didn't want to mess it up. Thank you again for all your help so far though.

xThaNaturalx said:
I didn't end up unzipping it. I didn't finish the last step of his process because I couldn't figure out what the last one was and didn't want to mess it up. Thank you again for all your help so far though.
Click to expand...
Click to collapse
his last step is 'flash rom'
what is confusing about that...point the 'choose zip' to the rom.zip thats on your internal sdcard.....select it and thats it.....it will flash the rom. then you reboot and you have new rom

Pirateghost said:
his last step is 'flash rom'
what is confusing about that...point the 'choose zip' to the rom.zip thats on your internal sdcard.....select it and thats it.....it will flash the rom. then you reboot and you have new rom
Click to expand...
Click to collapse
Well I just successfully got the root complete and Serendipity flashed. Thank you for all your help.

Question Bricked with Black Screen. See on windows devices list account not ADB fastboot

My phone is has an unlocked bootloader, I had TWRP but i think i mistakenly formatted the recovery partition.
Now my phone is black screen only. It makes a noise when connected to PC but thats all. I have tried abd devices nothig listed
I tried me flash tool but it cant install driver -
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.IO.DirectoryNotFoundException: Could not find a part of the path 'C:\Users\n\Desktop\folder\MiFlash20181115\log\[email protected]'.
at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath)
at System.IO.FileStream.Init(String path, FileMode mode, FileAccess access, Int32 rights, Boolean useRights, FileShare share, Int32 bufferSize, FileOptions options, SECURITY_ATTRIBUTES secAttrs, String msgPath, Boolean bFromProxy, Boolean useLongPath, Boolean checkHost)
at System.IO.FileStream..ctor(String path, FileMode mode, FileAccess access, FileShare share, Int32 bufferSize)
at XiaoMiFlash.code.Utility.Log.w(String msg, Boolean throwEx)
at XiaoMiFlash.code.Utility.Log.w(String msg)
at XiaoMiFlash.MainFrm.RefreshDevice()
at XiaoMiFlash.MainFrm.btnRefresh_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4515.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/Windows/Microsoft.NET/Framework/v4.0.30319/mscorlib.dll
----------------------------------------
XiaoMiFlash
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Users/n/Desktop/folder/MiFlash20181115/XiaoMiFlash.exe
----------------------------------------
System.Windows.Forms
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4550.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Windows.Forms/v4.0_4.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4536.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System/v4.0_4.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
System.Drawing
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4395.0 built by: NET48REL1LAST_B
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Drawing/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
MiUSB
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Users/n/Desktop/folder/MiFlash20181115/MiUSB.DLL
----------------------------------------
System.Management
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4435.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Management/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Management.dll
----------------------------------------
System.Configuration
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4341.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Configuration/v4.0_4.0.0.0__b03f5f7f11d50a3a/System.Configuration.dll
----------------------------------------
System.Core
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4536.0 built by: NET48REL1LAST_C
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Core/v4.0_4.0.0.0__b77a5c561934e089/System.Core.dll
----------------------------------------
System.Xml
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4161.0 built by: NET48REL1
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/System.Xml/v4.0_4.0.0.0__b77a5c561934e089/System.Xml.dll
----------------------------------------
Accessibility
Assembly Version: 4.0.0.0
Win32 Version: 4.8.4161.0 built by: NET48REL1
CodeBase: file:///C:/WINDOWS/Microsoft.Net/assembly/GAC_MSIL/Accessibility/v4.0_4.0.0.0__b03f5f7f11d50a3a/Accessibility.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.
Any tips on how to recover this situation

If you have a black screen it looks you only can use EDL (testpoint) mode to recover the phone.
In that case you problably need an engineering rom or patched firehose file to pass the Mi authentication.
Maybe a modded Miflash tool without authentification could work too.
​
(For Poco M3 there is a description how you can do this)

I cannot strip open my phone its only a month old.
Elinx said:
If you have a black screen it looks you only can use EDL (testpoint) mode to recover the phone.
In that case you problably need an engineering rom or patched firehose file to pass the Mi authentication.
Maybe a modded Miflash tool without authentification could work too.
​
(For Poco M3 there is a description how you can do this)
Click to expand...
Click to collapse
I cannot strip open my phone its only a month old.

Unambiguous said:
I cannot strip open my phone its only a month old.
Click to expand...
Click to collapse
Then only you can contact the seller or Xiaomi service center

Unambiguous said:
I cannot strip open my phone its only a month old.
I cannot strip open my phone its only a month old.
Click to expand...
Click to collapse
Surely you can get to EDL mode without opening phone, there is a few ways. Have you tried reinstalling with miflash, relocking bootloader?, are you saying that your pc is not detecting the device at all.

Unambiguous said:
I cannot strip open my phone its only a month old.
Click to expand...
Click to collapse
You also can try first, very long power press. Without or with charger connected.
Sometimes this resolve the blackscreen problem.

Very frustrating. I don’t know what mode or state the phone is in. But it makes a noise usb noise when connected. Can’t detect in miflash
Will try another pc. If anyone is Will to join a zoom call to help
Am open to that too

gazza35 said:
Surely you can get to EDL mode without opening phone, there is a few ways. Have you tried reinstalling with miflash, relocking bootloader?, are you saying that your pc is not detecting the device at all.
Click to expand...
Click to collapse
Very frustrating. I don’t know what mode or state the phone is in. But it makes a noise usb noise when connected. Can’t detect in miflash
Will try another pc. If anyone is Will to join a zoom call to help
Am open to that too

Unambiguous said:
Very frustrating. I don’t know what mode or state the phone is in. But it makes a noise usb noise when connected. Can’t detect in miflash
Will try another pc. If anyone is Will to join a zoom call to help
Am open to that too
Click to expand...
Click to collapse
Have you just tried the long power button press, hold the power button for about 10 seconds, that should force a reboot, after a few minutes, connect to pc and try miflash again to see if it connects, you could also google XiaomiMiTool v2, that is another way of bypassing Xiaomi authorisations, has lots of useful tools to unlock \ Lock BL, flash etc, that may work for you, just need to get windows to detect the phone.
XiaoMiTool V2 Easy installation tool – Xiaomi Tools
xiaomitools.com

But overall the bad news is, the black screen of death as its known, usually requires a service at an outhorised repair shop, problem is youd probably have to pay, but i really dont think the charge would be too much, once repaired, i wouldnt mess with it again, id keep it stock.

gazza35 said:
But overall the bad news is, the black screen of death as its known, usually requires a service at an outhorised repair shop, problem is youd probably have to pay, but i really dont think the charge would be too much, once repaired, i wouldnt mess with it again, id keep it stock.
Click to expand...
Click to collapse
Ok thanks will have a look or send it for service
Phone only shows up on windows device manager not ADB list

I opened a service request via xiaomi uk and they are sending a jiffy bag. If they dont fix ill consider.
thanks for sharing. Am still miffed why i cant fix it myself.

Unambiguous said:
I opened a service request via xiaomi uk and they are sending a jiffy bag. If they dont fix ill consider.
thanks for sharing. Am still miffed why i cant fix it myself.
Click to expand...
Click to collapse
Glad youre getting it sorted. I know everyone likes to mess, flash, root, mod etc, but the development for this phone is patchy at best, nothing id consider a solid daily driver without issues, (NO disrespect to Devs intended because they work hard on these things for free). But my advice is simple, Unlock bootloader yes, but stick to to Stock Miui, whatever version you want to be on, at least ya guaranteed to still have a warranty and not worry about problems with bugs. Its a shame, but always issues with china phones, my previous was a Huawei, development again on that was really poor and you had to pay to unlock the bootloader. If youre looking for a phone you can constantly flash or mod then id suggest switch to a Samsung, me, im happy with Miui, especially for the macro camera and 4k video, its very good.

gazza35 said:
Glad youre getting it sorted. I know everyone likes to mess, flash, root, mod etc, but the development for this phone is patchy at best, nothing id consider a solid daily driver without issues, (NO disrespect to Devs intended because they work hard on these things for free). But my advice is simple, Unlock bootloader yes, but stick to to Stock Miui, whatever version you want to be on, at least ya guaranteed to still have a warranty and not worry about problems with bugs. Its a shame, but always issues with china phones, my previous was a Huawei, development again on that was really poor and you had to pay to unlock the bootloader. If youre looking for a phone you can constantly flash or mod then id suggest switch to a Samsung, me, im happy with Miui, especially for the macro camera and 4k video, its very good.
Click to expand...
Click to collapse
this will be my mums new phone...so good advise indeed.