Database Develop

Runnning the unlocker step-by-step

This excruciating step-by-step might help someone...
Wherever I mention establishing a WMDC/AS connection, make damn well sure that the connection is established... If you don't, you won't kill your device, but you won't unlock either.
-Establish a WMDC(Vista) or Activeysnc connection(XP)
-Confirm this!
-Start the unlocker program on your PC.
-Click "Flash SPL" (Step 1)
-Click "Yes"
-On the Treo you are prompted to allow the install of itsutils.dll and jumpspl.exe. Say YES to both.
*****The Treo will reboot. Don't click anything on the PC until the treo is back up and a WMDC/AS connection is re-established
-On your PC, you will see "Cheetah RUU". Click Next.
-Click Next again
-Click Next
-Click Update
-Click Next
-Click Next
******The Treo will reboot into bootloader mode and flashing begins. The device will reboot after the flash completes. Don't click anything on the PC until the Treo is back up and a WMDC/AS connection is re-established
-Click finish
-Click "Unlock Radio" (Step 2)
-Click Next
-Click Next
-Click next
-Click Update
-Click Next
-Click Next
******The Treo will reboot into bootloader mode and flashing begins. The device will reboot after the flash completes. Don't click anything on the PC until the Treo is back up and a WMDC/AS connection is re-established
-Click Finish
-On the PC is a notice "Read this through!". Confirm that you have a good WMDC/AS connection.
-Click OK
-On the Treo click "Yes" to allow athena unlock.exe
-On the Treo follow the instructions - check off SIM and CID unlock
-On the Treo click "Unlock" and wait for it to finish, then click OK on the athena unlocker on the Treo, and then click OK on the Treo to close the athena unlocker.
-On the PC, click OK
-Ensure you still have a WMDC/AS connection.
-On the PC, click "Flash normal radio" (Step 3)
proceed through the series of "Next", the device will go into bootloader mode and flash one more time. The device will reboot when done, and you should be all set.

Hey Summiter. Thanks for your tutorial. Got one question. I've done the whole process and now my SPL-says 1.40.01 OliNex. So I'am assumming that all went well. The only thing that gets me is that in you guide you state that this process will hard reset my device and all info. will be lost. My information as well as my programs all remained intacked. Is this OK. or am I missing something.
Thanks.

My bad..it won't do a hard reset. My device hard reset when I was running a different process, not the released unlocker. =) Sorry to cause concern.
As for the slow 3G speeds, Olipro is looking into it.
manfly9884 said:
Hey Summiter. Thanks for your tutorial. Got one question. I've done the whole process and now my SPL-says 1.40.01 OliNex. So I'am assumming that all went well. The only thing that gets me is that in you guide you state that this process will hard reset my device and all info. will be lost. My information as well as my programs all remained intacked. Is this OK. or am I missing something.
Thanks.
Click to expand...
Click to collapse

summiter said:
My bad..it won't do a hard reset. My device hard reset when I was running a different process, not the released unlocker. =) Sorry to cause concern.
As for the slow 3G speeds, Olipro is looking into it.
Click to expand...
Click to collapse
Thanks for your quick response.

Can anyone check Radio Ver after last step
Can someone verify the Radio Ver after 3rd step (Normal Radio Flashed Back to Device) , Olipro said to my post that by having Radio at 1.16 , i didnt complete last (3) step , but i defenatly did , and my Radio still 1.16 , where i had 1.52 before unlocking ???????????????????
Hitec

I called cingular tonight because i have been trying to get my 750 paired with my tom tom one 3rd edition for use of the weather updates and cameras and such. Through conversation with a support representative, and trying to troubleshoot why it couldn't use the wireless connection of the phone, the representative asked me to check a few things on my phone. While answering some questions, one of which was about device software and such and i told him i had windows mobile 6 installed.
From this point on he led into reasons why i should be using it with out it being released and such which is to be expected. He also stated that doing to much to the phone can possibly make the phone upgradable when the real WM6 update is released. This he mentioned were changing the boot loader, IPL and SPL software in the phone, that and using bogus releases of software. The reason being he said was that the soon to be released update probes the phone deeply because everything has been updated including the boot loader stuff.
Now i cant confirm or deny any truth to these statements but the only thing i had done with mine was a try a few new firmwares but after my conversation with them i quickly reverted back to WM5.

jhowle said:
From this point on he led into reasons why i should be using it with out it being released and such which is to be expected. He also stated that doing to much to the phone can possibly make the phone upgradable when the real WM6 update is released. This he mentioned were changing the boot loader, IPL and SPL software in the phone, that and using bogus releases of software. The reason being he said was that the soon to be released update probes the phone deeply because everything has been updated including the boot loader stuff.
Click to expand...
Click to collapse
F.U.D.
That's utter ****ing bull****, the RUU will do no such ****ing thing, and even if it does, there'll still be a base NBH to dump and flash... complete crap.
the bootloader might well have been updated, but the Hard-SPL one on there isnt going to let it overwrite it, mate.

jst passing on the info dude,, don't blame me.. they said it

mines unlocked anyway, but i did a remote unlock with GSM libeerty.com only cocts 39 bux and it does work. i figured if i spent 39 bux and avoided the potential of bricking my treo than it is worth it.

jhowle said:
mines unlocked anyway, but i did a remote unlock with GSM libeerty.com only cocts 39 bux and it does work. i figured if i spent 39 bux and avoided the potential of bricking my treo than it is worth it.
Click to expand...
Click to collapse
well not really, but you paid your money and took your choice

i guess i just see how the HARD SPL really does any different besides bypass the lock function. I have tried some very similar programz with my black berries and even after they said they were unlocked you could still goto the SIM CARD Screen under advanced options and hold ALT and press M - E - P - 2 and walla the code entry screen window would still come up.

after completing step 2, I don't even have the option to install athena unlock.exe ?
Also, it gives me an error after I click "Read this through"
What's going on?
Am I doing something wrong?
EDIT:
itsutils.dll didn't even install
During step 1, jumpspl and enterbootloader are installed, NOT ITSUTILS
Any help is appreciated

Why no flash?
I just tried running the unlocker. I have an AT&T branded and locked Treo 750 with Windows Mobile 6. When I run the unlocker, it installed itsutils.dll the first time, but the freeze that i am supposed to look for never occured. Then it installs the jumpspl.exe, and restarts. Then i wait until the ActiveSync is reconnected, and run the RUU. The RUU says that it fails flashing either radio (the patched one or the stock one) after 7%, and gives me an error. But then the unlocker application ran on the phone, and said it was successfully unlocked. I check the SPL version and there is nothing about 1.40 OliNex. Is there a step that I am obviously missing? I thought i had to CID unlock it first, but it gives me the option to CID unlock and it says it is unnecessary on the unlocker itself. Im sorry for being such a bonehead, but any suggestions? Thanks.

just goto www.gsmliberty.com it onlu cocts 39.99 for a remote unlock and there is no risk of bricking ur phone

unhandled exception error
Treo 750 with AT&T running WM5 trying to unlock to use on another GSM carrier. Downloaded the current treo 750 unlock software from this site. after step 2 I get unhandled exception error and cannot continue. Phone is synced properly and I have followed all steps to the "t".
I see this question asked many times throughout the site but never an answer. can someone let me know what causes it and how to fix it. I know lots of people would appreciate it.
Thanks in advance for your time.

JBoever said:
Treo 750 with AT&T running WM5 trying to unlock to use on another GSM carrier. Downloaded the current treo 750 unlock software from this site. after step 2 I get unhandled exception error and cannot continue. Phone is synced properly and I have followed all steps to the "t".
I see this question asked many times throughout the site but never an answer. can someone let me know what causes it and how to fix it. I know lots of people would appreciate it.
Thanks in advance for your time.
Click to expand...
Click to collapse
I think I manually copied the Athenaunlock.exe to the phone and ran it at that step. Note - this was after the special "unlock" radio had already been flashed. Finally, I did a hard reset and then installed a new OS - ROW 2.23 which previously would not load on phone (because it was locked).
I hope this helps.

unlock not working. unhandled exception
I get the following error after I finish the radio patch and it trys to run athen unlock.exe
Unhandled exception has occurred in your application. If you lcick continue, the application will ignore this erro and attempt to continue. If you click Quit. The appication will close immediately. (below are the details)
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.ComponentModel.Win32Exception: The system cannot find the file specified
at System.Diagnostics.Process.StartWithCreateProcess(ProcessStartInfo startInfo)
at System.Diagnostics.Process.Start()
at AthenaUnlocker.Form1.runExecutable(String path, String args, String wdir)
at AthenaUnlocker.Form1.button2_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/Microsoft.NET/Framework/v2.0.50727/mscorlib.dll
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System/2.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
zip
Assembly Version: 0.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System.Windows.Forms
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Windows.Forms/2.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Drawing/2.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.

Same issue
Am currently trying to run from the SD card after updating .NET. Keep you posted

Can't get past the .NET error despite reloading latest version of .NET
Suggestions anyone?

alerner1 said:
I get the following error after I finish the radio patch and it trys to run athen unlock.exe
Unhandled exception has occurred in your application. If you lcick continue, the application will ignore this erro and attempt to continue. If you click Quit. The appication will close immediately. (below are the details)
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.ComponentModel.Win32Exception: The system cannot find the file specified
at System.Diagnostics.Process.StartWithCreateProcess(ProcessStartInfo startInfo)
at System.Diagnostics.Process.Start()
at AthenaUnlocker.Form1.runExecutable(String path, String args, String wdir)
at AthenaUnlocker.Form1.button2_Click(Object sender, EventArgs e)
at System.Windows.Forms.Control.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnClick(EventArgs e)
at System.Windows.Forms.Button.OnMouseUp(MouseEventArgs mevent)
at System.Windows.Forms.Control.WmMouseUp(Message& m, MouseButtons button, Int32 clicks)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ButtonBase.WndProc(Message& m)
at System.Windows.Forms.Button.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/Microsoft.NET/Framework/v2.0.50727/mscorlib.dll
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System/2.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
zip
Assembly Version: 0.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
AthenaUnlocker
Assembly Version: 1.0.0.0
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Documents%20and%20Settings/user/Desktop/CheetahUnlocker.exe
----------------------------------------
System.Windows.Forms
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Windows.Forms/2.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.832 (QFE.050727-8300)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Drawing/2.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.
Click to expand...
Click to collapse
And NOW?????????

some 1 plz help me with rom upgrading

i used to upgrade rom before but i dont kno wat happn suddenly lik my system shows error
popping a window statin MICROSOFT WINDOWS DIAMOND CUSTOM RUU HAS STOPPED WORKING i am usin vista ultimate the problem details are like this
Problem signature:
Problem Event Name: APPCRASH
Application Name: CustomRUU.exe
Application Version: 1.0.0.0
Application Timestamp: 483f28db
Fault Module Name: ntdll.dll
Fault Module Version: 6.0.6000.16386
Fault Module Timestamp: 4549bdc9
Exception Code: c000007b
Exception Offset: 00008fc7
OS Version: 6.0.6000.2.0.0.256.1
Locale ID: 1033
Additional Information 1: 9d13
Additional Information 2: 1abee00edb3fc1158f9ad6f44f0f6be8
Additional Information 3: 9d13
Additional Information 4: 1abee00edb3fc1158f9ad6f44f0f6be8

The best solution is to try it on WinXP. I had some crashes with the hardspl with a Vista PC. If you dont want to install it, try a Virtual Machine.

marco.it said:
The best solution is to try it on WinXP. I had some crashes with the hardspl with a Vista PC. If you dont want to install it, try a Virtual Machine.
Click to expand...
Click to collapse
thnx for the reply wat do u mean by virtual machine?

try using the internal storage method or updating your ROM.

Installing from Internal Storage is the fastest and safest way to upgrade ROM.
1) Rename the ROM to DIAMIMG.nbh and copy into your internal storage
2) While pressing VolDown and Back, use your stylus to press the reset button
3) After a few seconds, it will ask you whether you want to proceed to install ROM from Internal Storage.
However, every ROM cooker recommends some type of HardSPL. You must make sure that you meet the requirement, lest you brick your TD.

HardSPL stopped working? Help!

Ok, so I tried using hardSPL, and I keep getting an error message as soon as I launch the program saying that it stopped working. Im using windows 7 premium home edition. I read through the forum on HardSPL, and nothing fixed this problem. No antivirus software was running, or firewalls. Does anyone have any advice? Anything at all would be very much appreciated....

I followed this to the T and had no issues using windows 7. I noticed you stated you read through the HardSpl forum but did not see if you attempted to use this guide. Based on a few assumptions, on the forum you posted in, hopefully this helps.
http://forum.xda-developers.com/showpost.php?p=5084595&postcount=1132

shiftylock said:
Ok, so I tried using hardSPL, and I keep getting an error message as soon as I launch the program saying that it stopped working. Im using windows 7 premium home edition. I read through the forum on HardSPL, and nothing fixed this problem. No antivirus software was running, or firewalls. Does anyone have any advice? Anything at all would be very much appreciated....
Click to expand...
Click to collapse
Hm... that's very strange. I'm also running on Windows 7 and I had no problems at all. Are you sure literally everything was turned off? I know my computer came with McAfee for free and it was being TOO good. I had to go into it and disable every little thing to get it to work. Maybe try that and see what happens... security programs always give a big fuss with this. Also, make sure you have the enablerapinew.cab installed on your phone, it doesnt say that in some of the walkthroughs.

Im positive everything is turned off. The second I try to open the program, it says it stopped working. I don't see any menus or anything. When I clicked the "additional details" box, here's what came up
Problem Event Name: BEX
Application Name: Rhodium-HardSPL_V2_00R3.exe
Application Version: 0.0.0.0
Application Timestamp: 21000000
Fault Module Name: Rhodium-HardSPL_V2_00R3.exe
Fault Module Version: 0.0.0.0
Fault Module Timestamp: 21000000
Exception Offset: 000000c4
Exception Code: c0000005
Exception Data: 00000008
OS Version: 6.1.7600.2.0.0.768.3
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789

did you try running it as an Administrator? if not try downloading it again on a different computer or try the Old HardSPL good luck

Please post in the existing thread rather than creating a new one.
Thanks
Dave

Fallout New Vegas crashes on launch, Win7 Ultimate x64

So I installed Fallout NV on my PC, but right after a few seconds of game launch, it crashes.
I have a Windows 7 Ultimate x64, and my hardware is:
Asus P5QC Motherboard - Intel Core2Duo E7300 - ATI Radeon 4850 (with latest x64 driver) - and 4 GB's of DDR2 RAM.
I've tried many of common fixes on the web, like Win XP compatibility mode, copying some DLL file... nothing worked.
Here's the problem detail on crash dialog:
Code:
Problem Event Name: APPCRASH
Application Name: FalloutNV.exe
Application Version: 1.0.0.240
Application Timestamp: 4c9808f2
Fault Module Name: FalloutNV.exe
Fault Module Version: 1.0.0.240
Fault Module Timestamp: 4c9808f2
Exception Code: c0000005
Exception Offset: 006002a5
OS Version: 6.1.7601.2.1.0.256.1
Locale ID: 2057
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789
On Sevenforums somebody suggested to update DirectX. And this happened:
At first it said Installed successfully. But Windows asked if the program was installed correctly. I chose to re-install using recommended settings and the installation crashed. Here's the log:

Nokia OST couldnt run... pops microsoft .net framework error!

Hello,
i tried to launch OST but popping error... i dnt know why its like dat and i have searched online for help but none gotten yet. i have attached screenshots of the error here too!
i have windows 10 pro/64bits. i need help please!
thanks...

whalesplaho said:
Hello,
i tried to launch OST but popping error... i dnt know why its like dat and i have searched online for help but none gotten yet. i have attached screenshots of the error here too!
i have windows 10 pro/64bits. i need help please!
thanks...
Click to expand...
Click to collapse
Could you post all text information about the details of the error? (Right click, select all, copy)
Are you running the tool with administrative elevation?

dbpm1 said:
Could you post all text information about the details of the error? (Right click, select all, copy)
Are you running the tool with administrative elevation?
Click to expand...
Click to collapse
here is tha error code..... thanks big!
Im running the tool without administrative elevation.
I have net framework v4.7 installed.
Code:
See the end of this message for details on invoking
just-in-time (JIT) debugging instead of this dialog box.
************** Exception Text **************
System.NullReferenceException: Object reference not set to an instance of an object.
at MainForms.Form1.DisableOptions()
at MainForms.Form1.Form1_Load(Object sender, EventArgs e)
at System.Windows.Forms.Form.OnLoad(EventArgs e)
at System.Windows.Forms.Form.OnCreateControl()
at System.Windows.Forms.Control.CreateControl(Boolean fIgnoreVisible)
at System.Windows.Forms.Control.CreateControl()
at System.Windows.Forms.Control.WmShowWindow(Message& m)
at System.Windows.Forms.Control.WndProc(Message& m)
at System.Windows.Forms.ScrollableControl.WndProc(Message& m)
at System.Windows.Forms.ContainerControl.WndProc(Message& m)
at System.Windows.Forms.Form.WmShowWindow(Message& m)
at System.Windows.Forms.Form.WndProc(Message& m)
at MainForms.Form1.WndProc(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.OnMessage(Message& m)
at System.Windows.Forms.Control.ControlNativeWindow.WndProc(Message& m)
at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam)
************** Loaded Assemblies **************
mscorlib
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/Windows/Microsoft.NET/Framework/v2.0.50727/mscorlib.dll
----------------------------------------
OnlineUpdateTool
Assembly Version: 6.0.4.0
Win32 Version: 6.0.4
CodeBase: file:///C:/Program%20Files%20(x86)/OST%20LA/OnlineUpdateTool.exe
----------------------------------------
System
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System/2.0.0.0__b77a5c561934e089/System.dll
----------------------------------------
System.Configuration
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Configuration/2.0.0.0__b03f5f7f11d50a3a/System.Configuration.dll
----------------------------------------
System.Xml
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Xml/2.0.0.0__b77a5c561934e089/System.Xml.dll
----------------------------------------
System.Windows.Forms
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Windows.Forms/2.0.0.0__b77a5c561934e089/System.Windows.Forms.dll
----------------------------------------
System.Drawing
Assembly Version: 2.0.0.0
Win32 Version: 2.0.50727.8922 (WinRelRS4.050727-8900)
CodeBase: file:///C:/WINDOWS/assembly/GAC_MSIL/System.Drawing/2.0.0.0__b03f5f7f11d50a3a/System.Drawing.dll
----------------------------------------
MRG.Controls.UI
Assembly Version: 1.0.4854.21889
Win32 Version: 1.0.0.0
CodeBase: file:///C:/Program%20Files%20(x86)/OST%20LA/MRG.Controls.UI.DLL
----------------------------------------
************** JIT Debugging **************
To enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.

@bidhata @hikari_calyx @dbpm1 and others please help..... Thanks!!!

whalesplaho said:
System.NullReferenceException: Object reference not set to an instance of an object.
Click to expand...
Click to collapse
@whalesplaho I could not reproduce the error on two computers which i have tested.. but from what I could gather information about the error referenced above, there may be a problem with your .net install.
I've found two utilities that may help you fix the issue, but they should only point to problems on the .net installation, not directly solve them! You may run them just to have information on which version is crippled and then you should uninstall and install again.
Raymondcc .NET Detector
One way to check which versions of .NET are installed is through the system registry. If a .NET package is installed, its information should be correctly entered in the registry. We decided to use this method and create a little tool which does the plain and simple task of telling you which versions of .NET you have installed.
The tool couldn’t be simpler to use, just run the executable and it will tell you which .NET’s you have by showing them in dark text, the grayed out entries aren’t installed. Clicking on a non installed package will take you to its download page at Microsoft. The information from the window is copied to the clipboard to paste into help files etc. The program is able to detect .NET Frameworks from 1.0 up to the latest 4.7.2 (including versions specific to Windows 10), is portable and works on Windows XP and above.
Read More: https://www.raymond.cc/blog/how-to-...osoft-net-framework-is-installed-in-computer/
Download: https://www.raymond.cc/blog/download/did/1741/
Click to expand...
Click to collapse
.NET Framework Setup Verification Utility.
The .NET Framework Setup Verification Utility by Aaron Stebner is a very small and portable tool at only 272KB in size that you can use to verify the presence of files, directories, registry keys and values for the .NET Framework that is installed in your Windows computer. The latest version of .NET Framework Setup Verification Utility is able to automatically perform a set of steps to verify the installation state of the following .NET Frameworks:
.NET Framework 1.0
.NET Framework 1.1
.NET Framework 1.1 SP1
.NET Framework 2.0
.NET Framework 2.0 SP1
.NET Framework 2.0 SP2
.NET Framework 3.0
.NET Framework 3.0 SP1
.NET Framework 3.0 SP2
.NET Framework 3.5
.NET Framework 3.5 SP1
.NET Framework 4 Client
.NET Framework 4 Full
.NET Framework 4.5
Only the .NET Framework that the utility detects on the computer will be listed for verification so you won’t be seeing all of the above versions of the .NET Framework on the program. To verify the install state of a .NET Framework, simply select the version at the drop down box and click the Verify Now button. If the current status shows “Product verification succeeded”, then it means no problem but if you get a failed message, then you can consider reinstalling the .NET Framework version that has failed the verification.
Read More: https://www.raymond.cc/blog/net-framework-setup-verification-utility/
Download: https://www.raymond.cc/blog/download/did/2148/
Click to expand...
Click to collapse
If you have problems uninstalling or repairing, follow the tips here: https://www.raymond.cc/blog/uninstall-microsoft-net-framework-with-aaron-stebner-cleanup-tool/
Remember to reply if the issue was solved or not for future reference:good:
Good luck mate!

Tried everything and other method but no luck... I installed on a friends Windows 7 Ultimate and works very well!!!
Really don't know why its not working on my laptop... Really frustrating!!!

whalesplaho said:
Tried everything and other method but no luck... I installed on a friends Windows 7 Ultimate and works very well!!!
Really don't know why its not working on my laptop... Really frustrating!!!
Click to expand...
Click to collapse
That's really bad man, there must be something wrecked with .net on that laptop!
Can you run other .net dependant apps? Like Paint.net for example: https://www.getpaint.net/

dbpm1 said:
That's really bad man, there must be something wrecked with .net on that laptop!
Can you run other .net dependant apps? Like Paint.net for example: https://www.getpaint.net/
Click to expand...
Click to collapse
I have net framework working on my laptop... I have Paint.net app

Same problem here

V1c70rs said:
Same problem here
Click to expand...
Click to collapse
Had to reformat my laptop...

whalesplaho said:
Had to reformat my laptop...
Click to expand...
Click to collapse
Reformatting isn't a proper solution. Anyways, the error changed into "Culture id 3072 isn't a supported culture" when i updated OST LA to 6.37. After googling a bit, found out culture problem is related to Region and Language of Windows 10. So changed Region and Language to United States English even though I am not in USA. That got rid of the Culture problem and OST 6.37 started up fine but this version needs needed id and password. So uninstalled it, installed 6.04 version and it started up fine.
So, in short, the Solution is;
Change Region and Language to United States and United States English respectively.

This
Mist978 said:
Reformatting isn't a proper solution. Anyways, the error changed into "Culture id 3072 isn't a supported culture" when i updated OST LA to 6.37. After googling a bit, found out culture problem is related to Region and Language of Windows 10. So changed Region and Language to United States English even though I am not in USA. That got rid of the Culture problem and OST 6.37 started up fine but this version needs needed id and password. So uninstalled it, installed 6.04 version and it started up fine.
So, in short, the Solution is;
Change Region and Language to United States and United States English respectively.
Click to expand...
Click to collapse
This was the solution for me. Had been tearing my hair out because of this error. Just changed my region and boom! Thank you!

Mist978 said:
Reformatting isn't a proper solution. Anyways, the error changed into "Culture id 3072 isn't a supported culture" when i updated OST LA to 6.37. After googling a bit, found out culture problem is related to Region and Language of Windows 10. So changed Region and Language to United States English even though I am not in USA. That got rid of the Culture problem and OST 6.37 started up fine but this version needs needed id and password. So uninstalled it, installed 6.04 version and it started up fine.
So, in short, the Solution is;
Change Region and Language to United States and United States English respectively.
version 6.1.2 solved it for me.
Click to expand...
Click to collapse