Database Develop

...

...

I hope u find this, i've also a bricked x+1

If anyone have this tool I need too!!
Thanks

Can you get into bootloader mode? Charge the phone and see if you can get into bootloader mode.

I'm on the same boat... Just got my Moto X 2014 bricked... Found the tool and files for the original Moto X, but not for Moto X 2014. I don't think they exist (yet).
---------- Post added at 05:08 PM ---------- Previous post was at 05:03 PM ----------
@JulesJam
I am (and I believe eveybody else on this post is) requesting the tool / files because our smartphones are bricked in a way we can't access the bootloader. The tool Junior asked on the OP is to repair / reflash the bootloader, which probably got corrupt, so there's no way to access it and flash anything through Fastboot.
---------- Post added at 05:11 PM ---------- Previous post was at 05:08 PM ----------

joker2mbr said:
I am (and I believe eveybody else on this post is) requesting the tool / files because our smartphones are bricked in a way we can't access the bootloader. The tool Junior asked on the OP is to repair / reflash the bootloader, which probably got corrupt, so there's no way to access it and flash anything through Fastboot.
Click to expand...
Click to collapse
Ok, yes, if you corrupted the bootloader than you obviously can't get into bootloader mode. But a lot of times people just don't know how to get into bootloader mode when they have a blank screen. So I was asking.
If your screen is blank when you turn on your device and you know the phone is charged, you can press and hold the power button for about 5 seconds, then immediately press and hold volume down and then press and hold power again and hold both for about 4 seconds then release. I have found I need to press and hold both volume up/down then while still holding press power and keep all 3 held down for 4 seconds and then release. I don't know why but pressing and holding all 3 seems to work better for me.

JulesJam said:
Can you get into bootloader mode? Charge the phone and see if you can get into bootloader mode.
Click to expand...
Click to collapse
The screen is only black and phone doesn't get to the fastboot. I've tried a number of ways.
When I connect to the PC, the device is recognized with the name QHSUSB_DLOAD.
When I connect to the charger, the green led flashes constantly.

Ive already have the .hex files

Junior Passos said:
The screen is only black and phone doesn't get to the fastboot. I've tried a number of ways.
When I connect to the PC, the device is recognized with the name QHSUSB_DLOAD.
When I connect to the charger, the green led flashes constantly.
Click to expand...
Click to collapse
The behavior I see here is quite the same. I tried to use the blankflash tool, but as you already discovered, it needs some device specific files (from the bootloader) and the ones available around just won't work with the Moto X 2014... Install the unsigned device driver on Windows is not difficult. The problem is to find these files, that should come directly from Motorola. Without them, we can't restore the bootloader, that is probably corrupted.
---------- Post added at 11:26 PM ---------- Previous post was at 11:22 PM ----------
dashiell_cano said:
Ive already have the .hex files
Click to expand...
Click to collapse
Did you manage to use the files you've found to fix your bootloader? I thought the needed files were like "singleimage_XXXX.bin"... Please let us know your results.
Thanks a lot!

Junior Passos said:
The screen is only black and phone doesn't get to the fastboot. I've tried a number of ways.
When I connect to the PC, the device is recognized with the name QHSUSB_DLOAD.
When I connect to the charger, the green led flashes constantly.
Click to expand...
Click to collapse
Has anyone looked at this process to see if some variation of it can be used to resurrect your device?
http://forum.xda-developers.com/moto-x/general/moto-x-root-pogress-60-t3071602
I am not familiar with the process used here to resurrect a bricked Moto X 2013:
http://forum.xda-developers.com/moto-x/general/how-to-resurrecting-bricked-moto-x-t2629057
However, I have a file emmc_appsboot.mbn for 5.0 for XT1096 (Verizon Moto X 2014) and from scanning the thread above, that may be a useful file.

I can access to the command system, but with the .bin file ive found i receive the "file to large" or "wrong version" message sometimes.
As you said we need the right .bin file.

dashiell_cano said:
I can access to the command system, but with the .bin file ive found i receive the "file to large" or "wrong version" message sometimes.
As you said we need the right .bin file.
Click to expand...
Click to collapse
do you know what emmc_appsboot.mbn is?

JulesJam said:
do you know what emmc_appsboot.mbn is?
Click to expand...
Click to collapse
As i know the mbn file Is the equivalent to the .hex file, am i wrong?

dashiell_cano said:
As i know the mbn file Is the equivalent to the .hex file, am i wrong?
Click to expand...
Click to collapse
Idk, but I have that file and it is for the aboot partition if anyone wants it I can upload it. But it is for the XT1096, I don't know if that matters or not. Do you want it?

Yes please, with your file, mine and the next files to come maybe together we can solve this puzzle

dashiell_cano said:
Yes please, with your file, mine and the next files to come maybe together we can solve this puzzle
Click to expand...
Click to collapse
https://www.dropbox.com/s/5bu79og4b3oqbug/emmc_appsboot.mbn?dl=0
---------- Post added at 05:07 AM ---------- Previous post was at 05:03 AM ----------
dashiell_cano said:
Yes please, with your file, mine and the next files to come maybe together we can solve this puzzle
Click to expand...
Click to collapse
Also read this:
http://forum.xda-developers.com/showpost.php?p=60635306&postcount=431
What is the emmc software flasher tool? Is it this?
http://androidxda.com/download-emmc-dl-tool

JulesJam said:
https://www.dropbox.com/s/5bu79og4b3oqbug/emmc_appsboot.mbn?dl=0
---------- Post added at 05:07 AM ---------- Previous post was at 05:03 AM ----------
Also read this:
http://forum.xda-developers.com/showpost.php?p=60635306&postcount=431
What is the emmc software flasher tool? Is it this?
http://androidxda.com/download-emmc-dl-tool
Click to expand...
Click to collapse
The flasher tool is a program that let you solve the missing recovery with the qualcomm devices instead of use command lines(its something like rsd vs mfastboot), you need 2 files, .hex file ( or mbn) and .bin file (the emergency recovery). You have the mbn (same as my .hex) we just need the .bin one.

dashiell_cano said:
The flasher tool is a program that let you solve the missing recovery with the qualcomm devices instead of use command lines(its something like rsd vs mfastboot), you need 2 files, .hex file ( or mbn) and .bin file (the emergency recovery). You have the mbn (same as my .hex) we just need the .bin one.
Click to expand...
Click to collapse
Is the .bin file something I can pull from a working device? Or is it inaccessible?

... I really dont know

dashiell_cano said:
... I really dont know
Click to expand...
Click to collapse
The Droid Ultra is very similar to the Moto X 2014, do you think any of these files may work?
http://forum.xda-developers.com/droid-ultra/general/droid-ultra-maxx-brick-recovery-t2830806
maybe this:
MPRG8960_MOTO.zip

Help unbrick my P9

Hello everyone,
I tried to install a OTA update to nougat using SD system local update.
in 98% it's show error and loop in recovery...
i tried to install stock rom using fastboot get error..
using press (VOL+)+(VOL-) to enter update from SD and no success
my bootloader locked.
spec:
Found Phone : EVA-L09
IMEI : 869827028453054
Serial NR. : MWS0216719004568
Firmware : EVA-L09C671B150
Please if any one can help me bring back to life my p9.
sorry for my English.

There are several guides here how to get your P9 working again from such a state. Which have you tried?
Especially this is short and to the point: https://forum.xda-developers.com/showpost.php?p=71195544&postcount=4
Please be more verbose as to what you have done and which error messages and behaviour you see. That will enable others to understand what might be happening and how to help you.

tbr23 said:
There are several guides here how to get your P9 working again from such a state. Which have you tried?
Especially this is short and to the point: https://forum.xda-developers.com/showpost.php?p=71195544&postcount=4
Please be more verbose as to what you have done and which error messages and behaviour you see. That will enable others to understand what might be happening and how to help you.
Click to expand...
Click to collapse
always i have
FAILED (remote: Command not allowed) error message.

can you help me find the stock full firmware for my model?
this is my firmware now EVA-L09C671B150.

UP

Hi
I was in same situation, can't go to recovery, boot non stop on Huawei logo and I save my phone with DC Phoenix. You have to pay 15€ but that work perfectly
https://www.dc-unlocker.com/DC-Phoenix-flash-repair-tutorial

Phiver13 said:
Hi
I was in same situation, can't go to recovery, boot non stop on Huawei logo and I save my phone with DC Phoenix. You have to pay 15€ but that work perfectly
https://www.dc-unlocker.com/DC-Phoenix-flash-repair-tutorial
Click to expand...
Click to collapse
can you help me find Firmware for my p9?

steve19994 said:
can you help me find Firmware for my p9?
Click to expand...
Click to collapse
Easy
Follow the tutorial and don't forget to remove the sd card before starting
https://www.dc-unlocker.com/repair-bricked-huawei-honor-7
Do you have the P9 Eva-l09? If yes, take this one, unzip, put in DC Phoenix
http://www.modaco.com/forums/topic/377249-stock-rom-dload-file-p9-eva-l09-b136/
---------- Post added at 11:52 AM ---------- Previous post was at 11:52 AM ----------
steve19994 said:
can you help me find Firmware for my p9?
Click to expand...
Click to collapse
https://forum.xda-developers.com/p9/how-to/huawei-p9-deleted-t3380098/page3

[TOOL] 6T MsmDownloadTool v4.0.59 (OOS v9.0.13)

This tool can be used to revive a bricked OP6T and remove the 'Device is corrupt' error message on boot.
Contains the latest MsmDownloadTool v4.0.59 and OOS v9.0.13 which is compatible with International and McLaren editions.
OOS v9.0.11 can also be used to convert a T-Mobile model into a fully fledged International model, more info here.
Make sure that your phone is switched off.
Open device manager on your Windows PC.
Press and hold the Volume Up & Volume Down buttons then connect to your PC using your data cable.
Once the device is connected to your Windows PC, check if the phone is being recognized (Other > QUSB_BULK or Ports > Qualcomm).
If showing as Other > QUSB_BULK either wait for Windows to install the Qualcomm driver or download one of the drivers below and install.
Run MsmDownloadTool V4.0 and click Start.
NOTE: This will completely wipe your device and relock your bootloader.
Downloads
6T MsmDownloadTool v4.0.59 (OOS v9.0.13)
6T MsmDownloadTool v4.0.58 (OOS v9.0.12)
6T MsmDownloadTool v4.0.58 (OOS v9.0.11)
6T MsmDownloadTool v4.0.58 (OOS v9.0.6)
6T MsmDownloadTool v4.0.58 (OOS v9.0.5)
Driver
Alternative driver
Shameless plugs - OP referral link for any peops that would like $20/£20/€20 discount: OnePlus or PayPal donation link: PayPal.

Wow nice. Now to test this on T-Mobile!! Let the flashing commence

Don't think this is a good idea; from what has been communicated the Modem for T-Mobile is different or has a different signature; you might end up with a brick. We we obviously won't find out unless we try. The problem is... you don't have an image to re-flash the T-Mobile version, so you might have to send it in.

im tempted to run this today on the tmobile model. how high is the risk of hard brick? will it leave me without fastboot if it doesnt work?
---------- Post added at 07:48 AM ---------- Previous post was at 07:47 AM ----------
dreinulldrei said:
Don't think this is a good idea; from what has been communicated the Modem for T-Mobile is different or has a different signature; you might end up with a brick. We we obviously won't find out unless we try. The problem is... you don't have an image to re-flash the T-Mobile version, so you might have to send it in.
Click to expand...
Click to collapse
apparently the flash to 9.0.5 in the other thread overwrites the modem anyway. its the criticals that dont overwrite. worst case im within my 14 days still, can alwasy return

dreinulldrei said:
Don't think this is a good idea; from what has been communicated the Modem for T-Mobile is different or has a different signature; you might end up with a brick. We we obviously won't find out unless we try. The problem is... you don't have an image to re-flash the T-Mobile version, so you might have to send it in.
Click to expand...
Click to collapse
I thought someone did dump a stock Tmo 9.0 out here?
---------- Post added at 02:20 PM ---------- Previous post was at 02:19 PM ----------
https://androidfilehost.com/?fid=11410963190603845445

SourPower said:
I thought someone did dump a stock Tmo 9.0 out here?
---------- Post added at 02:20 PM ---------- Previous post was at 02:19 PM ----------
https://androidfilehost.com/?fid=11410963190603845445
Click to expand...
Click to collapse
Yep, if a Dev can chime in that I won't be left with a hard brick and will be able to go back to TMobile firm atleastsr I'll jump. The only thing holding me back is that sim unlock and unlock bin. I don't wanna go thru that again if have to exchange.

SourPower said:
I thought someone did dump a stock Tmo 9.0 out here?
---------- Post added at 02:20 PM ---------- Previous post was at 02:19 PM ----------
https://androidfilehost.com/?fid=11410963190603845445
Click to expand...
Click to collapse
It's not how this tool works. A raw dump doesn't equal a flashable fastboot dump doesn't equal a msmdownloadtool ops file.
Edit: apparently you can't use the not equals symbol. I wrote a lengthy reply and it's gone. I'll write a shorter version.
My assumption is there is no version for the T-Mobile, but this will work for a full conversion. OP support will most likely not use this on the T-Mobile version and it's why we had to void our warranty when we unlocked the bootloader. They probably defer you to T-Mobile if you brick your phone. Now that being said, I bet this tool works just fine on the T-Mobile version and will turn it into a full international device capable of OTA updates and everything.
---------- Post added at 02:51 PM ---------- Previous post was at 02:43 PM ----------
strictlyphat said:
Yep, if a Dev can chime in that I won't be left with a hard brick and will be able to go back to TMobile firm atleastsr I'll jump. The only thing holding me back is that sim unlock and unlock bin. I don't wanna go thru that again if have to exchange.
Click to expand...
Click to collapse
One of three things will happen.
One, it will recognize it as the wrong device and won't flash at all.
Two, it will flash and you'll have a hard brick.
Three, it will flash and you'll have a fully converted International version.
If you have to return it to TMobile, you shouldn't have any issues returning it. A dead device is a dead device, the reps don't care. Also getting your new one unlocked should be no issue as all since you already had your first device unlocked. Just tell support that. Your device was unlocked and you had to RMA it. They will SIM unlock no problem. You will still have to wait 7 days for the unlock bin.

hartleyshc said:
It's not how this tool works. A raw dump doesn't equal a flashable fastboot dump doesn't equal a msmdownloadtool ops file.
Edit: apparently you can't use the not equals symbol. I wrote a lengthy reply and it's gone. I'll write a shorter version.
My assumption is there is no version for the T-Mobile, but this will work for a full conversion. OP support will most likely not use this on the T-Mobile version and it's why we had to void our warranty when we unlocked the bootloader. They probably defer you to T-Mobile if you brick your phone. Now that being said, I bet this tool works just fine on the T-Mobile version and will turn it into a full international device capable of OTA updates and everything.
Click to expand...
Click to collapse
Screw it. I'm gonna do this soon. Will report back

hartleyshc said:
It's not how this tool works. A raw dump doesn't equal a flashable fastboot dump doesn't equal a msmdownloadtool ops file.
Edit: apparently you can't use the not equals symbol. I wrote a lengthy reply and it's gone. I'll write a shorter version.
My assumption is there is no version for the T-Mobile, but this will work for a full conversion. OP support will most likely not use this on the T-Mobile version and it's why we had to void our warranty when we unlocked the bootloader. They probably defer you to T-Mobile if you brick your phone. Now that being said, I bet this tool works just fine on the T-Mobile version and will turn it into a full international device capable of OTA updates and everything.
---------- Post added at 02:51 PM ---------- Previous post was at 02:43 PM ----------
One of three things will happen.
One, it will recognize it as the wrong device and won't flash as at.
Two, it will flash and you'll have a hard brick.
Three, it will flash and you'll have a fully converted International version.
If you have to return it to TMobile, you shouldn't have any issues returning it. A dead device is a dead device, the reps don't care. Also getting your new one unlocked should be no issue as all since you already had your first device unlocked. Just tell support that. Your device was unlocked and you had to RMA it. They will SIM unlock no problem. You will still have to wait 7 days for the unlock bin.
Click to expand...
Click to collapse
Wanna find out? I'll probably test in a few, lol.

hartleyshc said:
It's not how this tool works. A raw dump doesn't equal a flashable fastboot dump doesn't equal a msmdownloadtool ops file.
Edit: apparently you can't use the not equals symbol. I wrote a lengthy reply and it's gone. I'll write a shorter version.
My assumption is there is no version for the T-Mobile, but this will work for a full conversion. OP support will most likely not use this on the T-Mobile version and it's why we had to void our warranty when we unlocked the bootloader. They probably defer you to T-Mobile if you brick your phone. Now that being said, I bet this tool works just fine on the T-Mobile version and will turn it into a full international device capable of OTA updates and everything.
---------- Post added at 02:51 PM ---------- Previous post was at 02:43 PM ----------
One of three things will happen.
One, it will recognize it as the wrong device and won't flash as at.
Two, it will flash and you'll have a hard brick.
Three, it will flash and you'll have a fully converted International version.
If you have to return it to TMobile, you shouldn't have any issues returning it. A dead device is a dead device, the reps don't care. Also getting your new one unlocked should be no issue as all since you already had your first device unlocked. Just tell support that. Your device was unlocked and you had to RMA it. They will SIM unlock no problem. You will still have to wait 7 days for the unlock bin.
Click to expand...
Click to collapse
Cuz I'm assuming it's the same as Samsung. One hardware multiple softwares.
---------- Post added at 02:54 PM ---------- Previous post was at 02:53 PM ----------
Dark Nightmare said:
Wanna find out? I'll probably test in a few, lol.
Click to expand...
Click to collapse
Dude I will owe you one. Ur much braver than I. If my son falls asleep I'm trying to. PLEASE LET ME KNOW. And please let me buy u a beer lmfao

strictlyphat said:
Screw it. I'm gonna do this soon. Will report back
Click to expand...
Click to collapse
Guess I'll wait on your results...

Dark Nightmare said:
Guess I'll wait on your results...
Click to expand...
Click to collapse
I'm.having doubts man. Lol. What's your input. How likely I hard brick?

strictlyphat said:
I'm.having doubts man. Lol. What's your input. How likely I hard brick?
Click to expand...
Click to collapse
Since this will flash criticals, very likely, don't worry, my download is almost complete, I'll test it since my 6T is my spare device.

Dark Nightmare said:
Since this will flash criticals, very likely, don't worry, my download is almost complete, I'll test it since my 6T is my spare device.
Click to expand...
Click to collapse
Ah u r king. I had a backup iPhone til my daughter destroyed hers.

strictlyphat said:
Ah u r king. I had a backup iPhone til my daughter destroyed hers.
Click to expand...
Click to collapse
it fails, they do have a signature difference after all, I'm thinking we have to flash criticals/persist before this would work...maybe.

Dark Nightmare said:
it fails, they do have a signature difference after all, I'm thinking we have to flash criticals/persist before this would work...maybe.[/QUOTE
oof that sucks. thanks again
Click to expand...
Click to collapse

Safe flashing to anyone taking the plunge!

Dark Nightmare said:
it fails, they do have a signature difference after all, I'm thinking we have to flash criticals/persist before this would work...maybe.
Click to expand...
Click to collapse
tried it for good measure, same error

iaTa said:
This tool can be used to revive a bricked OP6T and remove the 'Device is corrupt' error message on boot.
Contains the latest MsmDownloadTool v4.0.58 and OOS v9.0.5 and is compatible with the non T-mobile international models (T-mobile compatibility currently unknown).
Make sure that your phone is switched off.
Open device manager on your Windows PC.
Press and hold the Volume Up & Volume Down buttons then connect to your PC using your data cable.
Once the device is connected to your Windows PC, check if the phone is being recognized (Other > QUSB_BULK or Ports > Qualcomm).
If showing as Other > QUSB_BULK either wait for Windows to install the Qualcomm driver or download the driver below and install.
Run MsmDownloadTool V4.0_factory.exe and click Start.
NOTE: This will completely wipe your device and relock your bootloader.
Downloads
MsmDownloadTool: https://androidfilehost.com/?fid=11410963190603846961
Driver: https://androidfilehost.com/?fid=24052804347798730
Shameless plug - my OP referral link for any peops that would like $20/£20/€20 discount: https://www.oneplus.com/invite#EC5BZVULJDUUO22
Click to expand...
Click to collapse
Oh my God you just saved my life brother. Thank you so much.

Dark Nightmare said:
it fails, they do have a signature difference after all, I'm thinking we have to flash criticals/persist before this would work...maybe.
Click to expand...
Click to collapse
Sad days... Appreciate the risks you've taken tho!!

TWRP - Need help downloading from Baidu

Can someone download this twrp and upload it to a mirror? It's for the Red Magic 3.
Password is: 6i3i
https://pan.baidu.com/s/1ZdMPjm2fEw...arentPath=/sharelink781715067-606770439204444

+6281281903288 contact me via whatsapp and i will share to you twrp file

tembokbesi said:
+6281281903288 contact me via whatsapp and i will share to you twrp file
Click to expand...
Click to collapse
OK at this point Ill try anything. I have my cell totally unlocked OEM an Bootloader an still have just a fastboot screen an little else no matter what I try and do.
I use whatsapp. Not sure how to add you or contact you through it?
The only thing i used it for was sending info to my boss
---------- Post added at 01:44 PM ---------- Previous post was at 01:43 PM ----------
Bryceicle1971 said:
OK at this point Ill try anything. I have my cell totally unlocked OEM an Bootloader an still have just a fastboot screen an little else no matter what I try and do.
I use whatsapp. Not sure how to add you or contact you through it?
The only thing i used it for was sending info to my boss
Click to expand...
Click to collapse
Edit: just found out how to add you

I already download twrp wait I share after some time

Any Twrp or EDL rom? Currently stuck in bootloop.

Samsung Note 8 (SM-N950F) Sim not Detecting after 01-July-2020 Patch Update

HI Friends,
Please help me to sort my Samsung Note 8 (SM-N950F) Sim not Detecting after 01-July-2020 Patch Update.
Factory Reset it but still the same.
Re-seat the the Sim Tray ,Tried Different sims but still have the same issue.
Please help me
Thank you.

Exactly same thing happened today.
Same thing happened with me today.
I tried factory reset.
I also tried flashing latest rom using Odin but got system version mismatch error. device 11 binary 10
It's better to wait for next firmware update.
Can't even boot into recovery now.
Will get back if I get anything working again.

sim not detected
Same issue with me. did all methods, but now stuck, have to wait for next update

poor update , same issue iv been stuck from 4pm once the update kicked in.
Service centre too closes early cos of the pandemic.
Avoid the update for the guys who havent updated it. July patch india

please help us to at least rollback.

isurues said:
please help us to at least rollback.
Click to expand...
Click to collapse
Have you tried flashing SCDTF1 FIRMWARE! That's the only firmware you can flash for now.
Look for either XEU OR BTU, don't worry about your CSC as long as you are using the multi-CSC OXM firmware your CSC will be supported.

Same issue here as well
Yes I did got same issue after update .... Contacted samsung but they dont have any solution .... pls keep all of us posted with the solution if any .... Actual problem is with IMEI number not displaying which prevents Network to come up .... this is what one of the samsung representative told me ....
Everyone pls keep posted for any update on this.

BluePhnx said:
Have you tried flashing SCDTF1 FIRMWARE! That's the only firmware you can flash for now.
Look for either XEU OR BTU, don't worry about your CSC as long as you are using the multi-CSC OXM firmware your CSC will be supported.
Click to expand...
Click to collapse
I have tried N950FXXSCDTF1_N950FOXMCDTF1_BTU from Sammobile.
then it will be SW REV. Check fail(Bootloader) error due to latest version of BL

vinaykdmp said:
Same thing happened with me today.
I tried factory reset.
I also tried flashing latest rom using Odin but got system version mismatch error. device 11 binary 10
It's better to wait for next firmware update.
Can't even boot into recovery now.
Will get back if I get anything working again.
Click to expand...
Click to collapse
try to flash ins firmware without csc (BL, Ap, CP).. phone will boot.. you can use with wifi... at least work without sim...

chanchal.shohel said:
try to flash ins firmware without csc (BL, Ap, CP).. phone will boot.. you can use with wifi... at least work without sim...
Click to expand...
Click to collapse
Tell me a thing if samsung will rollout an update for fixing this will sammobile get it at same time?

Can u explaing the process please
hainguyenthao said:
Just edit build.prop and flash AP file custom then it will be fixed no need to wait next update
Click to expand...
Click to collapse
Can u explain the process please

A new update has arrived. using samfirm to download it. Will update once I try Odin.
Edit: downloaded via samfirm and installed via odin. Back to normal!
ver N950FXXSDDTG5
no need to pay sammobile for fast speed. samfirm takes it directly from samsung server.

New update rolled out on Sammobile. have downloaded it, by paying 300rs. from paypal for fast download. phone is working fine. download the update of 29/07/2020.
Xda doesnt allow new users to post link. so u have to check on its page.

vinaykdmp said:
Same thing happened with me today.
I tried factory reset.
I also tried flashing latest rom using Odin but got system version mismatch error. device 11 binary 10
It's better to wait for next firmware update.
Can't even boot into recovery now.
Will get back if I get anything working again.
Click to expand...
Click to collapse
Your update section is functional? I can't even search for the updates, throws can't connect error!

Amijaz said:
Your update section is functional? I can't even search for the updates, throws can't connect error!
Click to expand...
Click to collapse
Have you updated? With the latest rom
---------- Post added at 05:53 AM ---------- Previous post was at 05:48 AM ----------
kunal_07 said:
A new update has arrived. using samfirm to download it. Will update once I try Odin.
Edit: downloaded via samfirm and installed via odin. Back to normal!
ver N950FXXSDDTG5
no need to pay sammobile for fast speed. samfirm takes it directly from samsung server.
Click to expand...
Click to collapse
Thankyou for updating, really appriciated.

nickme36 said:
Have you updated? With the latest rom
---------- Post added at 05:53 AM ---------- Previous post was at 05:48 AM ----------
Thankyou for updating, really appriciated.
Click to expand...
Click to collapse
Finally, flashed the latest fixed firmware. My eyes opened when the VoLTE icon appeared during the setup. Back to normal! Thank god.

kunal_07 said:
A new update has arrived. using samfirm to download it. Will update once I try Odin.
Edit: downloaded via samfirm and installed via odin. Back to normal!
ver N950FXXSDDTG5
no need to pay sammobile for fast speed. samfirm takes it directly from samsung server.
Click to expand...
Click to collapse
Can I do this at home without visiting service centre ??
Will I lose data after you apply this update ? I mean do I need to do factory reset to apply this latest update ??

Official process which Samsung told me to do
NOTE:-
We do not have confirmation regarding WILL DATA BE LOST OR NOT
STEP 1:-
Kindly follow these steps Phone should be in Switch OFF state, follow the procedure as below: Long press “Volume Down + Power Key + Bixby Key”
STEP 2:-
After warning message will be displayed as shown in above image. Press the Volume up button and device will go to same state as shown. Connect the phone to laptop/desktop via USB Cable.
STEP 3:-
Click on the link and download 2 files in one Folder https://www.mediafire.com/folder/o2u26wfcpdz68/
STEP 4:-
After that Install Smart switch application in laptop/desktop before proceeding further (https://www.samsung.com/in/support/smart-switch/)
STEP 5:-
Connect device with laptop/desktop using USB cable
STEP 6:-
Double click “N950FXXSDDTG5” exe file which is downloaded from the link
STEP 7:-
After that Tool will be opened as shown below. Click “Start” Button
STEP 8:-
If “Pass” is displayed on tool screen as below then device will return to home screen after some time.

has anyone tried this method? please let me know if its working
---------- Post added at 05:11 PM ---------- Previous post was at 05:09 PM ----------
jazzydedania728 said:
NOTE:-
We do not have confirmation regarding WILL DATA BE LOST OR NOT
STEP 1:-
Kindly follow these steps Phone should be in Switch OFF state, follow the procedure as below: Long press “Volume Down + Power Key + Bixby Key”
STEP 2:-
After warning message will be displayed as shown in above image. Press the Volume up button and device will go to same state as shown. Connect the phone to laptop/desktop via USB Cable.
STEP 3:-
Click on the link and download 2 files in one Folder https://www.mediafire.com/folder/o2u26wfcpdz68/
STEP 4:-
After that Install Smart switch application in laptop/desktop before proceeding further (https://www.samsung.com/in/support/smart-switch/)
STEP 5:-
Connect device with laptop/desktop using USB cable
STEP 6:-
Double click “N950FXXSDDTG5” exe file which is downloaded from the link
STEP 7:-
After that Tool will be opened as shown below. Click “Start” Button
STEP 8:-
If “Pass” is displayed on tool screen as below then device will return to home screen after some time.
Click to expand...
Click to collapse
The link seems very fishy, should i trust this or report it.

SIM card not getting detected samsung note 8 SM-N950F
after the new update, for Samsung note 8 model SM-N950F
sim cards are not detectable,
IMEI number not available
not able to login to Samsung account
the software update on settings won't connect to Samsung servers now,
just wifi works,
Did factory reset, cleared all cache, no use, still the same.
plz any helps, i am stuck as i in a different country, none of the phones here as an issue, so they don't even know there is a problem,
---------- Post added at 06:49 PM ---------- Previous post was at 05:50 PM ----------
Rulinglionadi said:
has anyone tried this method? please let me know if its working
---------- Post added at 05:11 PM ---------- Previous post was at 05:09 PM ----------
The link seems very fishy, should i trust this or report it.
Click to expand...
Click to collapse
thisssss workssssssss :good::good::good::good::good: